VBP4000
VIDEO IN A BAG SYSTEM WITH
DETACHABLE 5.6" LCD MONITOR & DVD PLAYER
from falling. The “S” hooks and all straps must be fastened cor-
rectly to secure the system in the vehicle in the event of an acci-
dent. Operate the “Video in a Bag” System with the Bag open to
ensure proper ventilation of the monitor and the DVD Player. The
system is intended to be mounted for rear seat viewing only. Do
not use the system in the front seat while operating your vehicle.
3. Power
This system MUST be powered from the type of switched (Ac-
cessory) power indicated on the marking label (i.e. not directly
from the car battery). Power should be applied to the unit when
the ignition key is in the Run and/or Accessory positions. To pre-
vent battery discharge, disconnect the “Video in a Bag” System
jack from the cigarette lighter socket when the unit is not in use.
Use only the supplied power cable matching this set to avoid elec-
tric hazards. Always disconnect the power source first and then
the jack from the system.
4. Object and Liquid
Do not push objects of any kind into the system through openings;
do not spill or spray liquid of any kind on or in the system (this may
result in a fire or electric shock). Do not place anything heavy on
the unit. To ensure proper ventilation and proper operation, never
cover or block the slots and openings with a cloth or other mate-
rial.
5. Disassemble
To avoid harm from the inside laser beam to eyes, and to reduce
the risk of electric shock, do not attempt to disassemble the cabi-
net. Contact qualified service personnel if your system is in need
of repair.
6. Cleaning Unit
When cleaning, make sure the system is unplugged from the power
source. Do not use liquid cleaners or aerosol cleaners. Use a
cloth lightly dampened with water for cleaning the exterior of the
system only.
3
7. Disc
Do not use irregularly shaped discs such as heart or star-shaped
discs as they may cause the unit to malfunction. Do not stick pa-
per, tape or glue on the disc. Do not expose the disc to direct
sunlight or heat sources such as hot air ducts. Do not touch the
surface of disc. Handle the disc by its edge. Clean the disc by
wiping the disc from the center out with a cleaning cloth. Remove
the disc from the unit and store it in its case after playing. Some
playback operations of discs may be intentionally fixed by soft-
ware producers. Since this unit plays discs according to the disc
contents the software producers designed, some playback fea-
tures may not be available. Also refer to the instructions supplied
with the discs.
C. Contents
1. 1 x Detachable Monitor & DVD Player Combo
2. 1 x DIN Cable
3. 1 x AC to DC Adapter
4. 1 x Cigarette Lighter Adapter
5. 1 x Remote Control
6. 1 x Pouch
7. 1 x Travel Bag with 4 Straps
8. 1 x Instruction Manual
9. 1 x Gift Box
D. Power Source
1. Powering the system indoors (Refer to Figure 1)
Figure 1
4
Unzip the lower compartment of the bag and take out the AC to
DC adapter. Plug one end of the AC to DC adapter into the DC
12V jack on the left side of the main unit, then plug other end into
the 110V AC power receptacle.
2. Powering the system in the vehicle (Refer to Figure 2)
Figure 2
Unzip the lower compartment of the bag and take the cigarette
lighter adapter. Plug one end into the DC 12V jack on the left side
of the main unit, then plug other end into the cigarette lighter
socket.
3. Powering the detached monitor indoors (Refer to Figure 3)
Figure 3
5
The monitor can be detached from the system by depressing the
button below the screen with one hand and removing the monitor
with the other hand. Take the AC to DC adapter from the lower
compartment, plug one end into the DC 12V jack on the right side
of the monitor, then plug the other end into the 110V AC power
receptacle.
4.Powering the detached monitor in the vehicle (Refer to
Figure 4)
Figure 4
Take the cigarette lighter adapter from the lower compartment,
plug one end into the DC 12V jack on the right side of the monitor,
then plug the other end into the cigarette lighter socket.
Note:
1). When the monitor is combined with the main unit, the inside
signals including DC 12V power will be supplied from the main
unit to the monitor, so there is no need for another power source
to be connected to the DC 12V jack on the right side of the
monitor.
2). Refer to Figure 5 and 6. When the monitor is detached from
the main unit, you can connect the PORT on the right side of
the monitor to either MONITOR 1 port or MONITOR 2 port on
the left side of the main unit with the supplied DIN cable. When
the monitor is connected to the main unit with the DIN cable,
DC 12V power, Audio/Video and IR signals will all be sup-
6
plied through the DIN cable to the connected monitor. So there
is no need for another power source to be connected to the
DC 12V jack on the right side of the detached monitor.
Figure 5
Figure 6
7
E. Installation
1. Installing the system onto the seat back in a car (Refer
to Figure 7)
Figure 7
1). Unfasten the rear Velcro straps of the bag. Fold inwards the
rear piece of the bag and attach its end velcro strap to the
middle Velcro strap on the back of the bag to form a triangle.
2). Hang the bag onto the seat back by looping the shoulder strap
of the bag around the headrest of the seat.
3). Take one of the supplied straps from the lower compartment
of the bag, and connect the latch to the lower metal ring on the
left side of the bag. Attach the "S" hook to the same ring after
looping the strap around the driver's seat rail. Repeat this pro-
cess for the right side. In some vehicles, it may be necessary
to attach the "S" connector to the rail directly, as it may not be
long enough to reach back to the ring.
4). Adjust the straps tightly so that the bag is secured.
5). Unzip the bag and flip down the front flap. Ensure the inside
Velcro straps of the bag is fastened to prevent the unit from
falling. Swing the monitor upwards and adjust the screen for
the desired viewing angle.
8
2. Installing the system between the driver/passenger seat
(Refer to Figure 8)
Figure 8
1).Take one of the supplied straps from the lower compartment
of the bag, and connect the latch to the upper metal ring on the
left side of the bag. Attach the "S" hook to the same ring after
looping the strap around the headrest of the driver's seat. Re-
peat this process for the right side (Passenger Seat).
2).Take another strap and connect the latch to lower metal ring on
the left side of the bag. Attach the "S" hook to the same ring
after looping the strap around the driver's seat rail. Repeat
this process for the right side. In some vehicles, it may be nec-
essary to attach the "S" connector to the rail directly, as it may
not be long enough to reach back to the ring.
3). Adjust the straps tightly so that the bag is secured.
4). Unzip the bag and flip down the front flap. Ensure the inside
Velcro strap of the bag is fastened to prevent the unit from
falling. Swing the monitor upwards and adjust the screen for
the desired viewing angle.
9
3. Installing the system on the back seat in a car (Refer to
Figure 9)
There is no need to remove the four straps from the bag as they
are not used in this installation.
Figure 9
Carefully place the system (front facing up) on the back seat. Guide
the vehicles safety belt through the short strap sewn on the back
of the bag. Then secure and adjust the safety belt so that the sys-
tem is not free to move around. Finally uncover the bag, swing
the monitor upward and adjust the screen for a desired viewing
angle. Ensure the inside Velcro strap of the bag is fastened to
prevent the unit from falling.
4. Installing the detached monitor onto the seat back in a car
(Refer to Figure 10)
Figure 10
10
1). Follow the installation instruction shown in Item 1, 2 or 3.
2). Detach the monitor from the main unit by depressing the but
ton below the screen with one hand and remove the monitor
with the other hand. Take the pouch from the rear compartment
of the bag. Slide the monitor into the pouch, and make sure to
feed the bottom piece of the pouch into the long slot at the
bottom of the monitor and attach the Velcro strap to fasten the
monitor in the pouch. Then loop the strap of the pouch around
the headrest and pull the end of the strap while holding the
buckle until the pouch is tightly secured.
3). Insert one end of the DIN cable into the PORT on the right side
of the detached monitor, and the other end into either MONI-
TOR 1 port or MONITOR 2 port on the left side of the main unit.
5. Placing the system in a hotel/office/home (Refer to
Figure 11)
Figure 11
1). Just place the system on a table or other level surface with the
system bottom facing down. Uncover the monitor and adjust
the screen for the desired viewing angle. This can be done
with or without the unit inside its bag. You can remove the main
unit from the bag by unfastening the inside Velcro strap of the
bag.
11
2). You can detach the monitor from the main unit by depress
ing the button below the screen with one hand and removing
the monitor with the other hand. Rotate the base of the monitor
backward so that it may be placed on a table or other level
surface. Adjust the screen for the proper viewing angle. This
can be done with or without the monitor inside its pouch. Insert
one end of the DIN cable into the PORT on the right side of the
detached monitor, and the other end into either MONITOR 1 or
MONITOR 2 port on the left side of the main unit.
F. Controls, Indicators, and Connectors
1. Unit View (Refer to Figure 12)
31
Figure 12
12
1). Brightness Up/Down Thumbwheel
2). Volume Up/Down Thumbwheel
3). Headphone Input Jack # 2
4). Headphone Input Jack # 1
5). S Video Output Jack
6). DVD Video Output Jack
7). DVD Audio L Output Jack
8). DVD Audio R Output Jack
9). Monitor Port # 1 (Output)
10). Monitor Port # 2 (Output)
11). DC 12V Input Jack for Main Unit
12). Video Input Jack for Main Unit
13). Audio L Input Jack for Main Unit
14). Audio R Input Jack for Main Unit
15). Power LED Indicator for Monitor
16). Power Button for Main Unit
17). DVD Menu Button
18). Up/Down/Left/Right/Enter Buttons
19). Previous Button
20). Play Button
21). Next Button
22). Stop Button
23). Eject Button
24). Remote Control Sensor
25). Power On/Off Button for Monitor
26). Audio R Input Jack for Monitor
27). Audio L Input Jack for Monitor
28). Video Input Jack for Monitor
29). Monitor Port (Input)
30). DC 12V Input Jack for Monitor
31). DVD Slot
13
2. Remote Control View (Refer to Figure 13)
1). Power Button
2).Display Button
EJECT
3). Angle Button
4). Subtitle Button
5). Audio Button
6) Zoom Button
7). Up/Down/Left/Right/Enter Buttons
8). Menu Button
9). Return Button
10). A-B Button
11). Slow Button
12). Pause Button
13) Stop Button
14. Eject Button
15). Number Buttons
16). Setup Button
17). Repeat Button
18). Previous Button
19). Next Button
20). Reverse Button
21). Forward Button
22). Play Button
Figure 13
G. Playing A DVD
After connecting power to the unit, press the power button on the
main unit momentarily and press the power button on the side of
the monitor. Insert the disc into the slot on the right side of the
main unit, the unit will load the disc and start playing automati-
cally; if there’s a disc inside unit, press the POWER button, the
unit will start playing automatically.
14
1. Basic Operation
POWER
OPEN/CLOSE
PLAY
Turn on/off the unit
Eject/load the disc
Start Play
SLOW
PAUSE
STOP
Play at 1/2, 1/4, or 1/8 times speed
Still Picture
(1 time) Stop at the present playing point / (2
times) Stop playing
NEXT
Go to the next chapter, track or scene during
play back
PREVIOUS
Go back to the preceding chapter, track or
scene during play back
FORWARD
REVERSE
UP/DOWN/LEFT
/RIGHT
Scan forward at 2, 4, 6, or 8 times speed
Scan backward at 2, 4, 6, or 8 times speed
Used for Menu Navigation
ENTER
Execute item or setting
NUMBERS
Return
MENU
REPEAT
A-B
Select item or setting
Return to the previous selection
Display the root menu of the disc
Repeat playing title or chapter
Repeat a specific portion from point to point B
of the disc
DISPLAY
Display information (title, chapter, track, time,
etc.).
ANGLE
SUBTITLE
AUDIO
Change the angles on the scene
Select the subtitle language and turn it on/off
Select the audio language and listen
Enlarge an image to 1.5, 2, or 4 times the
original
ZOOM
SETUP
Display the setup menu to select and set items,
and exit the setup menu.
15
2. Menu
A DVD is divided into sections called title and chapter. When you
play a DVD, a root menu of the disc will appear on the screen of
your TV or Monitor. The contents of the menu vary from disc to
disc. Press MENU during playing to display the menu, and press
ENTER or PLAY to start playing. Some DVDs allow you to select
disc play back options using the DVD menu.
3. Display (The contents vary from disc to disc.)
1). Playing time and remaining time
a. During play back press DISPLAY to display the current title
number (1), the total number of titles (2), the current chapter
number (3), the total number of chapters (4), and the playing
time for the title (5). The heading will disappear automatically
in about 3 seconds.
(Menu 1)
b. Press DISPLAY again to display the remaining time for the
title. The heading will disappear automatically in about 3 sec-
onds.
16
(Menu 2)
c. Press DISPLAY the 3rd time to display the elapsed time for
the chapter. The heading will disappear automatically in about
3 seconds.
(Menu 3)
Press DISPLAY the 4th time to display the remaining time for
the chapter. The heading will disappear automatically in about
3 seconds.
(Menu 4)
Press DISPLAY the 5th time to exit.
17
2). Angle
During play back press ANGLE to view angles for discs con-
taining multi-angles, with the current angle number (1) and the
total number of angles (2) displaying. Go on to press ANGLE
to select other angle, and finally exit to return to normal viewing
angle. The angle display will disappear automatically if the
ANGLE button isn’t pressed again in about 3 seconds.
(Menu 5)
3). Subtitle
During playing press SUBTITLE to select the subtitle language
you desire, with the current subtitle language number (1) and
the total number of subtitle languages (2) displayed. If there
are multiple languages press SUBTITLE again to select an-
other subtitle language. To turn subtitles off, press the subtitle
button until SUBTITLE OFF is displayed. The subtitle display
will disappear automatically if the SUBTITLE button isn’t
pressed again for 3 seconds.
(Menu 6)
18
4). Audio
During play back press AUDIO to select the audio language
you desire, with the current audio channel number (1) and the
total number of audio channels (2) displayed. Press AUDIO
again to select another audio language. The audio display will
disappear automatically if the AUDIO button isn’t pressed again
for 3 seconds.
(Menu 7)
5). Zoom
During play back press ZOOM to enlarge the picture by 1.5, 2,
or 4X with the current zoom multiple (1) displaying. Press Up/
Down/Left/Right to move the zoomed picture. Press ZOOM
again to select other zoom multiple or until ZOOM OFF is dis-
played and the picture will return to normal size. The zoom dis-
play will disappear automatically if the ZOOM button isn’t
pressed again for 3 seconds.
(Menu 8)
19
6). A-B Repeat
a. During play back press A-B to set the starting point A.
(Menu 9)
b. Press A-B to set the ending point B and the player will re-
peatedly play the part between Point A and Point B.
(Menu 10)
c. Press A-B a 3rd time to cancel A-B repeat. Normal play back
will resume from Point A.
(Menu 11)
20
7). Repeat
a. During play back press REPEAT to repeatedly play the cur-
rent chapter.
(Menu 12)
b. During play back press REPEAT again to repeatedly play the
current title.
(Menu 13)
3. During play back press REPEAT a 3rd time to cancel the re-
peated playing and resume normal play back. The repeat dis-
play will disappear automatically if the REPEAT button isn’t
pressed again for 3 seconds.
(Menu 14)
21
4. Setup (The contents vary from disc to disc.)
Press SETUP to display the main page of the setup menu on the
screen. Press SETUP again to exit the SET UP menu and the
unit will resume last play back or stop mode.
(Menu 15)
1). Select GENERAL SETUP using UP/DOWN, and then press
ENTER to enter the general page.
(Menu 16)
a. Select TV DISPLAY using UP/DOWN, and then press RIGHT
to enter the submenu. Select the TV display mode on the
screen using UP/DOWN, and press ENTER to confirm the
setting. Press LEFT to return.
* NORMAL/PS: When the player is connected to a normal
TV, and a wide picture is shown on the full screen, with a
portion may be cut off automatically.
* NORMAL/LB: When the player is connected to a normal
TV, and a wide picture is shown on the screen, with black
strip at both top and bottom of the screen.
* WIDE: When the player is connected to a wide screen TV,
a wide picture is shown on the full screen.
22
b. Select TV TYPE using UP/DOWN, and then press RIGHT to
enter the submenu.
(Menu 17)
Select the video system on the screen using UP/DOWN, and
press ENTER to confirm the setting. Press LEFT to return.
* MULTI: The connected TV is multi system.
* NTSC: The connected TV is NTSC system.
* PAL: The connected TV is PAL system.
c. Select ANGLE MARK using UP/DOWN, and then press RIGHT
to enter the submenu. Choose if to show angle mark on the
screen using UP/DOWN and then press ENTER to confirm the
setting. Press LEFT to return.
(Menu 18)
* ON: The screen will show angle mark. (If angle option is avail
able)
* OFF: the screen won’t show angle mark.
23
d. Select MAIN PAGE using UP/DOWN, and then press ENTER
to return to the main page.
(Menu 19)
2). When there’s no disc inside the player, select PREFERENCES
using UP/DOWN, and then press ENTER to enter the prefer-
ences page.
(Menu 20)
a. Select AUDIO using UP/DOWN, and then press RIGHT to en
ter the submenu. Select the audio language you desire using
UP/DOWN, and then press ENTER to confirm the setting. Press
LEFT to return.
b. Select SUBTITLE using UP/DOWN, and then press RIGHT to
enter the submenu. Select the subtitle language or SUBTITLE
OFF you desired using UP/DOWN, and then press ENTER to
confirm the setting. Press LEFT to return.
24
(Menu 21)
c. Select DISC MENU using UP/DOWN, and then press RIGHT
to enter the submenu. Select the disc menu language you de-
sire using UP/DOWN, and then press ENTER to confirm the
setting. Press LEFT to return.
(Menu 22)
Note: Language selection is only available for discs recorded
in above listed languages. If not, the player will play and display
on the screen the original recorded language contained in the
disc.
d. Select PARENTAL using UP/DOWN, and then press RIGHT to
enter the submenu.
(Menu 23)
25
Select the parental level you desired using UP/DOWN for discs
with lock-out function or multiple rating levels. It’s listed from
the lowest level (1 Child) to the highest level (8 Adult). Press
ENTER to enter the password verify page.
(Menu 24)
Input the password in 4 digits, and then press ENTER to con-
firm the parental level setting. NOTE: for 1st time use, the de-
fault password 3308.
e. Select PASSWORD using UP/DOWN, and then press RIGHT
to enter the submenu.
(Menu 25)
Press ENTER to enter the password change page. Input the
old password or the default password, the new password, and
the confirmed new password. Press ENTER to confirm the
change.
(Menu 26)
26
Note: The default password is 3308 and this password is al-
ways effective whether you’ve changed it to another new one
or not, in case that you forget the new password. To avoid oth-
ers using it to set the parental level and change the password,
you may note this default password by other means and delete
it from this manual. Some discs can be limited depending on
the age of users while some discs can not.
f. Select DEFAULTS using UP/DOWN, and then press RIGHT to
enter the submenu. Press ENTER to make the setting re
turn to the factory-set mode.
(Menu 27)
g. Select MAIN PAGE using UP/DOWN, and then press ENTER
to return to the main page. Press SETUP to exit the MAIN
PAGE
(Menu 28)
27
H. Playing a Video Game (Refer to Figure 14)
Figure 14
1.Plugthevideooutputfromyourgamesystemintotheyellowvideo
jack and the Audio L and Audio R into the applicable jacks on the
left side of the main unit, which takes priority to the built-in DVD
Player.Adjustthevolumecontrolandthebrightnesscontrolonthe
monitorforindividualpreference.
2.Plugthevideooutputfromyourgamesystemintotheyellowvideo
jack and the Audio L and Audio R into the applicable jacks on the
rightsideofthemonitor,whichtakespriorityoverbothAVinputinto
themainunitandthebuilt-inDVDPlayer.Adjustthevolumecontrol
andthebrightnesscontrolonthemonitorforindividualpreference.
28
I. Wired Headphone (Refer to Figure 14)
Optional wiredheadphonesmaybeusedwiththe"VideoInaBag"
System. Simply plug in the headset to either headphone 1 or 2
jackontheleftsideofthemonitor. NOTE:Usingheadphonejack
#1 will disconnect the internal speakers.
J. Support Monitors
1. Using MONITOR PORT (Refer to Figure 14 and Figure 15)
Besidesthemonitorcombinedwiththemainunit,thissystemcan
drive up to 2 additional monitors (Please contact an Audiovox
dealer for the additional monitors) by using the cigarette lighter
adapter in the vehicle. (NOTE: The AC adapter can drive only 1
main unit and 1 monitor either combined or detached). Connect
the PORT on the additional monitor to either MONITOR 1 port or
MONITOR2portontheleftsideofthemainunitwiththesupplied
DINcable. Afterplugginginthemainunit, DC12Vpower, Audio/
Video and IR signals will all be supplied through DIN cable to the
additionalmonitor.
Figure 15
29
2.UsingVIDEO,AUDIOL,AUDIORoutputs(RefertoFigure14)
Matchthecolor-codedplugstotheappropriateDVDOUTjackson
theleftsideofthemainunit:Yellow(Video)toYellow,White(Audio
L) to White, and Red (Audio R) to Red.
3. Using S VIDEO output (Refer to Figure 14)
Connect the S VIDEO jack on the left side of the main unit to the
S VIDEO connector on your TV for a high quality picture.
K. Specification
Disc format: DVD/CD
Color system: NTSC
Screen size”: 5.6”
DVD video format: Horizontal 720 pixel, vertical 480 pixel (NTSC)
Frequency response:DVD (PCM 96 kHz/24 bits ): 20 Hz to 44 kHz
DVD (PCM 48 kHz): 20 Hz to 22 kHz
CD: 20 Hz to 20 kHz
Video output: 1.0 Vp-p/75 Ohm, unbalanced
Video S/N: Better than 35 dB
Audio output: 2 x 1 W
Audio S/N: Better than 35 dB
Power source: DC 11 V to 16 V
Power consumption: 35 W
Operating temperature: 5~40°C (41~104°F)
Storage temperature: -20~60°C (-4~140°F)
Operating humidity: 10~75%
Dimensions (W x H x D): 310 x 350 x 186 mm (12.2” x 13.8” x 7.3”)
30
90 DAY LIMITED WARRANTY
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser
of this product that should this product or any part thereof, under normal use and
conditions, be proven defective in material or workmanship within 90 days from the
date of original purchase, such defect(s) will be repaired or replaced with new or
reconditioned product (at the Company's option) without charge for parts and repair
labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be
delivered with proof of warranty coverage (e.g. dated bill of sale), specification of
defect(s), transportation prepaid, to the warranty center at the address shown below.
This Warranty does not extend to the elimination of car static or motor noise, to
correction of antenna problems, to costs incurred for installation, removal, or
reinstallation of the product, or damage to tapes, compact discs, speakers, acces-
sories, or vehicle electrical systems.
This Warranty does not apply to any product or part thereof which, in the opinion of
the Company, has suffered or been damaged through alteration, improper installation,
mishandling, misuse, neglect, accident, or by removal or defacement of the factory
serial number/bar code label(s). THE EXTENT OF THE COMPANY'S LIABILITY
UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PRO-
VIDEDABOVEAND,INNOEVENT,SHALL THE COMPANY'S LIABILITY EXCEED
THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY,
SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY
ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IM-
PLIEDWARRANTYOFMERCHANTABILITYMUSTBEBROUGHTWITHINAPERIOD
OF30MONTHSFROMDATEOFORIGINALPURCHASE. INNOCASESHALLTHE
COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED,
WHATSOEVER. No person or representative is authorized to assume for the
Company any liability other than expressed herein in connection with the sale of this
product.
Some states do not allow limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential damage so the above limita-
tions or exclusions may not apply to you. This Warranty gives you specific legal rights
and you may also have other rights which vary from state to state.
U.S.A.: AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 l 1-800-645-9944
CANADA: CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA
7
FormNo.128-5047A
© 2002 Audiovox Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788
128-6291
31
For Custom er Service
Visit O ur W ebsite At
WWW.audiovox.com
Product Inform ation, Photos,
FA Q ’s O wner’s M anuals
© 2002 Audiovox Electronics Corp., Hauppauge, NY 11788
128-6291
|