XIA3145
INSTALLATION/OWNER’S MANUAL
2/1-Channel Mobile Power Amplifier
XIA3145 INSTALLATION
Connection Descriptions
NOTE: Be sure to follow specific instructions included with your amplifier installation
kit (not included with this amplifier). The information below should be used a general
guideline only.
Power Wire (+12V)
• Disconnect negative battery terminal before proceeding. Consult a qualified
technician for instructions if you are unsure.
• Plan wire routing before cutting any wires to length. Begin by routing the power
+12V wire from the battery to the amplifier location. Use a grommet when running
wires through the firewall or metal openings. Avoid running the power wire near
existing vehicle wiring to prevent induced noise from entering the audio system.
• Use extreme caution when drilling holes to avoid damaging fuel lines or existing
vehicle wiring.
• The +12V wire MUST be fused within 18" of the battery for protection of the vehicle’s
electrical system.
Ground Wire (GND)
• The amplifier ground wire should be as short as possible. Choose a clean unpainted
section of metal or the vehicle chassis when attaching the ground connection.
Be sure to clean the area of any dirt or grease.
Remote Turn-on Wire (REM)
• The remote turn-on wire connects to the head unit's amplifier turn-on lead or
power antenna output.
Speaker Wires
• Choose adequate gauge speaker wire depending on your exact amplifier/speaker
combination. Be sure to observe polarity when connecting.
• Do not ground any speaker wires or connect any speaker wires together.
Illuminite Circuit (12VDC Output - for DUAL illuminite speakers only)
• Use 18-gauge or larger wire for making the connections to the illuminite terminals
of DUAL illuminite speakers ONLY. Be sure to observe polarity when connecting.
• Do not ground any illuminite output wires or connect any illuminite wires together.
Input Signal
• The amplifier's input signal connects to the head unit's low level (RCA) or high level
(speaker wire) outputs.
• Low level input signal deliver the best performance. If unavailable, use the high
level inputs - when interfacing with factory head unit for instance.
CAUTION
• Do not use both low and high level inputs at the same time - connect only one or
the other.
3
XIA3145 INSTALLATION
Connections and Controls
1
2
3
4
5
6
7
14
13
12
11
10
9
8
Ground Connection
Remote Connection
+12VDC Battery Connection
Main Fuses
Low Level Inputs
High Level Inputs
Input Level Control
Crossover Frequency
Crossover Mode Switch
Bass Boost
1
2
3
4
5
6
7
8
9
10
11
12
13
14
illuminite Fuse
Illuminite Outputs
Speaker Connections
LED Indicator
4
XIA3145 INSTALLATION
Typical Wire Routing
Main Power Connections
Connect +12V, GND and REM wires accordingly. A suitable fuse MUST be installed on the
+12V lead within 18" of the battery for protection of the vehicle’s electrical system.
Fuse Rating
Power/Ground Wire Size
When replacing fuses, make sure
new fuse is the correct type and
amperage. Using an incorrect fuse
could damage the amplifier.
For optimum performance, use only
the wire size listed below or larger.
Make sure to use the same size
power and ground wire.
Main fuse 20 amp ATO x 2
Power/ground 8 gauge
illuminite fuse 2 amp ATO x 1
illuminite output 18 gauge
5
XIA3145 INSTALLATION
Output Connections
The lighting elements of DUAL illuminite speakers provide you with a unique custom
touch to your vehicle. Dual’s patent pending illuminite LED system and control circuitry
provides an extraordinary blue-hue illumination which allows great creative opportunities
for the beginner and seasoned custom installer alike. DUAL XIA-series amplifiers provide
a dedicated switched 12VDC output including independent fused protection (2 amp)
specifically for use with illuminite speakers.
DUAL illuminite speakers have two distinct sets of input terminals. The first is labeled
audio input terminals and the second is labeled illuminite lighting inputs. The inputs are
clearly marked with a label positioned directly above the terminal housing. The polarity
(+ and -) indicators for each set of inputs also appear on these labels.
1. Do not connect the amplifier speaker outputs or any audio source to the illuminite
lighting inputs.
2. Refer to the figures below for making the connections. Make sure to observe polarity
as the illuminite circuitry will not operate when connected reverse polarity. Connect
either red wire from the XIA amplifier illuminite outputs to the positive (+) illuminite input
terminal and connect either black wire from the XIA amplifier illuminite outputs to the
negative (-) illuminite input.
Additional illuminite wiring notes:
Several illuminite speakers can be connected to the 12VDC illuminite output at one time.
Refer to the table below for the individual illuminite speaker current requirements.
If you are unsure, consult a qualified professional or call DUAL technical assistance at
1-866-382-5476 for further information.
illuminite current
requirements
(per speaker)
XiNC112 - 55mA
XiNC110 - 55mA
XiNBP210 - 180mA
XiNBP212 - 180mA
OUTPUT CONNECTOR
(Plugs into amplifier)
6
XIA3145 INSTALLATION
Amplifier Connections
2 Speakers (stereo)
Subwoofer (mono)
Speaker Connections
Connect speaker wires observing
polarity. The minimum impedance
load is 2 ohms stereo and 4 ohms
bridged. Use of loads lower than
these is not recommended and
may cause amplifier damage.
The XIA3145 can be wired for
stereo, bridged or stereo/bridged
simultaneous operation.
Typical Stereo Wiring
Typical Bridged Wiring
(2 ohms minimum)
(4 ohms minimum)
Input Signal Connections
Low Level Input (RCA)
Low level (RCA) input signal is preferred for best performance. Typical trunk-mount
amplifier installations require a 17-20 foot RCA cable. Most trucks and under-seat
applications require a 6-9 foot RCA cable. Using twisted pair construction RCA cables will
minimize noise.
High Level Input (Speaker Wire)
High level inputs should only be used
when RCA outputs are not available
from the head unit. Connect the head
unit speaker outputs to the high level
input connector as shown below. The
black wire (signal reference ground)
may or may not require a connection
to chassis ground - depending on your
particular installation.
CAUTION: Do not use both low and high
level inputs at the same time - connect
only one or the other.
7
XIA3145 OPERATION
Configuration/Setup
Input level Control The input level control (gain) is used to obtain the best
possible match between the head unit audio output and
the amplifier input. Begin by turning the input level control
fully counterclockwise. Next, turn up the head unit volume
control around 3/4 of the way up. Adjust the input level
control clockwise until audible distortion is heard, then
slightly counterclockwise to provide the best match.
Crossover Mode The crossover is used to filter out frequencies above or
below a certain point. Choose LPF when using the amplifier
with subwoofers, HPF when using with midrange/tweeter
combinations and FULL when using with coaxial-type
speakers.
NOTE:
Choose FULL when using the amplifier in stereo/bridged
simultaneous mode. In this mode, passive crossovers are
required. Failure to use the correct passive components
may damage the amplifier and/or speakers. Consult a
qualified professional for recommendations.
Crossover Frequency Control This control allows precise adjustment of the crossover
frequency.
Bass Boost This control provides additional boost @ 45Hz when used
with subwoofers. Adjust this control with caution - as
improper use can damage speakers!
LED Indicator The LED indicator illuminates green during normal
operation (POWER) and red when the amplifier detects a
fault (PROTECT).
8
XIA3145 WARRANTY
Limited One Year Warranty
This warranty gives you specific legal rights.
What to do?
You may also have other rights which vary from
state to state.
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any custom
controls may save you a service call.
Dual Electronics Corp. warrants this product to
the original purchaser to be free from defects in
material and workmanship for a period of one
year from the date of the original purchase.
2. If you require service during the warranty
period, you must carefully pack the product
(preferably in the original package) and ship
it by prepaid transportation with a copy of the
original receipt from the retailer to an
authorized service center.
Dual Electronics Corp. agrees, at our option,
during the warranty period, to repair any defect
in material or workmanship or to furnish an
equal new, renewed or comparable product
(whichever is deemed necessary) in exchange
without charges, subject to verification of the
defect or malfunction and proof of the date of
purchase. Subsequent replacement products
are warranted for the balance of the original
warranty period.
3. Please describe your problem in writing and
include your name, a return UPS shipping
address (P.O. Box not acceptable), and a
daytime phone number with your shipment.
4. For more information and for the location of
the nearest authorized service center please
contact us by one of the following methods:
Who is covered? This warranty is extended to
the original retail purchaser for products
purchased and used in the U.S.A.
• Call us toll-free at 1-866-382-5476
• E-mail us at [email protected]
What is covered? This warranty covers all
defects in material and workmanship in this
product. The following are not covered:
installation/removal costs, damage resulting
from accident, misuse, abuse, neglect, product
modification, improper installation, incorrect
line voltage, unauthorized repair or failure to
follow instructions supplied with the product,
or damage occurring during return shipment of
the product.
Exclusion of Certain Damages: This warranty
is exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability, right,
claim or remedy in contract or tort, whether
or not arising from the company’s negligence,
actual or imputed. No person or representative
is authorized to assume for the company any
other liability in connection with the sale of
this product. In no event shall the company be
liable for indirect, incidental or consequential
damages.
9
XIA3145 OPERATION
Specifications
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/-0.2V, 20Hz~20kHz)
Power Output: 100 Watts RMS x 2 channels at 4 ohms and < 1% THD+N
Signal to noise ratio: 74dBA (reference: 1 watt into 4 ohms)
Additional power output:
145 Watts RMS x 2 channels at 2 ohms and < 1% THD+N
290 Watts RMS x 1 channel at 4 ohms (bridged) and < 1% THD+N
Dynamic power: 580 Watts at 4 ohms
Speaker output impedance: 2~8 ohms (stereo), 4~8 ohms (bridged)
illuminite output voltage: 12VDC
illuminite output current: 2 amp
Low level input range: 200mV~6V (10k ohms)
High level input range: 2V~10V (100 ohms)
Bass boost: 0~12dB @ 45Hz
Crossover range: 40~400Hz
Crossover slope: 12dB/octave
Power supply: 11-16 VDC, negative ground
Fuses: 20 amp ATO x 2, 2 amp ATO x 1
Amplifier dimensions: 16.02" x 2.36" x 9.65" (WxHxD)
(407 x 60 x 245 mm)
Typical installation dimensions: 17" x 3.5" x 10.5" (WxHxD)
(432 x 89 x 267 mm)
10
XIA3145 OPERATION
Troubleshooting
Problem
Cause
Action
Unit will not turn on
+12V wire not connected or incorrect voltage Check connections for proper voltage
(no power LED indicator) REM wire not connected or incorrect voltage
(11~16VDC)
GND wire not connected
Check connection to ground
Replace fuse(s)
Fuse(s) blown
Unit has power - LED is Speaker wires not connected
Check connections at speakers
Increase volume level at head unit
green (but no sound)
Volume turned all the way down
One or more speaker wires touching each
other or touching chassis ground
Insulate all bare speaker wires from
each other and chassis ground
Speaker(s) defective or damaged
Input signal not connected
Check/replace speaker(s)
Check high or low level inputs for
proper connection
Unit blows fuse(s)
Engine noise
Incorrect fuse rating
Use fuse(s) with correct rating
Check for pinched wire
+12V wire touching chassis ground
Speaker(s) defective or damaged
Bad ground connection
Check/replace speaker(s)
Make sure amplifier is grounded to
clean bare metal
Signal ground loop or RFI
(radio frequency interference)
Re-route RCA cables from existing
high current wiring
LED illuminates red
(protect mode)
One or more speaker wires touching each
other or touching chassis ground
Insulate all bare speaker wires from
each other and chassis ground
Speaker(s) defective or damaged internally
(shorted)
Check/replace speaker(s)
Speaker load less than 2 ohms (stereo)
Speaker load less than 4 ohms (bridged)
Adjust speaker load - amplifier will
not operate at less than 4 ohms when
bridged
Distorted audio output
Low audio output
Weak bass
Incorrect input signal type or input level too
high
Check connections and reduce/adjust
input level
Incorrect input signal type or input level
too low
Check connections and increase/
adjust input level
Speaker(s) are wired out of phase
Check (+) and (-) speaker connections
(Observe correct polarity)
No illuminite output
(no lights)
Fuse blown - illuminite output (+12VDC) wire Check or replace fuse
touching ground
Use 2 amp ATO fuse only
illuminite (+) or (-) wires not connected
Check connections at speakers
illuminite connections wired wrong
(reverse polarity)
Reverse (+) and (-) connections
(Observe correct polarity)
illuminite speaker(s) defective or damaged
Check/replace speaker(s)
11
Dual Electronics Corp.
Toll Free: 1-866-382-5476
©2006 Dual Electronics Corp.
NSA0406-V01
|