ViewEra Computer Monitor V140 User Manual

ViewEra  
14TFT-LCD MONITOR  
V140  
USERS MANUAL  
 
Product Features  
Additional  
High contrast color TFT LCD display support resolution up to XGA  
Read all of these instructions and save them for later use.  
1024×768. @75Hz.  
Follow all warnings and instructions on the product.  
Product  
Compatible VESA standards.  
Imbedded audio system provides sound performance.  
Power management system conforms to VESA DPMS standard.  
Support DDC 1/2B for Plug & Play compatibility.  
Advanced OSD control for picture quality adjustment.  
Detachable stand for wall-mounting application.  
Do not cover block the vent holes in the case.  
Do not insert sharp objects or spill liquid into the LCD monitor through  
cabinet slots. They may cause accident fire, electric shock or failure.  
Disconnect the power plug from the AC outlet if you will not use it for  
an extended period of time.  
Do not attempt to service this product yourself, as opening or removing  
covers may expose you to dangerous voltage points or other risks.  
Do not touch the screen directly with your fingers. You may damage the  
screen, and oil from your skin is difficult to remove.  
Do not apply pressure to screen. The LCD is very delicate.  
Power  
Screen cleaning techniques  
Gently clean the screen with a clean camel hair lens brush, or a soft,  
clean, lint-free cloth, to remove dust and other particles that can scratch  
the screen.  
Do not apply pressure to the screen surface when wiping it clean.  
Do not pour or spray any liquid directly onto the screen or casing.  
Chemical cleaners have been reported to damage the screen or case of  
the LCD monitor.  
Use the type of power indicated on label.  
Plugs  
Do not remove any of the prongs of the monitors three-pronged power  
plug.  
Disconnect the power plug from the AC outlet under following  
conditions:  
If you will not use it for an extended period time.  
When the power cord or plug is damaged or frayed.  
If the product does not operate normally when the operating  
instructions are followed. Adjust only those controls that are  
covered by the operating instructions. Improper adjustment of other  
controls may result in damage and will often require extensive work  
by a qualified technician.  
If the product exhibits a distinct change in performance, service may  
be required.  
Page 2  
Page 3  
 
2. Control Function  
Control Button Front View  
Power and extension cords  
Do not allow anything to rest on the power cord.  
Do not locate this product where persons will walk on the cord.  
Use the proper power cord with correct attachment plug type. If the  
power source is 120V AC, use a power cord that has UL and C-UL  
approvals, If the power source is a 240V AC supply, use the tandem (T  
blade) type attachment plug with ground conductor power cord that  
meets the respective European countrys safety regulations, such as VDE  
for Germany.  
2﹞ ﹝3﹞ ﹝1﹞ ﹝4﹞ ﹝5﹞  
Do not over load wall outlets or power cords. Ensure that the total of all  
units plugged into the wall outlet does not exceed 10 amperes.  
Ensure that the total ampere ratings on all units plugged into the extension  
cord is not above the cords rating.  
If the power supply cord, which came with your monitor, is to be  
connected to the PC instead of the wall outlet, Use an UL/TUV approved  
computers with receptacle rated 100~240V AC, 50/60Hz, 1.0A(minimum)  
only.  
1.Power Switch  
2. Auto adjust  
Power switch & LED.  
Select this function to obtain the best display  
efficiency  
3.OSD menu / select  
4.Adjust (decrease)  
5.Adjust (increase):  
Pressing this button pops up the OSD menu  
on the screen Add used to select the OSD  
control options on the screen.  
Environment  
Place the monitor on a flat and leveled surface.  
Place the monitor in a well-Ventilated place.  
This button is used to adjust the decreasing  
value of selected.  
Keep the monitor away from:  
Overly hot, cold or humid places, places directly under sunlight, dusty  
surroundings, equipment that generate strong magnetic fields.  
Please adjust the frequency to 75 Hz after setting up the LCD monitor.  
Then push the OSD menu button and use the Auto Adjust function to find  
the best mode of your computer.  
OSD off is volume adjust -  
This button is used to adjust the increasing  
value of selected.  
OSD off is volume adjust +  
Page 4  
Page 5  
 
OSD Controls  
Picture Menu:  
Auto adjust  
Select this function to efficiently obtain the best  
display solution.  
Monitor Function Selection Menu  
Brightness  
Contrast  
Reset  
Adjust the brightness usingandbuttons.  
Adjust the contrast usingandbuttons.  
Recall Factory setup function.  
PICTURE  
Select this function to Picture sub menu.  
ADVANCED PIC Select this function to Advanced Picture sub  
Exit  
Return to Selection menu.  
menu.  
SOUND  
Select this function to Sound sub menu.  
UTILITY  
EXIT  
Select this function to Utility sub menu.  
Select this function to exit OSD menu.  
Sub Menu (Auto adjust):  
Accept  
Retry  
Select this function to accept auto adjust.  
Select this function to retry auto adjust.  
Cancel  
Select this function to cancel auto adjust.  
Page 6  
Page 7  
 
Sound Menu:  
Volume  
Mute  
Adjust the volume usingandbuttons.  
Mute function.  
Exit  
Return to Selection menu.  
Advanced Picture Menu :  
Pressingmoves the display image to right ; Pressing  
moves the display image to left.  
H Position  
V Position  
Pressingmoves the display image upward ; Pressing  
moves the display image downward.  
Phase  
Clock  
Adjust the phase usingandbuttons.  
Adjust the clock usingandbuttons.  
Utility Menu:  
Auto Color Select this function to obtain the best display color.  
Exit  
Return to Selection menu.  
OSD Language  
Select the Language Letter Font.  
Select this function to OSD control sub menu.  
OSD Control  
Exit  
Return to Selection menu.  
Page 9  
Page 8  
 
3.Input Diagrams  
Inputs  
AUDIO】  
OS Language Menu:  
AVI】  
English I  
ENGLISH II  
Exit  
Select Small Letter Font.  
Select Capitalize Letter Font.  
Return to Utility Menu.  
1】 【2】 【3】 【4】 【5】  
6】  
1DC IN  
This is for connecting the adapter DC 12V cable.  
2AV IN  
RCA jack AV signal input.  
S-Video signal input.  
3S-VIDEO IN  
4LINE OUT  
Sound signal output(Stereo Phone Jacket).  
Audio signal R/L input.  
OSD Control Menu :  
5RCA JACK  
AUDIO IN  
Pressingmoves the OSD menu to downward ;  
Pressingmoves the OSD menu to upward.  
V Position  
H Position  
6VGA IN  
This can be connected with the D-sub 15 pin  
signal connector.  
Pressingmoves the display image right ; Pressing  
moves the display image left.  
Halftone  
Duration  
Reset  
Adjust the shade of the OSD menu.  
Adjust the OSD show time.  
Recall Factory setup function.  
Return to Utility menu.  
Page 10  
Exit  
Page 11  
 
4. Setup  
Electrical Connection  
5. Viewing Angles  
Tilting  
Please follow the instruction below to properly connect the LCD monitor  
to external electrical source.  
For better viewing angle, you may tile the LCD monitor forwards (up to 10  
degrees) or backwards (up to 25 degrees, 90 degrees for packing).  
1. Connect the female-end of the power cable to the transformer. Connect  
the male-end of the power cable to the wall outlet or extension cable.  
2. Connect the cable from the other end of the transformer to the LCD  
monitor located at the back near the VGA signal cable.  
Signal Connection  
Down10 o  
1. Power off both the LCD monitor and PC system before connecting them.  
2. Take out the VGA cable from the box, then connect it to the signal  
connector at the back of the LCD monitor.  
3. Connect the other end to the VGA connector on the back of the PC  
system.  
4. Please make sure the connections between the PC system unit and the  
LCD monitor is strong and secure. Please dont forget to tighten the  
screws on each connector end.  
5. Now turn on both the PC system unit and the LCD monitor.  
6. After you finish setting up the LCD monitor, please set the refresh rate to  
75Hz.  
7. After setting up the LCD monitor, please perform Auto Adjust in OSD so  
that the LCD monitor will automatically set to optimum color display  
each time.  
Up25 o  
* Please note: When you disconnect any power cable or signal cable, please  
do not pull the cable by grabbing the cable body. Please grab the cable  
connector itself whenever you try to pull the cable during disconnect.  
Page 12  
Page 13  
 
6. Troubleshooting  
8. Product Specifications  
No power  
Make sure the A/C power cord is securely connected to the monitor and to the  
power outlet.  
Type  
AUDIO  
DVI  
Spec  
No screen image with power on  
LCD Display  
Pixel Pitch  
Max. Resolution  
Set Size  
14.1Active matrix TFT LCD panel  
0.279(H) x 0.279(V) mm  
(1)Make sure the video cable supplied with the monitor is tightly secured to  
both the video output port of the computer and the monitor.  
(2)Adjust the brightness and contrast from the front panel controls.  
No Signal Inputmessage shown  
1024(H) x 768(V) XGA  
375(W) × 360(H) × 185(D) mm  
Pack Size  
422(W) × 426(H) × 214(D) mm  
200:1 (option 300:1)  
150 cd/m2 (option 200)  
25 ms (typ)  
(1)Make sure the video cable is tightly connected to the computer and  
monitor.  
Contrast Ratio  
Brightness  
(2)Check the 15-pin video cable connectors on both ends have exactly 15  
pins.  
Response Time  
Display Color  
View Angle  
262,144  
L+/R- ±50°  
U+/D- +20° -35°  
If the problem is still there, please contact your ViewEra dealer or ViewEra.  
PC Interface  
Video Sync.  
Display Mode  
RGB analog or digital 0.7V peak to peak  
TTL positive or negative.  
VGA, SVGA, XGA  
7.Service Information  
Warranty  
Power consumption ON<36W (maximum)  
Frequency  
(Horizontal) 31.5-60KHz (Vertical) 56-75Hz  
The ViewEra V140 TFT-LCD monitors are warranted for three(3) years  
for all parts and one(1) year for LCD panels from the date of purchase.  
ViewEra warrants its products to be free from defects in material and  
workmanship during the warranty period.  
Signal Connector  
Front Control  
D-sub 15 pin and CVBS / S-Video (O\option)  
Auto adjust, Power SW with LED, OSD Menu,  
/Adjustment  
OSD Menu  
Brightness, Contrast, Auto Adjust, Clock, Phase,  
H-Position, V-Position,  
Service  
(1) Please contact your ViewEra dealer for warranty service.  
(2) For out-of-warranty service, you may contact either ViewEra dealers or  
ViewEra.  
Power Adapter  
AC Input : 100-240V~1.8A, 50-60Hz  
DC Output : 12V/ 3.0A  
Page 15  
Page 14  
 
9. Windows setup  
Operating  
Conditions  
Storage  
Temperature: 0~40℃  
Humidity : 20% ~ 85%  
For the best view, please set up with the monitor type in Windows.  
Please select as follows:  
Temperature: -20~60℃  
Conditions  
Certification  
Weight  
Humidity : 10%~95%  
Control Panel > Monitor > Setting > Advance > Monitor > Change >  
Show all List > Stand >  
BSMI,FCC (DOC), CE-B, TUV/GS, UL,CUL  
Net3.25Kgs, Gross5.05Kgs  
For 1024 ×768, please set to XGA 1024 × 768@75Hz”  
Display Modes  
Mode  
Resolution  
H Freq (KHz)  
31.469  
31.469  
37.861  
37.500  
31.469  
35.156  
37.879  
48.077  
46.875  
48.363  
56.476  
60.023  
V Freq (Hz)  
1
2
640 × 350  
640 × 480  
640 × 480  
640 × 480  
720 × 400  
800 × 600  
800 × 600  
800 × 600  
800 × 600  
1024 × 768  
1024 × 768  
1024 × 768  
70.070  
59.940  
72.809  
75.000  
70.087  
56.250  
60.317  
72.188  
75.000  
60.004  
70.069  
75.029  
3
4
5
6
7
8
9
10  
11  
12  
ViewEra V140 Rev. 1.1  
CWS4UMB50031  
Page 17  
Page 16  
 

Technicolor Thomson Camcorder VMD 6 User Manual
Toshiba Laptop toshiba satellite l550 satellite pro l550 satellite l550d satellite pro l550d series User Manual
Toshiba Network Card PSAFGU 055002 User Manual
TP Link Switch TL SL2428WEB User Manual
Traulsen Refrigerator RHT232NUT FSL User Manual
Ultimate Support Systems Microphone 17215T User Manual
Vivotek Digital Camera FD6121V User Manual
Vulcan Hart Griddle 924RE 936RE 948RE 960RE 972RE ML 135221 00G24 ML 135222 00G36 ML 135223 00G48 ML 135224 00G60 ML 135225 00G72 User Manual
Wasp Bar Code Scanner WLR8900 Series User Manual
Weber Gas Grill 56203 User Manual