R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
2500 Series
2600 Series
FOR HOUSEHOLD USE ONLY
PARA USO CASERO SOLAMENTE
POUR UTILISATION À DES FINS
DOMESTIQUES SEULEMENT
DANGER:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Veuillez lire le manuel d’instructions et bien respecter tous les
avertissements et toutes les instructions de sécurité. Tout défaut
de le faire pourrait entraîner des blessures graves.
Electrolux Canada Corporation
6150 McLaughlin Road
Mississauga, Ontario L5R 4C2
Electrolux Home Products, Inc.
104 Warren Road
Augusta, GA 30907
Copyright E2004 Electrolux Home Products, Inc.
530163993
1/23/04
fences, or pipes, to avoid the possibility of
electric shock. Don’t handle plug or unit
with wet hands.
D Do not use with damaged cord or plug. If
unit is not working as it should, has been
dropped, damaged, left outdoors, or
dropped into water, return it to an autho-
rized service dealer for repair.
D Do not set the unit on any surface except
a clean, hard area while the unit is run-
ning. Debris such as gravel, sand, dust,
grass, etc., could be picked up by the air
intake and thrown out through the dis-
charge opening, damaging the unit, prop-
erty, or causing serious injury to bystand-
ers or operator.
D Ground Fault Circuit Interrupter (GFCI)
protection should be provided on the cir-
cuit or outlet to be used for this unit. Re-
ceptacles are available having built-in
GFCI protection and may be used for this
measure of safety.
D Keep others including children, animals,
bystanders, and helpers a minimum of 30
feet (10 meters) away. Stop the motor im-
mediately if you are approached. Do not
allow the unit to be used as a toy.
D Do not overreach or use from unstable
surfaces such as ladders, trees, steep
slopes, rooftops, etc. Use extra care
when cleaning on stairways. Keep firm
footing and balance at all times. Keeps
hands out of tubes.
D Inspect the entire unit before each use for
worn, loose, missing, or damaged parts.
Do not use until the unit is in proper work-
ing order.
D Disconnect unit from power source be-
fore servicing, cleaning, performing main-
tenance, or storing.
DOUBLE INSULATION CONSTRUC-
TION
D This unit is double insulated. See the
DOUBLE INSULATION CONSTRUCTION
section. Have all internal service per-
formed by qualified service repair person-
nel to avoid creating a hazard or voiding
your warranty.
D Have all maintenance other than the rec-
ommended procedures described in the
instruction manual performed by an au-
thorized service dealer.
D Always see an authorized service dealer
to replace a damaged impeller. Parts that
are chipped, cracked, broken, or dam-
aged in any other way can fly apart and
cause serious injury. Replace damaged
parts before using the unit.
D Never place any object in the air intake
opening as this could restrict proper air
flow and cause damage to the unit.
D Never douse the unit with water or other
liquids or squirt with a water hose. Clean
with a damp sponge and mild soap. See
STORAGE.
D Check air intake openings and tubes fre-
quently, always with the unit stopped and
power source disconnected. Keep vents
and tubes free from debris which can ac-
cumulate and restrict proper air flow.
D Do not burn, incinerate, or expose this
unit to extreme heat.
D Store the unit unplugged in a high, cool,
dry, indoor area out of the reach of chil-
dren.
D Use only recommended attachments
and replacement parts to avoid creating a
hazard and/or voiding your warranty.
D Maintain the unit according to recom-
mended procedures.
D Use only for jobs explained in this man-
ual.
Your unit is double insulated to help pro-
tectagainst electric shock. Double insula-
tion construction consists of two separate
“layers” of electrical insulation instead of
grounding. Tools and appliances built
witha double insulation system are not in-
tended to be grounded. No grounding
means is provided on this unit, nor should
a means for grounding be added to this
unit. As a result, the extension cord used
with your unit can be plugged into any
standard 120 volt electrical outlet.
Safety precautions must be observed when
operating any electrical tool. The double in-
sulation system only provides added pro-
tection against injury resulting from an inter-
nal electrical insulation failure.
WARNING: All electrical repairs to
this unit, including housing, switch, motor,
etc., must be diagnosed and repaired by
an authorized service dealer. Replace-
ment parts for
appliance must be identical to the parts
they replace. double insulated
a
double insulated
A
appliance is marked with the words
“DOUBLE INSULATION” or “DOUBLE INSU-
LATED.” The symbol (square within a
square) may also be marked on the ap-
pliance. Failure to have the unit repaired
by an authorized service dealer can
cause the double insulation construction
to become ineffective and result in seri-
ous injury.
UNIT/MAINTENANCESAFETY
D Turn off all controls and allow the motor to
stop before disconnecting the unit from
the power source.
D Disconnect the unit from the power
source when not in use. Do not leave the
unit when it is plugged into an outlet.
3
BLOWER SAFETY
D Use only in daylight or in good artificial
light.
D When using the vacuum attachment, the
unit is designed to pick up dry material
such as leaves, grass, small twigs, and
bits of paper. Do not vacuum stones,
gravel, metal, broken glass, etc., to avoid
severe damage to the impeller. To avoid
the possibility of electrical shock, do not
attempt to vacuum water or other liquids.
D Never run the unit without the proper
equipment attached. When used as a
vacuum, always install vacuum tubes
and collection bag assembly. Make
sure the collection bag assembly is
completely zipped when unit is running
to avoid flying debris. Use only recom-
mended attachments.
D Avoid situations which could set the col-
lection bag on fire. Do not vacuum dis-
carded matches, cigars, cigarettes, or
ash from fireplaces, barbecue pits, brush
piles, etc. To avoid spreading fire, do not
use blower near leaf or brush fires, fire-
places, barbecue pits, ashtrays, etc.
D Always use collection bag shoulder strap
when vacuuming to avoid loss of control.
D Check air intake openings, elbow tube,
and vacuum tubes frequently, always
with the unit stopped and the power
source disconnected. Keep vents and
tubes free of debris which can accumu-
late and restrict proper air flow. Do not
use with any opening blocked. Keep free
of dust, lint, hair and anything that may re-
duce air flow.
D Inspect the area before using the unit.
Remove all debris and hard objects such
as rocks, glass, wire, etc., that can rico-
chet, be thrown, or otherwise cause injury
or damage during operation.
D Avoid accidental starting. Be sure the
switch is in the OFF position and keep
your hand and fingers away from the
switch while connecting the unit to the
power source or when carrying a unit
connected to the power source.
D Never run the unit without the proper
equipment attached. When used as a
blower, always install a blower tube. Use
only recommended attachments. Do not
use with any opening blocked, Keep free
from dust, lint, hair and anything that may
reduce air flow.
D To avoid spreading fire, do not use blower
near leaf or brush fires, fireplaces, barbe-
cue pits, ashtrays, etc.
D Never place objects inside the blower
tubes; always direct the blowing debris
away from people, animals, glass, and
solid objects such as trees, automobiles,
walls, etc. The force of air can cause
rocks, dirt, or sticks to be thrown or to rico-
chet which can hurt people or animals,
break glass, or cause other damage.
D Never use for spreading chemicals, fertil-
izers, or any other substances which may
contain toxic materials.
STANDARDS
VACUUM SAFETY (If applicable)
D Stop the motor and disconnect the power
source before opening the air inlet door or
attempting to insert or remove the vacu-
um tubes. The motor must be stopped
and the impeller blades no longer turning
to avoid serious injury from the rotating
blades.
This product is listed by Underwriter’s Lab-
oratories, Inc., in accordance with UL Stan-
dard 1017.
If situations occur which are not covered in
this manual, use care and good judgement.
If you need assistance, contact your autho-
rized service dealer or call 1-800-554-6723.
Failure to follow all Safety Rules and Pre-
cautions can result in serious injury.
D Hard objects can be thrown through the
collection bag or the housing and be-
come dangerous missiles which can
cause sSerioAusVinjuEry toTopHeratEor oSr otEhers.INSTRUCTIONS
ASSEMBLY
WARNING: Stop the unit and dis-
connect from the power source before
opening the inlet cover or attempting to in-
sert or remove the inlet restrictor, blower
tube, nozzle, or vacuum tubes. The motor
must be stopped and the impeller blades no
longer turning to avoid serious injury from
the rotating blades.
WARNING: If you receive your
unit assembled, check each step to in-
sure your unit is properly assembled and
all fasteners are secure. Follow all safety
information in the manual and on unit.
S A standard screwdriver is required for
assembly.
4
BLOWER ASSEMBLY
3. Turn the inlet restrictor counterclock-
wise and remove it from the unit. Do not
close the inlet door. You will next attach
the vacuum tubes.
NOTE: Assembly intructions for using
your unit as a vacuum follow this section.
ATTACHING THE BLOWER TUBE AND
NOZZLE
Vacuum
Inlet Cover
1. Insert the blower tube into the blower
outlet.
2. Twist the blower tube clockwise until it
is firmly seated in the blower outlet.
3. Twist the nozzle into the end of the
blower tube until it is firmly seated.
Make sure the nozzle points upward.
Inlet
Restr
ATTACHING THE VACUUM TUBES
There are 2 vacuum tubes, an upper and
lower tube. The upper tube is cut straight on
both ends and attaches to the blower unit.
The lower tube attaches to the upper tube,
and has an angled end that you point to-
ward the ground during vacuum use.
1. Ensure unit is stopped and extension
cord is unplugged.
Blower outlet
2. Locate the arrows on the upper vacu-
um tube and on the vacuum inlet area
of the unit.
Blower Tube
Nozzle
For Model 2695 only, the blower exten-
sion tube and nozzle are combined into
one component.
Upper Vacuum Tube
Blower Tube/Nozzle
3. While holding the inlet cover open,
align the arrows and insert the vacu-
um tube into the opening. Twist the
tube clockwise until it is seated. A se-
cond arrow on the vacuum tube will
align with the arrow on the unit once
the tube is twisted completely into
place.
VACUUM ASSEMBLY
(Some models)
NOTE: Assembly instructions for using
your unit as a blower are explained in the
previous section.
If you have already assembled your unit
for use as a blower, remove the blower
tube and nozzle.
REMOVE THE INLET RESTRICTOR
An inlet restrictor is used when using your
unit as a blower. This restrictor is not used
during vacuum use and must be removed
during assembly for vacuum use.
NOTE: Be sure to keep the inlet restrictor
for using your unit as a blower.
ows on tube and unit
4. To attach thelower vacuum tube to the
upper vacuum tube, first align the ar-
rowson thetwotubes. Then, pressthe
two tubes together until the lower tube
is securely seated in the upper tube
(about 3 inches).
1. Ensure unit is stopped and extension
cord is unplugged.
2. Open the inlet cover by inserting the
tip of a screwdriver into the latch area
on the vacuum inlet cover. Gently tilt
handle of screwdriver toward the front
of the unit while pulling up on the vacu-
um inlet cover with your other hand.
r Tube
Latch Area
Vacuum Inlet Cover
Lower Tube
ATTACH THE COLLECTION BAG
Slide the opening of the collection bag
over the blower outlet. Pull the velcro
strap tightly through the buckle and se-
cure to the velcro tabs.
Impeller
5
NOTE: Make sure the velcro strap is lo-
cated on the blower outlet as shown be-
low. Also, make sure the zipper on the
bag is completely closed.
2. Remove the vacuum tubes and
collection bag.
3. Install the inlet restrictor that was re-
moved when assembling for vacuum
use.
NOTE:If you are unable to locate theinlet
restrictor, the unit will still operate. This re-
strictor improves the blower function.
4. Close the inlet cover and make sure it
is latched closed.
5. Re-install the blower tubes. Refer to
the section ATTACHING THE BLOWER
TUBE AND NOZZLE for instructions on
how to attach these items.
Velcro Strap
Collection
Bag
Blower Outlet
ADJUSTING THE SHOULDER STRAP
ON THE COLLECTION BAG
1. Carefully loop the shoulder strap
through the buckle as shown in the il-
lustration below.
SELECT AN EXTENSION CORD
Use only a 120 A.C. voltage supply as
shown on the nameplate of the unit.
S To reduce the risk of electrical shock, this
equipment has a polarized plug (one
blade is wider than the other) and will re-
quire the use of a polarized extension
cord. The appliance plug will fit into a po-
larized extension cord only one way. If
the plug does not fit fully into the exten-
sion cord, reverse the plug. If the plug still
does not fit, obtain a correct polarized ex-
tension cord. A polarized extension cord
will require the use of a polarized wall out-
let. This plug will fit into the polarized wall
outlet only one way. If plug does not fit ful-
ly into the wall outlet, reverse the plug. If it
still does not fit, contact a qualified electri-
cian to install the proper wall outlet. Do
not change the equipment plug, exten-
sion cord receptacle, or extension cord
plug in any way.
Last In
First In
2. Position the unit on your right-hand
side, blower outlet and bag pointing
toward the rear. Hold the unit in an up-
right position with the lower vacuum
tube on the ground to support it.
3. Place the shoulder strap over your
head and onto your left shoulder.
4. Adjust the strap to allow a free flow of
air from the blower. If the collection
bag is kinked, the unit will not operate
properly.
The extension cord used to reach the pow-
er source must be:
D Specifically marked as suitable for out-
door use. The cord must be marked with
the suffix “W-A” (in Canada “W”).
D Heavy enough to carry full current from
the power source to the unit. Otherwise,
loss of power and overheating can occur
causing damage to unit. Refer to table for
minimum wire gauge recommendations.
The cord must be marked with the proper
wire gauge. (Appropriate extension cords
are available.) Do not use multiple cords.
D In good condition. Cord insulation must
be intact with no cracks or deterioration.
Plug connectors must be undamaged.
DO NOT use multiple cords.
NOTE: The strap is designed to position
the collection bag on your shoulder without
kinks. The strap is not intended to support
the weight of the unit.
Shoulder strap
on left shoulder
MINIMUM A.W.G. WIRE GAUGE
RECOMMENDATIONS
No kinks in bag
allows free air flow
Amp Rating
25 ft. 50 ft.
More
Than
6
Not More
Than
10
Volts A.W.G. A.W.G.
HOW TO CONVERT UNIT FROM
VACUUM USE TO BLOWER USE
1. Stop unit and unplug the extension
cord.
120
120
18
16
16
16
10
12
6
MINIMUM A.W.G. WIRE GAUGE
RECOMMENDATIONS
USING YOUR UNIT
Amp Rating
100 ft. 150 ft.
A.W.G. A.W.G.
More
Not More
Than
10
WARNING: You MUST make sure
Volts
Than
6
the tubes are secure before using the unit.
120
120
14
14
12
12
WARNING: Do not use the unit
without the tubes or collection bag prop-
erly attached to avoid flying debris and/or
impeller contact which can cause serious
injury. Always wear eye protection to pre-
vent rocks or debris from being blown or
ricocheting into the eyes and face which
can result in blindness or serious injury.
10
12
A.W.G. = American Wire Gauge
SECURE EXTENSION CORD TO UNIT
CAUTION: Failure to use cord retainer
could result in damage to the unit, exten-
sion cord, or both.
1. Loop extension cord through cord re-
tainer.
OPERATING POSITION
Eye Protection
Eye Protection
2. Insert cord receptacle through loop.
3. Hold the cord receptacle in one hand.
Use the other hand to gently pull on
the extension cord to remove slack.
NOTE: Only remove enough slack
from the extension cord to secure it to
the cord retainer. Pulling too hard
could damage the extension cord.
4. Insert the cord receptacle into the re-
cessed plug.
Blower
Vacuum
USING YOUR UNIT AS A BLOWER
WARNING: Inspect the area be-
foreusing the unit. Remove all debris and
hard objects such as rocks, glass, wire,
etc.,that can ricochet, bethrown,orother-
wise cause injury or damage during op-
eration.
MODELS 2510 & 2525
Use your unit as a blower for:
D Sweeping debris or grass clippings from
driveways, sidewalks, patios, etc.
1
2
4
D Blowing grass clippings, straw, or leaves
into piles, or removing debris from cor-
ners, around joints, or between bricks.
Direct air flow by directing the blower tube/
nozzle down or to one side. Always work
away from solid objects such as walks,
large stones, vehicles, and fences.
Clean corners by starting in corners and
moving outward. This will help prevent an
accumulation of debris which could fly into
your face.
3
ALL OTHER MODELS
Be careful when working near plants. The
force of the air could damage tender plants.
USING YOUR UNIT AS A VACUUM
WARNING: Do not vacuum stones,
gravel, metal, broken glass, etc., to avoid
severe damage to the impeller. To avoid
the possibility of electrical shock, do not at-
tempt to vacuum water or other liquids.
Use your unit as a vacuum to pick up dry
material such as leaves, grass, small
twigs, and bits of paper.
1
2
4
3
D For best results during vacuum use, op-
erate your unit at high speed.
7
D Move slowly back and forth over the
material as you vacuum. Avoid forcing
the unit into a pile of debris as this can
clog the unit.
D Keep the vacuum tube about an inch
above the ground for best results.
D Remove the collection bag from the unit
and empty after each use. Do not store
bag without emptying the bag of all con-
tents (grass, leaves, etc.).
D Wash the bag once a year. Remove the
bag from the blower and turn the bag in-
side out. Wash the bag with a water hose.
Allow the bag to hang and dry completely
before you reuse the bag.
WARNING: If the unit becomes
clogged, stop the unit and unplug the ex-
tension cord. Wait until the impeller has
completely stopped turning, then remove
the vacuum tubes. Carefully reach into
the vacuum opening and clear out the
clogged debris.
SERVICE
HOW TO REMOVE AN OBJECT
FROM THE AIR INTAKE
WARNING: Stop the unit and dis-
connect from the power source before
opening the inlet cover. The motor must
be stopped and the impeller blades no
longer turning to avoid serious injury from
the rotating blades.
MAINTENANCE
WARNING: Disconnect power
source before performing maintenance.
S While holding the inlet cover open, re-
move the vacuum tubes. The inlet cov-
er must be held open through all re-
maining steps.
S Carefully reach into the vacuum open-
ing and clear out the air intake area.
Clear all debris from impeller.
S Inspect the impeller for cracks. If
cracked or damaged, do not use the
unit. Have parts replaced by your au-
thorized service dealer. Do not attempt
to replace them yourself.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover
items that have been subjected to operator
abuse or negligence. To receive full value
from the warranty, the operator must main-
tain unit as instructed in this manual. Vari-
ous adjustments will need to be made peri-
odically to properly maintain your unit.
BEFORE EACH USE
CHECK FOR LOOSE FASTENERS
AND PARTS
S Inlet Cover
S Blower Tube
STORAGE
S Vacuum Tubes
S Collection Bag
CHECK FOR DAMAGED OR
WARNING: Perform the following
WORN PARTS
steps after each use:
Contact an authorized service dealer for
replacement of damaged or worn parts.
S ON/OFF Switch -- Ensure switch functions
properly by moving the switch to the OFF
position. Make sure motor stops; then re-
start motor and continue.
S Inlet Cover -- Discontinue use of unit if in-
let cover fails to latch properly or if it is
damaged in any way.
S Stop unit and disconnect from the power
source.
S Allow motor to cool before storing or
transporting.
S Store unit with all guards in place. Posi-
tion unit so that any sharp object cannot
accidentally cause injury.
S Store unit unplugged, well out of the
reach of children.
AFTER EACH USE
SEASONAL STORAGE
INSPECT AND CLEAN UNIT & LABELS
Stop unit and unplug extension cord.
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit
using a damp cloth with a mild detergent.
S Wipe off unit with a clean dry cloth.
Prepare unit for storage at the end of the
season or if it will not be used for 30 days
or more.If your blower is to be stored for a
period of time:
S Stop unit and disconnect from the power
source.
S Clean the entire unit before lengthy stor-
age.
S Open inlet cover and clean any dirt,
grass, or debris that has collected. In-
spect the blower and all tubes. Close and
make sure the cover is latched.
CLEAN COLLECTION BAG
IMPORTANT: THE COLLECTION BAG
MUST BE PROPERLY EMPTIED.
D You must properly empty and maintain
the collection bag to avoid deterioration
and obstruction of air flow.
8
S Clean air vents and air inlet of debris.
S Store your unit and extension cord in a
well ventilated area and covered, if pos-
sible, to preventdustand dirtaccumula-
tion. Do not cover with plastic. Plastic
cannot breathe and may cause con-
densation and eventual rust or corro-
sion.
NEED ASSISTANCE?
Need Accessories or Assistance?
Call: 1-800-554-6723.
Need Service Parts?
Contact your dealer.
ACCESSORIES AVAILABLE
Safety Goggles Stock #952701506
S Check entire unit for loose screws. Re-
place any damaged, worn, or broken
parts.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect fromthepower source before
performing all of the recommended remedies below except remedies that re-
quire unit to be operating.
SYMPTOM CAUSE
REMEDY
1. Move switch to ON position.
2. Reconnect extension cord.
Unit fails to
operate.
1. Switch in the OFF position.
2. Extension cord discon--
nected.
3. Reset circuit breaker or
fuse.
4. Contact your authorized
service dealer.
3. Circuit breaker tripped, or
fuse blown.
4. Mechanical failure
Unit
vibrates
abnormally.
1. Contact your authorized
service dealer.
1. Mechanical failure
1. Clean unit. Remove any
debris.
2. Contact your authorized
service dealer.
Impeller will
not turn free-
ly.
1. Debris in air intake area.
2. Mechanical failure.
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS,
INC., warrants to the original purchaser
that each new Weed Eater brand electric
or cordless product is free from defects in
material and workmanship and agrees to
repair or replace under this warranty any
defective Weed Eater brand electric or
cordless product within two(2) years from
the original date of purchase.
If your Weed Eater brand electric or cord-
less product should fail within the limited
warranty period, return it, complete, pre-
paid, with proof of purchase, to the dealer
from whom it was purchased for repair or
replacement at the option of ELECTRO-
LUX HOME PRODUCTS, INC.
This warranty is not transferable and
does not cover damage or liability caused
by improper handling, improper mainte-
nance or the use ofaccessories and/orat-
tachments not specifically recommended
by ELECTROLUX HOME PRODUCTS,
INC., for this tool. Additionally, this war-
ranty does not cover parts that will wear
and require replacement with reasonable
use during the warranty period. This war-
ranty does not cover predelivery setup or
normal adjustments explained in the in-
struction manual.
THIS WARRANTY GIVES YOU SPE-
CIFIC LEGAL RIGHTS, AND YOU MAY
HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMI-
TATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS OR THE EXCLU-
SION OR LIMITATIONS OF INCIDEN-
TAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATIONS OR EX-
CLUSION MAY NOT APPLY TO YOU.
The policy of ELECTROLUX HOME
PRODUCTS, INC., is to continuously im-
prove its products. Therefore, ELEC-
TROLUX HOME PRODUCTS, INC., re-
serves the right to change, modify, or
discontinue models, designs, specifica-
tions, and accessories of all products at
any time without notice or obligation to
any purchaser.
9
|