4
5
Counting indicator
Selected resolution
Show scanned files in microSD card
High:600 dpi / Low:300 dpi
PDSBT-ST43-VP Manual
1. Key features
5.3 Time setting
4. LED light indications
Color /Monochrome (Mono) scan selection
600/300 dpi resolution scan selection
1.
Press [TIME SET] button to enter time setting mode by using a thin, blunt object,
such as a paperclip to access the button. The LCD screen will read “1##” (step 1) for
the year. “##” is a set of numbers that would be changed to correspond to the actual
time/date setting. The numbers 1-5 in front of “##” indicates each step in the settings.
Press the [C/BW] or [DPI] buttons to select the current Year.
Built-in BLUETOOTH® wireless technology
Directly save JPEG file to microSD/microSDHC card
Supports microSD/microSDHC card up to 32GB
Driver free to download for Windows® XP, Windows® Vista™,
Windows® 7 and Mac OS® 10.4 or above
2.
3.
4.
Press
button to confirm setting. The LCD screen will now read “2##.”
Repeat steps 2 and 3 to select the Month, Date, Hour, and Minute.
(direct plug-in, driver installation not required)
Indicator
Setting
Year
Month
Date
Hour
Minute
“GREEN” SCAN LED ON
“GREEN” SCAN LED OFF
-------------------------------------------------------------------------------------------------------------
Scan in progress.
2. Functional parts
1##
2##
3##
4##
5##
Standby / Scan is complete.
“RED” ERROR LED ON
Scanning too fast.
May cause scanning error.
Restart and scan again.
When connected to USB or power adapter: Charging
5
After setting the Minute, “5##”, press the [TIME SET] button again to complete the
Time and Date setting.
“RED” ERROR LED OFF
No error in scanning speed.
Continue scanning process.
When connected to USB or power adapter: Charging
complete.
5.4 Formatting the microSD memory card
Note: All contents on the microSD card will be erased during formatting.
1.
Insert a microSD card into the scanner with metal side facing upwards. Then power
on the scanner.
Press the [FORMAT] button with a thin, blunt object, such as the end of a paperclip
to access the button. An “F” shows on the LCD screen.
-------------------------------------------------------------------------------------------------------------------------------
“BLUE” BT LED ON Bluetooth wireless technology is enabled
2.
------------------------------------------------------------------------------------------------------------------------------------------
3.
4.
Press the
button once to begin formatting microSD card.
will flash until the formatting process is complete.
﹡Scan will START when
button is pressed
button again
The SD card indicator
Part
Function
1
2
Scan LED indicator
Error LED indicator
Ready for scan: Green LED on
﹡To END scan, press
Over speed: Red LED on
Charging battery: Red LED on until complete.
5.5 Calibrating your scanner
1.
2.
3.
Clean the glass shield located on the bottom of scanner with the cleaning cloth
5. Using the scanner
3
4
LCD screen
Scanning status display
provided.
5.1 Charging the battery
BT LED indicator
Bluetooth: Blue LED on
Turn on the scanner by sliding the [POWER] switch to [SCAN] mode. Then place the
scanner on the provided “White Balance Calibration” paper.
Click and hold onto the [C/BW] button. While holding onto the [C/BW] button, press
1.
Before first using the scanner, it is recommended to charge the battery for 6-8
hours.
In power on mode, press this button to start scanning,
press this button again to stop scanning
5
Scan button
2.
To charge, connect the scanner to a (1) USB 2.0 port or (2) an outlet with the power
adapter included. When charging, “Err” (Error) red light will be lit and will turn off
once the battery is fully charged.
6
7
Battery door
For 4.2V rechargeable battery
the
button once and then release both buttons. SD card indicator
will flash and “GREEN” and “RED” LED light will turn on.
Do not move the scanner. Wait until the “RED” LED light turns off. “GREEN” LED
light will stay on.
With only the “GREEN” LED light on, start scanning the white paper by sliding the
scanner across the paper until the “GREEN” LED light turns off. (Slide the scanner
backwards if necessary).
microSD card slot
microSD/microSDHC card storage location.
4.
5.
Note: Do not remove or the battery from the battery compartment.
When Scanner is power on, press to enter Time and Date
setting mode
When Scanner is power on, press this button to format the
microSD/microSDHC card.
Bluetooth On/Off: Switch this key left to [BT] mode to
enable Bluetooth techonolgy
Power On/Off: Switch to [SCAN] mode to turn on scanner
Switch to [OFF] mode to turn off scanner.
8
9
Time set
Format button
5.2 Inserting a microSD memory card (not included)
To operate the scanner, you must insert a microSD Card (not supplied) to record and store your
pictures. Inserting the microSD memory card:
6.
Slide the [POWER] switch to [OFF] to turn off the scanner. Calibration is completed.
Power / Bluetooth
button
10
1.
2.
Turn OFF the scanner.
Insert the microSD card into the microSD card slot (with metal side facing upwards).
5.6 Setting the resolution
1.
By pressing the [DPI] resolution button on the scanner, you may choose between
11
12
USB interface
Resolution
Download photo to a computer via USB cable provided.
Gently press in until card is clicked in and latched. The SD card indicator
appear on the LCD screen.
Note: Do not force the card into the slot; forcing may damage scanner and the microSD memory
must
high resolution (600 dpi) and low resolution (300 dpi).
Select High(600dpi) / Low(300dpi) resolution;
High / Low resolution mode icon will be displayed on status
LCD screen.
2.
The high or low resolution mode will be displayed on the LCD screen to reflect your
choice.
card. Align microSD card position (as marked) and try again.
Select Color/Mono scan, Color/Mono mode icon will be
displayed on status LCD
5.7 How to scan
Note: To scan, make sure your scanner is not connected to the computer and that the [BT]
blue light is not on.
13
C/BW
1.
2.
3.
Turn on the scanner by sliding the [POWER] switch to [SCAN] mode.
Place the document on a flat surface and hold down the document with one hand.
Place the scanner on the edge of the paper approximately 5/8 to 3/4 of an inch onto
the paper to ensure the most of the document can be scanned. Make sure to keep
the scanning area in between the scanning width indicators marked on the side of
the scanner.
3. Explanation of the status icons
Item
1
Function
Description
SD card indicator
Photos will be stored in microSD card
2
3
Battery indicator
Effect indicator
Battery is full
Color or Mono
Empty battery
|