Viper Universal Remote G5102V User Manual

Model 5601

Security and Remote Start

Owner’s Guide

G5102V 2008-06

Contents

Government regulations.....................................................................................5

Warning! Safety first .........................................................................................7

What is included.............................................................................................10

Important information ......................................................................................10

Your warranty.........................................................................................10

Replacement remotes...............................................................................11

System maintenance ...............................................................................11

Low battery indicator ..............................................................................11

Battery Replacement................................................................................11

Two Car Operation.................................................................................11

1-way remote .................................................................................................13

Transmitter configuration..........................................................................14

Feature List:............................................................................................15

Using the system .............................................................................................18

Arming the system...................................................................................18

While the system is armed.......................................................................18

Modified Arming Modes..........................................................................20

Disarming the System..............................................................................21

System override......................................................................................22

Valet mode ............................................................................................23

Remote feature programming ...................................................................23

Using the remote start......................................................................................25

Remote starting your vehicle.....................................................................25

Manual transmission vehicles ...................................................................26

Timer mode............................................................................................27

Turbo timer mode....................................................................................28

Smart start .............................................................................................29

Turning on the rear defogger....................................................................30

Valet take-over........................................................................................31

Safety features ...............................................................................................32

Starter anti-grind circuitry.........................................................................32

Disabling the remote start system..............................................................32

Diagnostics ....................................................................................................33

Arming .................................................................................................33

Disarming .............................................................................................34

System status chirps ...............................................................................34

Table of zones........................................................................................34

Interpreting zone diagnostics....................................................................35

Nuisance prevention® circuitry ................................................................35

Owner recognition .........................................................................................37

Rapid resume logic..........................................................................................37

Power saver mode...........................................................................................38

Programming options.......................................................................................39

Security & convenience expansions...................................................................41

Glossary of terms............................................................................................43

Quick reference guide.....................................................................................45

Notes ............................................................................................................47

Limited lifetime consumer warranty....................................................................49

Government regulations

This device complies with Part 15 of FCC rules. Operation is subject to the fol-

lowing two conditions: (1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that

may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential instal-

lation. This equipment generates and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television, which can be determined by

turning the equipment OFF and ON, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

To satisfy FCC RF exposure compliance requirements, this device should be used

in hand-held, hand operated conﬁgurations only. The device and its antenna

must maintain a separation distance of 20 cm or more from the person’s body,

except for the hand and wrists, to satisfy RF exposure compliance. This device

is designed to be used in a person’s hands and its operating conﬁgurations do

not support normal transmissions while it is carried in pockets or holsters next to

a persons’ body.

This device complies with the Industry Canada Radio Standards Speciﬁcation

RSS 210. Its use is authorized only on a no-interference, no-protection basis; in

other words, this device must not be used if it is determined that it causes harm-

ful interference to services authorized by IC. In addition, the user of this device

must accept any radio interference that may be received, even if this interference

could affect the operation of the device.

WARNING! Changes or modiﬁcations not expressly approved by the party re-

sponsible for compliance could void the user’s authority to operate this device.

Warning! Safety ﬁrst

The following safety warnings must be observed at all times:

Due to the complexity of this system, installation of this product must only be

performed by an authorized Directed dealer.

When properly installed, this system can start the vehicle via a command signal

from the remote control transmitter. Therefore, never operate the system in an

enclosed area or partially enclosed area without ventilation (such as a garage).

When parking in an enclosed or partially enclosed area or when having the

vehicle serviced, the remote start system must be disabled using the installed

toggle switch. It is the user’s sole responsibility to properly handle and keep out

of reach from children all remote control transmitters to assure that the system

does not unintentionally remote start the vehicle. THE USER MUST INSTALL A

CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJA-

CENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING

AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE

AREA MUST AT ALL TIMES REMAIN CLOSED. These precautions are the sole

responsibility of the user.

Remote starters on manual transmission vehicles operate differently than those

with automatic transmission because you must leave your car in neutral. You

must read this Owner’s Guide to familiarize yourself with the proper procedures

regarding manual transmission remote starters. If you have any questions, ask

your installer or contact Directed at 1-800-753-0600.

Before remote starting a manual transmission vehicle, be sure to:

•

Leave the vehicle in neutral and be sure no one is standing in front or

behind the vehicle.

•

Only remote start on a ﬂat surface

Have the parking brake fully engaged

WARNING! It is the responsibility of the owner to ensure the parking/emergen-

cy brake properly functions. Failure to do so can result in personal injury or prop-

erty damage. We recommend the owner have the parking / emergency brake

system inspected and adjusted by a qualiﬁed automotive shop bi-annually.

Use of this product in a manner contrary to its intended mode of operation may

result in property damage, personal injury, or death. (1) Never remotely start the

vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with

the keys in the ignition. The user must also have the neutral safety feature of the

vehicle periodically checked, wherein the vehicle must not remotely start while

the car is in gear. This testing should be performed by an authorized Directed

dealer in accordance with the Safety Check outlined in the product installation

guide. If the vehicle starts in gear, cease remote start operation immediately and

consult with the authorized Directed dealer to ﬁx the problem.

After the remote start module has been installed, contact your authorized dealer

to have him or her test the remote start module by performing the Safety Check

outlined in the product installation guide. If the vehicle starts when performing

the Neutral Safety Shutdown Circuit test, the remote start unit has not been

properly installed. The remote start module must be removed or the installer must

properly reinstall the remote start system so that the vehicle does not start in gear.

All installations must be performed by an authorized Directed dealer.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN

GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERAT-

ING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT

IN PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMMEDIATELY

CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AU-

THORIZED Directed DEALER TO REPAIR OR DISCONNECT THE INSTALLED

REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR

PAY FOR INSTALLATION OR REINSTALLATION COSTS.

This product is designed for fuel injected vehicles only. Use of this

product in a standard transmission vehicle must be in strict accordance

with this guide.

This product should not be installed in any convertible vehicles, soft or

hard top with a manual transmission. Installation in such vehicles may

pose certain risk.

What is included

•

Two ﬁve-button remote controls

The control module with Stinger™ DoubleGuard® two-stage

shock sensor

•

Control center with integrated status LED and Valet override

switch

•

Revenger™Soft Chirp™six-tone siren

A remote start defeat toggle switch

Window decals

Your warranty registration

Important information

Congratulations on the purchase of your state-of-the-art remote start and

alarm system. Due to the complexity of this system, it must be installed

by an authorized dealer only. Installation of this product by anyone

other than an authorized dealer voids the warranty. All dealers are

provided with a preprinted dealer certiﬁcate to verify authorization.

By carefully reading this Owner’s Guide prior to using your system,

you will maximize the use of this system and its features. You can print

additional or replacement copies of this manual by accessing our web

site at www.directed.com

➤ Your warranty

Your warranty registration must be completely ﬁlled out and returned

within 10 days of purchase. Your product warranty will not be validat-

ed if your warranty registration is not returned. Make sure you receive

the warranty registration from your dealer. It is also necessary to keep

your proof of purchase, which reﬂects that the product was installed by

an authorized dealer.

➤ Replacement remotes

Your system comes with two Responder remote controls (P/N 7153V).

If additional remotes are desired, please see your authorized dealer or

visit www.directedstore.com to order.

➤ System maintenance

The system requires no speciﬁc maintenance. Your One way remote

is powered by small coin cell lightweight 3-volt lithium battery that will

last approximately one year under normal use. The remote uses one

CR2032 cell battery. When the battery begins to weaken, the operat-

ing range will be reduced.

➤ Low battery indicator

When the batteries are low the alarm then emits an additional chirp

upon disarming of the alarm to let you know its time to change the

remote battery.

Note: The Arm/Disarm chirps should be programmed ON for the

alarm to emit any additional chirps during disarm. Ask your authorized

dealer if you have any questions.

➤ Battery Replacement

Slide the door up to expose the battery beneath the holder. Remove the

expired battery. Place the new battery into the remote control. When

power is returned the remote control is ready for use.

➤ Two Car Operation

You can use the remote control system for two cars with full command

capability for both vehicles.

To change the car selection:

•

Press and hold the

button until the amber light blinks once or

twice indicating current vehicle.

one blink & beep = car 1.

Two blinks & beeps = car 2

•

To scroll from one car to the other press the

button again. After

selecting the car, operation of other features can resume. The se-

lected car remains selected until this setting is changed.

1-way remote

Description

Transmit indicator

Lock button

Feature

Press for one second to arm.

Unlock button

Press for one second to disarm.

Remote start

button

Press for one second to activate remote

start.

Auxiliary

button

Press and hold for 1.5 second to activate

trunk release.

Function

button

Allows access to programming and

modifies operation of the other buttons.

Label

Back of remote has label to identify the

remote as 2-way or 1-way

Battery Door

Remove to access batteries when neces-

sary.

Note: If Keypad Lock is On, press and then press

to exit.

➤ Transmitter conﬁguration

Direct Access

Level

x 1

x 2

x 3

x 4

Button

Arm/Lock

Silent Arm

Sensor

Bypass **

Silent Alarm

Sensors †

Silent Alarm

All Zones †

(Panic)

Disarm/Unlock Silent Disarm Valet On/

Car Finder

(Panic)

Off

Timer Mode Smart Start

Starter

Reset

Defogger

On/Off

Runtime

On/Off

Trunk Release

AUX 1

AUX 2

AUX 3

***

(Red/White)

Advance Level

Change Car

(3s) Enter

Request

Temperature

* †

Runtime

Remaining

* †

Event His-

tory Report

* †

programming

(8s) *

button must be pressed and held to access state

System must be in ARMED mode to access this feature

System must be in remote start mode to access this feature

Only applicable when upgrading to two way remote

***

†

Note: Pressing more than one button simultaneously generates an Error

tone and the LED ﬂashes.

➤ Feature List:

Arm

Command

Press one time to Arm

Notes

Press/hold for 1.5 seconds to Arm the system and then

activate the Panic output

Disarm

Command

Press one time to Disarm

Remote Start

Command

Press one time to activate Remote Start

Aux (trunk)

Command

Press one time to open Trunk

Function shift

Command: Press 1 to 4 times. ( See Function shift table)

Notes

Each Press then release, shifts the function of the com-

mand button.

Silent arm

Command: Press

Notes Arms the system without chirps

one- time and then press

Silent disarm

Command

Press

one- time and then press

Notes

Disarms the system without chirps

Runtime reset

Command

Press

one-time and then

Notes

Re-starts the remote start runtime counter if remote start is

active.

Aux 1

A U X

Command

Press

one time and then press

Notes

This is an optional feature. See your sales rep/installer

for details.

Aux 2

A U X

Command: Press

two times and then press

Notes

This is an optional feature. See your sales rep/installer

for details.

Aux 3

A U X

Command: Press

three times and then press

Notes

This is an optional feature. See your sales rep/installer

for details.

Sensor Bypass

Command: Press

Notes

two- times and then

Available when armed only: bypasses warn triggers.

Send again to bypass Warn & Full Trigger; Send again

to turn bypass off and monitor sensors normally. For more

information, see Modiﬁed Arming Modes.

Valet mode

Command: Press

two-times and then

Timer mode

Command: Press

two-times and then

Notes

Enables or disables the remote start timer mode.

Car finder

Command: Press

Notes Arm/Disarm cancels the light ﬂashes.

three-times and then

Smart start

Command: Press

Notes Enables or disables the SmartStart feature.

three-times and then press

Defogger

Command: Press

start is on.)

four times, and then

. (Only after remote

Notes

Automatically turns on during remote start. The rear de-

fogger (if connected) is programmed to automatically

activate when remote start is turned on. If the interior

cabin temperature is above 55˚ F the defogger will not

activate.

Panic

Command: Press and hold

for 1.5 seconds.

Notes

The siren will trigger until you hit the lock or unlock button

on the remote

Using the system

➤ Arming the system

To arm the system, press the

button on the remote control.

The siren in the vehicle will “chirp” once and the parking lights will ﬂash

once. If the power door locks have been connected, the doors will

lock. The system will automatically check for errors when it arms.

If errors are found when arming:

If an alarm trigger zone – such as a door, the trunk, the hood, or a

sensor, was active at the time of arming, the system will “bypass”, or

ignore, this trigger zone. This allows the system to continue to protect

your vehicle using the remaining trigger zones.

You are notiﬁed of this active zone immediately after arming the system.

The siren in the vehicle will “chirp” again and the parking lights will

ﬂash again. The Status LED indicator in the vehicle will blink in a pattern

to indicate the active zone number error which was found (See Table

of Zones on page 34).

Arming without the chirp (Silent Arm):

Press the

button at the bottom of the remote once, and then press

the button. The system will arm without the conﬁrmation chirp. The

parking lights will ﬂash once.

➤ While the system is armed

•

Fail-Safe Starter Kill

The starter is disabled by the system’s Fail-Safe starter kill (if installed).

Alarm Responses

The security system can generate two levels of alarm: Warn Away - Soft

siren chirps and ﬂashing parking lights.

The purpose of Warn-Away is to warn a would-be thief next to your

vehicle that the vehicle is protected, but in a manner that does not call

attention to it from more than a few feet away.

Full Alarm Trigger

Sounds the siren at maximum volume and ﬂashes the parking lights.

The default duration of the Full Alarm is 30 seconds. This can be pro-

grammed to any duration from 30 to 60 seconds manually. Ask your

authorized dealer for details.

Warn-Away response is triggered by:

•

Lesser or lighter vibrations or impacts (detected by the Stinger

Doubleguard shock sensor)

Opening a door: the Progressive Door Trigger feature will sound

the Warn Away response, followed immediately by Full Alarm

Any attempt to start the car: the Progressive Ignition Trigger will

ﬁrst sound the Warn Away response, followed immediately by Full

Alarm.

•

An optional Proximity Sensor (508D) triggered in the outer zone.

Full Alarm response is triggered by:

•

Heavier impact to the vehicle (detected by the Stinger Double-

Guard shock sensor).

•

Opening the trunk or hood (if connected).

Opening a door: the Progressive Door Trigger feature will ﬁrst

sound the Warn-Away response, followed immediately by Full

Alarm.

•

An optional sensor, such as an optional Proximity Sensor triggered

in the inner zone.

Note: Call the police immediately if you witness a crime in progress.

➤ Modiﬁed Arming Modes

The Responder gives you an unprecedented level of control over how

it will protect your car. “Normal arming” means that all the Responder

security features are active automatically. You can turn some security

features off on a one-time basis.

Turning off the Warn Away response

1. Arm system

2. Press the

3. Press the

button twice.

button.

Now, slight impacts or vibrations will not trigger Warn-Away. Heavy

impacts will still trigger Full Alarm.

Note: The next time you arm the system, Warn-Away will work

normally.

Turning off the Sensor Full Trigger response

You can completely disable the Stinger Doubleguard Shock Sensor

and any added optional sensors on a one-time basis. The entry points

(doors, hood, etc.) will still be monitored. All sensors will not be able to

trigger the Warn-Away response or the Full Alarm response.

1. After disabling Warn-away response, press the

twice.

the button

2. Press the

button.

Note: The next time you arm the system, the shock sensor will work

normally.

Sensor Silent Mode

In this mode, a sensor cannot trigger the siren. All entry points (doors,

hood, etc.) will still trigger the siren.

Press the

button three times, and then press the

button.

Note: The next time you arm the system, it will function normally.

➤ Disarming the System

While the system is armed normally:

•

Press the

button once.

The siren in the vehicle will “chirp” twice, and the parking lights will

ﬂash.

If you hear four chirps on disarming, the system was triggered in your

absence. Immediately look at the Status LED in the vehicle and count

the number of ﬂashes between pauses. This number is important, it tells

what triggered your alarm. See Disarming section under Diagnostics on

page 33 for more details.

If you hear five chirps on disarming, the system was repeatedly trig-

gered in your absence. Immediately look at the Status LED in the vehicle

and count the number of ﬂashes between pauses. This number is impor-

tant, it tells what triggered your alarm.

The door locks (if connected) will unlock, and the parking lights will

ﬂash.

While the alarm is triggering:

Press the

button on the remote. The siren will stop sounding and

disarm the alarm system.

High-Security Disarming

If you want the Full Alarm response to stop without unlocking the doors,

press the

button. The system will re-arm and the current alarm re-

sponse will reset.

➤ System override

To disarm the system without a remote control:

You will need to use your Override Switch located

on your systems control center (see diagram to left)

to disarm the system. The Override Switch disarms

the system only if you have the vehicle key.

•

Open the door. The alarm will sound.

Immediately insert the key into the ignition and turn it to the RUN or ON

position. (all the indicators in the dash will turn on).

Press the Override Switch once.

Note: The Override Switch feature allows you to select a speciﬁc

number of presses needed to disarm the alarm. If the Override

Switch has been programmed to a new number of presses by your

authorized dealer, that number should be indicated below.

Override Switch Number ___________

➤ Valet mode

To enter or exit valet mode with the valet/program switch:

Turn the ignition key on and then off.

At anytime during the next 10 seconds, press and

release the Valet switch. Now the Status LED lights

constantly if you have entered Valet® Mode, and

go out if you have exited Valet Mode.

To enter or exit Valet mode with the remote control:

Press two times, and then

Mode.

to put the system into/out of Valet

Note: The LED on the control center turns on solid when in Valet Mode

and shuts off when exiting Valet Mode.

➤ Remote feature programming

The remote control has a menu for conﬁguring user features. Before you

start make sure the keypad is unlocked. (See page 13)

To program the remote user features:

1. Press and hold the

button on the remote for 12 seconds. (ig-

nore the car indicator at 3 seconds). The remote emits one long

beep, and the trasmit LED turns on to indicate the Main Menu.

2. Press and hold the

button for 1. 5 seconds: The remote beeps

two-tmes. You are now in the Remote Conﬁguration menu.

To configure the remote control features:

1. Press, and then release the command button. The remote beeps to

indicate the feature conﬁguration.

2. Press the

3. Press the

button to access the Auto keypad lock feature.

button to change the Auto keypad lock feature.

•

When the remote beeps once the keypad automatically locks

6o seconds after the last button operation to avoid accidental

command operations. When locked, if any command button is

pressed the remote emits an error tone.

•

The keypad lock feature is Off when the remote beeps twice and

the keypad does not lock.

If the keypad lock is On, press

keypad.

, and then press

to unlock the

Note: If the auto keypad lock feature is programmed On, the remote un-

locks when the vehicle ignition is turned Off. The remote stays unlocked

to allow time to exit and unload the vehicle, and then lock the doors

with the remote. When the

feature resumes normally.

button is pressed, the keypad auto lock

Remote Beeps feature

Press the

button to turn the Remote Beeps feature On and Off.

When the remote beeps once, the feature is on, the remote then beeps

when pressing any button on the remote or when programming features

on the remote.

When the remote beeps twice, the feature is off, the remote does not

beep when pressing any button on the remote but does beep when

programming features on the remote.

➤ Panic mode

If you are threatened in or near your vehicle, you can attract attention by

triggering the system with your transmitter. Just press

for 2 seconds,

and you will enter Panic Mode. The siren will sound and the parking

lights will ﬂash for the programmed siren duration. To stop Panic Mode

at any time, press

on the remote transmitter again.

Using the remote start

Read this user guide, including the Warnings section at the beginning.

Ensure that the vehicle is parked in the open air and not in a garage.

To use your remote start to pre-warm or pre-cool your vehicle, remember

to set the climate controls to the desired settings before shutting off the

engine.

➤ Remote starting your vehicle

Before using the remote start be sure the vehicle is parked in a safe

area with proper ventilation.

To remote start the vehicle:

•

Press the

button on the remote control. The vehicle parking

light ﬂashes

The preset remote start run time is 12 minutes. This can be changed to

between 12 and 60 minutes (see your authorized dealer for program-

ming changes).

Points to remember

If the hood is open or is the brake pedal is pressed, the vehicle will not

start using remote start. The remote starter shuts down:

•

When the brake pedal is pressed

The hood is opened

If the alarm is triggered when armed.

When the Remote Start command is sent again from a remote

control.

➤ Manual transmission vehicles

If the vehicle has manual transmission the proper steps must be fol-

lowed before leaving the parked vehicle or the remote start feature is

disabled.

1. Put the transmission in neutral.

2. Press on the vehicle’s foot brake.

3. Apply the emergency brake.

4. Release the vehicle’s foot brake. Note: Pressing the brake again

after this step will disable the remote start feature.

5. Within 15 seconds activate the remote start from the remote.

6. The parking lights will ﬂash 5 times conﬁrming that the remote start

is active.

7. Turn off the ignition (the car should stay running when key is turned

off).

8. Exit the vehicle and close the door.

9. Arm the alarm (the vehicle should shut off when arming the sys-

tem).

You can now remote start the vehicle. If a door is opened or if the alarm

is triggered before the next remote start activation the system will not

remote start.

To drive your vehicle after it has been remote started:

1. Get in without stepping on the brake.

2. Insert the ignition key and turn it to the ON position.

3. Now, step on the brake.

➤ Timer mode

To activate the runtime of the vehicles engine during remote start:

Important: Use Timer Mode in open areas only. Never start and run

the vehicle in an enclosed space such as a garage or carport.

To activate timer mode with an automatic transmission:

1. Remote start the vehicle by pressing twice and then press

2. The parking lights ﬂash rapidly four times.

3. After 1 second the car starts and the Timer Mode runs for the

speciﬁed time period.

To activate timer mode with a manual transmission:

1. Enter the MTS mode.

2. Exit the vehicle and arm the alarm.

3. Enter the timer mode. The parking lights quickly ﬂash 4 times to

conﬁrm entry into timer mode (vehicle does not remote start at this

point). Vehicle begins the timer mode sequence.

To exit timer mode with transmitter:

•

Press twice and then press

. Parking lights ﬂash slowly four

times conﬁrming time mode is exited.

To exit timer mode without transmitter:

1. Make sure the remote start system is not operating the engine.

2. Turn the ignition on. Timer Mode is exited and the parking lights

ﬂash slowly four times.

Timer Mode is exited automatically after the sixth run cycle. The park-

ing lights slowly ﬂash 4 times when exiting timer mode.

The same procedure may be used to enter or exit Timer Mode using

the remote transmitter.

Note: The Bitwriter can change the amount of times the remote start

activates and, it can change the intervals between activations in timer

mode.

➤ Turbo timer mode

Turbo timer mode keeps the engine running after arriving at your desti-

nation for a programmable period of 1, 3, 5 or 10 minutes. This allows

the system’s timer to conveniently cool down the turbo after you have

left the vehicle.

To activate Turbo Timer Mode with an automatic transmission:

1. Make sure the Turbo timer feature is turned on in the features

grid.

2. Open the vehicle door.

3. While the vehicle is running; press the

by the button.

button twice followed

4. The parking lights ﬂash once.

5. Turn off the ignition (car stays running).

6. Exit the vehicle and arm the system.

At this point the vehicle stays running for the programmed runtime.

To activate turbo timer mode with a manual transmission:

Perform the procedure for manual transmission vehicles (page 26), with

the door open. Transmit the timer mode feature with the remote by

pressing two-times, and then

. After exiting the vehicle, lock the

system and the vehicle remains running for the programmed runtime.

(The remote start feature is still enabled).

You can still remote start the vehicle after the turbo timer has timed out

and shut off the vehicle. For safety reasons, if a door is opened (while

the alarm is armed or disarmed) or if the alarm is triggered while you

are away, the remote start exits the manual transmission mode and

does not remote start until the MTS sequence is re-initiated.

Note: An optional push button can be hard wired to the (-) activation

input (H1/10) on the remote start. This allows the user to activate the

turbo timer without having to use the remote.

When the vehicle is running follow the procedures listed above, but

instead of pressing the remote, press the push button the appropriate

number of times to activate the remote start (factory setting is for 1

pulse). Turn off the ignition and exit the vehicle. The car remains running

for the pre-programmed amount of time.

➤ Smart start

With Smart Start you can activate remote start when the vehicle reaches

a certain temperature, or when it reaches a certain voltage.

The factory setting for temperature high is 100º, and the low is 0º (F).

The voltage setting is 10.5v. These settings can be adjusted or turned

off by your installer using the Bitwriter.

To activate Smart Start mode:

•

Press the

button.

button on the remote 3 times and then press the

The parking lights ﬂash 5 times fast to conﬁrm the remote is in Smart

Start mode.

To activate Smart Start mode with a manual transmission:

1. Enter the MTS procedure.

2. Exit the vehicle and press the

button on the remote (the vehicle

shuts down when locking).

3. Press the

button on the remote 3 times and then press the

button. The parking lights ﬂash 5 times fast to conﬁrm the remote

is in Smart Start mode.

The vehicle remote starts when the cabin temperature reaches the pro-

grammed threshold, or when the battery reaches the programmed

voltage.

Use one of the below methods to exit Smart Start mode:

•

Perform the same steps to activate Smart Start mode

Turn the ignition On to deactivate manually

Press the brake pedal

The parking lights ﬂash 5 times slowly to conﬁrm the remote has exited

Smart Start mode.

➤ Turning on the rear defogger

The rear defogger (if connected) is programmed to automatically acti-

vate when remote start is turned on. If the interior cabin temperature is

above 55˚ F the defogger will not activate.

To manually activate the rear defogger after remote start is on:

•

Press

four times, and then press

. The parking lights ﬂash 4

times to conﬁrm the defogger activation.

➤ Valet take-over

The Valet take-over feature allows the vehicle to remain running after

the key has been removed from the ignition. This feature is useful for

occasions when you wish to exit and lock the vehicle for short periods

of time, but would like to leave the motor running and the climate

controls on.

To perform Valet take-over:

1. Before turning off the engine, press and release

mitter. Then wait a few seconds.

on the trans-

2. Turn the ignition key to the OFF position (The engine will stay

running).

3. The engine will run until the pre-programmed time elapses or a

shut-down input is received.

Note: To enable Valet take-over with a manual transmission, open the

door and enter into manual transmission mode, as described above.

The parking lights ﬂash ﬁve times when entering Valet take-over. Once

you exit the vehicle you can lock the system and the car will remain

running. If the vehicle shuts down when locking, then the unit did not

enter valet take-over mode.

Safety features

This system has several important safety features to ensure proper op-

eration of the motor and prevent accidental damage to the engine or

its components.

➤ Starter anti-grind circuitry

Whenever the vehicle is remote started, advanced anti-grind circuitry

prevents the starter from engaging, even if the key is turned to the start

position. This prevents damage to the starter motor if the key is turned

to the start position during remote start operation.

Note: Anti-grind circuitry only works when the remote start system is

operating the motor and the Failsafe® Starter Kill relay is installed.

➤ Disabling the remote start system

This feature allows the remote start unit to be temporarily disabled

to prevent the vehicle from being remote started accidentally. This

feature is useful when the vehicle is being serviced or stored in an

enclosed area.

To disable the remote start, move the shutdown toggle switch to the

OFF position. Check with your installer for the location.

Location of Shutdown Switch____________________________

Diagnostics

The microprocessor at the heart of your system is constantly monitoring

all of the switches and sensors connected to it. It is designed to detect

any faulty switches and sensors and prevent them from disabling the

entire system. The microprocessor will also record and report any trig-

gers that occurred during your absence.

Refer to System Status Chirps and Table of Zones sections of this guide

for diagnostic information.

➤ Arming

If the security system is armed at the same time that an input is active

(such as a door opening or sensor triggering), you will hear one siren

chirp to indicate arming and a second siren chirp to indicate Bypass

Notiﬁcation.

A Bypass Notiﬁcation chirp means that the security system ignores

the input that was active when the system was armed, until that input

ceases. Three seconds after that input ceases, the security system will

resume normal monitoring.

For example: if your vehicle has an interior light exit delay and you arm

your security system before the interior light turns off, you may hear a

second Bypass Notiﬁcation chirp.

Once the light turns off, however, the security system resumes normal

monitoring.

Note: Bypass Notiﬁcation does not occur when the system is in Silent

Mode or if the notiﬁcation chirps have been programmed off by the

installer.

➤ Disarming

Extra chirps heard when disarming the system are the Tamper Alert.

If four chirps are heard when disarming the system, then the security

system was triggered in your absence.

If ﬁve chirps are heard when disarming the system, the system was

triggered so many times that the Nuisance Protection® Circuitry has

bypassed the intended zone. In either case, the status LED will indicate

which zone was involved (see Table of Zones).

The security system will retain this information in its memory, and chirp

four or ﬁve times each time it is disarmed, until the next time that the

ignition is turned on.

➤ System status chirps

The siren will chirp when arming/disarming the system. The pattern of

chirps will audibly report the system’s status as described below.

Action

Arm

Number of Chirps

Description

System armed

Arm

1 (3-second delay) + 1 System armed with bypass notification

Disarm

System disarmed

System disarmed with Tamper Alert

System disarmed, NPC activated

➤ Table of zones

A zone is represented by the number of LED ﬂashes used by the system

to identify a particular type of input. Standard input assignments are

listed in the following table, along with spaces to write in any optional

sensors or switches that have been installed.

Zone

Description

Dealer installed options

Trunk Pin

Instant trigger: a heavier impact

detected by the shock sensor

Door switch trigger

Instant trigger: For optional

sensors

Ignition trigger

Hood Pin

➤ Interpreting zone diagnostics

Warn Away responses are not reported by arming or disarming diag-

nostics. If you receive a Bypass notiﬁcation when arming or a Tamper

Alert notiﬁcation when disarming, look at the LED.

Active or triggered zones will be indicated by a pattern of blinks by

the LED.

For example: If zone 3 was active or triggered, the LED will blink three

times with a two-second pause. Then it will blink three times again, and

repeat until the ignition is turned on.

➤ Nuisance prevention® circuitry

Your system has Directed’s Nuisance Prevention® Circuitry (NPC). It

prevents annoying repetitive trigger sequences due to faulty door pin

switches or environmental conditions such as thunder, jackhammers,

airport noise, etc.

For example: If the alarm triggers three times within a 60-minute period

and each time the same sensor or switch triggers the alarm, NPC will

interpret those triggers as false alarms. After the third trigger, NPC ig-

nores, or bypasses, that sensor or switch (along with any other sensors

or switches sharing the same zone) for 60 minutes.

If the bypassed sensor tries to trigger the security system while it is being

bypassed, the 60-minute bypass period will start over. This ensures that

a sensor that is continually being triggered will remain bypassed.

The vehicle doors are protected by NPC differently. If your security

system is triggered by an open door for three full cycles, the system will

bypass the doors until the trigger ceases.

NPC requires that you change the way you test the system since NPC

bypasses an input zone for 60 minutes. If the system “sees” the same

zone trigger three times, and the triggers are spaced less than an hour

apart, the system bypasses that input zone for 60 minutes.

If that zone does not attempt to trigger the system during the 60-minute

bypass period, the zone’s monitoring begins again at the end of the

hour. If it does attempt to trigger while bypassed, the 60-minute bypass

starts over again.

Disarming and rearming the system does not reset NPC. The only way

to reset NPC™ is for the 60 minutes to pass without a trigger, or for

the ignition to be turned on. This allows the system to be repeatedly

triggered, disarmed and rearmed, and still allows NPC to bypass a

faulty zone.

When disarming the system, 5 chirps indicate NPC is activated. The

LED reports the zone that has been bypassed. (See Diagnostics section

of this guide.)

Owner recognition

Owner Recognition lets up to four users of the system have unique set-

tings that meet their speciﬁc needs. It is almost like having four separate

alarms in your vehicle, one for each user. This feature is only available

to authorized dealers using the Bitwriter or Bitwriter 2 program tool.

Rapid resume logic

This Directed system will store its current state to non-volatile memory.

If power is lost and then reconnected the system will recall the stored

state from memory.

For example, if the unit is in Valet Mode and the battery is disconnected

for any reason, such as servicing the car, when the battery is recon-

nected the unit will still be in Valet Mode. This applies to all states of the

system including arm, disarm, and Valet Mode.

Power saver mode

Your system will automatically enter Power Saver Mode while armed or

in Valet Mode, after a period of time in which no operation has been

performed. This lowers the current draw on the vehicle’s battery. Power

Saver Mode takes over under the following conditions:

Power Saver when the system is armed: After the system has been

armed for 24 hours the LED will ﬂash at half its normal rate, decreasing

the system’s current draw.

Power Saver in Valet Mode: When the system enters Valet Mode the

Status LED on the Responder LE control center illuminates steadily. If the

vehicle is not used (ignition is not turned on) for a one hour period while

the system is in Valet Mode, the status LED will shut off. If the system

remains in Valet Mode, the LED will come back on the next time the

ignition is turned on and then back off.

Programming options

Your system has many custom programmable options. Some may re-

quire installation labor. Ask your authorized dealer for details.

The following is a list of the programmable options, with the factory

settings in Bold.

•

Active arming (remote only) passive arming with or without locking

the doors (automatic arming without locking the doors 30 seconds

after the last door has been closed), or Auto Re-arm with or without

locking the doors (Automatically arms 60 seconds after disarm if

no door is opened).

Arming/disarming siren chirps ON with or without Warn-away chirps,

Or OFF with or without Warn-away chirps.

•

Ignition controlled door lock feature ON or OFF: When this fea-

ture is programmed on, the doors will lock three seconds after the

ignition is turned on, and unlock when the ignition is turned off.

If your installer is programming the security system with the Directed

Bitwriter®, ignition lock and unlock are independent features that can

be programmed separately.

•

Panic mode enabled/disabled when the ignition is turned on or

completely turned OFF. (Some states have laws against sirens

sounding in moving cars.)

•

Full trigger response 30 or 60 seconds: This determines how long

the full triggered sequence lasts. Some states have laws regulating

how long a security system can sound before it is considered a

nuisance.

•

If your installer is programming the security system with the Di-

rected Bitwriter®, the full triggered response can be programmed

for any duration ranging from 1 to 180 seconds.

Siren tones and chirp volume: The output of the Revenger™Soft

Chirp™ siren consists of six different tones in sequence. Any of

these tones can be eliminated by a dealer, resulting in a unique,

easily identiﬁable siren sound. The chirps can be either full volume

or 6 decibels quieter than the full alarm blast.

•

Comfort closure is a programming option which closes the ve-

hicle’s windows after remote locking.

Security & convenience expansions

Listed below are some of the many expansion options available. Please

consult your dealer for a complete explanation of all the options avail-

able to you.

Audio Sensor: Metal on glass, glass cracking, and breaking

glass produce distinctive acoustic signatures. The 506T audio sensor

uses a microphone to pick up sounds, then analyzes them with propri-

etary acoustic software to determine if the glass has been struck.

Backup Battery: The 520T keeps the system armed, triggers the alarm

and keeps the starter interrupt active if main battery is disconnected.

Digital Tilt Sensor: The 507M tilt sensor can be added to your system

to protect your car when its parked. It can protect your vehicle from be-

ing lifted and provide protection for your expensive rims.

Field Disturbance Sensor: An invisible dome of coverage is established

by installing the 508D “radar” sensor. Your system can react to any

intrusions into this ﬁeld with the full triggered sequence.

Power Locks: This system offers lock outputs that can control some manu-

facturers’ power door lock systems. For other systems, additional parts

may be required.

Power Trunk Release: The accessory output of the system can operate

a factory power release for the vehicle’s trunk or hatch. Although the

on-board relay can control most power trunk releases, sometimes an

optional relay is required. If the factory release is not power-activated,

Directed®’s 522T trunk release solenoid can often be added.

Power Window Control: Automatic power window control is provided

with the 529T and 530T systems. These can operate power windows,

and can roll them up automatically when the system is armed, roll them

down, or both up and down.

Ultrasonic Cabin Sensor: Using the 509U Ultrasonic cabin sensor pro-

vides a ﬁeld of protection inside the car to protect your belongings.

Glossary of terms

Control Center: The control center contains the system’s radio-frequency

antenna, the valet and override switch, and the Status LED.

For maximum remote-control range, the Control Center is usually lo-

cated at the top of the windshield, centered near the rear-view mirror.

Control Module: The “brain” of your system. Usually hidden underneath

the dash area of the vehicle. It houses the microprocessor which moni-

tors your vehicle and controls all of the alarm’s Functions.

Failsafe® Starter Kill (if equipped): An automatic switch controlled by

the security system which prevents the vehicle’s starter from cranking

whenever the system is armed. The vehicle is never prevented from

cranking when the system is disarmed, in Valet® Mode, or should the

starter kill switch itself fail. Your system is ready for this feature, however

installation of this feature may require additional labor.

Input: Any physical connection to the security system. An input can

be provided through a sensor, pin-switch or by existing systems in the

vehicle, such as ignition or courtesy lights.

In-vehicle status LED: A light used to indicate the status of your system.

It is located on your systems control center.

Shock Sensor: This system has a dual zone shock sensor. This sensor is

mounted in the vehicle and designed to pick up impacts to the vehicle

or glass.

Trigger or Triggered Sequence: This is what happens when the alarm

“goes off ” or “trips.” The triggered sequence of your system consists

of the siren sounding and parking lights ﬂashing for the programmed

duration.

Valet Button: A small push button switch located on your systems control

center. It is used to override the starter interrupt when a 2-way remote is

lost or damaged, or to enter or exit Valet Mode.

Warn Away® Response: Light impacts to the vehicle generate the

Warn Away® Response, which consists of several seconds of horn

honks and ﬂashing parking lights.

Zone: A zone is a separate input that the alarm can recognize as

unique. Each input to the system is connected to a particular zone.

Often, two or more inputs may share the same zone.

Quick reference guide

Arming

To arm, press . When the system arms 1 beep from the siren.

Arming while driving

To arm the system while driving, press

vehicle is running.

on your remote while the

Disarming

To disarm, press

and you will hear 2 beeps.

Disarming without a remote

Turn on the ignition. Press and release the Valet button within 15

seconds. The system should now disarm. If it does not, you may have

waited too long or pressed the button incorrect number of times.

Refer to reverse side for Valet pushes and try again.

Number of Valet button pulses for disarming_______________

Silent Arm

Press

one time and then press

Silent Disarm

Press

one time and then press

Remote Start

Press

Rear Defogger

Press

four times, and then press

(only after remote start is

ON.)

To disable the remote start system

Move the shutdown toggle switch to the OFF position.

Location of Shutdown Toggle Switch___________________

Valet Mode

Press

two times and then

Valet take over

Before turning off the engine, press and release

onds. Then wait a few seconds.

. within 3 sec-

Turn the ignition key to the OFF position.

The engine will remain running until the programmed time elapses or

a shut-down input is received.

Location of Valet button_________________________________

Notes

Limited lifetime consumer warranty

Directed Electronics. (“Directed”) promises to the original purchaser to repair or replace (at

Directed’s election) with a comparable reconditioned model any Directed unit (hereafter

the “unit”), excluding without limitation the siren, the remote transmitters, the associated

sensors and accessories, which proves to be defective in workmanship or material under

reasonable use during the lifetime of the vehicle provided the following conditions are met:

the unit was purchased from an authorized Directed dealer, the unit was professionally

installed and serviced by an authorized Directed dealer; the unit will be professionally

reinstalled in the vehicle in which it was originally installed by an authorized Directed

dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the

bill of sale or other dated proof of purchase bearing the following information: consumer’s

name, telephone number and address; the authorized dealers name, telephone number

and address; complete product description, including accessories; the year, make and

model of the vehicle; vehicle license number and vehicle identification number. All com-

ponents other than the unit, including without limitation the siren, the remote transmitters

and the associated sensors and accessories, carry a one-year warranty from the date of

purchase of the same. ALL PRODUCTS RECEIVED BY DIRECTED FOR WARRANTY REPAIR

WITHOUT PROOF OF PURCHASE WILL BE DENIED. This warranty is non-transferable

and is automatically void if: the original purchaser has not completed the warranty card

and mailed it within ten (10) days from the date of purchase to the address listed on the

card; the unit’s date code or serial number is defaced, missing or altered; the unit has been

modified or used in a manner contrary to its intended purpose; the unit has been damaged

by accident, unreasonable use, neglect, improper service, installation or other causes not

arising out of defects in materials or construction. The warranty does not cover damage

to the unit caused by installation or removal of the unit. Directed, in its sole discretion, will

determine what constitutes excessive damage and may refuse the return of any unit with

excessive damage.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING

BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF

MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON-

INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND

DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME

FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS.

DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS

OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. DIRECTED

SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE

THEFT. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST

VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS;

AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING

WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS

WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR

REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND.

IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY,

THE VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.

CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN

THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED

SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE

PRICE OF THE UNIT. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES

WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,

INCIDENTAL DAMAGES, DAMAGE TO VEHICLE, DAMAGES FOR THE LOSS OF TIME,

LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY

AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER

A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE SUBJECT TO

THE CONDITIONS AS DESCRIBED HEREIN. THIS WARRANTY IS VOID IF THE UNIT

HAS NOT BEEN PURCHASED FROM DIRECTED, OR AN AUTHORIZED DIRECTED

DEALER, OR IF THE UNIT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE,

NEGLIGENCE, ACTS OF GOD, NEGLECT, IMPROPER SERVICE, OR OTHER CAUSES

NOT ARISING OUT OF DEFECT IN MATERIALS OR CONSTRUCTION.

Some states do not allow limitations on how long an implied warranty will last or the exclu-

sion or limitation of incidental or consequential damages. This warranty gives you specific

legal rights and you may also have other rights that vary from State to State.

This warranty is only valid for sale of product(s) within the United States of America.

Product(s) sold outside of the United States of America are sold “AS-IS” and shall have NO

WARRANTY, express or implied. This product may be covered by a Guaranteed Protection

Plan (“GPP”). See your authorized Directed dealer for details of the plan or call Directed

Customer Service at 1-800-876-0800.

Make sure you have all of the following information from your authorized Directed

dealer:

A clear copy of the sales receipt, showing the following:

Date of purchase

Your full name and address

Authorized dealer’s company name and address

Type of alarm installed

Year, make, model and color of the automobile

Automobile license number

Vehicle identification number

All security options installed on automobile

Installation receipts

920-0003 06-06

The company behind this system is Directed Electronics

Since its inception, Directed Electronics has had one purpose, to provide

consumers with the ﬁnest vehicle security and car stereo products and

accessories available. The recipient of nearly 100 patents and Innovations

Awards in the ﬁeld of advanced electronic technology.

Directed is ISO 9001 registered.

Quality Directed Electronics products are sold and serviced throughout

North America and around the world.

Call (800) 274-0200 for more information about our products and services.

G5102V 2008-06

Vista, CA 92081

www.directed.com

Teledyne Oxygen Equipment 311tc User Manual
Timex Heart Rate Monitor W 248 User Manual
TOA Electronics Fire Pit B 40REN User Manual
Toshiba Cordless Telephone SX 2981 User Manual
Transcend Information Computer Drive 25C User Manual
Tyan Computer Computer Hardware I7320 User Manual
U Line Ice Maker BI 95BTP User Manual
Uniden Baby Monitor UBR243 User Manual
Vector Work Light VEC141 User Manual
VistaQuest Digital Camera VQ 7228 User Manual