Viking Cordless Telephone K 1900 User Manual

K-1900 Series

TECHNICAL

Hot Line Phones

Practice

June 27, 2002

TELECOM SOLUTIONS FOR THE 21ST CENTURY

Economical and Vandal Resistant

Hot-Line Phones

The K-1900 Series of Hot-Line phones are pro-

grammable to dial a 1-20 digit telephone number

each time the phone’s handset is lifted. The prod-

K-1900-6

ucts may be programmed to Touch Tone

or pulse dial and will not dial on incoming

calls.

K-1900D-2 ASH

K-1900-7

The K-1900 Series phones are available

in a desk or wall chassis, as well as in a

vandal resistant panel phone configuration. A

network insert dialer is also available, to convert

standard phones into hot-line phones.

K-1900W-2

K-1900W-2 ASH

K-1900D-2

Applications

• Catalog sales

Features

• Information kiosks in malls

• Courtesy and customer service phones

• Automated tellers

• Telephone line powered

• Hearing aid compatible amplified handsets

• Rotary handset volume control

• 1 - 20 digit programmable speed dial number

• Touch Tone and 10/20 pps pulse dialing

• Non-volatile E²memory (no batteries

required)

• Hot-line reservation phones

• Replace leased Ringdown circuits

• Security and emergency phones (pools, etc.)

• Restricts fraudulent calls from hand held

dialers

Phone...715.386.8861

onics.co

ingelectr

• K-1900D/W-2 available in red or ash

• Optional Q170600 ringer (Fax Back Doc 845)

• Operates on a C.O. line or analog PABX/KSU

extensions

info@vik

http://www.vikingelectronics.com

• Ring detection (will not dial on incoming calls)

• Programmable security code to enter

programming mode

• Touch Tone programmable

• K-1900-6 fits standard 500, 554, 2500 and

2554 set phones

Specifications

Power: Telephone line powered (20V DC/18mA minimum)

Environmental: 0°C to 32°C (32°F to 90°F) with 5% to 95%

non-condensing humidity

Dimensions: (see page 2)

Dialing Speed: Normal - 120ms tones/10 pps, Fast - 50ms

tones/20 pps

Programming

While in the programming mode, two beeps indicate a valid programming entry. An invalid entry will be indicated with three

beeps. To exit programming, simply hang-up the K-1900 Series phone.

A. Accessing the Programming Mode

1. Using the Security Code

Step 1. Connect the K-1900 Series device to an analog C.O. line, or an analog PABX/KSU station.

Step 2. From a Touch Tone phone, call into the K-1900 Series phone.

Step 3. Listen for at least one ringback in the calling phone and then take the K-1900 Series phone off-hook (answer the

phone).

Step 4. From the Touch Tone phone, enter your six digit security code (factory set to 845464 - see section E).

Step 5. A double beep indicates the K-1900 Series phone is in the programming mode (see sections B-G ). If six digits are

entered and no beeps are heard, an incorrect security code has been entered. Repeat steps 2-5 or follow directions

in 2. Without a Security Code below.

2. Without a Security Code (If You Have Forgotten or Lost the Security Code)

Step 1. Remove JP1 (as shown to the right). For the K-1900W-2 and K-1900D-2, the

plastic cover must be removed to expose the circuit board.

Step 2. Connect the K-1900 Series device to a C.O. line, analog PABX/KSU station or

JP1

to a DLE-200B Line Simulator.

Remove to

Step 3. From a Touch Tone phone, call into the K-1900 Series phone.

enter program-

ming without a

security code.

Step 4. Listen for at least one ringback in the calling phone and then take the K-1900

Series phone off-hook (answer the phone).

Step 5. A double beep indicates the K-1900 Series phone is in the programming mode

(see Programming sections B-G).

Note: JP1 MUST be in place for

normal operation.

Step 6. When programming is finished, replace JP1 and replace cover on phone.

Memory

Location

B. Quick Programming Guide

then

Enter Digits

Speed dial number (see section C) 1-20 digits or pauses ............................................. phone number then

Security Code, factory set to 845464 (see section E) ................................................... 6 digits

then

✱✱

To add a ✱ anywhere in the dialing string .....................................................................

To add a # anywhere in the dialing string ...................................................................... ✱#

To set dialing speed to normal - 120ms tones/10 pps (factory setting) .......................... ✱1

To set dialing speed to fast - 50ms tones/20pps ........................................................... ✱2

To restrict Touch Tone user dialing (factory setting) ...................................................... ✱3

To enable Touch Tone user dialing ................................................................................ ✱4

Toggles between pulse and Touch Tone dialing (see section C) ................................... ✱6

To add a 4 second pause anywhere in the dialing string (see section C) ...................... ✱7

To add a 1 second pause anywhere in the dialing string ............................................... ✱8

C. Programming Examples

Step 2 - Enter Digits

To Program the ACD-10 to...

Step 1 - See section A

Enter Programming

5551234 + #0

...to Touch Tone dial 555-1234

✱6 5551234 ✱6 9 + #0

...to pulse dial 555-1234 followed by a Touch Tone 9

...to dial a 9, a 4 second pause and then 555-1234

...to set the dialing speed to fast

9 ✱7 5551234 + #0

✱2

✱4

...to enable unlimited user dialing after the phone has speed dialed

...to clear the speed dial number or disable speed dialing

D. Touch Tone and Pulse Dial Speeds

The K-1900 Series phone can be programmed to dial at normal or fast dialing speeds. While in the programming

mode, enter ✱1 for normal dialing speed - 120ms on/off Touch Tones or 10 pps pulse dialing. Enter ✱2 for fast dialing

speed - 50ms on/off Touch Tones or 20 pps pulse dialing.

E. Security Code

A six digit security code is required to access the programming mode. The factory set security code is 845464 (V-I-K-

I-N-G). It is recommended that you change the security code to a personal 6 digit (0-9) number in memory position #9

while in the programming mode. Note: The security code must be six digits in length and cannot contain a ✱ or #.

F. Touch Tone or Pulse Dialing

The K-1900 Series phones are factory set to automatically dial using Touch Tones. A ✱6 entered in the speed dial num-

ber will toggle the dialing mode between Touch Tone and pulse (see section C).

Note: You can NOT program a ✱ and # to be pulse dialed.

G. Touch Tone User Dialing Restriction (factory enabled)

The K-1900 Series phones is factory set to restrict fraudulent calls from hand held pocket dialers. After speed dialing,

the K-1900 Series phones will restrict (hang up) when they detect any Touch Tone that they did not generate. To restrict

user dialing, enter ✱3 while in the programming mode. To enable user dialing, enter ✱4 while in the programming mode.

Adding an Internal Ringer

.47 mF @ 250V

(included with ringer)

An optional Q170600 internal ringer is available. For more informa-

tion, retrieve Fax Back Document 834.

Q170600

Electronic Ringer