A s s e m b l y
G u i d e
T9200, T9300, T9400HRT, T9500HRT,
T9600HRT, T9700HRT, & T9700S
PLATFORM TREADMILLS
TOOLS & PARTS INCLUDED
MM
8 Allen Wrench
MM
5 Allen Wrench
Screwdriver
PARTS BOX
Water Bottle, Qty: 1
Optional Heart Rate Chest Strap, Qty: 1
(T9400HRT, T9500HRT, T9600HRT,
T9700HRT, & T9700S only)
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card
HARDWARE INCLUDED
BLUE BAG
ORANGE BAG
M8 x 20L Bolts
Quantity: 2
M8 x 20L Flathead Bolts
Quantity: 4
M8 x 50L Bolts
Quantity: 4
M8 x 135L Bolts
Quantity: 4
STEP
1
ORANGE BAG
• Slide the rubber covers on to the left
& right console supports, making sure
that the lower cutout is facing inward.
• Insert one of the console supports
into the console support bracket and
secure with two bolts (M8 x 20L) in
the side of the console support
bracket.
STEP
• Insert one bolt (M8 x 20L) in the
rear of the console support bracket.
1
• Tighten all three bolts with the blue-
MM
handled 5 Allen wrench.
• Repeat this on the opposite side.
NOTE: The right console support has
a white wire tie attached to it.
5
STEP
2
BLUE BAG
MODELS T9700HRT & T9700S: Slide
the data cables down the right
console support using the white wire
tie as a guide. Make sure that the
data cable (one large ribbon cable)
goes through the large hole in the
lower part of the console upright.
MODELS T9600HRT & T9500HRT:
Slide the data cables down the right
console support using the white wire
tie as a guide. Make sure that the
data cables (1 small & 1 large
telephone style cable) go through the
large hole in the lower part of the
console upright.
STEP
2
MODELS T9400HRT, T9300
&
T9200: Slide the data cables down
the right console support using the
white wire tie as a guide. Make sure
that the data cables (1 small & 1
large telephone style cable) come out
the bottom of the right console
support.
• Mount the console to the console
mast using four bolts (M8 X 20L) and
tighten with the blue-handled
MM
5
Allen wrench.
NOTE: Push all extra data cable into
the console mast. Make sure not to
pinch or cut the data cable.
• Mount the right-hand side mount
handlebar to the console mast using
two bolts (M8 x 135L). Repeat this on
the left-hand side.
6
STEP
3
DATA CABLES
STEP
3
MODELS T9200, T9300, T9400HRT,
T9500HRT, T9600HRT: Plug in the
small data cable into the small plug
connection on the lower control
board. Plug in the large data cable
into the large plug connection on the
lower control board.
MODELS T9700HRT & T9700S: Plug
the large 20 ribbon cable into the 20
pin connection on the lower control
board. Slide down the rubber covers
on the left & right console supports.
• Install the motor cover making sure
that the rubber covers are inserted into
the motor cover. Secure the motor
cover using the six (M5 x 10L) screws.
7
STEP
4
BELT TENSION
STEP
4
• If the running belt slips when used,
MM
use the supplied 8 Allen wrench to
turn the left and right tension bolts
1
clockwise /4-turn at a time until the
belt no longer slips.
• If the running belt is too far to the
MM
right side, use the supplied 8 Allen
wrench to turn the right tension bolt
1
clockwise /4-turn at a time until the
belt remains centered during use.
If the running belt is too far to the left
side, turn the left tension bolt
1
clockwise /4-turn at a time until the
belt remains centered during use.
500 South CP Avenue
•
P.O. Box 280
•
Lake Mills. WI 53551
fax 1.920.648.3373
toll free 1.800.335.4348
•
phone 1.920.648.4090
•
2001 Vision Fitness. All Rights Reserved. 11.01 Part #Z92TM49-AG18.12PRD
AG18.12PRD
REV2
4
|