Important
Please read PRECAUTIONS, this User’s Manual, and the Setup Manual
(separate volume) carefully to familiarize yourself with safe and
effective usage.
•Please refer to the Setup Manual for basic information ranging from
connection of the monitor to a PC to using the monitor.
•The latest User’s Manual is available for download from our web site:
Notice for this Monitor
Notice for this monitor
Aside from general purposes like creating documents, viewing multimedia content, this product is also suited to
applications such as graphics creation and digital photo processing, where accurate color reproduction is a priority.
This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is
used outside the region, it may not operate as specified in the specifications.
This product may not be covered by warranty for uses other than those described in this manual.
The specifications noted in this manual are only applicable when the following are used:
· Power cords provided with the product
· Signal cables specified by us
Only use optional products manufactured or specified by us with this product.
As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the monitor 30 minutes or more
after the monitor power has been turned on.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a
stable display.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime. (Refer to
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on
the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.
The backlight of the LCD panel has a fixed lifetime. When the screen becomes dark or begins to flicker, please contact
your dealer.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such as interference
patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage your panel. (If the pressure
marks remain on the panel, leave the monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt
to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may
occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until
the dew condensation disappears, otherwise it may cause some damage to the monitor.
3
Notice for this Monitor
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or
panel, and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
If necessary, the stains on the cabinet and panel surface can be removed by using the provided
ScreenCleaner.
To use the monitor comfortably
•An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
•Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
4
Table of Contents
Table of Contents
Table of Contents .................................................. 5
5
1. Introduction
1. Introduction
Thank you very much for choosing an EIZO Color Monitor.
1-1. Features
•22.5” wide format LCD
•Wide color gamut of 97% of Adobe RGB
•Applicable to HDCP
•WUXGA(1920 × 1200)display compliant
•Supports SDI signal inputs (BNC: HD/SD-SDI x 2, or Dual Link SDI x 1)
Resolution : 2048 dots x 1080 lines
•Supports SDI signal outputs (BNC x 2, Loop-through)
•Supports DVI / D-SUB signal inputs (DVI-D×1, D-SUB×1)
[Horizontal scanning frequency]
Analog :
Digital :
26 - 92kHz
26 - 78kHz
[Vertical scanning frequency]
Analog :
Digital :
23.8 - 86Hz
23.8 - 61Hz (VGA TEXT: 69 - 71Hz)
[Frame Synchronous mode supported]: 23.8 - 30.5Hz, 47.5 - 61Hz
•Color Mode function reproduces color gamut and gamma compliant with [EBU/Rec.709/
SMPTE-C] broadcasting standards as well as the [DCI] digital cinema standard (Refer to "2-4.
•The provided “ColorNavigator” calibration software enables you to calibrate monitor characteristics
and generate ICC profiles (for Windows) and Apple ColorSync profiles (for Macintosh) (Refer to
• Smoothing function incorporated for the adjustment of an enlarged image
•Sharpness function (OutlineEnhancer)
•Height adjustable stand
• Attaching the “Adjustment Certificate” to describe the grayscale and uniformity characteristics of
the monitor individually
6
1. Introduction
1-2. Controls and Functions
SCAN
TYPE
SIGNAL SCREEN
FORMAT SIZE
INFO
DVI/
D-SUB
SDI
MODE
ENTER
Adjustment menu
(ScreenManager ® *)
SCAN
TYPE
SIGNAL SCREEN
FORMAT SIZE
INFO
DVI/
D-SUB
SDI
MODE
ENTER
1
2
3
4
5
6
7
1. DVI / D-SUB Input Signal Selection button
2. SDI Input Signal Selection button
3. Mode button
4. Enter button
5. Control buttons (Left, Down, Up, Right)
6. Power button
7. Power indicator
Indicator status
Operation status
Blue
The screen is displayed
Flashing blue (2 times for When the timer is set for ColorNavigator, notifies that a recalibration is required (for
each)
Orange
Off
CAL mode).
Power saving
Power off
*
ScreenManager ® is an EIZO’s nickname of the Adjustment menu.
7
1. Introduction
1-3. Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with the monitor. The following table shows the disk
contents and the overview of the software programs.
Disk contents and software overview
The disk includes software programs for adjustment and User’s Manual. Refer to “Readme.txt” or the
“read me” file on the disk for software startup procedures or file access procedures.
Item
Overview
For Windows For Macintosh
A “Readme.txt” or “read me” file
√
√
ColorNavigator
An application software for calibrating monitor
characteristics and generating ICC profiles (for Windows)
and Apple ColorSync profiles (for Macintosh).
(A PC must be connected to the monitor with the supplied
USB cable.) Refer to the descriotion later.
√
√
Screen Adjustment Monitor pattern display software used when adjusting the
Utility image of the analog input signal manually.
Screen adjustment Used when adjusting the image of the analog signal input
–
√
pattern files
manually. If the Screen Adjustment Utility is not applicable
to your PC, use this pattern files to adjust the image.
–
√
√
User’s Manual (PDF file)
√
To use ColorNavigator
Refer to the corresponding User’s Manual on the CD-ROM disk in order to install and use the software.
When using this software, you will need to connect a PC to the monitor with the supplied USB cable.
8
1. Introduction
1-4. Basic Operation and Functions
Basic Operation
Adjustment menu allows you to adjust screen performance though the main menu and select a Color
mode easily.
Adjustment menu
(ScreenManager®)
Enter button
Power button
SCAN
TYPE
SIGNAL SCREEN
FORMAT SIZE
INFO
DVI/
D-SUB
SDI
MODE
ENTER
SCAN
TYPE
SIGNAL SCREEN
FORMAT SIZE
INFO
DVI/
D-SUB
SDI
MODE
ENTER
Color Mode Menu
Control buttons
(Left, Down, Up, Right)
Mode button
Note
•The Adjustment menu and the Color Mode menu cannot be displayed at the same time.
1
Entering the Adjustment menu
Press
once to display the main menu of the Adjustment menu.
2
3
Making Adjustments and Settings
1. Select the desired sub menu icon using
and press
. The sub menu appears.
2. Use
3. Use
to select the desired setting icon and press
to make all required adjustments and press
. The setting menu appears.
save the settings.
Exiting the Adjustment menu
1. To return to the main menu, select the <Return> icon
or press
or press
twice, followed by
twice, followed by
.
2. To exit the Adjustment menu, select the <Exit> icon
..
Tips
•Double clicking
at any time also exits the Adjustment menu.
9
1. Introduction
Functions
The following table shows all the Adjustment menu’s adjustment and setting menus.
Main menu
Sub menu
SDI DVI D-SUB
Reference
Setup
Black Insertion
√
√
√
22)
Pseudo Interlace
Range Extension
SDI Settings
Reset
Auto Adjustment
Clock
Phase
Position
Resolution
Range Adjustment
Screen Size
Smoothing
Signal Filter
-
-
-
√
-
-
-
-
-
-
-
-
-
12)
√
√
√
√
-
-
-
-
-
√
√
√
√
√
√
√
√
√
√
Screen
-
Switch mode if noise appears on the
√
√
-
√
√
-
screen.
Sharpness
Display Area
12bit Mode
Black Level
Brightness
Temperature
Gamma
Saturation
Hue
Gain
-
-
-
-
-
-
12)
√
√
√
√
√
√
√
√
√
√
√
√
√
√
1
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Color (Custom)
*
Reset
On
Off
PowerManager
Others
Border Intensity
Power Indicator
24)
√
√
√
Button Guide
Menu Settings Menu Size
Change the size of the menu.
Adjust the menu position.
Set the menu displaying time.
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Menu Position
Menu Off Timer
Reset
Return to the factory Default
2
settings.
*
Information
Language
Information
Review the Adjustment menu’s
√
√
√
√
√
√
settings, model name, serial number
3
and usage time.
*
English, German, French,
Spanish, Italian, Swedish,
Chinese(Simplified),
Chinese(Traditional) and
Japanese
Select the Adjustment menu’s
language.
*1
The adjustable functions on the <Color> menu depend on the selected Color mode (page 18). The above table shows the sub
*2
*3
The <Setup> settings are not reset.
The usage time is not always “0” when you purchase the monitor due to factory inspection.
10
2. Adjusting Screen
2. Adjusting Screen
2-1. Setting Screen Resolution
Compatible Resolutions/Frequencies
For details on compatible resolutions, refer to “Compatible Resolutions/Frequencies” in the Setup
Manual.
Setting Resolution
When you connect the monitor to the PC and find that the resolution is improper, or when you want to
change the resolution, follow the procedure below. When using video editing equipment, refer to the
instruction manual for the equipment.
Windows Vista
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Personalize”.
3. On the “Personalization” window, click “Display Settings”.
4. On the “Display Settings” dialog, select the “Monitor” tab and select desired resolution in the
“Resolution” field.
5. Click the “OK” button.
6. When a confirmation dialog is displayed, click “Yes”.
Windows XP
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Properties”.
3. When the “Display Properties” dialog is displayed, click the “Settings” tab and select desired
resolution for “Screen resolution” under “Display”.
4. Click the “OK” button to close the dialog.
Mac OS X
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog, select the “Display” tab and select desired resolution in the “Resolutions”
field.
4. Your selection will be reflected immediately. When you are satisfied with the selected resolution,
close the window.
11
2. Adjusting Screen
2-2. Setting SDI Input Signal
Note
•These settings can only be made when using the SDI input signal.
The following settings are located on the <Setup> menu of the Adjustment
menu.
Setting Pseudo Interlace
This display method shows the interlaced signals as they are and gives the video a CRT-like display
effect.
Tips
•<Pseudo Interlace> can be set under these conditions:
- The input signal is 1080i and the scan type on the <SDI Settings> menu is set to “Interlace”.
- The input signal is 1080i and the <SDI Settings> menu is set to “Auto” (default setting).
[Procedure]
1. From the <Setup> menu on the Adjustment menu, select <Pseudo Interlace>.
2. Select “On”.
Note
•When <Pseudo Interlace> is set to “On”, <Black Insertion> cannot be set.
Expanding Signal Output Range
The signal range can be expanded to meet the input signal from 64/1023 - 1019/1023 to 0/1023 -
1023/1023.
[Procedure]
1. From the <Setup> menu on the Adjustment menu, select <Range Extension>.
2. Select “On”
Setting SDI Signal
This setting sets the scan type and signal format.
[Procedure]
1. From the <Setup> menu on the Adjustment menu, select <SDI Settings>.
2. Select “Manual”
3. Select a scan type (Interlace, Progressive, or PsF).
4. Select a signal format (YUV 4:2:2, YUV 4:4:4, or RGB 4:4:4).
Tips
•The signal format can be set if the SDI signal input is SDI-Dual (A-B) or SDI-Dual (B-A).
•The signal format is set to YUV 4:2:2 if the SDI input signal is SDI-1 or SDI-2.
12
2. Adjusting Screen
The following settings are located on the <Screen> menu of the Adjustment menu.
Adjusting Sharpness
Emphasizes the outline of the image by emphasizing the color difference
between the pixels composing the image and to improve a sense of quality and
materiality.
Note
[Procedure]
1. From the <Screen> menu on the Adjustment menu, select <Sharpness>.
2. Adjust the setting with
(0 to 10).
Adjusting Display Area
The display area can be moved when using a 2048-by-1080 input signal.
[Procedure]
1. From the <Screen> menu on the Adjustment menu, select <Display Area>.
2. Adjust the setting with
(2 to -2).
Selecting Effective Bits for a 12-Bit Signal
This function selects the effective bits for displaying a 12-bit signal.
[11:2]: Displays a signal formed by the upper 10 bits. (Default setting)
[9:0]: Displays a signal formed by the lower 10 bits.
Tips
•<12bit mode> can be set under these conditions.
-The input signal is SDI-Dual (A-B) or SDI-Dual (B-A), and the <SDI Settings> (see previous page)
menu is set to “Manual” and the signal format is set to “RGB4:4:4”.
-The input signal is SDI-Dual (A-B), SDI-Dual (B-A) or “RGB4:4:4”, and the <SDI Settings> (see
previous page) menu is set to “Auto”.
[Procedure]
1. From the <Screen> menu on the Adjustment menu, select <12bit mode>.
2. Select [11:2] or [9:0] with
.
13
2. Adjusting Screen
2-3. Displaying Screen Correctly (Analog Input Only)
Note
•Allow the LCD monitor to stabilize for at least 30 minutes before making image adjustments.
The monitor displays the digital input image correctly based on its pre-setting data.
The monitor screen adjustment is used to suppress flickering of the screen or adjust screen position
and screen size correctly according to the PC to be used.
To use the monitor comfortably, adjust the screen when the monitor is set up for the first time or when
the settings of the PC in use are updated.
Adjustment Procedure
1
Perform the auto screen adjustment.
1. From the <Screen> menu on the Adjustment menu, select <Auto Adjustment>.
2. Select “Execute”
The Auto Adjustment function begins (showing a running status icon) to adjust flickering,
screen position, and screen size automatically.
Note
•The Auto Adjustment function is intended for use on the Macintosh and on AT-compatible PC
running Windows. It does not work properly when an image is displayed only on a part of the
screen (command prompt window, for example) or when a black background (wallpaper, etc.)
is in use.
• It cannot work correctly using with some graphics cards.
If the screen is not displayed correctly after performing step 1, follow the steps below to adjust the screen.
2
Prepare the display pattern for the analog display adjustment.
Windows
1. Load the “EIZO LCD Utility Disk” to your PC.
2. Start the “Screen Adjustment Utility” from the startup menu. If it cannot be started, open the
screen adjustment pattern files.
Tips
• For how to open and use the screen adjustment pattern files, refer to “Readme.txt” file.
Other than Windows
Tips
•For details and instructions on opening the “Screen adjustment pattern files”, refer to the “Read
me” file.
14
2. Adjusting Screen
3
Perform the auto size adjustment again with the analog screen adjustment
pattern displayed.
1. Display Pattern 1 in full screen on the monitor using the “Screen Adjustment Utility” or the
screen adjustment pattern files.
2. From the <Screen> menu on the Adjustment menu, select <Auto Adjustment>.
3. Select “Execute”
The Auto Adjustment function begins (showing a running status icon) to adjust flickering,
screen position, and screen size automatically.
4
Adjust by using <Screen> menu in the Adjustment menu
(1)Vertical bars appear on the screen
Use the <Clock> adjustment.
Select the <Clock> and eliminate the vertical bars by using
and
of the Control buttons.
Do not continuously press the Control buttons, as the adjustment value will change quickly
and make it difficult to locate the most suitable adjustment point. If the horizontal flickering,
blur or bars appear, proceed to <Phase> adjustment as follows.
(2) Horizontal flickering, blurring or bars appear on the screen.
Use the <Phase> adjustment.
Select the <Phase> and eliminate the horizontal flickering, blurring or bars by using
buttons.
and
Note
•Horizontal bars may not completely disappear from the screen depending on the PC.
15
2. Adjusting Screen
(3) The screen position is incorrect.
Use the <Position> adjustment.
The correct displayed position of the monitor is decided because the number and the position
of the pixels are fixed. The <Position> adjustment moves the image to the correct position.
Select <Position> and use
to adjust the position so that the entire image is
displayed. If vertical bars of distortion appear after finishing the <Position> adjustment, return
to <Clock> adjustment and repeat the previously explained adjustment procedure. (“Clock” =>
“Phase” => “Position”)
(4) Screen image is smaller or larger than the actual screen images.
Use the <Resolution> adjustment.
Adjustment is needed when the input signal resolution and the resolution now being displayed
are different.
Select <Resolution> and confirm if the resolution now being displayed is the same as the
input resolution. If it is not, adjust the vertical resolution using
horizontal resolution using and
and
and adjust the
.
Extra image is displayed due to excessive dots.
A part of image is cut due to short dots.
5
Adjust the output signal range (Dynamic Range) of the signal.
Use the <Range Adjustment> of <Screen> menu.
This controls the level of output signal range to display the whole color gradation (256 colors).
[Procedure]
1. Display Pattern 2 in full screen on the monitor using the “Screen Adjustment Utility” or the
screen adjustment pattern files.
2. Choose <Range Adjustment> from the <Screen> menu, and press
.
3. Select “Execute”
Color gradation is adjusted automatically.
4. Close the Pattern 2. When using the “Screen Adjustment Utility”, close the program.
16
2. Adjusting Screen
2-4. Adjusting Color
Simple Adjustment (Switching Color Mode)
Changing the color mode enables you to set the monitor to the appropriate display mode.
Selecting Color Mode
Pressing
displays the Color Mode menu at the bottom left of the screen. Each press of
changes
through 7 modes.
Press
to exit the menu.
->Custom->sRGB->EBU->Rec709->SMPTE-C->DCI->CAL
Tips
•The Adjustment menu and the Color Mode menu cannot be displayed at the same time.
Color Mode Menu
[EX.]Custom
Power button
Enter button
Current Mode
SCAN
TYPE
SIGNAL SCREEN
FORMAT SIZE
INFO
Settings status of Black
Level, Brightness, Tem-
perature and Gamma
DVI/
D-SUB
SDI
MODE
ENTER
Mode button
Control buttons
Color Mode
Selectable Color modes are as follows.
Mode
Purpose
Custom
Available for the color settings according to your preference.
sRGB
Suitable for color matching with sRGB compatible peripherals.
Suitable for reproducing the color gamut and gamma as set forth by EBU (European Broad-
casting Union) standards.
EBU
Suitable for reproducing the color gamut and gamma as set forth by the ITU-R Rec. 709
standard.
Rec709
SMPTE-C
DCI
Suitable for reproducing the color gamut and gamma as set forth by SMPTE-C standards.
Suitable for reproducing the color gamut and gamma as set forth by DCI standards.
Displays the screen adjusted by calibration software.
CAL
Color Adjustment of the Mode Settings
<Black Level>, <Brightness>, <Temperature> and <Gamma> settings can be adjusted on the Color
Mode menu. Select the desired function icon with
and adjust with
Control buttons.
(Setting(s) of <Temperature> and/or <Gamma> is defined as standard default in some modes.)
Note
•“CAL” mode can be adjusted only by Calibration Software “ColorNavigator”.
17
2. Adjusting Screen
Advanced Adjustments [Adjustment menu]
Color settings of each Color mode can be adjusted and saved by using the <Color> menu of the
Adjustment menu.
In the analog input, perform the “Range Adjustment” before making the color adjustments. During color
adjustments, the color mode cannot be changed. Select the mode in advance by using
.
Adjustment Items
The adjustable items and displayed icons on the <Color> menu depend on the selected color mode.
Regarding the adjustment items, refer to the “Adjustment Contents” on the next page.
“
”: Settable/Adjustable “ - ”: Fixed at the factory
√
Icons
Functions
Color Mode
Custom sRGB
EBU
Rec709 SMPTE-C
DCI
CAL
Black Level
*
*
*
*
√
√
√
√
√
√
√
√
√
√
√
√
-
√
√
√
√
√
-
√
√
√
√
-
√
√
Brightness
Temperature
Gamma
Saturation
Hue
-
-
√
√
√
-
√
√
√
-
-
-
-
-
-
-
-
-
Gain
-
-
-
-
-
-
Reset
√
√
√
√
√
√
*
These settings can be also adjusted on the Color Mode menu.
Note
•Allow the LCD monitor to stabilize for at least 30 minutes before making image adjustments. (Allow
the monitor to warm up for at least 30 minutes before making adjustments.)
•The values shown in percentages represent the current level within the specific adjustment. They are
available only as a reference tool. (To create a uniform white or black screen, the percentages for
each will probably not be the same.)
18
2. Adjusting Screen
Adjustment Contents
Menu
Function Descriptions
Adjustable range
Black Level
Brightness
Temperature
To adjust the black level as desired
0 - 32
To set the brightness of the screen
Tips
0~100%
•The values shown in the “%” are available only as reference.
To set the color temperature
5000K~10000K
in 500 K increments (including 5400K and
9300 K)
Tips
•The values shown in the Kelvin are available only as a reference tool.
•While color temperature is adjusted, <Gain> is adjusted automatically according to the
color temperature.
•If the temperature is set below 5000 K or over 10000 K, the setting of <Temperature>
is turned “Off”.
•If <Gain> is set, the setting of <Temperature> is turned “Off”.
•The default setting for each sRGB/EBU/REC709/SMPTE-C/DCI mode is set to “Std.”,
which is the temperature in conformity with each standard.
Gamma
To set the gamma value
1.6 - 2.7
Tips
•If setting the gamma value, the using the monitor in the digital signal input is
recommended. If using the monitor in the analog input signal, set the gamma value
from 1.8 to 2.2.
•The default setting for each sRGB/EBU/REC709/SMPTE-C/DCI mode is set to “Std.”,
which is the gamma in conformity with each standard.
Saturation
To change the saturation
-100~100
Setting the minimum level (-100) turns the
image to the monochrome.
Note
•This function does not enable to display every color gradation.
Hue
To change the flesh color, etc.
-100~100
Note
•This function does not enable to display every color gradation.
Gain
To change each color
(red, green and blue)
0~100%
By adjusting the red, green and blue color
tones for each mode, custom colors can be
defined. Display a white or gray background
image and adjust the <Gain>.
Tips
•The values shown in the “%” are available only as reference.
•The <Temperature> setting invalidates this setting. The <Gain> setting varies with
color temperature.
Note
•This function does not enable to display every color gradation.
Reset
To return the color settings to the
default settings
Select the <Reset>.
19
2. Adjusting Screen
2-5. Changing Screen Size Ratio
The screen size ratio can be selected using the <Screen Size> function on the <Screen> menu.
Changing Screen Size Ratio for Input Screen
->
Select the <Screen Size>.
Select the <Screen Size> in the <Screen> menu and select the screen size by using
.
and
When using DVI/D-SUB input signal
Mode
Function
Enlarged
Displays the picture on the screen in full, irrespective of the picture’s resolution.
Since the vertical resolution and horizontal resolution are enlarged at same rates,
some horizontal or vertical image may disappear.
Normal
Displays the picture on the screen using the same resolution of the input signal.
Enlarged
Normal
(Default Setting)
When using SDI input signal (input signal NTSC or PAL)
Mode Function
Dot by Dot
4:3
Displays the picture on the screen using the same resolution of the input signal.
Displays the input video expanded to a vertical resolution of 1080 while maintaining
the aspect ratio to 4:3 (horizontal: vertical).
16:9
Displays the input video expanded to a vertical resolution of 1080 while maintaining
the aspect ratio to 16:9 (horizontal: vertical).
Letter Box
Displays the letter box input video expanded to a vertical resolution of 1080 while
maintaining the aspect ratio.
Dot by Dot
4:3
(Default Setting)
16:9
16:9
Letter Box
Letter Box
20
2. Adjusting Screen
When using SDI input signal (input signal 720p)
Mode
Function
Dot by Dot
Enlarged
Displays the picture on the screen using the same resolution of the input signal.
Displays the input video expanded to a vertical resolution of 1080 while maintaining
the aspect ratio.
Dot by Dot
Enlarged
(Default Setting)
The setting must be adjusted in the following instances after changing the screen size ratio.
Smooth the blurred texts of the enlarged screen.
Switch the <Smoothing> setting.
Select the suitable level from 1 - 5 (Soft - Sharp).
Select <Smoothing> in the <Screen> menu and adjust by using the right and left switches.
Note
•Smoothing setting may not be required depending on the display resolution. (You cannot
choose the smoothing icon.)
Set the brightness of the black area surrounding the displayed image.
Set the <Border Intensity>.
In “Normal” or “Enlarged” mode, the outer area (border) may appear black.
Select <BorderIntensity> in the <Others> menu and adjust by using
.
Border
21
2. Adjusting Screen
2-6. Setting Black Insertion
This setting inserts a black screen to suppress blur when showing moving images.
[Procedure]
1. From the <Setup> menu on the Adjustment menu, select <Black Insertion>.
2. Select “On”
Note
•The brightness may drop when set to “On”.
•When set to “On”, the screen may flicker if the DVI/D-SUB input signal exceeds the frame sync
frequency range.
•When set to “On”, the brightness will not change even if set to 45% or more.
22
3. Setting Monitor
3. Setting Monitor
3-1. Setting Power Saving
The <PowerManager> menu in the Adjustment menu enables to set the power saving.
Note
• Do your part to conserve energy, turn off the monitor when you are finished using it. Turning off the
main power switch or unplugging the power cord completely shuts off power supply to the monitor.
• Devices connected to the USB port (upstream and downstream) work when the monitor is in power
saving mode or when the power button of the monitor is Off. Therefore, power consumption of the
monitor varies with connected devices even in the power saving mode.
• When using ColorNavigator, turning of the power saving function is recommended.
Analog Input
This monitor complies with the “VESA DPM”.
[Procedure]
1. Set the PC’s power saving settings.
2. Select “On” from the <PowerManager> menu.
[Power Saving System]
PC
Monitor
Power Indicator
ON
Operation
Blue
STAND-BY
SUSPEND
OFF
Power saving
Power saving
Orange
[Power Resumption Procedure]
Operate the mouse or keyboard to return to a normal screen.
Digital Input
• DVI: This monitor complies with the DVI DMPM standard.
• SDI: This monitor complies with our original power saving function “SDI”.
[Procedure]
1. Set the PC’s power saving settings.
2. Select “On” from the <PowerManager> menu.
[Power Saving System]
The monitor enters the power saving mode in five seconds in connection with the PC setting.
PC or Video Editing Equipment
Monitor
Operation
Power Indicator
Blue
ON
Power saving
Power saving
Orange
[Power Resumption Procedure]
Operate the mouse or keyboard to return to a normal screen.
23
3. Setting Monitor
3-2. Locking Button Operation
Use the “Adjustment Lock” function to prevent any accidental changes.
Buttons that can be locked
•
(Enter button) / Adjustments/settings using
•
•
(Mode button)
(DVI/D-SUB Input Signal Selection button)
Buttons that cannot be locked
•
•
•
(SDI Input Signal Selection button)
(Power button)
(Control buttons)
[How to lock]
1. Press
to turn off the monitor.
2. Press
again while pressing
.
The screen is displayed with the adjustment lock.
[How to unlock]
1. Press
to turn off the monitor.
2. Press
again while pressing
.
The screen is displayed with the adjustment lock released.
3-3. Setting Power Indicator
The brightness of the power indicator (blue) when the screen is displayed can be adjusted (default
setting is set to light up when power is turned on, and brightness is set to 4).
[Procedure]
1. Select <Power Indicator> in the Adjustment menu <Others> menu.
2. Set the brightness with
(Off or 1 to 7).
3-4. Setting Button Guide
The Button Guide can be changed between show/hide (default setting is set to show the Button Guide).
[Procedure]
1. Select <Button Guide> in the Adjustment menu <Others> menu.
2. Select “On” or “Off”.
24
4.Troubleshooting
4.Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local dealer.
•No-picture problems : See No.1 - No.2
•Imaging problems : See No.3 - No.16
•Other problems : See No.17 - No.21
•USB problems : See No.22
Problems
Possible cause and remedy
1.No picture
•Check whether the power cord is connected correctly. If
the problem persists, turn off the monitor, and then turn
it on again a few minutes later.
•Power indicator does not light.
•Turn the main power switch on.
•Press
.
•Power indicator is lighting blue.
•Set each adjusting value in <Brightness> or <Gain> to
•Power indicator is lighting orange.
•Switch the input signal with
or
.
•Operate the mouse or keyboard.
•Check whether the PC is turned on.
•Check whether the signal cable is connected properly.
2.The message below appears.
This message appears when the signal is not input
correctly even when the monitor functions properly.
•This message appears when no signal is input.
•The message shown left may appear, because some
(This is displayed for about 40 seconds)
PCs do not output the signal soon after power-on.
•Check whether the PC is turned on.
•Check whether the signal cable is connected properly.
•Switch the input signal with
or
.
•The message below shows that the input signal is out of
the specified frequency range. (Such signal frequency is
displayed in red.)
•Check whether the signal setting of your PC matches
the resolution and the vertical frequency settings for the
Example:
•Reboot the PC.
•Select an appropriate display mode using the graphics
board’s utility. Refer to the manual of the graphics board
for details.
fD: Dot Clock
(Displayed only when the digital signal inputs)
fH: Horizontal Frequency
fV: Vertical Frequency
3.Display position is incorrect.
•Move the image to the correct position using the
•If the problem persists, use the graphics board’s utility if
available to change the display position.
25
4.Troubleshooting
Problems
Possible cause and remedy
4.Screen image displayed is smaller or larger than the
actual screen image.
•Adjust the resolution using <Resolution> so that the
input signal resolution equals the resolution in the
resolution adjustment menu (page 16).
5.Vertical bars appear on the screen or a part of the image •Adjust using <Clock> (page 15).
is flickering.
6.The characters and images have several vertical bars on •Adjust the characters and images using the
their right side.
<Signal Filter>.
7.Whole screen is flickering or blurring.
•Adjust using <Phase> (page 15).
8.Characters are blurred.
9.Upper part of the screen is distorted as shown below.
•This is caused when both composite sync (X-OR)
signal and separate vertical sync signal are input
simultaneously. Select either composite signal or
separate signal
10.The screen is too bright or too dark.
11.Afterimages appear.
•Adjust <Brightness>. (The LCD monitor backlight has a
fixed life span. When the screen becomes dark or begins
to flicker, contact your local dealer.)
•Use a screen saver for a long-time image display.
•Afterimages are particular to LCD monitors. Avoid
displaying the same image for a long time.
12.Green/red/blue/white dots or defective dots remain on
the screen.
•This is due to LCD panel characteristics and is not a
failure.
13.Interference patterns or fingerprints remain on the
screen.
•Leave the monitor with a white screen or a black screen.
The symptom may disappear.
14.Noise appears on the screen.
•When entering the signals of analog input, select 1 to
4 in <Signal Filter> from the <Screen> menu to change
the mode.
•When entering the signals of HDCP system, the normal
images may not be displayed immediately.
15. The screen flickers.
•Set <Black Insertion> to “Off” on the <Screen> menu.
•Change the input signal to a sync signal.
16. Screen does not appear correctly when using SDI input •Check whether the scan type is set correctly.
signal.
•Check whether the signal format is set correctly.
•Check whether the <Screen Size> is set correctly.
•Check the SDI settings.
26
4.Troubleshooting
Problems
Possible cause and remedy
17.The <Smoothing> icon on the Adjustment menu
<Screen> cannot be selected.
• Smoothing setting may not be required depending on
the display resolution. (You cannot choose the smoothing
icon.)
•<Smoothing> is disabled when the screen is displayed in
the following resolutions.
•1920 x 1200 or higher
•800 × 600, selecting [Enlarged] duirng <Screen Size>
•960 × 600, selecting [Enlarged] duirng <Screen Size>
•1600 × 1200, selecting [Enlarged] duirng <Screen
Size>
•Selecting “Dot by Dot” or “Normal” during <Screen
Size>
•Using an SDI input signal other than NTSC, PAL, or
720p
18.The <Sharpness> icon on the Adjustment menu
<Screen> cannot be selected.
•<Smoothing> is disabled when the screen is displayed in
the following resolutions.
•Using a DVI/D-SUB input signal
•1920 x 1200 or higher
•800 × 600, selecting [Enlarged] duirng <Screen Size>
• 960 × 600, selecting [Enlarged] duirng <Screen
Size>
•1600 × 1200, selecting [Enlarged] duirng <Screen
Size>
•Selecting “Dot by Dot” during <Screen Size>
•Using an SDI input signal other than NTSC, PAL, or
720p
19.The Main menu of Adjustment menu does not start.
20.The Color Mode menu does not start.
•Check for Adjustment Lock function (page 24).
•This function does not work when digital signal is input.
21.The auto adjust function does not work correctly.
•This function does not work correctly with some graphics
boards.
22.The monitor connected with the USB cable is not
detected. / USB devices connected to the monitor does
not work.
•Check that the USB cable is correctly connected.
•Check the downstream ports by connecting the
peripherals to other downstream ports. If the problem is
solved by doing this, contact an EIZO dealer. (For details,
refer to the manual of the PC.)
•Reboot the PC
•If the peripheral devices work correctly when the PC and
peripheral devices are connected directly, please contact
your local dealer.
•Check that the PC and OS are USB compliant. (For
verification of USB support, consult the manufacturer of
each system.)
•Check the PC’s BIOS setting for USB when using
windows. (For details, refer to the manual of the PC.)
27
5. Reference
5. Reference
5-1. Attaching an Arm
The stand can be removed and replaced with an arm (or another stand) to be attached to the monitor.
Note
•When attaching an arm or stand, follow the instructions of their user’s manual.
•When using another manufacturer’s arm or stand, confirm the following in advance and select one
conforming to the VESA standard.
- Hole spacing on the arm mounting: 100 mm x 100 mm
- Thickness of plate: 2.6 mm
- Strong enough to support weight of the monitor unit (except the stand) and attachments such as
cables.
•When using an arm or stand, attach it to meet the following tilt angles of the monitor.
- Up 45 degrees, down 45 degrees (horizontal display)
•Please connect cables after attaching an arm stand.
•Since the monitor and arm are so heavy, dropping them may result in injury or equipment damage.
Setup Procedure
1
2
3
Lay the LCD monitor on a soft cloth spread over on a stable surface with
the panel surface facing down.
Remove the stand. (Prepare a screwdriver.)
Unscrew the four screws securing the unit and the stand with the screwdriver.
Attach an arm stand to the LCD monitor securely.
Secure the monitor to the arm or stand using the screws specified in the user’s manual of the
arm or stand.
28
5. Reference
5-2. Connecting More than Two PCs to the Monitor
More than two PCs can be connected to the monitor through the D-Sub mini 15 pin, the DVI-D and the
SDI (BNC) connector on the back of the monitor.
Connection examples
To PC1
D-Sub mini
15-pin Connector
D-Sub
Signal cable
(supplied MD-C87)
To PC 2
DVI-D connector
DVI
Signal cable
(supplied FD-C39)
To PC 3 or video
editing equipment
BNC Connector
SDI
BNC cable (option)
Selecting input signal
Switch the input signal with
or
. When the signal is switched, the active signal type (DVI, D-SUB
or SDI) appears at the top right corner of the screen.
Input Signal Selection button
SCAN
TYPE
SIGNAL SCREEN
FORMAT SIZE
INFO
DVI/
D-SUB
SDI
MODE
ENTER
29
5. Reference
5-3. Utilizing USB (Universal Serial Bus)
This monitor provides a hub which supports the USB standard. When connecting to a USB compliant
PC or another hub, the monitor functions as a hub to which the USB compliant peripherals can be
easily connected.
Required system environment
• PC equipped with USB ports or another USB hub connected to the USB compliant PC
• Windows 2000/XP/Vista // Mac OS 9.2.2/Mac OS X 10.2 or later
• USB Cable (MD-C93, enclosed)
Note
• The USB hub function may not work properly depending on the PC or peripherals. Please consult
the manufacturer of each device about the USB support.
• Using the USB Rev. 2.0 compatible PC or peripherals is recommended.
• Devices connected to the USB port (upstream and downstream) work when the monitor is in power
saving mode or when the power button of the monitor is Off. Therefore, power consumption of the
monitor varies with connected devices even in the power saving mode.
• When the main power switch is Off, device connected to the USB port will not operate.
• The followings are procedures for the Windows 2000/XP/Vista and Mac OS.
Connecting to the USB HUB
1
2
Connect the monitor to the PC with the signal cable first, then turn on the
PC.
Connect the upstream port of the monitor to the downstream port of the
USBcompliant PC or another hub by using the USB cable.
After connecting the USB cable, the USB function can be set up automatically.
3
After setting up, the monitor’s USB hub is available for connecting USB
compliantperipherals to the downstream ports of the monitor
Upstream
Downstream
30
5. Reference
5-4. Specifications
Size
LCD Panel
57 cm (22.5 inch)
Surface
Hard Coating
treatment
Surface
2H
hardness
Response Time Approx. 12 ms
(CR: 10 or more)
Viewing Angle Horizontal : 176°, Vertical : 176°
Dot Pitch
Analog
Digital
0.252 mm
26 - 92kHz
26 - 78kHz
23.8 - 86Hz
Horizontal Scan
Frequency
Analog
Vertical Scan
Frequency
Digital
23.8 - 61Hz (VGA TEXT : 69 - 71Hz)
Resolution
1920 dots x 1200 lines
162MHz
Analog
Digital
Dot Clock
(Max.)
162MHz
Display Colors
1073.74 million colors
Recommended Brightness
Display Area
100 cd/m2 or less (with color temperature of between 5000K to 6500K)
483.84 mm (H) × 302.4 mm (V) (19” (H) x 11.9” (V))
Power Supply
100-120/200-240 VAC 10%, 50/60 Hz, 1.1 A/0.55A
Power
Consumptionl
Screen Display 110 W (with USB load)
On
100 W (without USB load)
Power Saving 7 W or less (for single signal input, without USB load)
Mode
Power Button
off
1 W or less (without USB load)
Main Power
switch off
0 W
Input Signal Connector
D-Sub mini 15-pin x 1
DVI-D connector (Applicable to HDCP) x 1
BNC connector (HD/SD-SDI) x 2 complies to IEC60169-8, 75
BNC connector (Loop-through) x 2
Separate, TTL, Positive/Negative
Composite, TTL, Positive/Negative
0.7 Vp-p / 75 ohms, Positive
Ω
Output Signal Connector
Analog Input Signal (Sync)
Analog Input Signal (Video)
Input Signal (Digital) (DVI)
TMDS (Single Link)
Signal
registration
Analog
Digital
45 (Factory preset: 9)
10 (Factory preset: 0)
Plug & Play
Dimensions
Analog / Digital (DVI-D) : VESA DDC 2B / EDID structure 1.3
with stand
567 mm (W) x 481 ~ 599 mm (H) x 255 mm (D)
(22.3” (W) x 18.9” ~ 23.6” (H) x 10” (D))
without stand
567 mm (W) x 389 mm (H) x 113 mm (D)
(22.3” (W) x 15.3” ~ 23.6” (H) x 4.4” (D))
with stand
Approx. 13.4 kg (29.5 lbs.)
Approx. 8.8 kg (19.4 lbs.)
Weight
without stand
Tilt:
Swivel:
Adjustable height:
40° Up, 0° Down
35° Right, 35° Left
118 mm (4.6 inch)
Movable range
31
5. Reference
Environment
Conditions
Temperature
Humidity
Operating:
0°C ~ 35°C (32°F ~ 95°F)
Transportation/Storage:
-20°C ~ 60°C (-4°F ~ 140°F)
Operating:
Transportation/Storage:
30% to 80% R.H. Non-condensing
30% to 80% R.H. Non-condensing
Pressure
Operating:
Transportation/Storage:
700 to 1060 hPa.
200 to 1060 hPa.
Revision 2.0
USB
standard
USB port
USB Specification
Upstream port x 1
Downstream port x 2
Communication
Speed
480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Power Supply Downstream: 500 mA for each (max.)
Main default settings (factory settings)
Brightness
Smoothing
20%
3
Temperature
Color Mode
PowerManager
Screen Size
6500K
Custom
On
Enlarged
Enlarged
45 sec
Off
Off
Off
Auto
Menu Settings
Menu Size
Menu Off Timer
Black Insertion
Pseudo Interlace
Range Extension
SDI Settings
Language
English
32
5. Reference
Dimensions
unit: mm (inch)
500(19.7)
240(9.4)
323(12.7)
35°
35°
SWIEVEL
567(22.3)
233.5(9.2)
172.5(6.8)
100(3.9)
233.5(9.2)
486.5(19.2)
113(4.4)
64
(2.52)
255(10)
311(12.2)
406(16)
33
5. Reference
Pin Assignment
•DVI-D Connector
3
1
9
17
2
4
12
20
6
7
8
16
24
5
13
21
10 11
19
14 15
22 23
18
Pin No.
Signal
Pin No.
9
Signal
T.M.D.S. Data1-
Pin No.
17
Signal
T.M.D.S. Data0-
T.M.D.S. Data0+
T.M.D.S. Data0/5 Shield
NC*
1
2
3
4
5
6
7
T.M.D.S. Data 2-
T.M.D.S. Data 2+
T.M.D.S. Data2/4 Shield
NC*
10
T.M.D.S. Data1+
T.M.D.S. Data1/3 Shield
NC*
18
11
19
12
20
NC*
13
NC*
21
NC*
DDC Clock (SCL)
DDC Data (SDA)
14
+5V Power
22
T.M.D.S. Clock shield
T.M.D.S. Clock+
15
Ground (return for +5V,
Hsync, and Vsync)
23
8
NC*
16
Hot Plug Detect
24
T.M.D.S. Clock-
(NC*: No Connection)
•D-Sub mini 15-pin connector
4
3
2
1
5
10
9
8
7
6
11
14 13 12
15
Pin No.
Signal
Signal
Red video ground
Green video ground
Blue video ground
Signal
Pin No.
Pin No.
1
2
3
4
5
Red video
6
7
11
12
13
14
15
NC
*
Green video
Blue video
Data (SDA)
H.Sync
8
9
V.Sync
NC
*
NC
*
Ground
10
Ground
Clock (SCL)
(NC*: No Connection)
•USB Port
Upstream
Downstream
Series B
Series A
Connector
Connector
No.
1
2
3
4
Signal
Remarks
Cable power
Serial data
Serial data
VCC
- Data
+ Data
Ground
Cable Ground
34
5. Reference
5-5. Glossary
Clock
With the analog input signal display, the analog signal is converted to a digital signal by the LCD
circuitry. To convert the signal correctly, the LCD monitor needs to produce the same number clock
pulse as the dot clock of the graphics system. When the clock pulse is not correctly set, some verti-
cal bars of distortion are displayed on the screen.
DVI (Digital Visual Interface)
A digital flat panel interface. DVI can transmit digital data from the PC directly without loss with the
signal transition method “TMDS”. There are two kinds of DVI connectors. One is DVI-D connector for
digital signal input only. The other is DVI-I connector for both digital and analog signal inputs.
DVI DMPM (DVI Digital Monitor Power Management)
The Power management system for the digital interface. The “Monitor ON” status (operation mode)
and the “Active Off” status (power-saving mode) are indispensable for the DVI-DMPM as the moni-
tor’s power mode.
Gain Adjustment
Adjusts each color parameter for red, green and blue. The color of the LCD monitor is displayed
through the color filter of the LCD panel. Red, green and blue are the three primary colors. The col-
ors on the monitor are displayed by combining these three colors. The color tone can change by ad-
justing the illumination amount passed through each color’s filter.
Gamma
Generally, the relationship that the light intensity values of a monitor change nonlinearly to the input
signal level is called “Gamma Characteristic”. On the monitor, low gamma values display the whitish
images and high gamma values display the high contrast images.
HDCP (High-bandwidth Digital Contents Protection)
Digital signal coding system developed to copy-protect the digital contents, such as video, music,
etc. This helps to transmit the digital contents safely by coding the digital contents sent via DVI ter-
minal on the output side and decoding them on the input side.
Any digital contents cannot be reproduced if both of the equipments on the output and input sides
are not applicable to HDCP system.
Phase
The phase adjustment decides the sampling timing point for converting the analog input signal to a
digital signal. Adjusting the phase after the clock adjustment will produce a clear screen.
Range Adjustment
The Range Adjustment controls the level of output signal range to display the whole color gradation.
35
5. Reference
Resolution
The LCD panel consists of a fixed number of pixel elements which are illuminated to form the screen
image. The display panel of this monitor consists of 1920 horizontal pixels and 1200 vertical pixels.
At a resolution of 1920 x 1200 , images are displayed as a full screen(1:1).
SDI (Serial Digital Interface)
One of the interfaces standardized by the SMPTE and ARIB. It transmits image signals, sync signal,
clock, and audio signals all on one cable.
sRGB (Standard RGB)
“International Standard for Red, Green, and Blue color space” A color space was defined with the
aim of the color matching between applications and hardware devices, such as monitors, scanners,
printers and digital cameras. As a standard default space, sRGB allows Internet users to closely
match colors.
Temperature
Color Temperature is a method to measure the white color tone, generally indicated in degrees Kel-
vin. At high temperatures the white tone appears somewhat blue, while at lower temperatures it ap-
pears somewhat red. Computer monitors generally give best performance at high temperature set-
tings.
5000 K: Slightly reddish white (usually used in print industry)
6500 K: White called daylight color (suited for web browsing)
9300 K: Slightly bluish white (usually used for television)
TMDS (Transition Minimized Differential Signaling)
A signal transition method for the digital interface.
VESA DPM
(Video Electronics Standards Association - Display Power Management)
VESA specifications achieve increased energy efficiency for computer monitors. This involves stan-
dardization of signals sent from the computer (graphics board).DPM defines the status of signals
transmitted between the computer and monitor.
36
6. Preset Timing
6. Preset Timing
The following table shows factory preset video timing (for analog signal only).
Note
•Display position may be deviated depending on the PC connected, which may require screen
adjustment using Adjustment menu.
•If a signal other than those listed in the table is input, adjust the screen using the Adjustment menu.
However, screen display may still be incorrect even after the adjustment.
•When interlace signals are used, the screen cannot be displayed correctly even after screen
adjustment using the Adjustment menu.
Frequency
Horizontal: kHz
Vertical: Hz
Mode
Dot clock
Polarity
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
31.47
59.94
31.47
70.09
37.88
60.32
48.36
60.00
60.00
60.00
63.98
60.02
75.00
60.00
65.29
59.95
74.04
59.95
Negative
Negative
Negative
Positive
Positive
Positive
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Positive
Negative
Positive
Positive
Negative
VGA 640×480@60Hz
28.3MHz
VGA TEXT 720×400@70Hz
VESA 800×600@60Hz
28.3 MHz
40.0 MHz
65.0 MHz
108.0 MHz
108.0 MHz
162.0MHz
146.3 MHz
154.00MHz
VESA 1024×768@60Hz
VESA 1280×960@60Hz
VESA 1280×1024@60Hz
VESA 1600×1200@60Hz
VESA CVT 1680×1050 60Hz
VESA CVT 1920×1200 60Hz
Horizontal
Vertical
37
For U.S.A, Canada, etc. (rated 100-120 Vac) Only
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will required to correct the interference at his own expense.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference within the
limits of a Class A digital device.
AC Cord
-
-
Shielded Signal Cable (enclosed)
Canadian Notice
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe A est comforme à la norme NMB-003 du Canada.
For Europe, etc. (rated 200-240 Vac) Only
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user
may be required to take adequate measures.
Warnung
Bey dem gerät handelt es sich um ein Klasse-A-Produkt. Bei Betrieb des Geräts in Wohnumgebungen ist gegebenenfalls
durch entsprechende Maßnahmen dafür zu sorgen, dass eine Störung des Radio- und Fernsehempfangs vermieden wird.
Avertissement
Cet appareil est de classe A. Il est susceptible de créer des interférences radio dans un environnement domestique, dans
ce cas l’utilisateur devra prendre les mesures appropriées.
38
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor
Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige
Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden. Bei der
Auswahl des Schwenkarms sind die nachstehenden Hinweise zu berücksichtigen:
Der Standfuß muß den nachfolgenden Anforderungen entsprechen:
a)Der Standfuß muß eine ausreichende mechanische Stabilität zur Aufnahme des Gewichtes vom Bildschirmgerät
und des spezifizierten Zubehörs besitzen. Das Gewicht des Bildschirmgerätes und des Zubehörs sind in der
zugehörenden Bedienungsanleitung angegeben.
b)Die Befestigung des Standfusses muß derart erfolgen, daß die oberste Zeile der Bildschirmanzeige nicht höher
als die Augenhöhe eines Benutzers in sitzender Position ist.
c)Im Fall eines stehenden Benutzers muß die Befestigung des Bildschirmgerätes derart erfolgen, daß die Höhe der
Bildschirmmitte über dem Boden zwischen 135 – 150 cm beträgt.
d)Der Standfuß muß die Möglichkeit zur Neigung des Bildschirmgerätes besitzen (max. vorwärts: 5°, min. nach
hinten ≥ 5°).
e)Der Standfuß muß die Möglichkeit zur Drehung des Bildschirmgerätes besitzen (max. ±180°). Der maximale
Kraftaufwand dafür muß weniger als 100 N betragen.
f) Der Standfuß muß in der Stellung verharren, in die er manuell bewegt wurde.
g)Der Glanzgrad des Standfusses muß weniger als 20 Glanzeinheiten betragen (seidenmatt).
h)Der Standfuß mit Bildschirmgerät muß bei einer Neigung von bis zu 10° aus der normalen aufrechten Position
kippsicher sein.
Hinweis zur Ergonomie :
Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB2000 mit dem Videosignal, 1920×
1200, Digital Eingang und mindestens 60,0 Hz Bildwiederholfrequenz, non interlaced. Weiterhin wird aus
ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte
Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.)
„Maschinenlärminformations-Verordnung 3. GPSGV:
Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779“
39
4th Edition-March, 2012
03V22517D1
Copyright © 2008-2012 EIZO NANAO CORPORATION All rights reserved.
(U.M-CG232W)
|