VAXCARE
Vaxcare:
AUST: 1300 36 4040
NZ: 0800 800 900
Please register your warranty. Send in your completed Warranty Card.
If you require any further assistance or advice about any
VAX please call VAXCARE on
1300 36 4040
(Australia - cost of a local call)
(NZ)
and
0800 800 900
2000 WATT
VAX Appliances (Australia) Pty Ltd
A.C.N. 009099736
296 Victoria Road Malaga Western Australia 6090.
EMAIL: [email protected]
AUST. & NZ BRANCHES
• NSW/ACT
• QUEENSLAND
Unit 2, 239 Beaconsfield St,
186 Kerry Road,
Milperra, NSW 2214
Telephone: (02) 9792 8900
Facsimile: (02) 9792 8911
Archerfield, QLD 4108
Telephone: (07) 3216 7350
Facsimile: (07) 3216 7375
• VICTORIA/TASMANIA
Unit 3, 46 Burgess Road,
Bayswater North, VIC 3153
Telephone: (03) 9761 7160
Facsimile: (03) 9761 7175
• WESTERN AUSTRALIA
296 Victoria Road,
Malaga, WA 6090
Telephone: (08) 9247 8100
Facsimile: (08) 9247 8192
Please read carefully before using your VS-03R.
Always fully extend mains cable before use.
• SOUTH AUSTRALIA/
NORTHERN TERRITORY
Unit 3, 75-77 Grange Road,
Welland, SA 5007
Telephone: (08) 8340 2222
Facsimile: (08) 8346 7933
• VAX APPLIANCES
NEW ZEALAND
27 Clemow Drive
Mt Wellington, Auckland
Telephone: (09) 5736220
Facsimile: (09) 5736224
Email: [email protected]
Download from Www.Somanuals.com. All MaInunalssStearrcuh AcndtDioownnloadM. anual
Motor Thermostat
Looking After Your Vax
IMPORTANT: The motor is equipped with a
thermal cut-out. If for any reason, the vacuum
cleaner should over-heat, the thermostat will
automatically turn the unit off. Should this
occur, unplug the vacuum cleaner from the
electrical outlet and turn the unit off. Remove
the dirt container and empty. Clean the filters.
Allow the cleaner to cool for approximately
one (1) hour. To re-start, plug into an electrical
outlet and switch back on.
IMPORTANT: The Vax VS-03R is a very powerful vacuum cleaner. It will collect an extraordinary
amount of dust and dirt, especially during the first few applications of use, which will quickly
fill a paper dust bag or block the pores of a cloth dust bag. Excessive dust and dirt will also
contaminate the motor protection and air outlet filters.
Any of these conditions usually result in a noticeable drop-off in suction, or a possible motor
shut down due to thermostat activation.
On such occasions, it will be necessary to replace the paper dust bag or wash and thoroughly dry
a cloth dust bag before reusing, and renew all filters to regain peak suction and performance.
Replacement Bags & Filters
Replacement bags and filters are available
from your Vax stockist or Vax direct. Phone
VAXCARE Service & Help
AUSTRALIA 1300 36 4040
NEW ZEALAND 0800 800 900
Any queries or concerns about using the
Vax, call VAXCARE.
Please make a note of the serial number
and model number of the appliance before
calling.
Your appliance is equipped with a dust bag. If you notice that the vacuum cleaner seems to be
less efficient than usual, check the dust indicator by selecting the maximum power and lifting
the cleaner tool off the floor. If the indicator turns red, change the bag.
To change the dustbag
Turn off the appliance and unplug it. Lift up the catch to gain access to the dustbag compartment
and raise the cover (fig.13). Pull the handle up to remove the bag holder (fig.13a). The bag can
then be unclipped and disposed of hygienically (fig.14). Do not forget to regularly change the
dust bag and filter. The efficiency of your cleaner and the life of the motor depends on it.
(Aust only: Mon-Fri. 10.00am to 6.00pm. EST)
Calls are charged at the local rate.
An answerphone is available out of these
hours.
There are over 300 approved Vax Service
Agents in Australia and New Zealand. For
the nearest Service Agent, please refer to
your Vax warranty or call VAXCARE or visit
Dustbag Indicator
When the indicator light comes on or when the suction power reduces substantially, this
indicates that you should change/empty the dust bag.
Attention: If after inserting a new dust bag, the indicator light stays on, this could be
for several reasons:
Technical Specification
Suction passages may be blocked - check flexible hose and extension tubes, suction
inlet, floor brushes and nozzles for obstruction.
•
Voltage:
Wattage:
Capacity:
Filters:
220-240V~50Hz
2000W
3.5 litres
Motor protection filter
Air outlet filter
Check motor protection filter
Check to see if air outlet filter is dirty
•
•
Check carefully which of these causes is making the light go on and correct it so that the
vacuum cleaner can work normally.
Cord length: 5 metres
Do not work the vacuum cleaner with this indicator light on, as this could cause
irreparable damage to the motor.
Weight:
Part No:
10kg
73000
Subject to technical change without notice.
6
3
Fig.5 Press the foot pedal to start the vacuum cleaner. To stop it press the pedal again.
Fig.6 Press the foot pedal to recoil the power lead. NOTE: Guide power cord with one hand.
Rewind 1-11/2 metres of cord at a time. This will prevent the cord from whipping
which could cause damage or injury.
How to Use Your Vax VS-03R
Fig.7 The hose grip has buttons for control of suction power.
Assembling the Appliance
Fig.1 The telescopic extension tubes can be lengthened by pressing the button & sliding the
inner tube to required length.
Fig.2 To attach the flexible hose to the vacuum cleaner, push the connecting end of the flexible
hose into the attachment point on the vacuum cleaner.
Fig.8 Vacuum power can be adjusted electronically by pressing one of the buttons on the
handle (fig.7).
Auto - for normal vacuuming of carpets and hardfloors.
Min - for curtains - soft furnishings.
Max - for very dirty carpets or carpet with high pile.
Using the accessories
Fig.9 Open the accessory storage compartment (fig. 9a). These accessories can be fitted
directly to the tubes or onto the end of the flexible hose handle. The small cleaning tool
is used for upholstered furniture. The crevice nozzle is ideal for cleaning awkward places
such as behind radiators, skirting boards and hard to reach areas. The brush attachment
is designed for dusting.
Adjusting the cleaning tool for carpets & hard floors
Fig.3 Hard floor position (tiles, parquet floors, etc.) - The cleaning tools brush must be in the
lower position. Press on the rocker switch to lower it.
Fig.4 Carpet or rug position - The cleaning tools brush should be raised.
Press the rocker switch to lift the brush up.
ON/OFF
MAX
MIN
AUTO
Fig.10
If you wish to pause briefly during vacuuming i.e. to move a piece of furniture or
a rug, use the special parking position on your vacuum cleaner. Slide the hook
attached to the large cleaning tool into the slot on the rear of the appliance. When
you have finished vacuuming, press pedal to stop the appliance then unplug it at
the mains. Press the pedal to automatically rewind the cord (See note fig.6).
Fig.11 & 12 You can move or store your appliance in a vertical position by sliding the hook on
extension tube into the clip on the underside of the appliance.
Getting started
Fully extend the mains cable but not beyond the yellow marker and plug it into a
standard domestic outlet
This practical system allows you to carry the vacuum cleaner around in one hand
and provides minimum storage space.
4
5
|