User’s Guide
HDSDI-ACR 100
SDI-AVR 100
High Definition SDI to Component Video/RGB Converter
SDI to Video/RGB Converter
68-553-01 C
Printed in the USA
02 02
Installation
RGB/Component (HDSDI-ACR 100) or RGB/YUV (SDI-
AVR 100) switch — Set this switch to the Off position to
output RGB video. Set the switch on for component video.
IN
R/R-Y
G/Y
V
B/B-Y
COMPOSITE
OUTPUT
S-VIDEO
OUTPUT
5
OUT
H
S
ON
ON
OFF
OFF
100-240V
50/60 Hz 0.2A
SDI INPUT
OUTPUTS
Bi/tri-level switch (HDSDI-ACR 100 only) — Set this
switch to the On position to output tri-level sync on the
component video output. Set the switch off for bi-level
sync.
6
1
2
7
3
4
ON
Figure 4 — SDI-AVR 100 rear panel
OFF
Composite Output connector (SDI-AVR 100 only) — Connect a
composite video display device to this BNC connector. This
3
HDSDI-ACR 100 switch configuration
RGB/
Component
output is available whenever an active SDI signal is applied to the
Output video format
RGBHV/RGBS
SOG
Off
Bi/tri-level
Either
Either
Off
1
SDI input connector,
.
Off
Off
On
On
RGsB
On
S-video Output connector (SDI-AVR 100 only) — Connect an
S-video device to this 4-pin mini DIN connector. This output is
4
Y, R-Y, B-Y w/ bi-level on Y
Y, R-Y, B-Y w/ tri-level on Y
Either
Either
On
available whenever an active SDI signal is applied to the SDI
1
input connector,
.
SDI-AVR 100 switch configuration
Output video format
RGBHV/RGBS
RGsB
SOG RGB/YUV
RGB/component video output connectors
5
Off
On
Off
Off
On
Ensure that the rear panel DIP switches are in the correct
configuration (see Rear Panel Controls).
Y, R-Y, B-Y
Either
R/R-Y
G/Y
B/B-Y
RGBHV video connection —
Connect to five BNC connectors
as shown.
Set Up switch (SDI-AVR 100 only) — Set this switch to the On position
to output an NTSC signal that is on the 7.5 IRE pedestal. Set the
switch off to return the signal to the normal level.
RGBHV
Video
H
V
S
RGBS video connection —
Connect to four BNC connectors
as shown.
Beta switch (SDI-AVR 100 only) — Set this switch to the On position to
set the color level of the YUV output to the Betacam level. Set the
switch off to restore the YUV output to the normal level. If a
Betacam signal is input, the switch should be set to On to output
the Betacam format. Otherwise, the output will be NTSC or PAL.
R/R-Y
G/Y
V
B/B-Y
RGsB and component video
connection — Connect to three
BNC connectors as shown.
RGBS
Video
H
S
Color Bars switch (SDI-AVR 100 only) — Set this switch to the On
position to output NTSC or PAL color bars. Set the switch off for
the converted video input.
AC power connector — Plug a
standard IEC power cord into
this connector to connect the
converter to a 100 to 240VAC, 50
Hz or 60 Hz power source.
6
R/R-Y
G/Y
V
B/B-Y
NTSC/PAL switch (SDI-AVR 100 only) — Used in conjunction with
the Color Bars switch only, set this switch to the On position to
output PAL color bars. Set the switch off for NTSC color bars.
RGsB or
Component
Video
H
S
Front Panel Indicators
Rear Panel Controls
All indicators are on the front panel. Figure 5 and figure 6 show
HDSDI-ACR 100 and SDI-AVR 100 indicators.
DIP switches
7
Power LED — The Power LED indicates that power is on.
1
2
SOG switch — Set this switch to the On position to output sync-
on-green for RGB video (RGsB). Set the switch off for
RGBHV or RGBS video.
720P LED (HDSDI-ACR 100 only) — The 720P LED indicates that
the converter is outputting the HDTV 720P video format.
4
HDSDI-ACR 100 and SDI-AVR 100 • Installation
HDSDI-ACR 100 and SDI-AVR 100 • Installation and Operation
5
Indicators and Specifications
The equalization applied to the SDI-AVR 100’s input signal is
sufficient for an input coaxial cable length of at least 1000 feet (305
meters) of Extron SHR cable or Belden 8281 cable.
FORMAT
720P
1080I
1080P
HDSDI-ACR 100
HDSDI TO VIDEO/RGB CONVERTER
The equalization applied to the HDSDI-ACR 100’s input signal is
sufficient for an input coaxial cable length of at least 330 feet (100
meters) of Extron SHR cable or Belden 8281 cable.
1
2
3
4
Figure 5 — HDSDI-ACR 100 front panel
Minimum/maximum levels ...... 0.5V to 1.0V p-p with no offset
Impedance .................................... 75 ohms
Return loss .................................... >-15dB @ 0 MHz to 270 MHz
Maximum DC offset .................... 0.5V
LOCK
SDI-AVR 100
SDI TO VIDEO/RGB CONVERTER
Video processing
Encoder ......................................... 10 bit digital
1
5
Frequency response ..................... Luminance ................ 0 to 5.75 MHz, 0.5dB
Chroma .................... 0 to 2.75 MHz, 0.5dB
Figure 6 — SDI-AVR 100 front panel
S/N ................................................ >70dB
RGB matrix error ......................... <1%
1080I LED (HDSDI-ACR 100 only) — The 1080I LED indicates
that the converter is outputting the HDTV 1080I video format.
3
4
5
1080P LED (HDSDI-ACR 100 only) — The 1080P LED indicates
that the converter is outputting the HDTV 1080P video format.
Video signal characteristics — for color bar output on the
SDI-AVR 100 only
Dot clock ....................................... 27 MHz
Lock LED (SDI-AVR 100 only) — The Lock LED indicates that
the converter is locked to the 270 Mbs input signal.
Pixel clock accuracy ..................... 30 ppm
Specifications
Video output
Number/signal type
Video
SDI-AVR 100 .................... 1 composite video and 1 S-video, and
1 analog RGBHV/RGBS/RGsB or component
video (Y, R-Y, B-Y) (switch selectable)
Differential phase error .............. SDI-AVR 100 ............ <1º
Differential gain error ................. SDI-AVR 100 ............ <1%
HDSDI-ACR 100 .............. 1 analog RGBHV/RGBS/RGsB or component
video (Y, R-Y, B-Y) (switch selectable)
Connectors
Video input and loop-through
Number/signal type
SDI-AVR 100 .................... 1 SDI (4:2:2, SMPTE 259M-C)
HDSDI-ACR 100 .............. 1 HDSDI (SMPTE 292M)
Connectors
SDI-AVR 100 .................... 1 female BNC (composite video)
1 female 4-pin mini DIN (S-video)
6 female BNC (RGB, component video, or S-video)
HDSDI-ACR 100 .............. 6 female BNC
SDI-AVR 100 .................... 1 female BNC (SDI input)
Levels ............................................. Composite video ...... 1V p-p (nominal)
S-video .................... 1V p-p/luma, 0.3V p-p/
chroma (nominal)
1 female BNC (SDI reclocked loop-through)
HDSDI-ACR 100 .............. 1 female BNC (HDSDI input)
1 female BNC (HDSDI reclocked loop-through)
RGB
.................... 0.7V (nominal)
Component video .... Y = 1V p-p; R-Y, B-Y = 1V
p-p (nominal)
Levels depend on the format selected (NTSC, PAL, Betacam).
6
HDSDI-ACR 100 and SDI-AVR 100 • Specifications
HDSDI-ACR 100 and SDI-AVR 100 • Specifications
7
Impedance .................................... 75 ohms
Return loss .................................... -30dB @ 5 MHz
Sync
Output type .................................. RGBHV, RGBS, RGsB
Standards (SDI-AVR 100 only) .. NTSC 3.58, PAL 4.43, Betacam
Output impedance....................... 75 ohms
Max. rise/fall time....................... 200 nS
Polarity .......................................... SDI-AVR 100 ............ negative
HDSDI-ACR 100 ...... bi-level or tri-level sync
(switch selectable) on luma
(Y) leg
General
Power............................................. 100VAC to 240VAC, 50/60 Hz, internal, auto-
switchable
SDI AVR 100 ..................... 6 watts
HDSDI AVR 100 .............. 10 watts
Temperature/humidity .............. Storage -40° to +158°F (-40° to +70°C) / 10% to
90%, non-condensing
Operating +32° to +122°F (0° to +50°C) / 10% to
90%, non-condensing
Rack mount................................... Yes, with optional rack shelf, part #60-190-01
Enclosure type .............................. Metal
Enclosure dimensions ................. 1.75" H x 8.75" W x 8.0" D
(1 rack unit high, half-rack unit wide)
4.5 cm H x 22.2 cm W x 20.3 cm D
(Depth excludes connectors.)
Shipping weight .......................... 4 lbs (1.8 kg)
Product weight
SDI-AVR 100 .................... 1.8 lbs (0.8 kg)
HDSDI-ACR 100 .............. 1.9 lbs (0.9 kg)
Vibration ....................................... ISTA/NSTA 1A in carton (International Safe
Transit Association)
Listings .......................................... UL, CUL
Compliances ................................. CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF ............................................. 30,000 hours
Warranty ....................................... 3 years parts and labor
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
Extron Electronics, Japan
Daisan DMJ Building 6F
3-9-1 Kudan Minami
Chiyoda-ku, Tokyo 102-0074 Japan
+81.3.3511.7655
714.491.1500
+31.33.453.4040
+65.6383.4400
Fax 714.491.1517
Fax +31.33.453.4050
Fax +65.6383.4664
Fax +81.3.3511.7656
© 2002 Extron Electronics. All rights reserved.
|