Instruction Manual
SUB-1200
120W 12" POWERED SUBWOOFER
CAUTION: Read this before operating your unit
CAUTION
The apparatus is not disconnected from the AC power source so long as it is connected to the
wall outlet, even if the apparatus itself is turned off. To fully insure that the apparatus is indeed
fully void if residual power, leave unit disconnected from the AC outlet for at least fifteen
seconds.
1. To ensure the finest performance, please read this manual carefully. Keep it in a safe place for future
reference.
2. Install your unit in a cool, dry, clean place – away from windows, heat sources, and too much vibration,
dust, moisture or cold. Avoid sources of hum (transformers, motors). To prevent fire or electrical shock, do
not expose to rain and water.
3. Do not operate the unit upside-down.
4. Never open the cabinet. If a foreign object drops into the set, contact your dealer.
5. Place the unit in a location with adequate air circulation. Do not interfere with its proper ventilation; this will
cause the internal temperature to rise and may result in a failure.
6. Do not use force on switches, knobs or cords. When moving the unit, first turn the unit off. Then gently
disconnect the power plug and the cords connecting to other equipment. Never pull the cord itself.
7. Do not attempt to clean the unit with chemical solvents: this might damage the finish. Use a clean,
dry cloth.
8. Be sure to read the “Troubleshooting” section on common operating errors before concluding that your unit
is faulty.
9. This unit consumes a fair amount of power even when the power switch is turned off. We recommend that
you unplug the power cord from the wall outlet if the unit is not going to be used for a long time. This will
save electricity and help prevent fire hazards. To disconnect the cord, pull it out by grasping the plug.
Never pull the cord itself.
10. To prevent lightning damage, pull out the power cord and remove the antenna cable during an electrical
storm.
11. The general digital signals may interfere with other equipment such as tuners or receivers. Move the
system farther away from such equipment if interference is observed.
12. When positioning your equipment, especially regarding speakers or other accessories, avoid positioning
them over areas where they can fall and cause injury to yourself and others.
2
Welcome….
Thank you for purchasing the SUB-1200 from VocoPro, your ultimate choice in
Karaoke entertainment! With years of experience in the music entertainment business,
VocoPro is a leading manufacturer of Karaoke equipment, and has been providing
patrons of bars, churches, schools, clubs and individual consumers the opportunity to
sound like a star with full-scale club models, in-home systems and mobile units. All our
products offer solid performance and sound reliability, and to further strengthen our
commitment to customer satisfaction, we have customer service and technical support
professionals ready to assist you with your needs. We have provided some contact
information for you below.
VocoPro
1728 Curtiss Court
La Verne, CA 91750
Toll Free: 800-678-5348
TEL: 909-593-8893
FAX: 909-593-8890
VocoPro Company Email Directory
Customer Service & General Information
Tech Support
Remember Our Website
products, packages and promo’s. And while you’re there don’t forget to check out our
Club VocoPro for Karaoke news and events, chat rooms, club directories and even a
Service directory!
We look forward to hearing you sound like a PRO, with VocoPro, your ultimate choice in
Karaoke entertainment.
FOR YOUR RECORDS
Please record the model number and serial number below, for easy reference, in case of loss or theft. These
numbers are located on the rear panel of the unit. Space is also provided for other relevant information
Model Number
Serial Number
Date of Purchase
Place of Purchase
3
Listening For A Lifetime
Selecting fine audio equipment such as the unit you’ve just purchased is only the start of
your musical enjoyment. Now it’s time to consider how you can maximize the fun and
excitement your equipment offers. VocoPro and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of your equipment by playing it
at a safe level. One that lets the sound come through loud and clear without annoying
blaring or distortion and, most importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing “comfort level” adapts to a higher volume
of sound. So what sounds “normal” can actually be loud and harmful to your hearing. Guard
against this by setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without
distortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
• Pay attention to the different levels in various recordings.
Taking a minute to do this now will help to prevent hearing damage or loss in the future.
After all, we want you listening for a lifetime.
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often undetectable until it is too late, this manufacturer
and the Electronic Industries Association’s Consumer Electronics Group recommend you
avoid prolonged exposure to excessive noise. This list of sound levels is included for your
protection.
Some common decibel ranges:
Level
Example
30
40
50
60
70
80
Quiet library, Soft whispers
Living room, Refrigerator, Bedroom away from traffic
Light traffic, Normal Conversation
Air Conditioner at 20 ft., Sewing machine
Vacuum cleaner, Hair dryer, Noisy Restaurant
Average city traffic, Garbage disposals, Alarm clock at 2 ft.
The following noises can be dangerous under constant exposure:
Level
Example
90
100
120
140
180
Subway, Motorcycle, Truck traffic, Lawn Mower
Garbage truck, Chainsaw, Pneumatics drill
Rock band concert in front of speakers
Gunshot blast, Jet plane
Rocket launching pad
-Information courtesy of the Deafness Research Foundation
4
Before Getting Started: Things to Consider
Safety
1. Power Source - Operate only from a power source as directed on the unit or in the operating instructions.
2. Polarization - If your unit is equipped with a polarized alternating current line plug (a plug having one
blade wider than the other), this plug will fit into the power outlet only one way. This is a safety feature. If
you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit,
contact an electrician to replace your obsolete outlet. Note: Do not defeat the safety purpose of the
polarized plug by trying to grind the larger metal blade down till it fits in the outlet.
3. Cord Placement - Do not allow anything to rest on, roll over, or pinch the power cord, and do not place the
power cord where it is subject to traffic and abuse. This may result in an electrical shock or fire hazard.
4. AC Outlet - Overloaded AC outlets and extension cords are dangerous as well as frayed cords and broken
plugs. Avoid compounding these situations by plugging in more appliances to such outlets. Also, try to
remove appliances with damaged cords or plugs before adding any more appliances to the area.
5. Nonuse Periods - When the unit is not used, turn the power off. When left unused for a long period of time,
the unit should be unplugged from the household AC outlet.
ITEM:
QUANTITY:
SUB-1200
AC Power Cable
Instruction Manual
(1)
(1)
(1)
Instruction
Manual
5
Installation
Installation Environment
1. Water and Moisture - Do not use this unit near water – for example near a bathtub, washbowl, swimming pool,
or the like. Damp basements should also be avoided.
2 . Condensation - Moisture may form in the unit in the following cases:
• Immediately after a heater has been turned on
• In a steamy or very humid room.
• When the unit is suddenly moved from a cold environment to a warm one If moisture forms inside this unit,
it may not operate properly. To correct this problem, turn on the power and wait about one hour to let the
moisture evaporate.
3. Heat - The unit should be situated away from heat sources such as radiators and the like. It also should not be
placed in temperatures less than 5°C (41° F) or greater that 35° C (95° F).
Installation Placement
1. Good Ventilation - Audio products are provided with ventilation openings to allow heat generated during
operation to be released accordingly. If these openings are covered or blocked, heat build-up within the unit
can cause power failure and malfunction which could also result in a fire hazard.
2. Foreign Material – Care should be taken so that objects do not fall into and liquids are not spilled into the unit.
Do not subject this unit to obsessive smoke, dust, mechanical vibration or shock.
3. Magnetism – The unit should be situated away from equipment or devices that generate strong magnetism.
4. Stacking – Do not place heavy objects, other than system components, on top of the unit.
5. Surface – Place the unit on a flat, level surface.
Maintenance
Clean the panel and controls with a soft cloth lightly moistened with mild detergent solution. Do not use any type
of abrasive pad, scouring powder or solvent such as alcohol or benzene.
Service
1. Reading Instructions - This is probably one of the most important things to remember. All the safety and
operating instructions should be read before the appliance is installed and operated. The life span of your
purchase can depend on how well you take care of it.
2. Damage Requiring Service- The unit should be serviced by qualified service personnel when:
a. The A/C power supply cord or the plug has been damaged
b. Objects have fallen or liquid has been spilled into the unit
c. The unit has been exposed to rain
d. The unit does not appear to operate normally or exhibits a marked change in performance
e. The unit has been dropped, or the enclosure damaged
3. Servicing – The user should not attempt to service the unit beyond that described in the operating instructions.
All other servicing should be referred to qualified service personnel.
6
Getting Connected
Unpacking
Prior to beginning the connection process, carefully remove the unit from its shipping box. It is recommended to
reserve the original shipping material in the event that the unit needs re-shipping. Included in the box you will find
the Sub-1200, this instruction manual and an AC power cord.
Subwoofer connections
There are a couple of methods for connecting your Sub-1200 to your audio system. One method uses MDP
speaker cables, the other method uses RCA interconnect cables. Looking at the rear panel of the Sub-1200, you
will see two sets of MDP speaker terminals, one labeled ‘HI-LEVEL IN’, the other ‘HI-LEVEL OUT’, and two sets
of RCA jacks labeled ‘LINE IN’ and 'LINE OUT'. The configuration of your existing system will determine how you
will connect the Sub-1200.
Connecting to a Dolby Digital or DTS system
All Dolby Digital and/or DTS processors have a subwoofer/LFE output. If you decide to use a subwoofer/LFE
output connection (mono) to the Sub-1200, connect an RCA-plugged patch cable from the subwoofer/LFE output
to either the "L" or "R" channels of the 'LINE IN' jacks (RCA) on the Sub-1200.
0
PHASE 180
R
L
Line In
OFF AUTO ON
POWER
CROSSOVER
FREQUENCY
LEVEL
LINE OUT LINE IN
HI LEVEL IN
HI LEVEL OUT
LEFT
RIGHT
LEFT
RIGHT
+
-
-
+
+
-
-
+
115V
230V
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
AMP/MIXER
!
FL FR SL SR C
S
LA VERNE CALIFORNIA U.S.A.
WWW.VOCOPRO.COM
Subwoofer Out
Connecting to a system with separate components
If you only have one set of pre-amp outputs on your amplifier/mixer and need to send the signal to the Sub-1200
as well as another amplifier/mixer, first send the signal to the Sub-1200 via the 'LINE IN' (RCA) jacks, and then
from the 'LINE OUT' (RCA) jacks, connect a patch cable to the 'AUDIO INPUT' jacks on your amplifier/mixer.
AMP/MIXER
AUDIO OUT
Line In
0
PHASE 180
R
L
OFF AUTO ON
POWER
CROSSOVER
FREQUENCY
LEVEL
LINE OUT LINE IN
HI LEVEL IN
HI LEVEL OUT
LEFT
RIGHT
LEFT
RIGHT
+
-
-
+
+
-
-
+
115V
230V
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
!
LA VERNE CALIFORNIA U.S.A.
WWW.VOCOPRO.COM
AMP/MIXER
AUDIO IN
Line Out
7
Getting Connected
Connecting to an amplifier with no pre-amp outputs
If no low-level Pre-Amp outputs are available, you need to run speaker cables from your main amplifier to the
Sub-1200. Run the main LEFT and RIGHT speaker cables to the Sub-1200 HI-LEVEL IN binding posts. Be sure
to double check that the polarity (-/+) on the receiver or amplifier matches the polarity on the binding posts of the
SUB-1200. Also, make sure that the outputs on your main amplifier are true ground, otherwise you would short
the output of your main amplifier. Call or email technical support if the outputs on your main amplifier do not have
true ground.
0
PHASE 180
R
L
OFF AUTO ON
POWER
CROSSOVER
FREQUENCY
LEVEL
LINE OUT LINE IN
HI LEVEL IN
HI LEVEL OUT
LEFT
RIGHT
LEFT
RIGHT
+
-
-
+
+
-
-
+
HI-LEVEL IN RIGHT
SPEAKER OUT RIGHT
115V
230V
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
AMP
!
LA VERNE CALIFORNIA U.S.A.
WWW.VOCOPRO.COM
HI-LEVEL IN LEFT
SPEAKER OUT LEFT
Connect to speakers
8
Rear Panel Descriptions and Fuctions
4
5
6
3
2
1
0
PHASE 180
R
L
OFF AUTO ON
POWER
CROSSOVER
FREQUENCY
LEVEL
LINE OUT LINE IN
HI LEVEL IN
HI LEVEL OUT
LEFT
RIGHT
LEFT
RIGHT
+
-
-
+
+
-
-
+
8
7
115V
230V
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
10
9
!
LA VERNE CALIFORNIA U.S.A.
WWW.VOCOPRO.COM
1. POWER switch – The power switch has three positions: OFF - AUTO - ON. While the OFF and ON positions
are self-explanatory, the AUTO position instructs the Sub-1200 to remain in STANDBY mode until the unit
receives an input signal.
NOTE: If the Sub-1200 unit does not receive an input signal for approximately 10 minutes, it will switch to
stand by mode until it receives a further signal.
2. PHASE SWITCH – This switch toggles the PHASE of the subwoofer with respect to the main speakers. If the
subwoofer is out of phase with the main speakers, bass response is at a reduced performance level and may
sound "weak". When all speakers are in phase, full-frequency response is at an optimal level.
(see pg.10 for more info.)
3. LEVEL – This control adjusts the subwoofers MASTER output level. Turn clockwise to INCREASE and
counter-clockwise to DECREASE level.
4. CROSSOVER – The CROSSOVER control adjusts the Sub-1200’s low-pass frequency filtering for subwoofer
output. Available low-pass settings are: 20 Hz, 40 Hz, 80 Hz and 120 Hz.(see pg.10 for more info.)
5. LINE OUT jacks – These jacks provide a LINE-LEVEL connection to external mixers/amplifiers with line level
RCA inputs.
6. LINE IN jacks – These jacks provide a LINE-LEVEL connection from external devices with line level RCA
outputs.
7. HI-LEVEL IN jacks – These MDP binding posts are for direct connection of speakers or speaker output from
an external amplifier.
NOTE: These inputs are typically used for connecting to a system that does not have "pre-out" or line level
outputs available.
8. HI-LEVEL OUT jacks – These MDP binding posts are for direct connection to main system speakers.
9. VOLTAGE SELECTOR – The VOLTAGE SELECTOR selects the amplifier to run on either 115V or 230V.
NOTES: PLEASE ENSURE THIS CONTROL IS SET CORRECTLY BEFORE PLUGGING IN AND
POWERING ON THE SUB-1200. IF THIS CONTROL IS NOT SET CORRECTLY PRIOR TO USING THE
SUB-1200, YOU MAY DAMAGE THE UNIT AND VOID YOUR WARRANTY. SELECT 115V FOR NORTH
AMERICAN BASED POWER AND 230V FOR EUROPEAN BASED POWER.
10. AC MAINS terminal – For connecting the Sub-1200 to your AC outlet.
9
Setting Up the Sub-1200
Adjusting the Crossover Setting
The Sub-1200’s built-in crossover can be used as a variable low-pass filter for customizing subwoofer output.
The available settings are 20Hz, 40Hz, 80Hz and 120Hz. If you would like the subwoofer to only output extremely
low frequencies, you would want to select a lower frequency setting i.e. 20Hz or 40Hz. If you would like the
subwoofer output to include some higher frequencies as well as low frequencies, you would want to select a
higher frequency setting i.e. 80Hz or 120Hz. Try different crossover settings to find the sound you are seeking
NOTE: The crossover setting does not affect the throughput to any external speakers that may be connected to
the HI-LEVEL IN/OUT speaker jacks.
Using the Phase Switch
Depending on the ‘absolute’ phase of your primary speakers, and relative distance of the subwoofer and primary
speakers to the listening position, the bass in the crossover region may be smoother if you reverse the phase of
the subwoofer relative to the main speakers. Try flipping the phase switch to determine which way sounds more
bass heavy. The more bass-heavy position is the setting where the output of the subwoofer and the main
speakers are most in phase. Play program materials with bass in the crossover region such as music containing
bass drums, double basses, bass guitar, etc. to determine the correct setting.
OUT OF PHASE
IN PHASE
Selecting a Volume Level
Using a test tone diagnostic of an amplifier/processor, or a diagnostic CD/DVD, set the level of the subwoofer to
well-balanced level. We recommend using an SPL meter (use "C" weighting and slow settings) for accurate signal
balancing. SPL meters can be found at Radio Shack™ and other electronics retailers. If you do not desire to use
an SPL meter or software disc for balancing, with another person, adjust the Sub-1200 level control with a listener
in the target listening area until a desired balance and sound is reached.
Subwoofer Positioning
Do Not
• Place your subwoofer directly against a wall, leave at least a minimum of 10" of space.
• Place against a radiator, panel heater or forced air-heating outlet
• Place outdoors or in a humid environment
• Plug into an AC mains outlet until all your system wiring is completed.
Position/Location
Your Sub-1200 should perform well in just about any room location. In fact, unless your ear is within a couple of
feet of the subwoofer, the bass should seem to radiate from your main speakers. We recommend setting the Sub-
1200 within 12" of a wall surface, near a corner if possible. The Sub-1200 is not magnetically shielded and
therefore should not be located too close to a television set, leave an approximate distance of at least 2-3 feet.
Failure to do so may result in your television set’s tube becoming magnetized and this will cause a distortion of
the picture, together with a change of color. No matter where you place your subwoofer, you must allow sufficient
spacing for ventilation. The rear panel has a heat sink mounted onto it and will therefore generate heat, when in
use.
10
Troubleshooting
PROBLEMS
CAUSE
SOLUTIONS
Humming or buzzing noise.
You may have a ground loop
problem.
Try using a cheater plug. Do NOT ground
the grounding tab on the cheater plug!
That would defeat the purpose of the
cheater plug for this application.
There may be a problem with
other external equipment.
Disconnect all interconnect cables from
the Sub-1200 and any external
equipment. If hum goes away when
interconnects are disconnected, hum is
coming from the rest of your equipment.
Add them back one piece at a time. The
one that causes the system to hum is the
source of the hum.
No output from the
Sub-1200 (the LED does
not light up).
AC power is not making it to
the Sub-1200.
Check that the power cord is plugged in
securely at both ends and make sure
that the power outlet the Sub-1200 is
plugged into is functioning properly.
The amplifier’s fuse is blown.
Unplug the power cord and remove the
fuse holder with a screwdriver and check
the fuse (located just above the power
plug). If the fuse is blown, replace. If the
fuse blows again, the output transistors
are probably damaged. At that point, it is
recommended to email or call technical
support for authorization to send the
Sub-1200 back for service.
Bass response sounds
"weak" or "unstable".
The Sub-1200 and main
speakers are out of phase.
Place the ‘phase’ switch in its alternate
position (0-180).
Excessive "rumbling"
sound from Sub-1200
output.
The ‘crossover’ is set too low.
Adjust the ‘crossover’ to a higher setting
i.e. 80Hz or 120Hz.
The ‘level’ control is set too
high.
Adjust the ‘level’ control to a lower
setting.
The external amplifier’s built-in
crossover, EQ or tone settings
are not balanced correctly.
Adjust the external amplifiers crossover,
EQ or tone settings
11
Glossary of Terms
Digital Echo- Digital echo is a synthetically processed sound effect that mimics natural echo. Echo in general is
the "bouncing" of waves back and forth between 2 surfaces. This effect gives a spacious or ambient feeling that
works great with vocals.
Repeat- Repeat is facet of the echo process. Repeat refers to the frequency of echoes within a period of time.
Delay- Delay is also a facet of the echo process. Delay refers to the amount of time that exists between echoes.
Vocal Cancel- Vocal Cancel is a feature that removes vocals from multiplex CD tracks. To be multiplexed, a disc
must have the vocals coded to the right channel and the music coded to the left channel. When you select Vocal
Cancel, the unit will remove the right channel (vocals) and split the left channel (music) to both sides.
Vocal Partner- Vocal Partner is a feature that removes vocals from multiplex CD tracks much in the same way as
Vocal Cancel, but with an added "auto-pilot" function. The main difference is that Vocal Partner will only remove
vocals as long as there is activity going through the microphone (singing). When you stop singing, the vocals
automatically return.
Vocal Reducer – Vocal Reducer is a feature that removes vocals from standard non-multiplex CD tracks. To do
this, the unit compares the audio on the left and right channels, and cancels out any signals that appear on both.
Most currently recorded CD’s contain the vocal layer on both sides, however some may not, leading to varying
results.
CD+G- A CD+G is a specially formatted disc that has an additional line of sub-code on the CD that is responsible
for the lyrics that play on video screen for Karaoke systems. CD+G stands for Compact Disc + Graphics.
Sub-Code – Sub-code is specially coded area of data used by CD+G manufacturers to produce lyrics for
Karaoke video output.
Multiplex (MPX)- Multiplex is a type of Karaoke software that has specially formatted left and right channels to
make multiplex features available. To be formatted for multiplex use, a disc must have the vocals coded to the
right channel and the music to the left channel. When you select a multiplex mode, the unit will remove the right
channel (vocals) and split the left channel (music) to both sides.
Rack Mountable- Rack Mountable refers to the ability to place unit into professional or travel rack cases. Such
cases are great for building complete systems and protect them during transportation. The standard rack size for
MOST cases is 19".
VCD- VCD is a disc formatted in MPEG-1. These discs are good candidates for Karaoke use as they have an
audio and a video layer to them. VCD stands for Video Compact Disc.
A/V- A/V is an abbreviation for Audio/Visual.
12
Glossary of Terms
Y-Adapter - Any type of connection that splits a signal into two parts. An example would be a connector with one
male RCA jack on one end, and two female RCA jacks on the other end.
Woofer - A speaker, (driver), used for low-frequency reproduction. Usually larger and heavier than a midrange or
tweeter.
Midrange - A speaker, (driver), used to reproduce the middle range of frequencies. A midrange is combined with
a woofer for low frequencies and a tweeter for high frequencies to form a complete, full-range system.
Tweeter – A speaker, (driver), used to reproduce the higher range of frequencies. To form a full-range system, a
tweeter needs to be combined with a woofer, (2-way system), or a woofer and midrange, (3-way system).
Pre-Amplifier - Or Pre-amp is a device that takes a source signal, such as from a turntable, tape-deck or CD
player, and passes this signal on to a power-amplifier(s). The pre-amp may have a number of controls such as
source selector switches, balance, volume and possibly tone-controls.
Out of Phase - When speakers are mounted in reverse polarity, i.e., one speaker is wired +/+ and -/- from the
amp and the other is wired +/- and -/+. Bass response will be very thin due to cancellation.
Line Level - CD players, VCRs, Laserdisc Players etc., are connected in a system at line level, usually with
shielded RCA type interconnects. Line level is before power amplification. In a system with separate pre-amp and
power-amp the pre-amp output is line level. Many surround sound decoders and receivers have line level outputs
as well.
Frequency - The range of human hearing is commonly given as 20-20,000Hz (20Hz-20kHz). One hertz (Hz)
represents one cycle per second, 20Hz represents 20 cycles per second and so on. Lower numbers are lower
frequencies
Gain - To increase in level. The function of a volume control.
Decibel (dB) - Named after Alexander Graham Bell. We perceive differences in volume level in a logarithmic
manner. Our ears become less sensitive to sound as its intensity increases. Decibels are a logarithmic scale of
relative loudness. A difference of about 1 dB is the minimum perceptible change in volume, 3 dB is a moderate
change in volume, and about 10 dB is an apparent doubling of volume. 0 dB is the threshold of hearing and 130
dB is the threshold of pain.
Cipping - Refers to a type of distortion that occurs when an amplifier is driven into an overload condition. Usually
the "clipped" waveform contains an excess of high-frequency energy. The sound becomes hard and edgy. Hard
clipping is the most frequent cause of "burned out" tweeters. Even a low-powered amplifier or receiver driven into
clipping can damage tweeters which would otherwise last virtually forever.
13
|