3COM ROUTER 5000/6000 FAMILY
QUICK REFERENCE GUIDE
Overview
This Command Reference applies to the following Router 5000/6000 models running software version 3.0.
Router 5012 (3C13701)
Router 5232 (3C13751)
Router 5642 (3C13755)
Router 5682 (3C13701)
Router 6040 (3C13840)
Router 6080 (3C13880)
About the Command Line Interface
To use and navigate the command line interface of your unit, please refer to the following points for assistance:
■
When initially accessing the command line interface, press Enter when prompted. The User View menu for the unit
displays. This is indicated by the chevron brackets around the name of the unit at the prompt, for example,
<router5000-xx> (where xx is either EI or SI).
■
When in the System View menu, square brackets appear around the name of the unit at the prompt, for example,
[router5000-xx].
■
■
■
You must be in the System View menu to access the configurable CLI commands.
Some commands can be entered directly at any prompt from anywhere in the interface.
If you enter part of a command followed by a ? (with no space between), the CLI will show you all the commands
that begin in that way.
■
■
■
■
The term ‘view’ may be used interchangeably with the term ‘menu’.
The undo command is placed before the command you wish to undo, for example, undo setauthentication password.
<CTRL-A> places the cursor back to the start of the command line.
Enter the first few characters of a command and press TAB to enter the full command without having to input the
entire command (where there is only one command that starts with the entered characters).
■
■
■
Use the Up Arrow key at the prompt to repeat the previous command string.
Use the Delete key to delete the character after the cursor; the Backspace key deletes the character before the cursor.
When entering physical port numbers, Enter the port number as x/0/z, where x is the unit number and z is the
physical port number.
Copyright © 2006, 2007 3Com Corporation. All rights reserved.
www.3Com.com
Part Number: 10016467 Rev. AA
Published: October 2007
3Com Router 5000/6000 Family
Command Reference
3
abr-summary
Use the abr-summarycommand to configure the route aggregation on the area border router (ABR).
OSPF Area view
ISP Domain view
System view
access-limit
acl-reflect timeout
acl
Use the access-limitcommand to configure a limit to the amount of supplicants in the current ISP domain.
Use the acl-reflect timeoutcommand to set the global aging time of reflexive ACLs.
Use the aclcommand to create an access control list and enter ACL view.
System View
acl
Use the aclcommand to reference an ACL to control call-in and call-out of VTY (Telnet and SSH) users.
Use the accountingcommand to configure an accounting scheme for the current ISP domain.
User Interface view
ISP Domain view
accounting
accounting
Use the accountingcommand to set the IP address, port number and shared key for the primary and
secondary RADIUS accounting servers.
RADIUS Scheme view
RADIUS Scheme view
TACACS+ view
accounting
Use the accountingcommand to set the IP address, port number and shared key for the primary and
secondary RADIUS accounting servers.
accounting
Use the accountingcommand to set the IP address, port number and shared key for the primary and
secondary TACACS+ accounting servers.
accounting commands
accounting domain
Use the accounting commandscommand to enable the system to start per-command accounting for
terminal users logged into the user interface.
User Interface view
Use the accounting domaincommand to enable DHCP server accounting for addresses from the global
DHCP address pools and configure a domain for DHCP accounting.
DHCP Address Pool view
accounting-on
Use the accounting-on enablecommand to enable the user re-authentication at reboot function.
Use the accounting optionalcommand to enable optional accounting.
RADIUS view
accounting optional
ISP Domain view
RADIUS view
activate
Use the activatecommand to activate the ADSL interface.
Use the activatecommand to enable the G.SHDSL interface.
ATM (ADSL) Interface view
activate
ATM (G.SHDSL) Interface view
activation-key
Use the activation-keycommand to define a shortcut key or key combination for starting a terminal
session.
User Interface view
Voice Entity view
address
Use the addresscommand to configure the voice routing policy to the peer voice gateway.
4
3Com Router 5000/6000 Family
Command Reference
address
Use the addresscommand to configure a route to the peer voice gateway or assign an X.121 address for
a destination host.
Voice Entity view
Voice Entity view
address sip
Use the address sipcommand to set routing policy for reaching the remote voice gateway (VG) to SIP.
adsl standard
adsl tx_attenuation
adv-factor
Use the adsl standardcommand to set the standard applied to the ADSL interface.
ATM (ADSL) Interface view
ATM (ADSL) Interface view
Use the adsl tx_attenuationcommand to set attenuation value for ADSL transmit power.
Use the adv-factorcommand to configure the advantage factor which is used to count Mos and ICPIF
value in a jitter voice test.
HWPing Test Group view
aggregate
aggregate
Use the aggregatecommand to establish an aggregated record in the BGP routing table.
Use the aggregatecommand to create a multicast aggregated record in the BGP routing table.
BGP view
Use the aggregatecommand without parameters to create one local aggregated route and set atomic
aggregation attributes.
IPv4 Multicast Subaddress Family view
aging-time
Use the aging-timecommand to configure SYN status waiting timeout value and FIN status waiting timeout
value of TCP, session entry idle timeout value of TCP and UDP.
ASPF Policy view
ah authentication-algorithm
Use the ah authentication-algorithmcommand to set the authentication algorithm adopted by
Authentication Header protocol in IPSec proposal.
Use the undo ah authentication-algorithmcommand to restore the default setting.
IPSec Proposal view
ahdsl annex
Use the shdsl annexcommand to configure annex standard at an SHDSL interface. You cannot activate a
link with different standard types at its two ends.
ATM (G.SHDSL) Interface view
alarm (CT3 Interface)
alarm-threshold
algorithm-suite
allow l2tp
Use the alarmcommand to enable the CT3 interface to detect/send alarm signals.
CT3 Interface view
Use the alarm-thresholdcommand to configure the alarm thresholds on the CT1/PRI interface as needed.
CT1/PRI Interface view
Use the algorithm-suitecommand to specify the algorithm suite used when a client registers.
Dvpn-Class view
Use the allow l2tpcommand to specify the name of the peer end of the tunnel on receiving call and the
Virtual-Template it uses.
L2TP Group view
DLCI view
annexg
ani
Use the annexgcommand to enable T1.617 Annext G on the frame relay interface for data transmission.
Use the anicommand to enable or disable the terminating point to send the calling party information
(service category and calling number) to the originating point during call connecting process.
R2 CAS view
3Com Router 5000/6000 Family
Command Reference
5
ani-offset
Use the ani-offsetcommand to configure the number of digits of the called number to be collected prior
to requesting the calling party information.
R2 CAS view
R2 CAS view
answer
Use the answercommand to configure whether the terminating point is required to send answer signal.
apply access-vpn vpn-instance
Use the apply access-vpn vpn-instancecommand to specify to search private network forwarding routes
in vpn-name1, vpn-name2, vpn-name3, vpn-name4, vpn-name5, vpn-name6 (if they all
exist)and forward packets after policy routing is enabled to satisfy route-policy.
Route-Policy view
apply as-path
Use the apply as-pathcommand to specify the AS numbers to be added in front of the original AS path in
route-policy.
Routing Policy view
Routing Policy view
Routing Policy view
Routing Policy view
Route-Policy view
Routing Policy view
Route-Policy view
Route-Policy view
Route-Policy view
Route-Policy view
Route-Policy view
apply community
apply cost
Use the apply communitycommand to set BGP community attributes in route-policy.
Use the apply costcommand to set the route cost value of route information.
Use the apply cost-typecommand to set the route cost type of route information.
apply cost-type
apply default output-interface
Use the apply default output-interfacecommand to set default forwarding interface for packets.
apply ip-address
Use the apply ip-addresscommand to set the next hop address of route information.
apply ip-address default next-hop
Use the apply ip-address default next-hopcommand to set the default next hop of a packet.
apply ip-address next-hop (for Multicast Policy Routing)
Use the apply ip-addresscommand to configure the next hop IP address list in a route-node.
apply ip-address next-hop (for Unicast Policy Routing)
Use the apply ip-address next-hopcommand to set the packet next hop.
apply ip-dscp
apply ip-precedence
apply isis
Use the apply ip-dscpcommand to configure to modify the packet DSCP value matching the policy.
Use the apply ip-precedencecommand to set precedence of IP packets.
Use the apply isiscommand to apply the level of a matched route to be redistributed to Level-1, Level-2
or Level-1-2.
Routing Policy view
Routing Policy view
apply local-preference
Use the apply local-preferencecommand to apply the local preference of route information.
apply mpls-label
Use the apply mpls-labelcommand to assign MPLS labels for public network routes that match
route-policy filter conditions.
Route-Policy view
6
3Com Router 5000/6000 Family
Command Reference
apply origin
Use the apply origincommand to set the routing source of BGP routing information.
Routing Policy view
apply output-interface (for Multicast Policy Routing)
Use the apply output-interfacecommand to configure an outgoing interface list in a route-node.
Route-Policy view
Route-Policy view
apply output-interface (for Unicast Policy Routing)
Use the apply output-interfacecommand to set a packet forwarding interface.
apply policy outbound
Use the apply policy outboundcommand to set the frame relay virtual circuit queuing to CBQ
(Class-Based Queuing).
Frame Relay Class view
Routing Policy view
apply tag
Use the apply tagcommand to set the tag area of OSPF route information.
Use the areacommand to enter OSPF area view.
area
OSPF view
OSPF Area view
area
Use the areacommand to configure the type of busy tone detection for FXO voice subscriber-line.
Voice Subscriber-line view
area-authentication-mode
Use the area-authentication-modecommand to configure IS-IS to authenticate the received Level-1
routing information packets (LSP, CSNP and PSNP), according to the pre-defined mode and password.
IS-IS view
Voice Entity view
area-id (Voice Entity view)
Use the area-idcommand to configure the area ID of voice GW.
area-id (Voice GK Client view)
Use the area-idcommand to configure the H.323 gateway area ID.
Voice GK Client view
arp check enable
Use the arp check enablecommand to enable ARP entry check to have the device not learn the ARP
entries with broadcast MAC addresses.
System view
Ethernet interface view
Ethernet Interface view
Ethernet Interface view
arp-proxy enable
arp security
Use the arp-proxy enablecommand to enable proxy ARP on an interface.
Use the arp securitycommand to disable dynamic ARP learning on an Ethernet interface.
Use the arp security time-outcommand to configure the aging time of the authorized ARP entries.
arp security time-out
arp send-gratuitous-arp
Use the arp send-gratuitous-arpcommand to enable sending gratuitous ARP packet on this interface
periodically and set the sending period.
Bridge Template view
Ethernet Interface view
Ethernet Subinterface view
Gigabit Ethernet Interface view
Gigabit Ethernet Subinterface view
Virtual Ethernet interface view
VLAN Interface view
arp static
Use the arp staticcommand to configure ARP mapping table.
System view
3Com Router 5000/6000 Family
Command Reference
7
arp timer aging
Use the arp timer agingcommand to set the aging timer for dynamic ARP entries.
System view
OSPF view
asbr-summary
ascii
Use the asbr-summarycommand to configure summarization of redistributed routes by OSPF.
Use the asciicommand to set the type of the transmitted data to ASCII.
FTP Client view
aspf-policy
Use the aspf-policycommand to define an ASPF policy. For a defined policy, the policy can be invoked
through its policy number.
System view
async mode
Use the async modecommand to set the operating mode of the asynchronous serial interface.
Asynchronous Serial Interface view
AUX Interface view
AM Interface view
async mode padpos
Use the async mode padposcommand to configure a POSPAD access port.
Asynchronous Serial Interface view
AUX Interface view
async mode pos
Use the async mode pospos-numbercommand to create a POS access port in nontransparent
transmission and permanent TCP connection mode.
Asynchronous Serial Interface view
AM Interface view
FCM Interface view
AUX Interface view
async mode posapp
Use the async mode posappcommand to configure the interface to operate in POS application mode.
Asynchronous Serial Interface view
AUX Interface view
atm-class
Use the atm-classcommand to apply a set of parameters (which are defined in ATM-Class) to an ATM
interface or a PVC.
Interface view
PVC view
atm class
Use the atm classcommand to create an ATM-Class and enter the ATM-Class view.
Use the atm-cttcommand to set all interfaces on a board to transparent transmission.
System view
atm-ctt
ATM Interface view
atm-link check
Use the atm-link checkcommand to have the protocol state of the ATM P2P subinterface changes
depending on whether the physical interface is up and whether a PVC is configured on the subinterface.
ATM P2P Subinterface view
authentication
authentication
Use the authenticationcommand to configure an authentication scheme for the current ISP domain.
ISP Domain view
Use the authenticationcommand to set the IP address, port number and shared key for the primary and
secondary RADIUS authentication servers.
RADIUS Scheme view
authentication
Use the authenticationcommand to set the IP address, port number and shared key for the primary and
secondary TACACS+ authentication servers.
TACACS+ view
8
3Com Router 5000/6000 Family
Command Reference
authentication
Use the authenticationcommand to enable user authentication and authorization for the access service
number.
Voice Access-Number view
authentication
Use the authenticationcommand to set the IP address, port number and shared key for the primary and
secondary TACACS+ authentication servers.
TACACS+ view
authentication-algorithm
Use the authentication-algorithmcommand to select the authentication algorithm for an IKE proposal.
IKE Proposal view
authentication-client method
Use the authentication-client methodcommand to specify how the DVPN server that applies the DVPN
policy authenticates clients. None, CHAP, and PAP are currently available.
Dvpn-Policy view
Voice AAA view
authentication-did
authentication-method
authentication-mode
Use the authentication-didcommand to enable authentication for all one-stage dial (direct dial) users.
Use the authentication-methodcommand to select the authentication method used by an IKE proposal.
Use the authentication-modecommand to set the authentication mode at login.
IKE Proposal view
Use the authentication-mode nonecommand to set the authentication mode to none, that is, no
authentication at login.
User Interface view
OSPF Area view
Dvpn-Class view
authentication-mode
Use the authentication-modecommand to configure one area of OSPF to support the authentication
attribute.
authentication-server method
Use the authentication-server methodcommand to specify a client whether or not to authenticates the
DVPN server it accesses.
authentication super hwtacacs-scheme
Use the authentication super hwtacacs-schemecommand to configure super authentication scheme for
a domain.
ISP Domain view
ISP Domain view
authorization
authorization
Use the authorizationcommand to configure an authorization scheme for the current ISP domain.
Use the authorizationcommand to set the IP address, port number and shared key for the primary and
secondary TACACS+ authorization servers.
TACACS+ view
Voice Entity view
System view
authorization-level
auto-config
Use the authorization-levelcommand to configure a local caller authorization level for the voice entity.
Use the auto-configcommand to implement the auto-configoperation.
auto-config enable
auto-execute command
Use the auto-config enablecommand to enable auto-config.
System view
Use the auto-execute commandcommand to set a command to be automatically executed.
User Interface view
3Com Router 5000/6000 Family
Command Reference
9
balance
Use the balancecommand to configure the number of routes participating in BGP load balancing.
BGP view
System view
band-based-sharing
baudrate
Use the band-based-sharingcommand to enable bandwidth-based unbalanced load sharing.
Use the baudratecommand to set the baud rate of a serial interface.
Use the bertcommand to set test error bit for line Bit.
Serial Interface view
CE3 interface view
CT1/PRI Interface view
CT3 Interface view
System view
bert
bert (CT1/PRI Interface)
Use the bertcommand to start a BERT test on the CT1/PRI interface.
bert (CT3 Interface)
Use the bertcommand to start a BERT test on the CT3 interface.
bgp
Use the bgpcommand to enable BGP and enter the BGP view.
This command is used to enable and disable BGP as well as to specify the local AS number of BGP.
bims boot request
Use the bims boot requestcommand to enable the BIMS device to access the branch intelligent
management system (BIMS) center at startup.
System view
bims device-id string
Use the bims device-idcommand to configure the unique identifier of the BIMS device at the BIMS center.
Use the bims enablecommand to enable BIMS.
System view
System view
bims enable
bims interval
Use the bims intervalcommand to configure the interval for accessing the BIMS center. When the interval
is set to 0, the BIMS device does not access the BIMS center regularly.
System view
System view
System view
bims ip address
bims request
bims-server
Use the bims ip addresscommand to configure the IP address and port number of the BIMS center.
Use the bims requestcommand to have the BIMS device access the BIMS center.
Use the bims-servercommand to enable and configure BIMS option for a global address pool on the
DHCP server.
Global DHCP Address Pool view
bims sharekey
Use the bims sharekeycommand to configure the shared key between the BIMS device and the BIMS
center.
System view
System view
bims source ip-address
Use the bims source ip-addresscommand to specify a source IP address for the packets sent by the
BIMS device. It can be the IP address of a port on the router.
bims specify-time
Use the bims specify-timecommand to configure the BIMS device to access the BIMS center at the
specified time and if desired, configure the device to access the BIMS center at regular intervals from then
on during a specified period.
System view
10
3Com Router 5000/6000 Family
Command Reference
binary
Use the binarycommand to set data type to binary for file transfer.
Use the boot bootromcommand to upgrade BootRom.
FTP Client view
System view
System view
System view
boot bootrom
boot bootrom
bootfile backup
bootfile dir
Use the boot bootromcommand to upgrade BootRom.
Use the bootfile backupcommand to specify the backup boot file.
Use the bootfile dircommand to view information about all the boot files in the Flash, including file type,
date, time, file size, and file name.
System view
System view
System view
System view
bootfile main
Use the bootfile maincommand to specify the main boot file.
bridge aging-time
Use the bridge aging-timecommand to configure the aging time of the dynamic address table.
bridge bridge-set enable
Use the bridgebridge-setenablecommand to enable the specified bridge set.
bridge bridging
Use the bridge bridgingcommand to enable the bridging function of a network layer protocol on a
specified bridge set.
System view
System view
System view
System view
bridge enable
Use the bridge enablecommand to enable the bridging function.
bridge learning
bridge mac-address
bridge routing
Use the bridge learningcommand to enable forwarding by dynamic address table.
Use the bridge mac-addresscommand to manually configure a static address table entry of bridge.
Use the bridge routingcommand to enable the routing function of a specified bridge-set for the specified
network protocol.
System view
System view
bridge routing-enable
Use the bridge routing-enablecommand to enable the routing function of the bridge.
Use the bridge setcommand to add an interface to a bridge set.
bridge-set
Interface view
Bridge Template view
bridge-set (Ethernet Interface view)
Use the bridge-set (in the Ethernet Interface view)command to add the Ethernet interface into the
bridge.
Ethernet Interface view
bridge set (Synchronous Serial Interface view)
Use the bridge-set (in Synchronous serial interface system view)command to add the
synchronous serial interface encapsulated into SDLC into the bridge group.
Synchronous Serial Interface view
3Com Router 5000/6000 Family
Command Reference
11
bridge-set stp enable
Use the bridge-set stp enablecommand to disable STP on the port.
Interface view
Interface view
Interface view
System view
System view
System view
System view
System view
bridge-set stp port pathcost
Use the bridge-set stp port pathcostcommand to configure the path cost of the bridge port.
bridge-set stp port priority
Use the bridge-set stp port prioritycommand to configure the priority of the bridge port.
bridge stp ieee
Use the bridge stp ieeecommand to specify a bridge set to support IEEE STP.
Use the bridge stp max-agecommand to set the Max Age timer on the bridge.
Use the bridge stp prioritycommand to assign a priority to the bridge.
bridge stp max-age
bridge stp priority
bridge stp timer forward-delay
Use the bridge stp timer forward-delaycommand to set the Forward Delay timer on the bridge.
bridge stp timer hello
Use the bridge stp timer hellocommand to set the Hello Time timer on the bridge.
bridge vlanid-transparent-transmit enable
Use the bridge vlanid-transparent-transmit enablecommand to enable VLAN ID transparent
transmission.
Interface view
broadcast-limit link
Use the broadcast-limit linkcommand to configure the maximum number of links that the virtual
template supports for sending multicast or broadcast packets.
Virtual Template view
Ethernet Port view
PIM view
broadcast suppression
Use the broadcast-suppressioncommand to restrict the broadcast traffic size on the port.
Use the bsr-policycommand to restrict the range for valid BSR, preventing BSR spoofing.
bsr-policy
bump
Use the bumpcommand to configure the standby PVC that will take over when a specified PVC goes down.
ATM Pvc-Group view
busytone-t-th
Use the busytone-t-thcommand to configure the threshold of busy tone detection.
FXO Voice Subscriber-Line view
FTP Client view
bye
Use the byecommand to disconnect from the remote FTP server and exit to user view.
bye
Use the byecommand to terminate the connection to the remote SFTP server and exit to system view as
you would with the exitand quitcommands.
SFTP Client view
PIM view
c-bsr
c-rp
Use the c-bsrcommand to configure a candidate BSR.
Use the c-rpcommand to configure the router to advertise itself as a candidate RP to BSR.
PIM view
12
3Com Router 5000/6000 Family
Command Reference
ca identifier
Use the ca identifiercommand to specify the CA this device trusts and have the "name" CA bound with
this device.
PKI Domain view
CE1/PRI Interface view
ATM E1/T1 Interface view
cable
cable
cable
Use the cablecommand to set the cable length matching the CE1/PRI interface.
Use the cablecommand to set the cable length of the ATM E1 interface.
Use the cablecommand to configure the cable mode of ATM T3 cable, i.e., to set the distance between the
router and the cable distribution frame.
ATM T3 Interface view
cable (CT1/PRI Interface)
Use the cablecommand to set cable attenuation and length on a CT1/PRI interface to match the distance
of the transmission line.
CT1/PRI Interface view
CT3 Interface view
MSDP view
cable (CT3 Interface)
cache-sa-enable
call-mode
Use the cablecommand to configure the length of the cable with which a CT3 interface is connected.
Use the cache-sa-enablecommand to enable the router to cache SA state.
Use the call-modecommand to configure a call-mode for calls between local router and peer router.
Voice Entity view
callednumber receive-method
Use the callednumber receive-methodcommand to enable the device to place a call immediately after all
digits of the called number are collected or after a pound sign (#), the terminator, is received.
Use the caller-permit command to configure the calling numbers that are permitted to call in.
Use the carcommand to configure traffic monitoring for a behavior.
Voice Access-Number view
caller-permit
Voice Entity view
car
Traffic Behavior view
card-digit
Use the card-digitcommand to configure the number of digits in a card number for an access service
number.
Voice Access-Number view
cas
cbs
Use the cascommand to enter the R2 CAS view and digital E&M Signaling view.
Use the cbscommand to set the committed burst size of frame relay virtual circuit.
CE1/PRI Interface view
Frame Relay Class view
System view
ccc interface out-interface
Use the ccc interface out-interfacecommand to create a local CCC connection.
ccc interface transmit-lsp receive-lsp
Use the ccc interface transmit-lsp receive-lspcommand to create a remote CCC connection.
System view
cd
Use the cdcommand to change the current path on the SFTP server. If you do not specify the remote-path
argument, the current path is displayed.
SFTP Client view
3Com Router 5000/6000 Family
Command Reference
13
cd
Use the cdcommand to change the current working directory of the user to the specified directory.
User view
FTP Client view
Voice AAA view
SFTP Client view
FTP Client view
MPLS L2VPN view
PVC view
cd
Use the cdcommand to change the current working directory path on the remote FTP server.
Use the cdrcommand to configure the saving rule for call detail record.
Use the cdupcommand to quit to the upper directory.
cdr
cdup
cdup
Use the cdupcommand to return from the current working directory path to the upper directory.
Use the cecommand to create a CE or modify the CE range.
ce
cell-packing
Use the cell-packingcommand to set the maximum number of cells to be packed in one PVC.
certificate request entity
Use the certificate request entitycommand to specify the name of the entity for certificate request.
PKI Domain view
certificate request from
Use the certificate request fromcommand to choose between CA and RA to register for certificate
request.
PKI Domain view
PKI Domain view
certificate request mode
Use the certificate request modecommand to decide between the manual or the auto request mode.
certificate request polling
Use the certificate request pollingcommand to specify the interval between two polls and the retry
times.
PKI Domain view
PKI Domain view
certificate request url
Use the certificate request urlcommand to specify the server URL for certificate request through
SCEP protocol. SCEP is a protocol specialized in the communication with authentication authorities.
channel
Use the channelcommand to add X.25 interface or XOT channel of one serial port to the current hunt group.
X.25 Hunt Group view
CE1/PRI Interface view
CT1/PRI Interface view
ISDN BRI Interface view
RIP view
channel-set (CE1/PRI Interface)
Use the channel-setcommand to bundle some timeslots of a CE1/PRI interface into a channel-set.
channel-set (CT1/PRI Interface)
Use the channel-setcommand to bundle timeslots on the CT1/PRI interface into a channel-set.
channel-set timeslot
checkzero
Use the channel-set timeslot command to configure a B channel for leased line service.
Use the checkzerocommand to check the zero field of RIP-1 packet.
cid display
Use the cid displaycommand to enable caller identification display.
Voice Subscriber-Line view
14
3Com Router 5000/6000 Family
Command Reference
cid enable
Use the cid enablecommand to enable CID on the FXO interface.
Voice Subscriber-Line view
cid select-mode
Use the cid select-modecommand to configure the route selection mode used by the calling party to set
up VoFR calls.
DLCI view
cid send
Use the cid sendcommand to enable the FXO or FXS module to send calling numbers to the IP side.
Voice Subscriber-Line view
cid type
Use the cid typecommand to configure the format of transmitted information about the calling party.
Voice Subscriber-Line view
Frame Relay Class view
Frame Relay Class view
Policy view
cir
Use the circommand to set the CIR of frame relay virtual circuit.
cir allow
Use the cir allowcommand to set the CIR ALLOW of frame relay virtual circuit.
Use the classifier behaviorcommand to specify the behavior for the class in the policy.
classifier behavior
clear-forward-ack
Use the clear-forward-ackcommand to enable or disable the terminating point to respond by sending a
clear-back signal when the originating point (calling party) disconnects a call.
R2 CAS view
System view
System view
clns enable
Use the clns enablecommand to enable CLNS.
clns erpacket enable
Use the clns erpacket enablecommand to enable generation of error report packets.
clns erpacket interval
Use the clns erpacket intervalcommand to set the minimum interval to generate two successive error
report packets.
System view
System view
System view
System view
System view
System view
clns es-peer
Use the clns es-peercommand to configure a static neighboring ES.
Use the clns netcommand to assign an NET address to the IS.
Use the clns rdpacket enablecommand to enable the router to send RD packets.
clns net
clns rdpacket enable
clns rdpacket interval
Use the clns rdpacket intervalcommand to set the minimum interval to generate RD packets.
clns route-static
Use the clns route-staticcommand to configure a static OSI route.
clns timer rdpacket holding
Use the clns timer rdpacket holdingcommand to set the holding time of the information a RD packet
carries.
System view
clock
Use the clockcommand to set the clock mode of the ATM E1/T1 interface.
ATM E1/T1 Interface view
3Com Router 5000/6000 Family
Command Reference
15
clock
Use the clockcommand to set the clock mode of ATM E3/T3 interface.
ATM E3/T3 Interface view.
ATM Interface view
clock
clock
clock
clock
Use the clockcommand to set the clock mode on an ATM interface.
Use the clockcommand to specify ATM interface to use internal transmission clock signal.
Use the clockcommand to set the clock mode of the CPOS interface.
Use the clockcommand to set the clock mode of the POS interface.
ATM Master Interface view
CPOS Interface view
POS Interface view
clock (CE1/PRI Interface)
Use the clockcommand to set the clock mode on a CE1/PRI interface.
CE1/PRI Interface view
CE3 Interface view
clock (CE3 Interface)
clock (CT1/PRI Interface)
Use the clockcommand to set clocking on the CT1/PRI interface.
CT1/PRI Interface view
CT3 Interface view
Serial intervace view
System view
clock (CT3 Interface)
Use the clockcommand to set the clock mode on the CT3 interface.
clock (Serial Interface)
Use the clockcommand to set clock selection mode for a synchronous serial interface.
clock datetime
Use the clock datetimecommand to set the current time and date of the router.
clock summer-time
Use the clock summer-timecommand to set the name, and starting and ending time of the daylight saving
time.
System view
System view
clock timezone
Use the clock timezonecommand to set local time zone information.
close
Use the closecommand to terminate the connection to the remote FTP server, but remain in FTP client
view.
FTP Client view
cng-on
Use the cng-oncommand to enable comfort noise function.
Voice Subscriber-Line view
cngced-detection
Use the cngced-detectioncommand to set the threshold parameters for CNG/CED signal detection.
Voice Subscriber-Line view
CE1/PRI Interface view
CT1/PRI Interface view
code (CEI/PRI Interface)
Use the codecommand to set the line code format for a CE1/PRI interface.
code (CT1/PRI Interface)
Use the codecommand to set the line code format on the CT1/PRI interface.
16
3Com Router 5000/6000 Family
Command Reference
code nrzi
Use the code nrzicommand to set the digital signal coding format to None-Return-to-Zero-Inverse (NRZI)
for a synchronous serial interface.
Synchronous Serial Interface view
code nrzi
Use the code nrzicommand to configure the NRZI encoding of the synchronous serial port.
Synchronous Serial Interface System view
System view
command-alias enable
command-alias mapping
command-privilege
Use the command-alias enablecommand to enable the command alias function.
Use the command-alias mapping command to map an alias to a keyword.
System view
Use the command-privilege levelcommand to assign a command level to the commands in a specified
view.
System view
common-name
Use the common-namecommand to specify the common name of an entity, take User name for example.
PKI Entity view
compare-different-as-med
Use the compare-different-as-medcommand to enable comparison of MED values of routes from
neighbors residing in different ASs when determining the best route.
BGP Unicast view
BGP Multicast view
VPNv4 view
compression
Use the compressioncommand to configure the voice coding method according to priority level.
Use the confederation idcommand to configure confederation identifier.
Voice Entity view
BGP view
confederation id
confederation nonstandard
Use the confederation nonstandardcommand, the router can be compatible with the AS confederation
not adopting RFC1965.
BGP view
BGP view
confederation peer-as
Use the confederation peer-ascommand to specify the sub-ASs constituting a confederation.
congestion-threshold
Use the congestion-thresholdcommand to enable congestion management function of frame relay virtual
circuit.
Frame Relay Class view
connection
Use the connectioncommand to create a CE connection.
MPLS L2VPN CE view
connection-limit default
Use the connection-limit defaultcommand to configure the action when the limit policy is not available.
System view
System view
System view
System view
connection-limit default amount
Use the connection-limit default amountcommand to set default threshold for connection limit.
connection-limit enable
Use the connection-limit enablecommand to enable the connection limit function.
connection-limit policy
Use the connection-limit policycommand to create connection limit policy and enter its view.
3Com Router 5000/6000 Family
Command Reference
17
controller cpos
Use the controller cposcommand to enter CPOS interface view.
System view
System view
controller e1
controller e3
controller t1
controller t3
copy
Use the controller e1command to enter CE1/PRI interface view.
Use the controller e3command to enter the CE3 interface view.
Use the controller t1command to enter a CT1/PRI interface view.
Use the controller t3command to enter the CT3 interface view.
Use the copycommand to copy a file.
System view
System view
System view
User view
cost-style
count
Use the cost-stylecommand to set the cost type of an IS-IS packet received/sent by the router.
Use the countcommand to configure the number of packets to be sent for each test.
IS-IS view
HWPing Test Group view
country
Use the countrycommand to specify the code of the country to which the entity belongs. It is a standard
2-byte code, e.g., CN for China.
PKI Entity view
country-code
Use the country-codecommand to configure the coding format of the modem connected to the serial
interface.
Asynchronous Serial Interface view,
AM Interface view
cptone
Use the cptonecommand to set the prompt tone played on the current voice subscriber-line to the specified
country mode.
Voice Subscriber-Line view
cpu-usage cycle
Use the cpu-usage cyclecommand to set the CPU usage statistic interval.
Use the crccommand to set the CRC length on the POS interface.
Use the crccommand to configure CRC mode of the serial interface formed by CE1.
Use the crccommand to configure CRC mode of the serial interface formed by CE3.
Use the crccommand to configure CRC mode of the serial interface formed by CT1.
Use the crccommand to configure CRC mode of the serial interface formed by CT3.
System view
crc
POS Interface view
crc
Synchronous Serial Interface view
Synchronous Serial Interface view
Synchronous Serial Interface view
Synchronous Serial Interface view
PKI Domain view
crc
crc
crc
crl check disable
Use the crl check disablecommand to disable CRL checking.
18
3Com Router 5000/6000 Family
Command Reference
crl update-period
Use the crl update-periodcommand to specify the update period of CRL, which is the interval between
local downloads of CRLs from CRL access server.
PKI Domain view
PKI Domain view
crl url
Use the crl urlcommand to specify the distribution point URL for CRL.
crp-policy
Use the crp-policycommand to restrict the range for valid C-RP and the group range served by each
C-RP, preventing C-RP cheating.
PIM view
CT3 Interface view
BGP view
ct1 alarm
Use the t1 alarmcommand to enable the specified T1 line on the CT3 interface to detect/send alarm
signals.
dampening
Use the dampeningcommand to make BGP route dampening valid or modify various BGP route dampening
parameters.
data algorithm-suite
Use the data algorithm-suitecommand to specify the algorithm suite used by IPSec SA (security
association) to forward data.
Dvpn-Policy view
data-coding (CT1/PRI Interface)
Use the data-coding normalcommand to disable user data inversion on the CT1/PRI interface.
Use the data-coding invertedcommand to enable user data inversion on the CT1/PRI interface.
CT1/PRI Interface view
data-flow-format
data-flow-format
Use the data-flow-formatcommand to configure the unit in which data flows are sent to a RADIUS Server.
Use the data-flow-formatcommand to configure the unit of data flows sent to the TACACS server.
RADIUS view
TACACS+ view
data ipsec-sa duration time-base
Use the data ipsec-sa duration time-basecommand to set the lifetime of the IPSec SA used to encrypt
DVPN data.
Dvpn-Policy view
User Interface view
databits
Use the databitscommand to set data bits on the user interface.
Use the datafillcommand to configure the data for padding test packets.
Use the datasizecommand to configure the size of test packets.
datafill
HWPing Test Group view
HWPing Test Group view
datasize
datetime local
Use the datetime localcommand to configure the Datetime information element in the Connect message
to use local time in an ISDN call.
PRI and BSV Voice Interface Voice Subscriber Line view
ddns domainname
ddns password
Use the ddns domainnamecommand to configure a domain name whose domain name-to-IP address
mapping on DNS needs update by using the service of the DDNS service provider.
DDNS Configuration view
Use the ddns passwordcommand to configure a password for accessing the DDNS service provider.
DDNS Configuration view
3Com Router 5000/6000 Family
Command Reference
19
ddns refresh
Use the ddns refreshcommand to request the DDNS service provider to notify the DNS server that the
bound IP address of the domain name specified by the ddns domainnamecommand has changed.
DDNS Configuration view
ddns server
Use the ddns-servercommand to specify a DDNS service provider and enter its view. At present, only
3322.org is available.
System view
ddns source interface
Use the ddns source-interfacecommand to configure the interface used for accessing the DDNS service
provider.
DDNS Configuration view
ddns username
Use the ddns usernamecommand to configure a user name for accessing the DDNS service provider.
DDNS Configuration view
FTP Client view
User view
debugging
Use the debuggingcommand to enable debugging.
debugging
Use the debuggingcommand to enable system debugging.
debugging l2tp
debugging arp packet
debugging aspf
debugging atm all
debugging atm error
debugging atm event
debugging atm packet
debugging bgp
Use the debugging l2tpcommand to enable L2TP debugging.
System view
User view
Use the debugging arp packetcommand to enable ARP packets debugging.
Use the debugging aspfcommand to enable ASPF debugging function.
Use the debugging atm allcommand to enable all the debugging switches of ATM.
Use the debugging atm errorcommand to enable the error debugging of ATM.
Use the debugging atm eventcommand to enable the event debugging of ATM.
Use the debugging atm packetcommand to enable the packet debugging of ATM.
Use the debugging bgpcommand to enable debugging of specified BGP packets and events.
User view
User view
User view
User view
User view
User view
debugging bgp mp-update
Use the debugging bgp mp-updatecommand to enable MBGP Update packet debugging.
User view
debugging bims all
debugging bridge
Use the debugging bims allcommand to enable BIMS debugging.
User view
Use the debugging bridgecommand to enable the debugging function of a bridge set.
User view
debugging clns clnp
Use the debugging clns clnpcommand to enable debugging for CLNS packets to display the contents of
all received/transmitted CLNP packets.
User view
20
3Com Router 5000/6000 Family
Command Reference
debugging clns echo
debugging clns rd
Use the debugging clns echocommand to enable debugging for Echo packets.
Use the debugging clns rdcommand to enable debugging for RD packets.
User view
User view
User view
User view
User view
User view
User view
User view
System view
User view
debugging clns routing
Use the debugging clns routingcommand to enable debugging for Layer 3 routing tables.
debugging connection-limit
Use the debugging connection-limitcommand to enable connection limit debugging.
debugging detect-group
Use the debugging detect-groupcommand to enable auto detect debugging.
debugging dhcp client
debugging dhcp relay
debugging dhcp server
debugging dialer
Use the debugging dhcp clientcommand to enable debugging on the DHCP client.
Use the debugging dhcp relaycommand to enable debugging on the DHCP-relay module.
Use the debugging dhcp servercommand to enable debugging on the DHCP server.
Use the debugging dialercommand to enable DCC debugging.
debugging dlsw
Use the debugging dlswcommand to enable DLSw debugging.
debugging dlsw ethernet-backup
Use the debugging dlsw ethernet-backupcommand to enable debugging for DLSw Ethernet redundancy.
User view
User view
User view
User view
User view
User view
User view
User view
debugging dlsw filter
Use the debugging dlsw filtercommand to enable debugging for DLSw filtering.
debugging dlsw packet
Use the debugging dlsw packetcommand to enable SSP packet debugging for DLSw.
debugging dlsw reachable-cache
Use the debugging dlsw reachable-cachecommand to enable DLSw reachability debugging.
debugging dlsw udp
debugging dns
Use the debugging dlsw udpcommand to enable UDP packet debugging for DLSw.
Use the debugging dnscommand to enable DNS client debugging.
Use the debugging dvpncommand to enable DVPN debugging.
debugging dvpn
debugging encrypt-card
Use the debugging encrypt-cardcommand to enable debugging on the specified or all encryption cards.
3Com Router 5000/6000 Family
Command Reference
21
debugging esis
Use the debugging esis eventcommand to enable debugging for ES-IS protocol-related events. You can
display event information using this command, such as changes of neighbor states, entries in Level 0
routing table, and interface states.
Use the debugging esis packetcommand to enable debugging for ES-IS packets. You display information
about received/transmitted ES-IS packets, such as packet size, packet type, packet HT, and Layer 2 and
Layer 3 address.
User view
User view
User view
User view
User view
debugging firewall
debugging fr
Use the debugging firewallcommand to enable the information debugging of the firewall packet filtering.
Use the debugging frcommand to enable frame relay information debugging.
debugging fr compress
Use the debugging fr compresscommand to enable FRF9 IPHC debugging of frame relay.
debugging fr compression
Use the debugging fr compression iphccommand to enable FRF20 IPHC debugging of frame relay.
debugging fr pvc-group
Use the debugging fr pvc-groupcommand to enable debugging for the specified PVC group or all PVC
groups.
User view
User view
User view
User view
User view
User view
User view
User view
debugging hdlc clns
debugging hwatacs
debugging hwping
debugging igmp
Use the debugging hdlc clnscommand to enable debugging for HDLC OSI packets.
Use the debugging hwtacacscommand to enable TACACS+ debugging.
Use the debugging hwpingcommand to enable HWPing debugging.
Use the debugging igmpcommand to enable IGMP debugging functions.
Use the debugging ikecommand to enable IKE debugging.
Use the debugging ike dpdcommand to enable IKE DPD debugging.
Use the debugging ip icmpcommand to enable the ICMP debugging.
debugging ike
debugging ike dpd
debugging ip
debugging ip count
Use the debugging ip countcommand to enable debugging for the IP Accounting module (the IP
Accounting).
User view
User view
User view
User view
debugging ip multicast-policy
Use the debugging ip multicast-policycommand to enable the debugging of IP multicast policy routing.
debugging ip netstream
Use the debugging ip netstreamcommand to enable NetStream debugging.
debugging ip urpf
Use the debugging ip urpfcommand to display the information on the rejected packets by URPF.
22
3Com Router 5000/6000 Family
Command Reference
debugging ipsec
Use the debugging ipseccommand to turn IPSec debugging on.
User view
debugging ipx packet
Use the debugging ipx packetcommand to enable IPX packet debugging switch to view the contents of
IPX packet received and transmitted.
User view
User view
User view
User view
User view
User view
debugging ipx ping
debugging ipx rip
Use the debugging ipx pingcommand to enable IPX Ping packet debugging switch to view the contents
of Ping packet received and transmitted.
Use the debugging ipx ripcommand to enable RIP debugging switch to view information on RIP packet
received and transmitted, routing changes and timer expiry.
debugging ipx rtpro-flash
Use the debugging ipx rtpro-flashcommand to turn on the debugging switch of route refreshing in the
IPXRM module.
debugging ipx rtpro-interface
Use the debugging ipx rtpro-interfacecommand to turn on the debugging switch of interface change
in the IPXRM module.
debugging ipx rtpro-routing
Use the debugging ipx rtpro-routingcommand to turn on the debugging switch of route change in the
IPXRM module.
debugging ipx sap
Use the debugging ipx sapcommand to enable IPX SAP debugging switch to view information on SAP
packet received and transmitted, routing changes and timer expiry.
User view
User view
User view
debugging isdn
debugging isis
Use the debugging isdncommand to enable ISDN debugging.
Use the debugging isiscommand to enable IS-IS debugging.
debugging isis es-adjacency
Use the debugging isis es-adjacencycommand to enable debugging for IS-IS protocol-related events
occur on neighboring ESs.
User view
debugging isis is-adjacency
Use the debugging isis is-adjacencycommand to enable debugging for IS-IS protocol-related events
occur on neighboring ISs.
User view
User view
User view
User view
debugging lapd
Use the debugging lapbcommand to enable LAPB debugging.
debugging llc2
Use the debugging llc2command to enable the LLC2 debugging.
Use the debugging llc2 packetcommand to enable U frame debugging for LLC2.
debugging llc2 packet
debugging local-server
Use the debugging local-servercommand to enable debugging for the local RADIUS authentication
server.
User view
3Com Router 5000/6000 Family
Command Reference
23
debugging mobile-ip advertise
Use the debugging mobile-ip advertisecommand to enable debugging for mobility agent
advertisements.
User view
User view
User view
User view
User view
User view
User view
User view
debugging mobile-ip mobile-router
Use the debugging mobile-ip mobile-routecommand to enable debugging for an MR.
debugging mobile-ip node
Use the debugging mobile-ip nodecommand to enable debugging for MIP packets and events.
debugging modem
Use the debugging modemcommand to enable Modem debugging.
Use the debugging mpls l2vpncommand to view L2VPN link information.
Use the debugging ldpcommand to enable debugging of LDP messages.
Use the debugging mpls lspmcommand to enable various LSP debugging.
Use the debugging msdpcommand to enable MSDP debugging functions.
debugging mpls l2vpn
debugging mpls ldp
debugging mpls lspm
debugging msdp
debugging multicast forwarding
Use the debugging multicast forwardingcommand to enable multicast packet forwarding debugging
functions.
User view
User view
debugging multicast kernel-routing
Use the debugging multicast kernel-routingcommand to enable multicast kernel routing debugging
functions.
debugging multicast status-forwarding
Use the debugging multicast status-forwardingcommand to enable multicast forwarding status
debugging functions.
User view
User view
User view
User view
User view
debugging nat
Use the debugging natcommand to enable the NAT debugging function.
Use the debugging ntp-servicecommand to enable NTP service debugging.
Use the debugging ospfcommand to enable OSPF debugging.
Use the debugging padcommand to enable PAD debugging.
debugging ntp-service
debugging ospf
debugging pad
debugging physical
Use the debugging physicalcommand to enable debugging of the physical module on the specified
interface.
User view
User view
User view
debugging pim common
debugging pim dm
Use the debugging pim commoncommand to enable common PIM debugging functions.
Use the debugging pim dmcommand to enable PIM-DM debugging functions.
24
3Com Router 5000/6000 Family
Command Reference
debugging pim sm
debugging pki
Use the debugging pim smcommand to enable PIM-SM debugging functions.
Use the debugging pkicommand to enable PKI debugging functions.
Use the debugging portal command to enable portal debugging.
User view
Any view
User view
debugging portal
debugging pos
Use the debugging pos eventcommand to enable event debugging for the POS access service.
Use the debugging pos errorcommand to enable error debugging for the POS access service.
Use the debugging pos packetcommand to enable packet debugging for the POS access service.
Use the debugging pos allcommand to enable all debugging for the POS access service.
User view
User view
debugging pos-app
Use the debugging pos-appcommand to enable debugging for the specified or all POS applications.
debugging pos-interface
Use the debugging pos-interfacecommand to enable debugging for the specified or all POS access
ports.
User view
debugging ppp { all | cbcp | ccp | scp }
Use the debugging ppp { all | cbcp | ccp | scp }command to enable PPP related cbcp, ccp, scp or
all debugging.
User view
User view
debugging ppp { chap | pap }
Use the debugging ppp { chap | pap }command to enable PPP related CHAP or PAP debugging.
debugging ppp { core | ip | ipcp | lcp | lqc | mp }
Use the debugging ppp { core | ip | ipcp | lcp | lqc | mp }command to enable PPP related core,
ip, ipcp, lcp, lqc or mp debugging.
User view
User view
debugging ppp compression iphc rtp
Use the debugging ppp compression iphc rtpcommand to view debugging information about
IP/UDP/RTP header compression in IP header compression.
debugging ppp compression iphc tcp
Use the debugging ppp compression iphc tcpcommand to view the single packet information of the
IP/TCP header compression.
User view
User view
User view
User view
User view
User view
debugging pppoe-client
The command debugging pppoe-clientis used to enable PPPoE Client debugging switch.
Use the debugging pppofrcommand to enable PPPoFR debugging.
Use the debugging qllccommand to enable QLLC debugging.
debugging pppofr
debugging qllc
debugging radius
debugging rip
Use the debugging radiuscommand to enable RADIUS debugging.
Use the debugging ripcommand to enable RIP debugging.
3Com Router 5000/6000 Family
Command Reference
25
debugging rlogin
Use the debugging rlogincommand to enable remote login (rlogin) debugging.
User view
User View
User view
User view
debugging rsh
Use the debugging rshcommand to enable RSH debugging.
debugging sdlc
debugging slip
debugging snmp-agent
Use the debugging sdlccommand to enable the SDLC debugging.
Use the debugging slipcommand to enable the debugging switch of the SLIP protocol.
Use the debugging snmp-agentcommand to enable SNMP agent debugging and specify the information
to be output.
User view
User view
User view
User view
debugging standby event
Use the debugging standby eventcommand to enable debugging of the backup center.
debugging stp
Use the debugging stpcommand to enable STP debugging.
debugging ssh client
debugging ssh server
Use the debugging ssh clientcommand to enable SSH client debugging.
Use the debugging ssh servercommand to output information such as the negotiation process regulated
by SSH1.5 protocol to information center as debugging formation and to debug a user interface separately.
User view
User view
User view
debugging tcp event
debugging tcp md5
debugging tcp packet
Use the debugging tcp eventcommand to enable TCP events debugging.
Use the debugging tcp md5command to enable the MD5 authentication debugging of the TCP connection.
Use the debugging tcp packetcommand to enable the debugging of TCP connection. The number of
debugging switches users can enable is limited, that is, at the same time only a fixed number of debugging
switches can be enabled (combination of task ID and socket ID).
User view
User view
User view
User view
User view
User view
User view
debugging telnet
Use the debugging telnetcommand to enable Telnet connection debugging.
Use the debugging tunnelcommand to enable tunnel debugging.
debugging tunnel
debugging tftp-server
debugging udp-helper
debugging udp packet
debugging voice cm
Use the debugging tftp-servercommand to enable TFTP server debugging.
Use the debugging udp-helpercommand to enable UDP Helper debugging.
Use the debugging udp packetcommand to enable the debugging of UDP connection.
Use the debugging voice cmcommand to enable debugging for CM.
26
3Com Router 5000/6000 Family
Command Reference
debugging voice data-flow
debugging voice dpl
Use the debugging voice data-flowcommand to enable debugging for voice data processes.
User view
User view
User view
Use the debugging voice dplcommand to enable the debugging of voice dial program.
debugging voice fax
debugging voice h225
Use the debugging voice faxcommand to enable fax debugging.
Use the debugging voice h225command to enable debugging for the H.225.0 negotiation messages or
events.
User view
debugging voice h245
Use the debugging voice h245command to enable debugging for the H.245 negotiation messages or
events.
User view
User view
debugging voice ipp
debugging voice r2
Use the debugging voice ippcommand to enable H.323 recommendation suite module debugging.
Use the debugging voice r2command to enable the corresponding debugging in R2 signaling module.
Use the debugging voice r2 ccbcommand to view the information of the corresponding control block by
specifying the E1 port number and time slot number.
User view
debugging voice ras
debugging voice rcv
Use the debugging voice rascommand to enable the debugging information output switch of RAS
messages interacted between GK Client and GK Server.
User view
User view
Use the debugging voice rcvcommand to enable the debugging of the RCV module.
debugging voice rcv r2
Use the debugging voice rcv r2command to enable the debugging between the RCV module and the
R2 module of bottom layer.
User view
User view
User view
User view
User view
debugging voice sip
Use the debugging voice sipcommand to enable SIP debugging.
debugging voice sip rm
Use the debugging voice sip rmcommand to enable debugging for RM module.
debugging voice sip sm
Use the debugging voice sip cmcommand to enable debugging for SM module.
debugging voice vas
Use the debugging voice vascommand to enable the VAS module debugging.
debugging voice vas fax
Use the debugging voice vas faxcommand to enable the debugging of fax data access between the VAS
module and voice card.
User view
User view
User view
debugging voice vcc
debugging voice vmib
Use the debugging voice vcccommand to enable the debugging at various levels of the VCC module.
Use the debugging voice vmibcommand to enable the voice MIB module debugging.
3Com Router 5000/6000 Family
Command Reference
27
debugging voice vofr
Use the debugging voice vofrcommand to enable VoFR module debugging.
User view
User view
debugging voice vpp
Use the debugging voice vppcommand to enable the debugging of the VPP module.
debugging voice vpp r2
Use the debugging voice vpp r2command to enable the debugging between the VPP module and the
R2 module of bottom layer.
User view
User view
User view
User view
User view
debugging vrrp
debugging vty
Use the debugging vrrpcommand to enable VRRP debugging.
Use the debugging vtycommand to enable VTY debugging.
debugging web java-blocking
Use the debugging web java-blockingcommand to enable Java blocking debugging.
debugging web url-filter host
Use the debugging web url-filter hostcommand to enable the URL address filtering debugging.
debugging web url-filter parameter
Use the debugging web url-filter parametercommand to enable the URL parameter filtering
debugging.
User view
User view
debugging x25
debugging x25 x2t
debugging x25 xot
default
Use the debugging x25command to enable X.25 debugging.
Use the debugging x25 x2tcommand to enable X2T debugging.
Use the debugging x25 xotcommand to enable XOT debugging
System view
User view
Use the defaultcommand to restore the default of all the R2 configurations and reset the R2 call statistics
to 0.
R2 CAS view
OSPF view
default cost
default-cost
Use the default costcommand to configure the default cost for OSPF to redistribute external routes.
Use the default-costcommand to configure the cost of the default route transmitted by OSPF to the STUB
or NSSA area.
OSPF Area view
RIP view
default cost
Use the default costcommand to configure the default routing cost of a redistributed route.
default entity compression
Use the default entity compressioncommand to globally configure the mode of coding and decoding
as the default value.
Voice Dial Program view
default entity fax
Use the default entity faxcommand to set the default fax parameter settings globally.
Voice Dial Program view
28
3Com Router 5000/6000 Family
Command Reference
default entity modem compatible-param
Use the default entity modem compatible-paramcommand in the case that you fail to use standard
Modem PCM to interoperate with devices from other vendors.
Voice Dial Program view
default entity modem protocol
Use the default entity modem protocolnonecommand to globally disable Modem function of voice
entity.
Use the default entity modem protocolpcmcommand to globally configure PCM Modem protocol type
of voice entity, including coding/decoding and Modem negotiation mode.
Voice Dial Program view
default entity normal-connect slow-h245
Use the default entity normal-connect slow-h245command to globally disable the calling end from
actively initiating an H245 connection request to the called end before the called end is hooked off.
Use the default entity normal-connect slow-h245command to default to globally disable the calling
end from actively initiating the H245 connection request to the called end before the called end is hooked
off. In this case, all newly created voice entities and voice entities which have not been configured with this
function will inherit this configuration.
Voice Dial Program view
default entity payload-size
Use the default entity payload-sizecommand to configure the default time length of voice packets with
different coding formats.
Voice Dial Program view
default entity service data
Use the default entity service datacommand to globally configure enabling data call service.
Voice dial program view
default entity vad-on
default interval
default limit
Use the default entity vad-oncommand to globally configure enabling silence detection as the default
value.
Voice Dial Program view
Use the default intervalcommand to configure the default interval for OSPF to redistribute external
routes.
OSPF view
OSPF view
Use the default limitcommand to configure default value of maximum number of redistributed routes.
default local-preference
Use the default local-preferencecommand to configure the local preference.
BGP Unicast view
BGP Multicast view
VPNv4 view
default med
Use the default medcommand to configure the system MED value.
BGP Unicast view
BGP Multicast view
VPNv4 view
VPN Instance view
default-route-advertise
Use the default-route-advertisecommand to configure the default route of Level-1 and Level-2 routers.
IS-IS view
default-route-advertise
Use the default-route-advertisecommand to make the system generate a default route to OSPF area.
Use the default-route-advertisecommand at ABR to generate a default route which is advertised via
the Type-5 LSA or Type-7 LSA no matter whether there is a default route in the routing table.
OSPF view
BGP view
default-route imported
Use the default-route importedcommand to redistribute local default routes into BGP.
3Com Router 5000/6000 Family
Command Reference
29
default tag
Use the default tagcommand to configure the default tag of OSPF when it redistributes an external route.
OSPF view
OSPF view
default type
Use the default typecommand to configure the default type when OSPF redistributes external routes.
delay
Use the delaycommand to configure the related time parameters at the digital E&M subscriber-line (E1
controller).
Digital E&M Voice Subscriber-Line view
delay
Use the delaycommand to configure the relevant time parameters on an FXO or analog E&M
subscriber-line.
FXO Voice Subscriber-Line view
delay-reversal
Use the delay-reversalcommand to configure the timer's interval of polarity-reverse transmission delay
on FXS interfaces.
Voice Subscriber-Line view
delete
delete
Use the deletecommand to delete the specified file.
FTP Client view
SFTP Client view
Use the deletecommand to delete the specified file from the server as you would with the remove
command.
delete
Use the deletecommand to move the specified file from the storage device to the recycle bin, where you
can completely delete the file with the undeletecommand or restore it with the reset recycle-bin
filenamecommand.
User view
System view
System view
delete rpf-route-static all
Use the delete rpf-route-static allcommand to delete all the static multicast routes.
delete static-routes all
Use the delete static-routes allcommand to cancel all the static routes.
description
Use the descriptioncommand to configure port description. Identifying a port is the only function of this
command.
Ethernet Port view
description
description
description
Use the descriptioncommand to briefly describe a test operation.
HWPing Test Group view
Interface view
Use the descriptioncommand to describe the interface.
Use the descriptioncommand to configure description information for a specified VPN instance.
Vpn-Instance view
description (in Voice Entity View)
Use the descriptioncommand to configure a voice entity description string.
Voice Entity view
description (in Voice Subscriber-Line View)
Use the descriptioncommand to configure a subscriber-line description character string.
FXO Voice Subscriber-Line view
destination
Use the destinationcommand to specify the destination IP address to be filled in the added IP header at
the time of tunnel interface encapsulation.
Tunnel Interface view
30
3Com Router 5000/6000 Family
Command Reference
destination-ip
destination-port
detect
Use the destination-ipcommand to configure the destination IP address in the test.
Use the destination-portcommand to configure the destination port in the test.
Use the detectcommand to specify ASPF policy for application layer protocols.
HWPing Test Group view
HWPing Test Group view
ASPF Policy view
detect
Use the detectcommand to enable data carrier detection as well as level detection on a serial interface.
Asynchronous Serial Interface view
Synchronous Serial Interface view,
detect-ais (CE1/PRI Interface)
Use the detect-aiscommand to enable alarm indication signal (AIS) detect on the CE1/PRI interface.
CE1/PRI Interface view
System view
detect group
Use the detect-groupcommand to create a detect group and enter its view.
detect list
Use the detect-listcommand to add an IP address to the detect group and assign the address a detecting
sequence number.
Detect Group view
IKE Proposal view
dh
Use the dhcommand to select the Diffie-Hellman group for an IKE proposal.
dhcp accounting domain (Interface view)
Use the dhcp server accounting domaincommand to enable DHCP accounting for addresses from the
interface address pool and configure a domain for DHCP accounting.
Interface view
System view
dhcp enable
Use the dhcp enablecommand to enable DHCP.
dhcp relay information
Use the dhcp relay information enablecommand to enable the DHCP relay to support option 82
globally.
System view
System view
dhcp relay information strategy
Use the dhcp relay information strategycommand to configure a strategy for handling packets with
option 82 on the DHCP relay.
dhcp relay release
Use the dhcp relay releasecommand to send an IP address releasing request to a DHCP server via the
DHCP relay.
Interface view
System view
dchp select (Interface view)
Use the dhcp selectcommand in Interface view to select a method for disposing the DHCP packets
destined to the local device.
Interface view
System view
System view
dchp select (System view)
Use the dhcp selectcommand in System view to select a method for multiple interfaces in a specified
range to dispose the DHCP packets destined to the local device.
dhcp server accounting domain interface (System view)
Use the dhcp server accounting domain interfacecommand to enable DHCP accounting for addresses
from the address pools of the specified interfaces and configure a domain for DHCP accounting.
3Com Router 5000/6000 Family
Command Reference
31
dhcp server bims-server (Interface view)
Use the dhcp server bims-servercommand to enable and configure BIMS option support on the current
interface.
Ethernet Interface (or Subinterface) view
dhcp server bims-server interface (System view)
Use the dhcp server bims-server interfacecommand to enable and configure BIMS option support for
an interface or all interfaces configured with interface address pools.
System view
System view
dhcp server detect
Use the dhcp server detectcommand to enable pseudo-DHCP-server detection.
dhcp server dns-list
Use the dhcp server dns-listcommand in interface view to configure DNS IP addresses for an interface
configured with a DHCP address pool.
Ethernet Interface (or Subinterface) view
dhcp server dns-list interface (System view)
Use the dhcp server dns-list interfacecommand to assign DNS IP addresses to the DHCP address
pool of multiple interfaces in a specified range.
System view
dhcp server domain-name (Interface view)
Use the dhcp server domain-namecommand in interface view to configure the domain name that the
DHCP address pool of the current interface allocates to clients.
Ethernet Interface (or Subinterface) view
dhcp server domain-name interface (System view)
Use the dhcp server domain-name interfacecommand in system view to configure the domain name
that the DHCP address pool of the interfaces in a specified range allocates to DHCP clients.
System view
dhcp server expired (Interface view)
Use the dhcp server expiredcommand in interface view to configure a valid period allowed for leasing IP
addresses in the current interface DHCP address pool.
Ethernet Interface (or Subinterface) view
dhcp server forbidden-ip
Use the dhcp server forbidden-ipcommand to exclude IP addresses in a specified range to participate
in the auto-allocation.
System view
System view
dhcp server interface (System view)
Use the dhcp server expired interfacecommand in system view to configure a valid period allowed for
leasing IP addresses in the interface DHCP address pool of the interfaces in a specified range.
dhcp server ip-pool
Use the dhcp server ip-poolcommand to create a DHCP address pool and access the DHCP address
pool view.
System view
dhcp server nbns-list (Interface view)
Use the dhcp server nbns-listcommand in interface view to configure NetBIOS server addresses in the
DHCP address pool of current interface.
Ethernet Interface (or Subinterface) view
dhcp server nbns-list interface (System view)
Use the dhcp server nbns-list interfacecommand in system view to configure NetBIOS server
addresses for the clients that get ip address from the DHCP address pool of the interfaces in a specified
range.
System view
dhcp server netbios-type (Interface view)
Use the dhcp server netbios-typecommand in interface view to configure the NetBIOS node type of the
DHCP clients of the current interface.
Ethernet Interface (or Subinterface) view
dhcp server netbios-type interface (System view)
Use the dhcp server netbios-type interfacecommand in system view to configure a NetBIOS node
type for the DHCP clients of the interfaces in a specified range.
System view
32
3Com Router 5000/6000 Family
Command Reference
dhcp server option (Interface view)
Use the dhcp server optioncommand in interface view to configure a DHCP self-defined option for the
DHCP address pool of the current interface.
Ethernet Interface (or Subinterface) view
dhcp server option interface (System view)
Use the dhcp server optioncommand in system view to configure a DHCP self-defined option for the
interfaces in a specified range.
System view
dhcp server ping
Use the dhcp server pingcommand to configure the maximum number of ping packets that the DHCP
server is allowed to send and the longest time period that the DHCP server should wait for the response to
each ping packet.
System view
System view
dhcp server relay information enable
Use the dhcp server relay information enablecommand to enable the DHCP server to support option
82.
dhcp server static-bind
Use the dhcp server static-bindcommand to configure a static address binding in the DHCP address
pool of the current interface.
Ethernet Interface (or Subinterface) view
Interface view
dhcp server synchronize arp (Interface view)
Use the dhcp server synchronize arpcommand to enable authorized ARP for a DHCP interface address
pool.
dhcp server synchronize arp interface (System view)
Use the dhcp server synchronize arp interfacecommand to enable authorized ARP for specified
DHCP interface address pools.
System view
dhcp server voice-config (Interface view)
Use the dhcp server voice-configcommand to enable the DHCP server to send option 184 and
suboptions of 184 when it assigns addresses from the current interface address pool.
Interface view
dhcp server voice-config interface (System view)
Use the dhcp server voice-config interfacecommand to enable the DHCP server to send option 184
and suboptions of 184 when it assigns addresses from the specified interface address pool.
System view
Voice Entity view
Voice view
dial-prefix
Use the dial-prefixcommand to configure the prefix of the telephone number dialed by the voice entity.
Use the dial-programcommand to enter the voice dial program view.
dial-program
dialer bundle
dialer bundle-member
Use the dialer bundlecommand to configure a dialer bundle used by a dialer interface.
Dialer Interface view
Use the dialer bundle-membercommand to configure a physical interface included in a dialer bundle in
the Resource-Shared DCC application.
Physical Interface view
Physical or Dialer Interface view
Physical or Dialer Interface view
dialer call-in
Use the dialer call-incommand to enable ISDN callback according to ISDN caller ID.
dialer callback-center
Use the dialer callback-centercommand to enable the callback server function.
dialer circular-group
Use the dialer circular-groupcommand to add the physical interface to a dialer circular group specified
here.
Physical Interface view
3Com Router 5000/6000 Family
Command Reference
33
dialer disconnect
Use the dialer disconnectcommand to clear the dial-up link or the session link on the specified interface
at the PPPoE/PPPoA client.
Any view
dialer enable-circular
Use the dialer enable-circularcommand to enable Circular DCC.
Physical or Dialer Interface view
dialer group
Use the dialer-groupcommand to configure access control on the packets transmitted on a DCC interface
and to place the interface in an access control group.
Physical or Dialer Interface view
dialer isdn-leased
dialer isdn-leased
Use the dialer isdn-leasedcommand to configure an ISDN B channel (can be either the channel on a
BRI or PRI interface) to be the leased line.
Physical or Dialer Interface view
Use the dialer isdn-leased 128kcommand to configure 128K leased line connection.
Use the dialer isdn-leasednumbercommand to configure 64K leased line connection.
ISDN BRI Interface view
dialer number
Use the dialer numbercommand to configure a dial number for placing a call to a single remote end.
Physical or Dialer Interface view
dialer priority
Use the dialer prioritycommand to configure a priority for a physical interface in a dialer circular group
in the Circular DCC configuration.
Physical Interface view
dialer queue-length
Use the dialer queue-lengthcommand to configure the number of packets which comply with the "permit"
statement that can be buffered before a link is set up.
Physical or Dialer Interface view
dialer route
Use the dialer routecommand to allow a DCC interface to call the specified destination address (host or
network address) or to receive calls from multiple remote ends.
Physical or Dialer Interface view
dialer-rule
Use the dialer-rulecommand to configure the conditions of the data packet that can trigger a DCC call.
System view
dialer threshold
Use the dialer thresholdcommand to configure the traffic threshold of a link on the DCC interface so that
another link can be enabled to call the same destination address when the ratio of traffic on all connected
links on the DCC interface to the available bandwidth exceeds the preset percentage.
Dialer Interface view
dialer timer autodial
Use the dialer timer autodialcommand to configure the automatic dialing interval of DCC.
Physical or Dialer Interface view
dialer timer compete
Use the dialer timer competecommand to configure an idle interval for an interface after call contention
occurs on the interface.
Physical or Dialer Interface view
dialer timer enable
Use the dialer timer enablecommand to configure an interval for the next call attempt on an interface
after the link is disconnected.
Physical or Dialer Interface view
dialer timer idle
Use the dialer timer idlecommand to configure the interval that a link is allowed to be idle (in other
words, the interval when there is no packets which comply with the “permit” statements transmitted) after a
call has been set up on the interface.
Physical or Dialer Interface view
34
3Com Router 5000/6000 Family
Command Reference
dialer timer wait-carrier
Use the dialer timer wait-carriercommand to configure the timeout time of wait-carrier timer.
Physical or Dialer Interface view
dialer timer warmup
Use the dialer timer warmupcommand to set the length of the warmup timer on the router configured with
the dial-up backup function. It is the time that the router must wait for bringing the dial-up backup function
into effect after a reboot.
System view
dialer user
Use the dialer usercommand to configure remote user name for authenticating requests when calls are
received.
Dialer Interface view
differential-delay
Use the differential-delaycommand to set the maximum differential delay for the member links in the
IMA group.
IMA Group Interface view
dir
dir
dir
Use the dircommand to query for a specified file.
FTP Client view
Use the dircommand to view the files in the specified directory as you would with the lscommand.
SFTP Client view
Use the dircommand, you can view information about the specified file or directory in the router storage
device.
User view
direct listen-port
disconnect
Use the direct listen-port Xcommand to set the listening port for vty.
Vty User Interface view
FTP Client view
Any view
Use the disconnectcommand to disconnect from the remote FTP server but remain in FTP client view.
Use the display l2tp sessioncommand to view the current L2TP sessions.
display l2tp session
display l2tp tunnel
display l2tp user
Use the display l2tp tunnelcommand to view information of the current L2TP tunnels.
Use the display l2tp usercommand to view information about the current L2TP users.
Any view
Any view
display aaa unsent-h323-call-record
Use the display aaa unsent-h323-call-recordcommand to view the detail record information about the
calls failed to be sent.
Any view
Any view
Any view
Any view
Any view
display acl
Use the display aclcommand to view the rules of access control list.
Use the display alarm urgentcommand to view the stored alarms in a specified way.
Use the display arpcommand to view the ARP mapping table.
display alarm urgent
display arp
display arp timer aging
Use the display arp timer agingcommand to display the aging timer for dynamic ARP entries.
3Com Router 5000/6000 Family
Command Reference
35
display aspf all
Use the display aspf allcommand to view the information of all ASPF policies and sessions.
Any view
Any view
Any view
Any view
display aspf interface
Use the display aspf interfacecommand to view the interface configuration of the inspection policy.
display aspf policy
display aspf session
display atm class
Use the display aspf policycommand to view the configuration of a specific inspection policy.
Use the display aspf sessioncommand to view the information of the ASPF sessions.
Use the display atm classcommand to view the information about ATM-Class. By default, if no
ATM-Class name is specified, the information of all ATM-Class is displayed.
Any view
Any view
Any view
display atm interface
display atm map-info
display atm map-info
Use the display atm map-infocommand to view the information about the upper layer protocol mapping
table of ATM.
Use the display atm map-infocommand to display upper layer protocol map information about a specified
ATM interface.
Use the display atm map-infocommand to view the information about the upper layer protocol mapping
table of ATM.
Any view
Any view
Any view
Any view
display atm pvc-group
display atm pvc-info
display auto-config
display bgp l2vpn
Use the display atm pvc-groupcommand to view the information about PVC-Group.
Use the display atm pvc-infocommand to view the information about PVC.
Use the display auto-configcommand to view the status of auto-config.
Use the display bgp l2vpn allcommand to view system operating information and all L2VPN
information.
Any view
Any view
Any view
Any view
Any view
display bgp group
Use the display bgp groupcommand to view the information of peer groups.
display bgp multicast group
Use the display bgp multicast groupcommand to view the information about peer groups.
display bgp multicast network
Use the display bgp multicast networkcommand to view the routing information that MBGP advertises.
display bgp multicast peer
Use the display bgp multicast peercommand to view information about MBGP peers.
display bgp multicast routing
Use the display bgp multicast routingcommand to view the MBGP routing information whose IP
address is specified in the BGP routing table.
Any view
36
3Com Router 5000/6000 Family
Command Reference
display bgp multicast routing as-path-acl
Use the display bgp multicast routing as-path-aclcommand to view in the BGP routing table the
MBGP routes that match the specified AS path list.
Any view
Any view
Any view
Any view
Any view
Any view
Any view
display bgp multicast routing cidr
Use the display bgp multicast routing cidrcommand to view the routing information with non-natural
network mask (that is, classless inter-domain routing, CIDR).
display bgp multicast routing community-list
Use the display bgp multicast routing community-listcommand to view the routing information that
is permitted by the MBGP community list.
display bgp multicast routing community
Use the display bgp multicast routing communitycommand to view the routing information that
belongs to the specified MBGP community.
display bgp multicast routing different-origin-as
Use the display bgp multicast routing different-origin-ascommand to view AS routes with
different origins.
display bgp multicast routing peer
Use the display multicast routing peercommand to view the route received from or sent to the
specified multicast neighbor.
display bgp multicast routing regular-expression
Use the display bgp multicast routing regular-expression command to view the routing information
matching the specified AS regular expression.
display bgp multicast routing statistic
Use the display bgp multicast routing statisticcommand to view statistics of MBGP route
information.
Any view
Any view
Any view
display bgp network
display bgp paths
display bgp peer
Use the display bgp networkcommand to view the routing information that has been configured.
Use the display bgp pathscommand to view the information about AS paths
Use the display bgp peercommand to view the information of peer.
Use the display bgp multicast peer command to view the information of MBGP peer.
Use the display bgp vpnv4 peercommand to view the information of VPN peer.
Any view
display bgp routing
Use the display bgp routingcommand to view the BGP routing information in the BGP routing table.
Use the display bgp multicast routingcommand to view the MBGP routing information in the BGP
routing table.
Use the display bgp vpnv4 routingcommand to view the VPN routing information in the BGP routing
table.
Any view
Any view
display bgp routing as-path-acl
Use the display bgp routing as-path-aclcommand to view routes that match an as-path ACL.
display bgp routing cidr
Use the display bgp routing cidrcommand to view the routing information about the non-natural mask
(namely the classless inter-domain routing, CIDR).
Any view
3Com Router 5000/6000 Family
Command Reference
37
display bgp routing community
Use the display bgp routing communitycommand to view the routing information related to the specified
BGP community number in the routing table.
Any view
display bgp routing community-list
Use the display bgp routing community-listcommand to view the routing information matching the
specified BGP community list.
Any view
Any view
display bgp routing dampened
Use the display bgp routing dampenedcommand to view BGP dampened routes.
display bgp routing different-origin-as
Use the display bgp routing different-origin-ascommand to view routes that have different source
autonomous systems.
Any view
display bgp routing flap-info
Use the display bgp routing flap-infocommand to view BGP flap statistics. When
<network-address mask> is <0.0.0.0 0.0.0.0>, this command will view the flap statistics of all BGP
routes.
Any view
Any view
Any view
Any view
Any view
display bgp routing label
Use the display bgp routing labelcommand to view routing information and label information in the
BGP routing table.
display bgp routing peer { advertised | received }
Use the display bgp routing peercommand to view the routing information the specified BGP peer
advertised or received.
display bgp routing peer dampened
Use the display bgp routing peer dampenedcommand to view the information about the dampened
routes received from the specified peer.
display bgp routing peer regular-expression
Use the display bgp routing peer regular-expression command to view the route information
received from the specified peer and matching the specified regular expression.
display bgp routing regular-expression
Use the display bgp routing regular-expression command to view the routing information matching
the specified AS regular expression.
Any view
Any view
Any view
display bgp routing statistic
Use the display bgp routing statisticcommand to display statistics about BGP routes.
Use the display bgp vpnv4command to view VPNv4 information in BGP database.
display bgp vpnv4
display bootp client
Use the display bootp clientcommand to display information about the BOOTP client, such as MAC
address and IP address.
Any view
Any view
Any view
display bridge address-table
Use the display bridge address-tablecommand to view the information of MAC address forwarding
table.
display bridge information
Use the display bridge informationcommand to view the information of one or all the enabled bridge
sets in bridge module.
38
3Com Router 5000/6000 Family
Command Reference
display bridge spanning tree
Use the display bridge spanning-treecommand to view STP state and statistics for traffic analysis and
control.
Any view
Any view
display bridge traffic
Use the display bridge trafficcommand to view the traffic statistics on an interface.
display brief interface
Use the display brief interfacecommand to display summary information about the specified or all
interfaces.
Any view
Any view
Any view
Any view
Any view
display ccc
Use the display ccccommand to view CCC connection information.
Use the display channelcommand to view the contents in an information channel.
Use the display clipboardcommand to view the contents of the clipboard.
Use the display clnscommand to display current CLNS information.
display channel
display clipboard
display clns
display clns interface
Use the display clns interfacecommand to display CLNS related information about a specified
interface.
Any view
display clns routing-table
Use the display clns routing-tablecommand to display all active CLNS routes, including those in Level
0, Level 1, and Level 2 routing tables.
Any view
Any view
Any view
Any view
display clns statistics
Use the display clns statisticcommand to display statistics information about CLNS flow.
Use the display clockcommand to display the current system time and date.
display clock
display command-alias
Use the display command-aliascommand to view the current command alias settings.
display configure-user
Use the display configure-usercommand to view information about the user who is currently authorized
to configure the equipment.
Any view
display connection
Use the display connectioncommand to view the relevant information on the specified user connection
or all the connections. The output can help you troubleshoot user connections.
Any view
Any view
Any view
display connection-limit policy
Use the display connection-limit policycommand to display connection limit policy.
display connection-limit statistics
Use the display connection-limit statisticscommand to display the connection limit statistics.
display controller cpos
Use the display controller cposcommand to view information about CPOS interfaces, such as state of
the E1/T1 channels and alarms, and errors that occur to regeneration section, multiplex section, and
higher-order path.
Any view
3Com Router 5000/6000 Family
Command Reference
39
display controller cpos e1
Use the display controller cpos e1command to view the physical layer configuration information of a
specified E1 channel on the specified CPOS interface.
Any view
display controller cpos t1
Use the display controller cpos t1command to view the physical layer configuration information of a
specified T1 channel on the specified CPOS interface.
Any view
Any view
Any view
display controller e1
display controller e3
display controller t1
Use the display controller e1command to display the information related to a CE1/PRI interface.
Use the display controller e3command to view state information on a CE3 interface.
Use the display controller t1command to display the information about the specified CT1/PRI
interface.
Any view
Any view
Any view
display controller t3
display cpu-usage
Use the display controller t3command to view state about a CT3 interface.
Use the display cpu-usagecommand to view statistics about CPU usage.
display cpu-usage history
Use the display cpu-usage historycommand to view in graphics the CPU usage statistic history of the
entire system, the specified task, or the interface board in the specified slot.
Any view
Any view
Any view
display current-configuration
Use the display current-configurationcommand to view the running configurations on the router.
Use the display debuggingcommand to view the enabled debugging switches.
display debugging
display debugging ospf
Use the display debugging ospfcommand to view the state of the debug switches for each OSPF
process.
Any view
Any view
display detect group
Use the display detect-groupcommand to display configuration information about a specified detect
group or all detect groups.
display device
Use the display devicecommand to view information on the hardware configurations of the system,
including in-position state of the RPU, NPU, interface cards, power module, and fan module, the operating
state of the interface cards, power module, and fan module, as well as the offline state of RPU and NPU.
Any view
display dhcp client
Use the display dhcp clientcommand to display the statistic information of the DHCP client. Executing
the command attached without the keyword parameter verbose will display only the brief address allocation
information on the DHCP client.
Any view
Any view
Any view
display dhcp relay address
Use the display dhcp relay addresscommand to view the DHCP relay address configuration of an
interface.
display dhcprelay-security
Use the display dhcprelay-securitycommand to display the IP-to-MAC mappings of the clients
obtaining IP addresses dynamically through the DHCP relay.
40
3Com Router 5000/6000 Family
Command Reference
display dhcp relay statistics
Use the display dhcp relay statisticscommand to view the statistics of DHCP relay in packet errors,
DHCP packets received from clients, DHCP packets received from and sent to servers, and DHCP packets
sent to clients (including unicast and broadcast packets).
Any view
Any view
Any view
Any view
Any view
display dhcp server conflict
Use the display dhcp server conflictcommand to view the DHCP address conflict statistics, including
the information in conflicted IP address, conflict detection type, and conflict time.
display dhcp server expired
Use the display dhcp server expiredcommand to view the expired address leases in a DHCP address
pool. In certain conditions, the addresses of the expired leases will be allocated to other DHCP clients.
display dhcp server free-ip
Use the display dhcp server free-ipcommand to view the free address ranges in DHCP address pools,
that is, information about IP addresses that have not been allocated yet.
display dhcp server ip-in-use
Use the display dhcp server ip-in-usecommand to view the address binding information of DHCP
clients, such as the information in hardware address, IP address, and address lease expiration.
display dhcp server statistics
Use the display dhcp server statisticscommand to view the statistics on the DHCP server, including
such information as number of DHCP address pools, automatically or manually bound address and expired
addresses, number of unknown packets, number of DHCP request packets, and number of response
packets.
Any view
Any view
display dhcp server tree
Use the display dhcp server treecommand to view the tree-structure information of DHCP address
pools, including the address pool at each node, option, address lease period, and DNS server information.
display diagnostic-information
Use the display diagnostic-informationcommand to view the operating information about the active
modules in the system.
Any view
Any view
Any view
Any view
display dialer
Use the display dialercommand to view information on DCC interfaces.
display dlsw bridge-entry
Use the display dlsw bridge-entrycommand to view the bridge-set information.
display dlsw circuits
Use the display dlsw circuitscommand to view the DLSw virtual circuits.
display dlsw ethernet-backup map
Use the display dlsw ethernet-backup mapcommand to display information about address translation
after you configure the Ethernet switch support feature.
Any view
Any view
display dlsw ethernet-backup neighbour
Use the display dlsw ethernet-backup neighbourcommand to display all neighbors of the current
router.
display dlsw information
Use the display dlsw informationcommand to view the DLSw exchange capability information. The
output information of the command facilitates the user to understand the status of the DLSw virtual circuit
and perform fault diagnosis.
Any view
Any view
display dlsw information
Use the display dlsw informationcommand to display DLSw capability exchange information. The
output of this command can help you understand the status of DLSw virtual circuits.
3Com Router 5000/6000 Family
Command Reference
41
display dlsw reachable-cache
Use the display dlsw reachable-cachecommand to view the reachable-cache of DLSw.
Any view
Any view
Any view
Any view
display dlsw remote
display dlsw remote
display dns domain
Use the display dlsw remotecommand to view the information of the remote peers.
Use the display dlsw remotecommand to display information about the specified or all remote peers.
Use the display dns domaincommand to view the DNS domain names that are manually configured.
display dns dynamic host
Use the display dns dynamic-hostcommand to view the current contents in the domain name cache of
the DNS client.
Any view
Any view
display dns server
display domain
Use the display dns servercommand to view the DNS server addresses manually configured.
Use the display domaincommand to view the configuration of a specified ISP domain or display the
summary information of all ISP domains.
Any view
Any view
Any view
Any view
Any view
Any view
Any view
display dsl configuration
Use the display dsl configurationcommand to view the actual ADSL configurations.
display dsl configuration
Use the display dsl configurationcommand to view the actual DSL configurations.
display dsl status
display dsl status
display dsl version
display dsl version
display dvpn info
Use the display dsl statuscommand to view the DSL state information.
Use the display dsl statuscommand to view state about the specified DSL interface.
Use the display dsl versioncommand to view DSL version and the available capabilities.
Use the display dsl versioncommand to view the DSL version and the available functionality.
Use the display dvpn infocommand to display the configuration and operating information about a
specified DVPN.
Any view
Any view
display dvpn ipsec-sa
Use the display dvpn ipsec-sacommand to display the specified IPSec SA information.
display dvpn map
Use the display dvpn mapcommand to display information about maps in a DVPN domain, such as private
IP address, public IP address, port number, DVPN connection state, DVPN connection type, and control ID.
Any view
Any view
Any view
display dvpn online-user
Use the display dvpn online-usercommand to display the information about online DVPN users.
display dvpn session
Use the display dvpn sessioncommand to display information about sessions the device owns.
42
3Com Router 5000/6000 Family
Command Reference
display encrypt-card fast-switch
Use the display encrypt-card fast-switchcommand to view the entries in the fast forwarding cache for
the encryption cards.
Any view
Any view
display encrypt-card sa
Use the display encrypt-card sacommand to view SA information.
display encrypt-card statistics
Use the display encrypt-card statisticscommand to view statistics on the specified or all encryption
cards.
Any view
Any view
display encrypt-card syslog
Use the display encrypt-card syslogcommand to view the current system log on the encryption cards.
display environment
Use the display environmentcommand to view the current values and the thresholds of the hardware
system environment.
Any view
Any view
Any view
display esis
Use the display esiscommand to display current ES-IS protocol state, such as the configuration timer
(CT) to send ISH packets, the holding time (HT) of the information ISH packets carry.
display esis interface
Use the display esis interfacecommand to display ES-IS related information about a specified
interface.
display esis peer
Use the display esis peercommand to display information about the neighbors dynamically discovered
by ES-IS protocol (including dynamic ES and IS neighbors).
Any view
Any view
display esis statistics
Use the display esis statisticcommand to display statistics information about ES-IS flow.
display fcm
Use the display fcmcommand to display the count of dial-up negotiation failures and the count of
disconnections upon transaction timeouts for FCM module interfaces.
Any view
display fe1 serial
Use the display fe1 serialcommand to view the configuration and state about the specified or all E1-F
interfaces.
Any view
Any view
Any view
display fib
Use the display fibcommand to view the summary of the Forwarding Information Base.
Use the display fib aclcommand to filter and display FIB information.
display fib acl
display fib begin
Use the display fibcommand to output the lines related to the line containing the character string text in
the buffer according to the regular expression.
Use the display fib | begintext command to view the lines beginning from the line containing the
character string text to the end line of the buffer.
Use the display fib | includetext command to just view the lines containing the character string text.
Use the display fib | excludetext command to view the lines not containing the character string text.
Any view
Any view
display fib ip-prefix
Use the display fib ip-prefixcommand to filter and display FIB information by prefix-list name in certain
format.
3Com Router 5000/6000 Family
Command Reference
43
display fib longer
Use the display fib longercommand to display the FIB table entries matching the destination address.
Different parameters selected leads to different matching methods.
Use the display fibcommand to display the FIB table entries whose destination address ranges from
dest-addr1 dest-mask1 to dest-addr2 dest-mask2, including the FIB entries exactly matching dest-addr1
dest-mask1 and dest-addr2 dest-mask2.
Any view
Any view
display fib statistics
Use the display fib statisticscommand to display the total numbers of FIB table entries.
display firewall ethernet-frame-filter
Use the display firewall ethernet-frame-filtercommand to view the filtering statistics by ACL on the
interface, namely, the detailed filtering information based on the ACL configured via the firewall
ethernet-frame-filter { acl-number| acl-name} { inbound | outbound } command.
Any view
Any view
display firewall-statistics
Use the display firewall-statistics command to view the firewall statistics.
display fr class-map
Use the display fr class-mapcommand to view information on frame relay class to interface map,
including DLCIs of interfaces, subinterfaces on the interfaces and their DLCIs.
Any view
Any view
Any view
display fr compress
display fr del
Use the display fr compresscommand to view the statistics information of the frame relay compression.
Use the display fr delcommand to view the contents in the specified or all DE rule lists.
display fr dlci-switch
Use the display fr dlci-switchcommand to view the information of the configured FR switching to check
if the frame relay switching of a user is correctly configured.
Any view
Any view
display fr fragment-info
Use the display fr fragment-infocommand to view the frame relay fragment information.
display fr inarp-info
Use the display fr inarp-infocommand to view statistics about frame relay inverse ARP (INARP)
packets, including requests and replies.
Any view
Any view
Any view
Any view
Any view
display fr interface
display fr lmi-info
display fr map-info
display fr map-info
display fr pvc-group
Use the display fr interfacecommand to view frame relay state on the specified or all interfaces.
Use the display fr lmi-infocommand to view the statistics of LMI protocol frame.
Use the display fr map-infocommand to display frame relay (FR) address map information.
Use the display fr map-infocommand to view all FR address maps or the one for the specified interface.
Use the display fr pvc-groupcommand to view status, name, backup, protection, and other information
about the specified PVC group, PVC groups on a specified interface, or all PVC groups if no argument is
specified.
Any view
Any view
display fr map-info pppofr
Use the display fr map-info pppofr command to display information about the current PPPoFR map
and its state.
44
3Com Router 5000/6000 Family
Command Reference
display fr pvc-infoc
Use the display fr pvc-infocommand to view the frame relay PVC table.
Any view
display fr statistics
Use the display fr statisticscommand to view the current Frame Relay statistics about receiving and
sending packets.
Any view
display fr switch-table
Use the display mfrcommand to view configuration and status information of the frame relay route to
confirm the correctness of the configuration.
Any view
Any view
Any view
Any view
display fr vofr-info
display ft 1 serial
display ftp-server
Use the display fr vofr-infocommand to view the VoFR information.
Use the display ft1 serialcommand to view the configuration and state of the T1-F interface.
Use the display ftp-server command to view the parameters of the current FTP server.
display ftp-server source-ip
Use the display ftp-server source-ipcommand to display the source IP address configured for the FTP
server.
Any view
Any view
Any view
Any view
display ftp source-ip
Use the display ftp source-ipcommand to display the source IP address configured for the FTP client.
Use the display ftp-usercommand to view the parameters of the current FTP users.
display ftp-user
display history-command
Use the display history-commandcommand to view the history commands.
display hwatacs
display hwping
Use the display hwtacacscommand to view configuration information of specified or all TACACS+
schemes.
Any view
Any view
Any view
Any view
Any view
Use the display hwpingcommand, you can view test result(s).
display hwping statistics
Use the display hwping statisticscommand to view test statistics.
display icmp statistics
Use the display icmp statisticscommand to view statistics about ICMP messages.
display igmp group
Use the display igmp groupcommand to view the member information of the IGMP multicast group.
display igmp interface
Use the display igmp interfacecommand to view the IGMP configuration and running information on an
interface.
Any view
Any view
display igmp local
Use the display igmp localcommand to view the IGMP configuration and running information of the local
interface which receives and sends multicast data.
3Com Router 5000/6000 Family
Command Reference
45
display ike dpd
Use the display ike dpdcommand to display the configuration of the specified or all DPD structures about
reference count, interval-time, and time_out.
Any view
Any view
Any view
Any view
Any view
display ike peer
display ike proposal
display ike sa
Use the display ike peercommand to view the configuration about the specified or all IKE peers.
Use the display ike proposalcommand to view the parameters configured for each IKE proposal.
Use the display ike sacommand to view the current security tunnels established by IKE.
Use the display info-centercommand to view all the information recorded in the info-center.
display info-center
display interface
Use the display interfacecommand to view the LAPB or X.25 interface information. After configuring
PVC of X.25, users can use the command to obtain the status information on one interface.
Any view
Any view
display interface
display interface
Use the display interfacecommand to view configuration information on the port.
Use the display interfacecommand to view the current running state and other information about an
interface.
Any view
display interface atm
Use the display interface atmcommand to display the configuration and state information about the
specified or all ATM interfaces.
Any view
Any view
display interface bri
Use the display interface bricommand to view status about the specified ISDN BRI interface.
display interface encrypt
Use the display interface encryptcommand to view information about interfaces on the specified or all
encryption cards.
Any view
Any view
Any view
Any view
Any view
Any view
display interface {Ethernet Gigabithernet}
Use the display interface{ ethernet | gigabitethernet }command to view information about
Ethernet interfaces, such as their configurations and current running state.
display interface ima-group
Use the display interface ima-groupcommand to view the configuration and state information about
the specified or all IMA group interfaces.
display interface loopback
Use the display interface loopbackcommand to view state about the specified or all created loopback
interfaces.
display interface mfr
Use the display interface mfrcommand to view information on one or all MFR interfaces, including
configuration, state, and packet statistics.
display interface mp-group
Use the display interface mp-groupcommand to view the state about the specified or all MP-group
interfaces.
46
3Com Router 5000/6000 Family
Command Reference
display interface null
Use the display interface nullcommand to view the state about the null interface.
Any view
display interface pos
Use the display interface poscommand to view the configuration and state information of one or all POS
interfaces.
Any view
Any view
display interface tunnel
Use the display interface tunnelcommand to view the working status of tunnel interface.
display interface virtual-ethernet
Use the display interface virtual-ethernetcommand to view the state about of the specified or all
virtual Ethernet interfaces.
Any view
display interface virtual-template
Use the display interface virtual-templatecommand to view the state about the specified or all virtual
templates.
Any view
Any view
Any view
display ip count
Use the display ip countcommand to display IP packet statistics gathered by the IP Accounting.
Use the display ip count rulecommand to display IP accounting rules.
display ip count rule
display ip fast-forwarding cache
Use the display ip fast-forwarding cache command to view information on the unicast fast forwarding
table.
Any view
Any view
display ip host
Use the display ip hostcommand to display all the host names and their corresponding IP addresses.
display ip interface
Use the display ip interfacecommand to view IP-related information about the specified or all
interfaces.
Any view
display ip interface brief
Use the display ip interface briefcommand to view IP-related summary about the specified or all
interfaces.
Any view
Any view
display ip ip-prefix
Use the display ip ip-prefixcommand to view the address prefix list.
display ip multicast-fast-forwarding cache
Use the display ip multicast-fast-forwarding cache command to display summary information about
the fast forwarding table entries in the multicast fast forwarding cache.
Any view
Any view
display ip multicast-policy
Use the display ip multicast-policycommand to view the multicast policy routing information.
display ip netstream cache
Use the display ip netstream cachecommand to view configuration and status information about the
NetStream cache.
Any view
Any view
display ip netstream export
Use the display ip netstream exportcommand to view statistics about exported NetStream UDP
packets.
3Com Router 5000/6000 Family
Command Reference
47
display ip policy
Use the display ip policycommand to view the routing policies of local and configured interface policy
routings.
Any view
Any view
Any view
Any view
display ip policy setup
Use the display ip policy setupcommand to view the setting information of policy routings.
display ip policy statistic
Use the display ip policy statisticcommand to view the statistics of policy routings.
display ip routing-table
Use the display ip routing-tablecommand to view the routing table summary.
display ip routing-table acl
Use the display ip routing-table aclcommand to view the route filtered through specified basic access
control list (ACL).
Any view
Any view
Any view
Any view
Any view
display ip routing-table ip_address
Use the display ip routing-tableip_addresscommand to view the routing information of the specified
destination address.
display ip routing-table ip_address1 ip_address2
Use the display ip routing-tableip_address1 ip_address2command to view the routing
information in the specified destination address range.
display ip routing-table ip-prefix
Use the display ip routing-table ip-prefixcommand to view the route that passed the filtering rule
according to the specified ip prefix list.
display ip routing-table protocol
Use the display ip routing-table protocolcommand to view the routing information of specified
protocol.
display ip routing-table radix
Use the display ip routing-table radixcommand to view the routing table information in a tree
structure.
Any view
Any view
Any view
display ip routing-table statistics
Use the display ip routing-table statistics command to view the integrated routing information.
display ip routing-table verbose
Use the display ip routing-table verbosecommand to view the verbose routing table information.
display ip routing-table vpn-instance
Use the display ip routing-table vpn-instancecommand to view RIP information associated with vpn
instance address family.
Any view
display ip routing-table vpn-instance
Use the display ip routing-table vpn-instancecommand to view the specified information in the IP
routing table of vpn-instance.
Any view
Any view
display ip socket
Use the display ip socketcommand to display the information about all sockets in the current system.
display ip statistics
Use the display ip statisticscommand to view IP traffic statistics information. This command is used
to display such statistics information as IP packet transmit/receive, packet assembly/disassembly, which is
helpful to fault diagnosis.
Any view
48
3Com Router 5000/6000 Family
Command Reference
display ip vpn-instance
Use the display ip vpn-instancecommand to view the information related to vpn-instance, such as RD,
description, and interfaces of the VPN instance.
Any view
Any view
Any view
Any view
Any view
display ipsec policy
Use the display ipsec policycommand to view information about the ipsec policy.
display ipsec policy-template
Use the display ipsec policy-templatecommand to view information about the ipsec policy template.
display ipsec proposal
Use the display ipsec proposalcommand to view information about the proposal.
display ipsec sa
Use the display ipsec sacommand to view the relevant information about the SA.
display ipsec statistics
Use the display ipsec statisticscommand to view the IPSec packet statistics information, including
the input and output security packet statistics, bytes, number of packets discarded and detailed description
of discarded packets.
Any view
Any view
display ipx interface
Use the display ipx interface command to view IPX interface configuration information and interface
parameters in communication devices.
display ipx routing-table
Use the display ipx routing-tablecommand to view active IPX routing information.
Use the display ipx routing-table verbosecommand to view detailed IPX routing information, including
active and inactive routes.
Use the display ipx routing-table networkcommand to view active IPX routing information to specified
destination network ID.
Use the display ipx routing-table network verbosecommand to view detailed IPX routing information
to specified destination network ID, including active and inactive routes.
Use the display ipx routing-table protocol { rip | static | default | direct } command to view IPX routing
information for specified destination type, including active and inactive routes.
Use the display ipx routing-table protocol{ rip | static | default | direct } verbosecommand to view
detailed IPX routing information for specified destination type, including active and inactive routes.
Any view
Any view
display ipx routing-table statistics
Use the display ipx routing-table statisticscommand to view IPX routing statistics.
display ipx service-table
Use the display ipx service-tablecommand to view contents of IPX service information table. The
output information of the command helps users with IPX SAP troubleshooting.
Any view
display ipx statistics
Use the display ipx statisticscommand to view statistics and type of IPX packet transmitted and
received.
Any view
Any view
Any view
Any view
display isdn active-channel
Use the display isdn active-channelcommand to view the active call information on ISDN interfaces.
display isdn call-info
Use the display isdn call-infocommand to view the current states of ISDN interfaces.
display isdn call-record
Use the display isdn call-recordcommand to view the information of ISDN call history.
3Com Router 5000/6000 Family
Command Reference
49
display isdn parameters
Use the display isdn parameterscommand to view the system parameters at layers 2 and 3 of the ISDN
protocol, such as the durations of system timers and frame size.
Any view
display isdn spid
display isis brief
Use the display isdn spidcommand to view information on SPID on the BRI interface encapsulated with
the NI protocol.
Any view
Any view
Any view
Any view
Any view
Any view
Any view
Use the display isis briefcommand to view the brief information of IS-IS.
display isis interface
Use the display isis interfacecommand to view the information of the IS-IS enabled interface.
display isis lsdb
Use the display isis lsdbcommand to view the link state database of the IS-IS.
display isis mesh-group
Use the display isis mesh-groupcommand to view the IS-IS mesh group.
display isis peer
Use the display isis peercommand to view IS-IS peer information.
Use the display isis routingcommand to view IS-IS routing information
display isis routing
display isis routing clns
Use the display isis routing clnscommand to display CLNS routing information generated by IS-IS
protocol.
Any view
Any view
Any view
display isis spf-log
display llc2
Use the display isis spf-logcommand to view the SPF calculation log of the IS-IS.
Use the display llc2command to view statistical information of LLC2.
display loadsharing ip address
Use the display loadsharing ip addresscommand to view the statistics about the unbalanced load
sharing based on interface bandwidth, including the number and ratio of the packets sent from the interfaces
related to the equal-cost routes to a network address.
Any view
Any view
display local-server statistics
Use the display local-server statisticscommand to display statistics of the local RADIUS
authentication server.
display local-user
Use the display local-usercommand to view the relevant information on the specified local user or all
the local users. The output can help you troubleshoot faults related to local user.
Any view
User view
Any view
Any view
display log startup
display logbuffer
Use the display log startupcommand to display the state of the configuration restoration log switch.
Use the display logbuffercommand to view the information recorded in the log buffer.
display logbuffer summary
Use the display logbuffer summarycommand to display a summary about the log buffer on the router.
50
3Com Router 5000/6000 Family
Command Reference
display mac-address
Use the display mac-addresscommand to display information about MAC address entries of an interface
or about all MAC address entries.
Any view
Any view
display memory
display memory
Use the display memorycommand to view information on system memory load.
Use the display memorycommand to view the memory setting and state information related to the routing
capacity.
Any view
display mfr
Use the display mfrcommand to view configuration and statistics information of multilink frame relay
bundle and bundle link. If no bundle or bundle link is specified, information of all bundles and bundle links
will be displayed.
Any view
Any view
display mirror
Use the display mirrorcommand to display information about port mirroring configuration, information
including the monitored ports, the direction of monitored packets and monitoring port.
display mobile-ip binding
Use the display mobile-ip bindingcommand to display information about the HA binding table. A
binding table maintains mainly the corresponding relations between HA addresses and the care-of
addresses of MNs. An HA updates the binding table based on MN registration events.
Any view
Any view
display mobile-ip globals
Use the display mobile-ip globalscommand to display global information about mobility agents.
display mobile-ip interface
Use the display mobile-ip interfacecommand to display the MIP information of an interface. With the
interface-numberargument not specified, MIP information of all interfaces is displayed.
Any view
display mobile-ip irdp
Use the display mobile-ip irdpcommand to display ICMP router discovery protocol (IRDP) configuration
information, including the agent advertisement lifetime, the maximum and minimum agent advertisement
interval, and the agent advertisement transmission mode (broadcast or multicast).
Any view
Any view
Any view
display mobile-ip mobile-router
Use the display mobile-ip mobile-routercommand to display information about an MR, including basic
information, discovered mobility agent information, registration information, and statistics.
display mobile-ip node
Use the display mobile-ip nodecommand to display information about MNs. With no parameters
specified, information about all MNs is displayed.
display mobile-ip secure
Use the display mobile-ip securecommand to display mobility security association attributes. If not
specify argument ip-address, information about all mobility security association attributes of the specified
mobility security associations is displayed.
Any view
Any view
display mobile-ip statistics
Use the display mobile-ip statisticscommand to display statistics collected by the mobility agents.
display mobile-ip violation
Use the display mobile-ip violationcommand to display MN security exception information logged by
a mobility agent. With the ip-address argument not specified, all security exception information is displayed;
up to 100 latest entries of information can be displayed.
Any view
3Com Router 5000/6000 Family
Command Reference
51
display mobile-ip visitor
Use the display mobile-ip visitorcommand to display information in the visitor table and pending table
of an FA. An FA updates its visitor table and pending table based on registration events of MNs. If not
specify the ip-addressargument, all contents of the tables are displayed.
Any view
Any view
display mpls l2vc
Use the display mpls l2vccommand to view the VC information in LDP.
display mpls l2vpn forwarding-info
Use the display mpls l2vpn forwarding-infocommand to view the L2VPN information of a specific
interface.
Any view
Any view
display mpls l3vpn-lsp
Use the display mpls l3vpn-lspcommand to view the information of vpn-instance of MPLS L3VPN LSPs.
display mpls cell-transfer interface
Use the display mpls cell-transfer interfacecommand to view statistics for cells received and sent
in a packet on an interface in transparent transmission mode.
Any view
Any view
Any view
Any view
Any view
Any view
Any view
Any view
Any view
Any view
Any view
display mpls interface
Use the display mpls interfacecommand to view all MPLS-enabled interfaces.
Use the display mpls ldpcommand to view LDP and LSR information.
display mpls ldp
display mpls ldp buffer-info
Use the display mpls ldp buffer-infocommand to view the buffer information of LDP.
display mpls ldp interface
Use the display mpls ldp interfacecommand to view the information of an LDP-enabled interface.
display mpls ldp lsp
display mpls ldp peer
Use the display mpls ldp lspcommand to view relevant LSP information created via LDP.
Use the display mpls ldp peercommand to view peer information.
display mpls ldp remote
Use the display mpls ldp remotecommand to view the configured remote peer information.
display mpls ldp session
Use the display mpls ldp sessioncommand to display the session between peer entities.
display mpls lsp
Use the display mpls lspcommand to view LSP information.
display mpls static-lsp
Use the display mpls static-lspcommand to view the information of all or one static LSP(s).
display mpls statistics
Use the display mpls statisticscommand to view statistics of all or one LSP(s) and LSP statistics on
all or one interface(s).
Any view
Any view
Any view
display msdp brief
Use the display msdp briefcommand to view the state of MSDP peer.
display msdp peer-status
Use the display msdp peer-statuscommand to view the detailed information of MSDP peer.
52
3Com Router 5000/6000 Family
Command Reference
display msdp sa-cache
display msdp sa-count
Use the display msdp sa-cachecommand to view (S, G) state learnt from MSDP peer.
Any view
Use the display msdp sa-countcommand to view the number of sources and groups in MSDP cache.
Any view
display multicast forwarding-table
Use the display multicast forwarding-tablecommand to view the information of multicast forwarding
table.
Any view
Any view
display multicast routing-table
Use the display multicast routing-tablecommand to view the information of IP multicast routing table.
display multicast routing-table static
Use the display multicast routing-table staticcommand to view the configuration information of
static multicast route.
Any view
Any view
display multicast routing-table static
Use the display multicast routing-table staticcommand to view the active multicast static routes.
display multicast routing-table static config
Use the display multicast routing-table static configcommand to view multicast static routes
configured.
Any view
display multicast rpf-info
Use the display multicast rpf-infocommand to view the Reverse Path Forwarding (RPF) routing
information for specified multicast source.
Any view
Any view
Any view
display nat
Use the display natcommand to display the configuration of address translation.
display nat connection-limit
Use the display nat connection-limitcommand to display the NAT-related connection limit statistics.
display ntp-service sessions
Use the display ntp-service sessionscommand to view brief information about all sessions maintained
by the NTP at the local device.
Any view
Any view
display ntp-service status
Use the display ntp-service statuscommand to view status about the NTP service.
display ntp-service trace
Use the display ntp-service trace command to view the summary about each NTP time server from
the local device back to the reference clock source.
Any view
Any view
display osm status slot
Use the display osm status slot slotnumcommand to view the information about the OSM board in the
specified slot, including name of the board, board status, OS name, OS version and running time of OS.
display ospf abr-asbr
Use the display ospf abr-asbrcommand to view information on the routes to the Area Border Router
(ABR) and Autonomous System Border Router (ASBR) of OSPF.
Any view
Any view
Any view
display ospf asbr-summary
Use the display ospf asbr-summarycommand to view summary about the redistributed routes of OSPF.
display ospf brief
Use the display ospf briefcommand to view the summary of OSPF.
3Com Router 5000/6000 Family
Command Reference
53
display ospf cumulative
Use the display ospf cumulativecommand to view the OSPF cumulative information.
Any view
Any view
Any view
Any view
Any view
Any view
display ospf error
Use the display ospf errorcommand to view the statistics of error information which OSPF received.
display ospf interface
Use the display ospf interfacecommand to view the OSPF interface information.
display ospf lsdb
display ospf memory
display ospf nexthop
display ospf peer
Use the display ospf lsdbcommand to view the database information about OSPF connecting state.
Use the display ospf memorycommand to view memory occupation status for LSAs.
Use the display ospf nexthopcommand to view the information about the next-hop
Use the display ospf peercommand to view the information about the neighbors in OSPF areas.
Use the display ospf peer briefcommand to view the brief information of neighbors in OSPF, mainly
the neighbor number at all states in every area.
Any view
Any view
display ospf request-queue
Use the display ospf request-queuecommand to view the information about the OSPF request-queue.
display ospf retrans-queue
Use the display ospf retrans-queuecommand to view the information about the OSPF retransmission
queue.
Any view
Any view
Any view
Any view
Any view
Any view
Any view
Any view
display ospf routing
Use the display ospf routingcommand to view the information about OSPF routing table.
display ospf sham-link
Use the display ospf sham-linkcommand to view the information of sham links.
display ospf vlink
display pim bsr-info
display pim interface
display pim neighbor
Use the display ospf vlinkcommand to view the information about OSPF virtual links.
Use the display pim bsr-infocommand to view Bootstrap Router (BSR) information.
Use the display pim interfacecommand to view the PIM interface information.
Use the display pim neighborcommand to view the PIM neighbor information.
display pim routing-table
Use the display pim routing-tablecommand to view the contents of the PIM multicast routing table.
display pim rp-info
Use the display pim rp-infocommand to view the corresponding RP information of multicast group, BSR
and static RP information.
Any view
Any view
display pki certificate
Use the display pki certificatecommand to display and browse through the certificate.
54
3Com Router 5000/6000 Family
Command Reference
display pki crl
display port
Use the display pki crlcommand to display and browse through the locally saved CRL.
Any view
Use the display portcommand to check whether the current system has hybrid or trunk ports. If there is
any, its port name is displayed.
Any view
Any view
Any view
display port-mapping
display portal
Use the display port-mappingcommand to view PAM information.
Use the display portalcommand to display the information about portal servers.
display portal update-resource
Use the display portal update-resourcecommand to display information about the update resources
configured by the user.
Any view
Any view
Any view
display pos-app
Use the display pos-appcommand to display brief information about POS applications.
Use the display pos-interfacecommand to display brief information about POS access ports.
display pos-interface
display ppp compression iphc rtp
Use the display ppp compression iphc rtpcommand to view the statistic information of the RTP header
compression.
Any view
Any view
display ppp compression iphc tcp
Use the display ppp compression iphc tcpcommand to view the statistic information of the TCP header
compression.
display ppp compression stac-lzs
Use the display ppp compression stac-lzscommand to view information about STAC-LZS
compression.
Any view
Any view
Any view
display ppp mp
Use the display pppmpcommand to view all interface information and statistics of MP.
display pppoe-server session
Use the display pppoe-server sessioncommand to view the status and statistics of PPPoE session.
display pppoe-server session
The command display pppoe-client sessionis used to display the status and statistics of PPPoE
session.
Any view
Any view
display protocol-priority
Use the display protocol-prioritycommand to view protocol priorities.
display qos car interface
Use the display qos car interface command to view parameter configuration and running statistics of
CAR at each or all interfaces.
Any view
Any view
display qos carl
Use the display qos carlcommand to view a certain rule or all the rules of CARL.
display qos cbq interface
Use the display qos cbq interfacecommand to view CBQ configuration information and operating
status, the specified PVC on specified ATM interface or on all interfaces.
Any view
3Com Router 5000/6000 Family
Command Reference
55
display qos cq interface
Use the display qos cq interfacecommand to view configuration and statistics of customized queues
(CQ) at interfaces.
Any view
Any view
display qos cql
Use the display qos cqlcommand to view contents of customized queue lists (CPL).
display qos gts interface
Use the display qos gts interfacecommand to view GTS configuration and accounting information of
certain interface or all interfaces.
Any view
Any view
display qos lr interface
Use the display qos lr interfacecommand to view LR configuration and statistics of an interface.
display qos policy
Use the display qos policycommand to display the configuration information of the specified class or all
the classes and associated behaviors in the specified policy or all policies.
Any view
Any view
display qos policy interface
Use the display qos policy interface command to view information about CBQ application on the
interface.
display qos policy interface
Use the display qos policy interfacecommand to view the configuration and operating state about the
policy on the specified interface, on the specified PVC on a particular ATM interface or on all interfaces and
PVCs.
Any view
display qos pq interface
Use the display qos pq interfacecommand to view the configuration and statistics of priority queues
(PQ) at interfaces.
Any view
Any view
display qos pql
Use the display qos pqlcommand to view contents of priority queue lists (PQL).
display qos rtpq interface
Use the display qos rtpq interfacecommand to view information of the current IP RTP Priority queue,
including the current RTP queue depth and number of RTP packets dropped, and display the RTP priority
queue configuration and statistics on an interface or on all interfaces.
Any view
Any view
Any view
Any view
display qos wfq interface
Use the display qos wfq interfacecommand to view WFQ (weighted fair queuing) configuration and
statistics of an interface.
display qos wred interface
Use the display qos wred interfacecommand to view WRED (weighed random early detection)
configuration and statistics of an interface.
display radius
Use the display radiuscommand to view the configuration information about the specified or all RADIUS
schemes or to view statistics about RADIUS.
display radius statistics
Use the display radius statisticscommand to view the statistics information on RADIUS packets. The
displayed packet information can help you troubleshoot RADIUS faults.
Any view
Any view
display rip
Use the display ripcommand to view the current RIP running state and its configuration information.
56
3Com Router 5000/6000 Family
Command Reference
display rip interface
Use the display rip interfacecommand to display information about the specified RIP interface or all
RIP interface.
Any view
display rip routing
Use the display rip routingcommand to display the RIP routing table, including normal routes and
routes in garbage-collection status.
Any view
Any view
display rip vpn-instance
Use the display rip vpn-instancecommand to view the related configuration of VPN instance of RIP.
display rmon alarm
Use the display rmon alarmcommand to display the alarm table of remote monitoring (RMON) or the
specified alarm entry.
Any view
Any view
display rmon event
Use the display rmon eventcommand to display the event table of RMON or the specified event entry.
display rmon eventlog
Use the display rmon eventlogcommand to display the log table of RMON or the log entry for the
specified event.
Any view
Any view
Any view
display rmon history
Use the display rmon historycommand to display the history control table of RMOM and information
about the latest sampling, such as utilization, number of errors and total number of packets.
display rmon prialarm
Use the display rmon prialarmcommand to display information about the prialarm table of RMON or the
specified prialarm entry.
display rmon statistics
Use the display rmon statisticscommand to display the RMON statistics about the specified or all
interfaces.
Any view
Any view
display route-policy
Use the display route-policycommand to view the configured route-policy
display rsa local-key-pair public
Use the display rsa local-key-pair publiccommand to view the public key of the host key pair and
server key pair on the server. If no key is generated, the system displays: RSA keys not found.
Any view
display rsa peer-public-key
Use the display rsa peer-public-keycommand to view the specified RSA public key. If no public key
specified, all public keys are displayed.
Any view
Any view
display saved-configuration
Use the display saved-configurationcommand to view the configuration file loaded at this startup.
display schedule reboot
Use the display schedule rebootcommand to view settings related to the router’s schedule reboot
terminal service.
Any view
display sftp source-ip
Use the display sftp source-ipcommand to display the source IP address configured for the SFTP
client.
Any view
Any view
display snmp-agent
Use the display snmp-agentcommand to view the engine ID of the local or remote SNMP entity.
3Com Router 5000/6000 Family
Command Reference
57
display snmp-agent community
Use the display snmp-agent communitycommand to view information on the configured communities of
SNMPv1 or SNMPv2.
Any view
display snmp-agent group
Use the display snmp-agent groupcommand to view information about the specified or all user security
model (USM) based groups, including group name, security model, storage type.
Any view
Any view
Any view
Any view
display snmp-agent mib-view
Use the display snmp-agent mib-viewcommand to view the configured MIB views.
display snmp-agent statistics
Use the display snmp-agent statisticscommand to view the state and statistics about SNMP.
display snmp-agent sys-info
Use the display snmp-agent sys-infocommand to view the system information of this SNMP device.
display snmp-agent trap-list
Use the display snmp-agent trap-listcommand to display whether trap sending is enabled on each
module.
Any view
display snmp-agent usm-user
Use the display snmp-agent usm-usercommand to view information about the specified or all SNMP
users.
Any view
Any view
Any view
display sot
Use the display sotcommand to display the current state about SOT connections.
Use the display ssh servercommand to view information on SSH status or sessions.
display ssh server
display ssh server-info
Use the display ssh server-infocommand to view the associations of public key to SSH server
maintained at the client end.
Any view
Any view
display ssh-server source-ip
Use the display ssh-server source-ipcommand to display the source IP address configured for the SSH
server.
display ssh user-information
Use the display ssh user-informationcommand to view information about current SSH users, including
user name, corresponding key name and user authentication mode. If you specify the username
parameter, then only the information about the specified user is displayed.
Any view
Any view
display ssh2 source-ip
Use the display ssh2 source-ipcommand to display the source IP address configured for the SSH client.
display standby flow
Use the display standby flowcommand to view statistics about the traffic on the main interfaces
participating in backup load sharing.
Any view
Any view
display standby state
Use the display standby statecommand to view information about the main and standby interfaces.
display startup
Use the display startupcommand to view the configuration file used at this startup and the one used for
next startup.
User view
58
3Com Router 5000/6000 Family
Command Reference
display status interface
Use the display status interfacecommand to display the state of the specified interface.
Any view
display status interface ima-group
Use the display status interface ima-groupcommand to view detailed information about the specified
IMA group interface.
Any view
display stop-accounting-buffer
Use the display stop-accounting-buffercommand to view information on the stop-accounting requests
buffered in the router.
Any view
Any view
Any view
display tcp statistics
Use the display tcp statisticscommand to view TCP traffic statistic information.
Use the display tcp statuscommand to monitor TCP connection any time.
display tcp status
display tcp status
Use the display tcp statuscommand to view information about the current TCP connections on the
router.
Any view
display telnet-server source-ip
Use the display telnet-server source-ipcommand to display the source IP address configured for the
Telnet server.
Any view
Any view
display tftp-server
Use the display tftp-servercommand to view TFTP server state and attributes setting.
display tftp source-ip
Use the display tftp source-ipcommand to display the source IP address configured for the TFTP
client.
Any view
Any view
display this
Use the display thiscommand to view the current configurations in current view.
display time-range
Use the display time-rangecommand to view the configuration and the status of time range. For the
active time range at present, it displays "active" and for the inactive time range, it displays "inactive".
Any view
Any view
display traffic behavior
Use the display traffic behaviorcommand to display the information of the traffic behavior configured
on the router.
display traffic classifier
Use the display traffic classifiercommand to view the configuration information about class of the
router.
Any view
Any view
display trapbuffer
Use the display trapbuffercommand to view the information entries in the trap buffer.
display udp-helper server
Use the display udp-helper servercommand to display the information about the destination servers
associated with the specified or all Ethernet interfaces.
Any view
Any view
display udp statistics
Use the display udp statisticscommand to view TCP traffic statistic information.
3Com Router 5000/6000 Family
Command Reference
59
display user-interface
Use the display user-interfacecommand to view information about the specified or all user interfaces.
Any view
Any view
Any view
display users
Use the display userscommand to view the login information of the users on each user interface.
Use the display versioncommand to system version information.
display version
display virtual-access
Use the display virtual-accesscommand to view state information about the specified or all virtual
access interfaces.
Any view
Any view
display vlan
Use the display vlancommand to view information on VLANs.
display vlan interface
Use the display vlan interfacecommand to view VLAN configuration information on a certain interface
(only supporting sub-interface).
Any view
Any view
Any view
display vlan max-packet-process
Use the display vlan max-packet-processcommand to view the maximum number of processed packets
configured on a certain VLAN per second.
display vlan statistics vid
Use the display vlan statistics vidcommand to view the packet statistics on a certain VLAN, e.g. the
received packet number and the sent packet number.
display vlan statistics vid
Use the display vlan statistics vidcommand to view the packet statistics on a certain VLAN, e.g. the
received packet number and the sent packet number.
Any view
Any view
Any view
Any view.
display voice aaa-client configuration
Use the display voice aaa-client configurationcommand to view information about voice AAA.
display voice call-history-record
Use the display voice call-history-recordcommand to view the information about call history records.
display voice call-history-record
Use the display voice call-history-recordcommand to view call history.
display voice call-info
Use the display voice call-infocommand to view the call information table, including: channel number
of the call, reference counter of all voice modules, module ID in use, list of the voice entities that can be
selected by the current call, and the voice entity used by the current call.
Any view
Any view
Any view
Any view
display voice default
Use the display voice defaultcommand to view the current default values and the system-fixed default
values for voice and fax.
display voice em call-statistic
Use the display voice em call-statisticcommand to view the call statistics of the digital E&M
subscriber-line.
display voice em ccb
Use the display voice em ccbcommand to view the information of call control block of the E&M
subscriber-line.
60
3Com Router 5000/6000 Family
Command Reference
display voice entity
Use the display voice entitycommand to view the configuration information of voice entities of different
types.
Any view
display voice fax
Use the display voice faxcommand to view the fax statistics in the fax module and the statistics in the
fax transformation module as well.
Any view
Any view
Any view
display voice gateway
Use the display voice gatewaycommand to view the gateway registration state information to GK Server.
Use the display voice ippcommand to view statistics about the IPP module.
display voice ipp
display voice number-substitute
Use the display voice number-substitutecommand to view the configuration information of
number-substitute lists. It can display the information of a certain list and all the lists.
Any view
Any view
display voice r2 call-statistics
Use the display voice r2 call-statisticscommand to view the R2 call statistics.
display voice rcv ccb
Use the display voice rcv ccbcommand to view the information related to the call control block in the
RCV module.
Any view
Any view
Any view
Any view
Any view
display voice rcv statistic
Use the display voice rcv statisticcommand to view the statistics information of calling between the
RCV module and the CC module, VAS module, and so on.
display voice rcv statistic r2
Use the display voice rcv statistic r2command to view the information of call statistics related to the
R2 signaling in the RCV module.
display voice sip call-statistics
Use the display voice sip call-statisticscommand to view all statistic information about the SIP
client.
display voice sip register-state
Use the display voice sip register-statecommand to view the registration state about the SIP user
agents (UAs).
display voice sip register status
Use the display voice sip register statuscommand to display the registration status information of
all subscriber numbers under SIP UAs. The information includes subscriber number (Number), entity
number (Entity), timeout time (Expires) and registration status (Status).
Any view
display voice subscriber-line
Use the display voice subscriber-linecommand to view the configuration information about the type,
status, codec mode, input gain and output attenuation of the subscriber line.
Any view
Any view
Any view
display voice subscriber-line
Use the display voice subscriber-linecommand to view the subscriber line configuration.
display voice vofr call
Use the display voice vofr callcommand to view information of the current call.
display voice vofr statistic
Use the display voice vofr statistic command to view the call statistics between the VoFR module
and VCC, VPP and other modules.
Any view
3Com Router 5000/6000 Family
Command Reference
61
display voice voip data-statistic
Use the display voice voip data-statisticcommand to view statistics information of voice data.
Any view
Any view
display voice vpp
display voice vcc
Use the display voice vppcommand to view all the statistic information in the VPP module.
Use the display voice vcccommand to view the information about the call channel status and call
statistics.
Any view
display voice voip
Use the display voice voip downqueuee1t1vi-bnocommand to display the contents of the down
interrupt queue between the E1/T1 voice card and the router main card.
Use the display voice voip up-queuee1t1vi-nocommand to display the contents of the up interrupt
queue between the E1/T1 voice card and the router main card.
Use the display voice voip phy-statistice1t1vi-bnocommand to display the statistics of the
physical layer.
Any view
Any view
Any view
Any view
display vrrp
Use the display vrrpcommand to view current configuration and state information about VRRP.
display web java-blocking
Use the display web java-blockingcommand to display the information about Java blocking.
display web url-filter host
Use the display web url-filter hostcommand to display information about URL address filtering.
display web url-filter parameter
Use the display web url-filter parametercommand to display the filtering information about SQL
attack.
Any view
Any view
Any view
Any view
Any view
Any view
Any view
Any view
Any view
Any view
display x25 alias-policy
Use the display x25 alias-policycommand to view X.25 alias table.
display x25 cug
Use the display x25 cug command to view the CUG configuration on the router ports.
display x25 hunt-group-info
Use the display x25 hunt-group-infocommand to view the status information of X.25 hunt group.
display x25 map
display x25 map
display x25 pad
Use the display x25 mapcommand to view the X.25 address mapping table.
Use the display x25 mapcommand to display X.25 address map information.
Use the display x25 padcommand to view X.25 PAD connection information.
display x25 switch-table pvc
Use the display x25 switch-table pvccommand to view X.25 switching virtual circuit table.
display x25 switch-table svc
Use the display x25 switch-table svccommand to display the X.25 switching routing table.
display x25 vc
Use the display x25 vccommand to display information about X.25 virtual circuits.
62
3Com Router 5000/6000 Family
Command Reference
display x25 x2t switch-table
Use the display x25 x2t switch-tablecommand to display the dynamic switching routing table and
static routing table.
Any view
Any view
display x25 xot
Use the display x25 xotcommand to view XOT link information.
Use the dl-bitscommand to configure the bit value of all the signals of R2 line signaling.
dl-bits
R2 CAS view
dlsw bridge-set
Use the dlsw bridge-setcommand to configure the bridge group to connect DLSw. Use the undo dlsw
bridge-setcommand to delete the bridge.
System view
System view
dlsw enable
Use the dlsw enablecommand to enable DLSw performance.
dlsw ethernet-backup enable
Use the dlsw ethernet-backup enablecommand to enable DLSw Ethernet redundancy.
Ethernet Interface view
dlsw ethernet-backup map
Use the dlsw ethernet-backup mapcommand to enable the Ethernet switch support feature for DLSw
Ethernet redundancy, that is, to map the MAC address of a remote SNA device to a local virtual MAC
address.
Ethernet Interface view
dlsw ethernet-backup timer
Use the dlsw ethernet-backup timercommand to configure the time for which the master DLSw router
waits before sending a positive or negative response to the slave DLSw router upon receipt of a circuit
establishing request.
Ethernet Interface view
dlsw ethernet-frame-filter
Use the dlsw ethernet-frame-filtercommand to apply an ACL in the transmitting and receiving
directions of DLSW module towards bridge module so that it can transmit and receive only the Ethernet
frames with permitted source MAC addresses.
System view
System view
System view
dlsw filter acl
dlsw local
Use the dlsw filter aclcommand to specify to filter packets from any peer.
Use the dlsw localcommand to create the DLSw local peer.
dlsw max-transmission
Use the dlsw max-transmissioncommand to set the maximum number of the attempts to send an explorer
frame.
System view
System view
System view
dlsw multicast
Use the dlsw multicastcommand to enable the multicast function of DLSw2.0.
dlsw reachable
Use the dlsw reachablecommand to configure locally reachable MAC and SAP addresses.
dlsw reachable-cache
Use the dlsw reachable-cachecommand to add the reachability information of the specified SNA device
to the reachable-cache. You can specify this SNA device by specifying its MAC address and IP address of
the router to which it is connected.
System view
System view
dlsw remote
Use the dlsw remotecommand to create the DLSw remote peer.
3Com Router 5000/6000 Family
Command Reference
63
dlsw remote
Use the dlsw remotecommand to create a remote DLSw peer and specifies its version and filtering rule.
System view
dlsw reverse
Use the dlsw reverse command to convert a MAC address from Ethernet order to token ring order or vice
versa.
System view
System view
System view
dlsw timer
dns domain
dns-list
Use the dlsw timercommand to configure the DLSw timer parameters.
Use the dns domaincommand to configure a DNS domain name.
Use the dns-listcommand to configure DNS server IP addresses in a global DHCP address pool.
DHCP Address Pool view
System view
dns-proxy enable
dns resolve
dns server
domain
Use the dns-proxy enablecommand to enable DNS proxy.
Use the dns resolvecommand to enable DNS resolving.
System view
Use the dns servercommand to configure IP address of a DNS server.
Use the domaincommand to configure an ISP domain or enter the view of an existing ISP domain.
System view
System view
domain-authentication-mode
Use the domain-authentication-modecommand to configure IS-IS route area to authenticate the received
Level-2 routing packets (LSP, CSNP, PSNP), according to the pre-defined mode and password.
IS-IS view
domain-id
Use the domain-id command to specify domain ID for a VPN instance.
OSPF Protocol view
domain-name
Use the domain-namecommand to configure the domain name that a global address pool of the DHCP
server allocates to clients.
DHCP Address Pool view
Voice Number-Substitute view
IKE Peer view
dot-match
Use the dot-matchcommand to configure dot match rules of the number-substitute rules.
Use the dpdcommand to reference a DPD structure.
dpd
dscp media
Use the dscp mediacommand to set the DSCP value in the ToS field in the IP packets that carry the RTP
stream of the voice entity.
Voice Entity view
dsl link-check
Use the dsl link-check enablecommand to enable retraining upon detection of a major fault after the
DSL interface comes up.
ATM (G.SHDSL) Interface view
dtmf
Use the dtmfcommand to configure the way of sending and receiving R2 signaling.
R2 CAS view
dtmf sensitivity-level
Use the dtmf sensitivity-levelcommand to set the detection sensitivity level of DTMF codes.
Voice Subscriber-Line view
64
3Com Router 5000/6000 Family
Command Reference
dtmf threshold
Use the dtmf thresholdcommand to configure the sensitivity of DTMF digit detection.
Use the duplexcommand to set the operating mode of the Ethernet interface.
Use the duplexcommand to configure the duplex mode of the Ethernet port.
Use the dvpn classcommand to create and enter a dvpn-class view.
Voice Subscriber-Line view
Ethernet Interface view
Ethernet Port view
duplex
duplex
dvpn class
System view
dvpn client register-dumb
Use the dvpn client register-dumbcommand to set the time when a client turns to dumb state after it
fails to register with a DVPN server for specified retries.
System view
System view
dvpn client register-interval
Use the dvpn client register-intervalcommand to set the register interval of a client.
dvpn client register-retry
Use the dvpn client register-retry command to set the maximum retries for a client to register with a
DVPN server continuously.
System view
dvpn dvpn-id
Use the dvpn dvpn-idcommand to specify the DVPN domain the tunnel interface belongs to. This
command is valid when the tunnel interface is encapsulated as DVPN.
Tunnel Interface view
dvpn interface-type
Use the dvpn interface-typecommand to specify the type of a tunnel interface. A tunnel interface is of
client type by default.
Tunnel Interface view
System view
dvpn policy
Use the dvpn policycommand to create and enter a DVPN policy view.
dvpn policy
Use the dvpn policycommand to apply a specified DVPN policy to a tunnel interface that is of server type.
Tunnel Interface view
dvpn register-type
Use the dvpn register-typecommand to configure the type of the additional information when a client
registers with a DVPN server.
Tunnel Interface view
dvpn security
Use the dvpn security acl command to configure the ACL used for deciding which data stream needs
IPSec encryption on the tunnel interface.
Tunnel Interface view
Tunnel Interface view
dvpn server
Use the dvpn servercommand to configure the DVPN class to be applied to a tunnel interface.
dvpn server authentication-client method
Use the dvpn server authentication-client methodcommand to specify the default way a DVPN server
authenticates clients.
System view
System view
System view
dvpn server map age-time
Use the dvpn server map age-timecommand to set the map age time of a DVPN server.
dvpn server pre-shared-key
Use the dvpn server pre-shared-keycommand to set a pre-shared key for a DVPN server.
3Com Router 5000/6000 Family
Command Reference
65
dvpn service
Use the dvpn service enablecommand to enable DVPN on a device.
System view
CE3 interface view
CE3 Interface view
CPOS Interface view
CE3 Interface view
CPOS Interface view
CE3 Interface view
CPOS Interface view
CE3 Interface view
CPOS Interface view
CE3 Interface view
CPOS Interface view
CE3 Interface view
CPOS Interface view
SIP Client view
e1 bert
Use the e1 bertcommand to set test error bit for line Bit on CE3 interface.
e1 channel-set
e1 channel-set
e1 set clock
e1 set clock
e1 set frame-format
e1 set frame-format
e1 set loopback
e1 set loopback
e1 shutdown
Use the e1 channel-setcommand to bundle timeslots on an E1 line.
Use the e1 channel-setcommand to bundle multiple timeslots on an E1 channel into one channel set.
Use the e1 set clockcommand to set clocking of an E1 line on the CE3 interface.
Use the e1 set clockcommand to set the clock mode of the E1 channel.
Use the e1 set frame-formatcommand to configure the frame format on an E1 line.
Use the e1 set frame-formatcommand to set the frame format of an E1 channel.
Use the e1 set loopbackcommand to set the loopback mode of the specified E1 line on the E3 interface.
Use the e1 set loopbackcommand to configure the loopback mode of the E1 channel.
Use the e1 shutdowncommand to shut down an E1 line on the CE3 interface.
Use the e1 shutdowncommand to shut down an E1 channel.
e1 shutdown
e1 unframed
Use the e1 unframedcommand to set an E1 line on a CE3 interface to work in unframed mode (E1 mode).
Use the e1 unframed command to set an E1 channel on the CPOS interface to unframed mode or E1 mode.
Use the early-media disablecommand to disable early media negotiation.
Use the ebscommand to set EBS of frame relay virtual circuit.
e1 unframed
early-media disable
ebs
Frame Relay Class view
Voice Subscriber-Line view
R2 CAS view
echo-canceller
effect-time
Use the echo-cancellercommand to configure echo-cancellation parameters.
Use the effect-timecommand to configure the debounce time of line signaling.
eliminate-pulse
Use the eliminate-pulsecommand to eliminate the pulses with a width less than 3.472us, increasing
signal reliability. This is useful when the line is seriously interfered.
Asynchronous Serial Interface view
66
3Com Router 5000/6000 Family
Command Reference
em-phy-parm
em-signal
Use the em-phy-parmcommand to configure a wire scheme for the analog E&M subscriber-line.
Voice Subscriber-Line view
Voice Subscriber-Line view
NetStream Aggregation view
Use the em-signalcommand to configure a voice subscriber-line start mode.
Use the enablecommand to enable current aggregation mode.
enable
enable deactivate
Use the enable deactivatecommand to enable the router to actively deactivate the BSV interface.
BSV Interface view
Interface view
MR view
enable snmp trap undown
Use the enable snmp trap updowncommand to enable the interface to send UPDOWN traps.
encapsulation
Use the encapsulation grecommand to set the MR encapsulation mode to GRE.
Use the encapsulationcommand to specify ATM AAL5 encapsulation type for PVC.
encapsulation
PVC view
encapsulation-mode
Use the encapsulation-modecommand to set the encapsulation mode that the security protocol applies to
IP packets, which can be transport or tunnel.
IPSec Proposal view
System view
encrypt-card backuped
Use the encrypt-card backupedcommand to enable backup function for the encryption card.
encrypt-card fast-switch
Use the encrypt-card fast-switchcommand to enable the fast forwarding function of the encryption card.
System view
encryption-algorithm
Use the encryption-algorithmcommand to specify the encryption algorithm for an IKE proposal.
IKE Proposal view
entity
Use the entitycommand to configure a voice entity and enter its view (at the same time specify the working
mode related to voice).
Voice Dial Program view
error-diffusion restraint config
Use the error-diffusion restraint configcommand to set the three parameters for error diffusion
restraint function.
System view
System view
error-diffusion restraint enable
Use the error-diffusion restraint enablecommand to enable error diffusion restraint.
Use the escape-keycommand to define an escape key or key combination for aborting tasks.
Use the esiscommand to employ ES-IS protocol globally and enter ES-IS view.
Use the esis enablecommand to employ ES-IS protocol on the interface.
escape-key
esis
User Interface view
System view
esis enable
Interface view
esp authentication-algorithm
Use the esp authentication-algorithmcommand to set the authentication algorithm used by ESP.
IPSec Proposal view
3Com Router 5000/6000 Family
Command Reference
67
esp encryption-algorithm
Use the esp encryption-algorithmcommand to set the encryption algorithm adopted by ESP.
IPSec Proposal view
IKE-Peer view
exchange-mode
execute
Use the exchange-modecommand to select an IKE negotiation mode.
Use the executecommand to execute the specified batch file.
System view
exit
Use the exitcommand to terminate the connection to the remote SFTP server and exit to system view as
you would with the byeand quitcommands.
SFTP Client view
expired
Use the expiredcommand to configure a valid period allowed for leasing IP addresses in a global DHCP
address pool.
DHCP Address Pool view
VoIP Voice Entity view
Voice Entity view
fast-connect
fax baudrate
fax ecm
Use the fast-connectcommand to enable fast connect.
Use the fax baudratecommand to configure the highest fax baudrate enabled by the gateway.
Use the fax ecmcommand to configure the forced adoption of ECM mode at the gateway, that is, to make
the facsimiles at both ends support ECM mode.
Voice Entity view
Voice Entity view
Voice Entity view
Voice Entity view
fax level
Use the fax levelcommand to configure the gateway carrier transmitting energy level.
fax local-train threshold
Use the fax local-traincommand to configure the percentage of fax local training threshold value.
fax nsf-on
Use the fax nsf-oncommon to configure the fax faculty transmission mode as Not Standard mode.
fax protocol
Use the fax protocolcommand to configure the protocol for intercommunication with other devices or
enable the fax Passthrough mode, and configure the number of redundant packets sent via the T.38 fax
protocol. The argument standard-t38 indicates the standard T38 negotiation mode specified by H323 or SIP
adopted.
Voice Entity view
Voice Entity view
Voice Entity view
fax support-mode
fax train-mode
fdl
Use the fax support-modecommand to configure the fax interworking mode with other equipments.
Use the fax train-modecommand to configure the training mode used by the gateway.
Use the fdlcommand to set the behavior of the CT1/PRI interface on the FDL in ESF framing.
CT1/PRI Interface view
E1-F Interface view
E1-F Interface view
fe1 clock
Use the fe1 clockcommand to configure clocking on the E1-F interface.
fe1 code
Use the fe1 codecommand to configure the line code format of the E1-F interface.
68
3Com Router 5000/6000 Family
Command Reference
fe1 detect-ais (E1-F interface)
fe1 frame-format
Use the fe1 detect-aiscommand to enable alarm indication signal (AIS) detect on the E1-F interface.
E1-F Interface view
E1-F Interface view
E1-F Interface view
E1-F Interface view
E1-F Interface view
CT3 Interface view
Use the fe1 frame-formatcommand to configure the framing format of the E1-F interface.
fe1 loopback
Use the fe1 loopbackcommand to place the E1-F interface in local or remote loopback.
Use the fe1 timeslot-listcommand to bundle timeslots on the E1-F interface.
fe1 timeslot-list
fe1 unframed
Use the fe1 unframedcommand to configure an E1-F interface to work in unframed mode.
Use the feaccommand to enable FEAC channel signal detection and sending on the CT3 interface.
Use the fifo queue-lengthcommand to set the FIFO queue length of frame relay virtual circuit.
feac (CT3 Interface)
fifo queue-length
file prompt
Frame Relay Class view
Use the file promptcommand to enable or disable the router to warn when an operation may result in
data loss or corruption.
System view
filename
Use the filenamecommand to configure the name of the file to be gotten from or put onto an FTP server.
HWPing Test Group view
filter-policy
Use the filter-policy exportcommand to configure the filtering conditions of the routing information
advertised by a certain type of routing protocols.
Routing Protocol view
filter-policy export
Use the filter-policy export command to filter the advertised routes and only the routes passing the
filter can be advertised by BGP.
BGP Unicast view
BGP Multicast view
VPNv4 view
VPN Instance view
filter-policy export
filter-policy export
Use the filter-policy exportcommand to configure IS-IS to filter all redistributed routes or routes
redistributed from a specified routing protocol.
IS-IS view
Use the filter-policy exportcommand to configure OSPF to filter the LSAs of redistributed routes for
advertisement.
OSPF view
RIP view
filter-policy export
Use the filter-policy exportcommand to configure to filter the advertised routing information by RIP.
filter-policy gateway
Use the filter-policy gateway import command to filter the routing information advertised by a
specified router.
Use the filter-policy import command to configure the condition for filtering the routing information.
Routing Protocol view
3Com Router 5000/6000 Family
Command Reference
69
filter-policy import
Use the filter-policy gateway importcommand to filter the learned routing information advertised by
the specified address.
Use the filter-policy import command to filter the received global routing information.
BGP Unicast view
BGP Multicast view
VPNv4 view
VPN Instance view
filter-policy import
filter-policy import
Use the filter-policy importcommand to configure to filter the routes received by IS-IS.
IS-IS view
Use the filter-policy importcommand to configure the OSPF rules of filtering the routing information
received.
Use the filter-policy importcommand to filter the routes calculated by OSPF. Only the filtered routes
can be added to the routing table. The filtering can be performed according to the next hop and destination
of the route.
OSPF view
filter-policy import
Use the filter-policy gatewaycommand to configure to filter the received routing information distributed
from the specified address.
Use the filter-policy importcommand to configure the filtering to the received global routing
information.
RIP view
final-callednum
Use the final-callednumcommand to enable or disable the terminate signal to be sent to the terminating
point after the called number is sent.
R2 CAS view
Interface view
firewall aspf
Use the firewall aspfcommand to apply ASPF policy in specified direction to an interface.
firewall default
Use the firewall defaultcommand to configure the default filtering rule of the firewall, whether to be
“permit” or “deny”.
System view
System view
Interface view
System view
firewall enable
Use the firewall enablecommand to enable the firewall.
firewall ethernet-frame-filter
Use the firewall ethernet-frame-filtercommand to apply a MAC-based ACL on the interface.
firewall fragments-inspect
Use the firewall fragments-inspectcommand to enable fragment inspection switch.
firewall fragments-inspect {high | low}
Use the firewall fragments-inspect { high | low }command to configure the high and low thresholds
of records for fragment inspection.
System view
Interface view
firewall packet-filter
Use the firewall packet-filtercommand to apply the access control list to the corresponding interface.
first-rule
Use the first-rulecommand to configure the number-substitute rule that is first used in the current
number-substitute list.
Voice Number-Substitute view
fixdisk
Use the fixdiskcommand to restore the space of a storage device when it becomes unavailable because
of some abnormal operation.
User view
70
3Com Router 5000/6000 Family
Command Reference
flag
Use the flagcommand to set the overhead byte of SONET/SDH frames.
Use the flagcommand to set the SDH overhead byte.
CPOS Interface view
POS Interface view
flag
flow control
Use the flow-controlcommand to enable flow control on the Ethernet interface, which is useful only when
the peer end also supports flow control.
Ethernet Interface view
flow-control
Use the flow-controlcommand to enable flow control on the Ethernet port to avoid packet drop when
congestion occurs.
Ethernet Port view
User Interface view
System view
flow-control
Use the flow-controlcommand to configure flow control mode.
flow interval
flow-interval
flow-interval qos
Use the flow-intervalcommand to configure traffic statistic interval.
Use the flow-intervalcommand to configure the interval for measuring the average rate of the interfaces.
System view
Use the flow-interval qoscommand to configure QoS policy traffic statistical interval and QoS policy rate
updating interval.
System view
GE Interface view
R2 CAS view
force-link
force-metering
format
Use the force-linkcommand to enable the GE interface to work in force mode.
Use the force-meteringcommand to enable or disable the metering signal of R2 signaling.
Use the formatcommand to format a storage device.
User view
fqdn
Use the fqdncommand to specify the FQDN of an entity.
PKI Entity view
fr bump
Use the fr bumpcommand to configure the standby PVC that will take over when a specified PVC goes
down.
FR Pvc-Group view
fr-class
Use the fr-classcommand to associate a frame relay class with the current frame relay virtual circuit or
frame relay interface.
Frame Relay DLCI view
fr class
Use the fr classcommand to create a frame relay class and enter frame relay class view.
Use the fr compression frf9command to enable the FRF9 compression function.
Use the fr compression iphccommand to enable the IP header compression.
System view
fr compression frf9
fr compression iphc
Frame Relay Interface view
Frame Relay Interface view
3Com Router 5000/6000 Family
Command Reference
71
fr congestion-threshold
Use the fr congestion-thresholdcommand to enable congestion management function of a frame relay
interface.
Frame Relay Interface view
MFR Interface view
fr de del
Use the fr de delcommand to apply a DE rule list to the specified frame relay virtual circuit.
Frame Relay Interface (or Subinterface) view
MFR Interface view
fr del inbound-interface
Use the fr del inbound-interfacecommand to configure an interface-based DE rule list. For the packet
received from the specified interface, if it is forwarded from the router as a frame relay packet, its DE flag
bit is set to 1 before being forwarded.
System view
System view
fr del protocol ip
Use the fr del protocol ipcommand to configure an IP-based DE rule list. The DE flag bit of the frame
relay packet encapsulated with an IP packet matching the specified rule will be flagged as 1.
fr dlci
Use the fr dlcicommand to configure the virtual circuit for Frame Relay interface.
Interface view
PVC Group view
fr dlci-switch
Use the fr dlci-switchcommand to configure a static route for frame relay PVC switching.
Frame Relay Interface view
MFR Interface view
fr inarp
Use the fr inarpcommand to enable the inverse address resolution of Frame Relay.
Use the fr interface-typecommand to set the Frame Relay interface type.
Interface view
Interface view
fr interface-type
fr ip-dscp
Use the fr ip-dscpcommand to configure the PVC to carry packets of the specified priority levels when
the DSCP identifier in the IP packet is used to identify the priority levels of packets.
FR Pvc-Group view
FR Pvc-Group view
fr ip-precedence
Use the fr ip-precedencecommand to configure the PVC to carry packets of the specified priority levels
when the Precedence identifier in the IP packet is used to identify the priority levels of packets.
fr iphc
Use the fr iphccommand to enable IP header compression function, including RTP/TCP header
compression.
Frame Relay Interface view
MFR Interface view
fr lmi n391dte
fr lmi n392dce
fr lmi n392dte
fr lmi n393dce
fr lmi n393dte
Use the fr lmi n391dtecommand to configure N391 parameter at the DTE side.
Use the fr lmi n392dcecommand to set N392 parameter at the DCE side.
Use the fr lmi n392dtecommand to set N392 parameter at the DTE side.
Use the fr lmi n393dcecommand to set the N393 parameter at the DCE side.
Interface view
Interface view
Interface view
Interface view
Interface view
Use the fr lmi n393dtecommand to set N393 parameter at the DTE side.
72
3Com Router 5000/6000 Family
Command Reference
fr lmi t392dce
fr lmi type
fr map bridge
fr map clns
fr map ip
Use the fr lmi t392dcecommand to set T392 parameter at the DCE side.
Use the fr lmi typecommand to configure the Frame Relay LMI protocol type.
Use the fr map bridgecommand to add a bridge-set to frame relay map entry.
Use the fr map clns command to add an FR mapping for OSI packets.
Use the fr map ipcommand to add an IP address map entry for FR.
Use the fr map ipxcommand to add an IPX address map entry.
Interface view
Interface view
Interface view
Interface view
Interface view
Interface view
fr map ipx
fr map ppp interface virtual-template
Use the fr map ppp interface virtual-templatecommand to map the FR DLCI (corresponds to an FR
PVC) to a PPP link, so the PPPoFR link is established, and thus PPP packets can be sent/received on FR
PVC.
Interface view
fr match
Use the fr matchcommand to configure a PVC group to differentiate traffic by the Precedence or DSCP
identifier in the TOS field of the IP header.
FR Pvc-Group view
fr mpls-exp
Use the fr mpls-expcommand to configure the PVC to carry packets of the specified priority levels when
the EXP identifier in the MPLS packet is used to identify the priority levels of packets.
FR Pvc-Group view
Interface view
fr pvc-group
fr pvc-pq
Use the fr pvc-groupcommand to create a PVC group.
Use the fr pvc-pqcommand to set the queue type of a frame relay interface as PVC PQ (PVC Priority
Queuing) and set queue length, i.e. the maximum number of packets that can be held by a queue, for each
queue.
Frame Relay Interface view
MFR Interface view
fr pvc-protect
fr switch
Use the fr pvc-protectcommand to configure the protection mode for a PVC in a PVC group.
FR Pvc-Group view
Use the fr switchcommand to create a PVC used for frame relay switching and enter frame relay
switching view.
System view
System view
fr switching
Use the fr switchingcommand to enable frame relay PVC switching.
Use the fr traffic-policingcommand to enable FRTP function.
fr traffic-policing
Frame Relay Interface view
MFR Interface view
fr traffic-shaping
Use the fr traffic-shapingcommand to enable FRTS function.
Frame Relay Interface view
MFR Interface view
3Com Router 5000/6000 Family
Command Reference
73
fragment
Use the fragmentcommand to enable the FRF.12-compliant fragmentation function on frame relay virtual
circuit.
Frame Relay Class view
frame-format
frame-format
frame-format
frame-format
frame-format
Use the frame-formatcommand to set the frame format of ATM OC-3c/STM-1 interface.
Use the frame-formatcommand to configure the ATM over E1/T1 framing format.
Use the frame-formatcommand to configure frame format of ATM E3/T3 interface.
Use the frame-formatcommand to set the frame type of the CPOS interface.
Use the frame-formatcommand to set the frame format of the POS interface.
ATM Interface view
ATM E1/T1 Interface view
ATM E3/T3 Interface view
CPOS Interface view
POS Interface view
frame-format (CE1/PRI Interface)
Use the frame-formatcommand to set the frame format on the CE1 interface.
CE1/PRI Interface view
CT1/PRI Interface view
CT3 Interface view
frame-format (CT1/PRI Interface)
Use the frame-formatcommand to set the frame format on the CT1/PRI interface.
frame-format (CT3 Interface)
Use the frame-formatcommand to configure the frame format used by the CT3 interface.
frame-length
Use the frame-lengthcommand to configure the number of ATM cells in an IMA frame.
IMA Group Interface view
Synchronous Serial Interface view
framefill none
Use the framefill nonecommand to disable a serial interface to send interframe filling tags.
Asynchronous Serial Interface view
AUX Interface view
AM Interface view
free unused porttag
free user-interface
Use the free unused porttagcommand to release the port tag resources used by removed interfaces for
creating new interfaces.
System view
Use the free user-interface numbercommand to disconnect the user corresponding to the user
interface specified by its absolute index.
User view
frequency
Use the frequencycommand to configure an automatic test interval.
HWPing Test Group view
ft1 alarm-threshold
Use the alarm-thresholdcommand to configure the alarm thresholds on the T1-F interface as needed.
T1-F Interface view
T1-F Interface view
T1-F Interface view
ft1 bert (T1-F Interface)
Use the ft1 bertcommand to start a BERT test on the T1-F interface.
ft1 cable
Use the ft1 cablecommand to configure attenuation or transmission segment matching the T1-F interface.
74
3Com Router 5000/6000 Family
Command Reference
ft1 clock
Use the ft1 clockcommand to configure clocking on the T1-F interface.
Use the ft1 codecommand to configure line code format for a T1-F interface.
T1-F Interface view
T1-F Interface view
ft1 code
ft1 data-coding
Use the ft1 data-coding normalcommand to disable user data inversion on the T1-F interface.
Use the ft1 data-coding invertedcommand to enable user data inversion on the CT1/PRI interface.
T1-F Interface view
T1-F Interface view
T1-F Interface view
T1-F Interface view
T1-F Interface view
ft1 fdl
Use the ft1 fdlcommand to set the behavior of the T1-F interface on the FDL in ESF framing.
Use the ft1 loopbackcommand to place the T1-F interface in local or remote loopback.
Use the sendloopcodecommand to send remote loopback control code.
ft1 loopback
ft1 sendloopcode
ft1 timeslot-list
ft3 (CT3 Interface)
Use the ft1 timeslot-listcommand to bundle timeslots on the T1-F interface.
Use the ft3command to configure the CT3 interface to operate in FT3 mode and to set the DSU mode and
subrate for FT3.
CT3 Interface view
User view
ftp
Use the ftpcommand to set up control connection to the remote FTP server and enter FTP client view.
ftphost source-interface
Use the ftphostsource-interfacecommand to specify the source interface that the FTP client uses
when accessing the specified FTP server. This interface must be an exiting local interface.
User view
User view
ftphost source-ip
Use the ftphost source-ipcommand to specify the source IP address that the FTP client uses when
accessing the specified FTP server.
ftp-operation
Use the ftp-operationcommand to configure the FTP operation done by the system.
HWPing Test Group view
System view
ftp server enable
Use the ftp server enablecommand to enable the FTP server to allow login of FTP users.
ftp-server source-interface
Use the ftp-server source-interfacecommand to specify a source interface, which must be an existing
local interface, for the FTP server.
System view
System view
System view
System view
ftp-server source-ip
ftp source-interface
ftp source-ip
Use the ftp-server source-ipcommand to specify a source IP address for the packets sent by the FTP
server. This IP address must be a local IP address.
Use the ftp source-interfacecommand to specify a source interface, which must be an existing local
interface, for the FTP client.
Use the ftp source-ipcommand to specify a source IP address for the packets sent by the FTP client.
This IP address must be a local IP address.
3Com Router 5000/6000 Family
Command Reference
75
ftp timeout
Use the ftp timeoutcommand to set the idle-timeout timer.
System view
System view
ftp update
Use the ftp updatecommand to set the file update mode that the FTP server uses while receiving data.
fxo-monitoring
Use the fxo-monitoring enable command to enable the on line monitoring function on all FXO interfaces of
the device.
Voice view
gateway-list
Use the gateway-listcommand to configure IP addresses of the egress GW routers used by DHCP
clients.
DHCP Address Pool view
get
Use the getcommand to FTP a file from a remote server and save it.
Use the getcommand to download and save a file from a remote server.
FTP Client view
get
SFTP Client view
gk-2nd-id
Use the gk-2nd-idcommand to configure the name and IP address of the backup GK Server corresponding
to the gateway.
Use the gk-2nd-id command to configure the IP address, name and port of the backup GK Server.
Use the gk-clientcommand to enter Voice GK client view, and configure the GK parameters for voice.
Use the gk-idcommand to configure the GK Server name and IP address corresponding to the gateway.
Voice GK Client view
Voice view
gk-client
gk-id
Use the command gk-id to configure such information as the IP address, name, and port of GK Server to
facilitate the research for the right GK Server equipment by the GK Client according to this information, so
as to implement the register task of gateway in the GK Server.
Voice GK Client view
gk-security call
Use the gk-security call enablecommand to enable security calls on the GK Client (router).
Voice GK Client view
gk-security register-pwd
Use the gk security register-pwdcommand to set the GK register password.
Use the gk-security register-pwd command to remove the GK register password.
Voice GK Client view
System view
gratuitous-arp-learning enable
Use the gratuitous-arp-learning enablecommand to enable the address learning function of gratuitous
ARP.
gratuitous-arp-sending enable
Use the gratuitous-arp-sending enablecommand to configure the system to return ARP responses
when receiving gratuitous ARP packets from other network segments. The system, however, does not learn
the received ARP entries.
System view
Tunnel Interface view
Tunnel Interface view
gre checksum
Use the gre checksumcommand to configure the two ends of a tunnel to perform end-to-end check,
verifying the correctness of packets and discard those that do not pass the verification.
gre key
Use the gre keycommand to set identification keyword of the tunnel interface, and by this feeble security
mechanism avoid incorrectly identifying or receiving packets from undesired places.
76
3Com Router 5000/6000 Family
Command Reference
group
Use the groupcommand to create a peer group.
BGP view
group-b
Use the group-bcommand to enable or disable Group-B stage signal to complete register exchange.
Use the gtscommand to configure traffic shaping for a behavior.
R2 CAS view
gts
Traffic Behavior view
gw-access-number
Use the gw-access-numbercommand to configure the access service number or enter the view of the
access service number.
Voice Dial Program view
Voice GK Client view
gw-address
gw-id
Use the gw-addresscommand to configure the source IP address used by the voice gateway.
Use the gw-idcommand to configure the gateway alias.
Use the command gw-idto configure the gateway alias, which is used for the gateway to register and
identify the voice gateway. Each gateway has only one alias, and the new alias will cover the old one.
Voice GK Client view
System view
header
help
Use the headercommand to create a banner.
Use the helpcommand to get the help information for the specified or all SFTP client commands.
SFTP Client view
User Interface view
history-command max-size
Use the history-command max-sizecommand to set the size of history command buffer.
history keep-time
history-record
Use the history keep-timecommand to configure the retaining time of the history record for a test group.
HWPing Test Group view
HWPing Test Group view
Use the history-record enablecommand to enable history record.
history-records
home-agent ip-address
hookoff-time
Use the history-recordscommand to configure the number of test results that the system can retain.
HWPing Test Group view
Use the home-agent ip-addresscommand to configure the HA address of the MR.
MR view
Use the hookoff-timecommand to configure the hangup timer. When this timer times out, the interface
hangs up.
FXO Voice Subscriber-Line view
host-route
hotkey
Use the host-routecommand to control the RIP to accept the host route.
Use the hotkeycommand to assign a hot key to a command line.
Use the http-operationcommand to configure an HTTP operation type.
RIP view
System view
http-operation
HWPing Test Group view
3Com Router 5000/6000 Family
Command Reference
77
hwatacacs change-password self
Use the hwtacacs change-password selfcommand to enable the TACACS online user to change the
password.
User view
hwatacacs nas-ip
hwatacacs scheme
Use the hwtacacs nas-ipcommand to specify the source address of the hwtacacs packet sent from NAS.
System view
Use the hwtacacs schemecommand to enter TACACS+ Server view. If the specified TACACS+ server
scheme does not exist, you can create a new TACACS+ scheme.
System view
System view
System view
System view
System view
System view
System view
System view
IKE-Peer view
hwping
Use the hwpingcommand to create an HWPing test group.
hwping-agent enable
Use the hwping-agent enablecommand to enable the HWPing client function.
hwping-agent max-requests
Use the hwping-agent max-requestscommand to set the allowed maximum number of concurrent tests.
hwping-server enable
Use the hwping-server enablecommand to enable HWPing Server.
hwping-server tcpconnect
Use the hwping-server tcpconnectcommand to create a TCP listening service.
hwping-server udpecho
icmp redirect send
id-type
Use the hwping-server udpechocommand to create a UDP listening service.
Use the icmp redirect sendcommand to enable the sending of ICMP Redirect messages.
Use the id-typecommand to select the type of ID used in IKE negotiation.
idle-mark
Use the idle-markcommand to set the line idle-mark of the synchronous serial interface to “FF”.
Synchronous Serial Interface view
idle-timeout
Use the idle-timeoutcommand to set the idle-timeout timer. When it expires, the user connection is
disconnected.
User Interface view
idlecode (CE1/PRI Interface)
Use the idlecodecommand to set the line idle code on the CE1/PRI interface. Two types of line idle code
are available: 0x7e and 0xff.
CE1/PRI Interface view
idlecode (CT1/PRI Interface)
Use the idlecodecommand to set the line idle code on the CT1/PRI interface. Two types of line idle code
are available: 0x7e and 0xff.
CT1/PRI Interface view
if-match
Use the if-matchcommand to define the match rule of a class.
Use the if-match aclcommand to define ACL match rule.
Class view
Class view
if-match acl
if-match acl
Use the if-match aclcommand to set conditions that multicast packets should meet in each policy node.
Route-Policy view
78
3Com Router 5000/6000 Family
Command Reference
if-match acl
Use the if-match aclcommand to set the match condition for IP address.
Route-Policy view
if-match acl
Use the if-match aclcommand to configure the IP address range to match the route-policy.
Use the if-match anycommand to define the rule matching all packets.
Use the if-match as-pathcommand to filter BGP routing information.
Routing Policy view
Class view
if-match any
if-match as-path
if-match atmclp
Routing Policy view
Use the if-match atmclpcommand to create a cell loss priority (CLP) bit match rule defining that ATM cells
with CLP bit set to 1 are matched.
Use the if-match not atmclpcommand to create a CLP bit match rule defining that ATM cells with CLP
bit set to 0 are matched.
Class view
Class view
if-match classifier
if-match community
Use the if-match classifiercommand to define class-map match rule.
Use the if-match communitycommand to configure the community list number to be matched in
route-policy.
Routing Policy view
Routing Policy view
if-match cost
Use the if-match costcommand to configure one of the matching rules of route-policy to match the cost
of the routing information.
if-match {destination-mac | source-mac}
Use the if-match{ destination-mac | source-mac } command to define match rule of destination or source
MAC address.
Class view
Class view
if-match dot1p-cos
if-match dscp
Use the if-match dot1p-coscommand to define a COS field match rule for VLAN packets.
Use the if-match dscpcommand to define an IP DSCP match rule.
Use the if-match fr-decommand to define an FR DE matching rule.
Class view
if-match fr-de
Class view
if-match inbound-interface
Use the if-match inbound-interfacecommand to define ingress interface match rule of a class.
Class view
if-match interface
Use the if-match interfacecommand to match the route whose next hop is designated interface.
Routing Policy view
if-match ip next-hop
Use the if-match ip next-hopcommand to configure one of the match rules of route-policy on the next
hop address of the routing information.
Routing Policy view
Class view
if-match ip-precedence
Use the if-match ip-precedencecommand to define IP precedence match rule.
if-match ip-prefix
Use the if-match ip-prefixcommand to configure one of the match rules of route-policy on the IP
address range of the routing information.
Routing Policy view
3Com Router 5000/6000 Family
Command Reference
79
if-match mpls-exp
Use the if-match mpls-expcommand to configure the matching rule for EXP domain of MPLS.
Class view
if-match mpls-label
Use the if-match mpls-label command to configure to match public network routes with MPLS labels
only.
Route-Policy view
if-match outbound-interface
Use the if-match outbound-subinterfacecommand to define an outbound subinterface matching rule for
the class.
Class view
Route-Policy view
Class view
if-match packet length
Use the if-match packet-lengthcommand to set length match conditions of IP packets.
Use the if-match protocolcommand to define protocol matching rules.
Use the if-match protocol rtpcommand to configure RTP matching rules.
Use the if-match rtpcommand to define port match rule of RTP.
if-match protocol
if-match protocol rtp
if-match rtp
Class view
Class view
if-match tag
Use the if-match tagcommand to match the tag field of OSPF route information.
Use the igmp enablecommand to enable IGMP on an interface.
Routing Policy view
Interface view
igmp enable
igmp group-limit
Use the igmp group-limit command to limit the number of IGMP groups joined on the interface. If the
number exceeds the limit, the router will not process the joined IGMP packet any more.
Interface view
igmp group-policy
igmp host-join
Use the igmp group-policycommand to set the filter of multicast groups on an interface to control the
accessing to the IP multicast groups.
Interface view
Interface view
Use the igmp host-joincommand to enable an interface of a router to join a multicast group.
igmp lastmember-queryinterval
Use the igmp lastmember-queryinterval command to set the interval at which IGMP querier sends the
IGMP specified group query packet when it receives IGMP Leave packet from the host.
Interface view
Interface view
Interface view
Interface view
igmp max-response-time
Use the igmp max-response-timecommand to configure the maximum response time contained in the
IGMP query packet.
igmp proxy
Use the igmp proxycommand to specify an interface of a leaf network router as the IGMP proxy of another
interface.
igmp robust-count
Use the igmp robust-countcommand to set the times IGMP querier sends the IGMP specified group query
packet when it receives IGMP Leave packet from the host.
80
3Com Router 5000/6000 Family
Command Reference
igmp timer other-querier-present
Use the igmp timer other-querier-presentcommand to configure the overtime value of presence of
IGMP querier.
Interface view
igmp timer query
Use the igmp timer query command to configure the interval at which a router interface sends IGMP query
messages.
Interface view
Interface view
igmp version
Use the igmp versioncommand to specify the version of IGMP that a router uses.
ignore-lsp-checksum-error
Use the ignore-lsp-checksum-error command to configure the IS-IS to ignore the checksum error of
LSP.
IS-IS view
System view
System view
ike dpd
Use the ike dpdcommand to create a DPD structure and enter its view.
Use the ike local-namecommand to set the name of the local GW.
ike local-name
ike next-payload check disabled
Use the ike next-payload check disabledcommand to disable the router to check the next-payload field
in the last payload of the IKE negotiation packet during IPSec negotiation for compatibility with other
vendors.
System view
ike peer (IPSec Policy view or IPSec Policy Template view)
Use the ike peercommand to quote an IKE peer in an IPSec policy or IPSec policy template.
IPSec Policy view
IPSec Policy Template view
ike peer (System view)
Use the ike peercommand to configure an IKE peer and access IKE-peer view.
System view
System view
ike proposal
Use the ike proposalcommand to define an IKE proposal.
ike sa keepalive-timer interval
Use the ike sa keepalive-timer interval command to configure the interval for sending Keepalive
packet to the remote end through ISAKMP SA.
System view
System view
System view
ike sa keepalive-timer timeout
Use the ike sa keepalive-timer timeoutcommand to configure a timeout for ISAKMP SA to wait for the
Keepalive packet.
ike sa nat-keepalive-timer interval
Use the ike sa nat-keepalive-timer intervalcommand to configure the NAT keepalive interval for IKE
peers.
ima-clock
Use the ima-clockcommand to configure the clock mode of the IMA group.
IMA Group Interface view
ima ima-group
Use the ima ima-groupcommand to add the ATM E1/T1 interface to the specified IMA group. If the
specified IMA group does not exist, it is created first.
ATM E1/T1 Interface view
ima-test
Use the ima-testcommand to set a test pattern for testing the connectivity of the specified link to the rest
of the IMA group.
IMA Group Interface view
3Com Router 5000/6000 Family
Command Reference
81
impedance
Use the impedancecommand to configure the current electric impedance on a voice subscriber-line.
FXO Voice Subscriber-Line view
import-route
Use the import-routecommand to redistribute routes from other protocols.
BGP view
import-route
import-route
import-route
import-route
import-route isis
Use the import-routecommand to import routing information from other protocols to BGP.
IPv4 Multicast Subaddress Family view
Use the import-routecommand to configure IS-IS to filter the redistributed routes.
IS-IS view
Use the import-routecommand to redistribute the information of another routing protocol.
Use the import-routecommand to redistribute the routes of other protocols into RIP.
OSPF view
RIP view
Use the import-route isis level-2 into level-1command to enable routing information in a Level-2
area to be redistributed to a Level-1 area.
IS-IS view
import-route ospf
import-source
Use the import-route ospfcommand to enable to import OSPF route.
BGP Unicast/Multicast view
MBGP VPN-Instance Address Family view
Use the import-sourcecommand to configure which (S, G) entries in the domain need to be advertised
when a MSDP originates an SA message.
MSDP view
System view
info-center channel
Use the info-center channelcommand to assign a name to the information channel specified by
channel-number.
info-center console channel
Use the info-center console channel command to have the info-center output information to the console
over the specified channel.
System view
System view
info-center enable
Use the info-center enablecommand to enable the info-center.
info-center logbuffer
Use the info-center logbuffercommand to enable the log buffer and specify the channel for system
information output as well as the size of the log buffer.
System view
info-center logfile
info-center loghost
Use the info-center logfile channelcommand to have the info-center output system information to the
log file.
System view
System view
Use the info-center loghostcommand to have the info-center output information to the log host.
info-center loghost source
Use the info-center loghost sourcecommand to specify the source address in the packets destined to
the log host.
System view
82
3Com Router 5000/6000 Family
Command Reference
info-center monitor channel
Use the info-center monitor channel command to have the info-center output information over the
specified channel to the user terminal.
System view
System view
System view
System view
info-center snmp channel
Use the info-center snmp channelcommand to set the information channel for SNMP.
Use the info-center sourcecommand to add records to an information channel.
info-center source
info-center synchronous
Use the info-center synchronouscommand to enable synchronous terminal output.
info-center timestamp
Use the info-center timestampcommand to set a time stamp format for the system information output to
the information channels except for the log host.
System view
System view
info-center timestamp loghost
Use the info-center timestamp loghostcommand to set a time stamp format for the system information
output to the log host.
info-center trapbuffer
Use the info-center trapbuffercommand to enable the trap buffer, set its size and the channel that
outputs information to it.
System view
System view
interface
interface
Use the interfacecommand to create a P2MP or P2P subinterface.
Use the interfacecommand to enter the specified interface view or create a logical interface or
subinterface.
System view
System view
System view
interface
Use the interfacecommand to enter Ethernet port view.
interface atm
Use the interface atmcommand to enter the view of the specified ATM E1/T1 interface.
interface bridge-template
Use the interface bridge-templatecommand to create a bridge template interface, connecting the
specified bridge set to the routing network.
System view
interface dialer
Use the interface dialercommand to create a dialer circular group for the Circular DCC, or configure a
dialer interface for the Resource-Shared DCC.
System view
System view
System view
System view
System view
interface encrypt
interface ethernet
interface ima
Use the interface encryptcommand to enter encryption card interface view.
Use the interface ethernetcommand to create an Ethernet subinterface.
Use the interface imacommand to enter the specified IMA group interface view.
interface logic-channel
Use the interface logic-channelcommand to create a logical channel interface.
3Com Router 5000/6000 Family
Command Reference
83
interface loopback
Use the interface loopbackcommand to create a loopback interface or its view.
System view
interface mfr
Use the interface mfrcommand to create a multilink frame relay bundle interface or sub-interface and
enter the corresponding interface view.
System view
System view
System view
interface mp-group
interface null
Use the interface mp-groupwcommand to create an MP-group interface.
Use the interface nullcommand to enter null interface view.
interface serial [ p2p | p2mp ]
Use the interface serial[ p2p | p2mp ]command to configure type of the specified FR subinterface
and enter frame relay subinterface view.
System view
System view
System view
interface tunnel
Use the interface tunnelcommand to create a tunnel interface and enter the view of this tunnel interface.
interface virtual-ethernet
Use the interface virtual-ethernetcommand to create a virtual Ethernet interface.
interface virtual-template
Use the interface virtual-templatecommand to create a virtual template or enter the existing virtual
template view.
System view
interval-time
Use the interval-timecommand to configure the interval for triggering DPD query.
DPD Structure view
invert receive-clock
Use the invert receive-clockcommand to invert the receive-clock signal on the DTE-side synchronous
serial interface.
Serial Interface View
invert transmit-clock
Use the invert transmit-clockcommand to enable the inverting of the transmit-clock signal of the
synchronous serial interface at the DTE side.
Serial Interface view
PKI Entity view
HA-MR view
ip
Use the ipcommand to specify the IP address of an entity.
ip address
ip address
ip address
Use the ip addresscommand to configure the home address of an MR.
Use the ip addresscommand to set an IP address for an interface.
Use the ip addresscommand to configure the home address of an MR.
Interface view
MR view
ip address bootp-alloc
Use the ip address bootp-alloccommand to configure the Ethernet interface to obtain IP address using
BOOTP.
Ethernet Interface view
ip address dhcp-alloc
Use the ip address dhcp-alloccommand to enable DHCP client on the Ethernet or WAN interface for
obtaining local IP address.
Interface view (Ethernet Interface or Subinterface)
Synchronous/Asynchronous Serial Interface (encapsulated with PPP, HDLC, or frame relay, E1 interface)
84
3Com Router 5000/6000 Family
Command Reference
ip address ppp-negotiate
Use the ip address ppp-negotiatecommand to allow IP address be assigned through negotiation at the
interface.
Interface view
ip address unnumbered
Use the ip address unnumberedcommand to enable an interface to borrow the IP address of another
interface.
Interface view
System view
ip as-path-acl
Use the ip as-path-aclcommand to configure an AS path regular expression.
ip binding vpn-instance
ip community-list
Use the ip binding vpn-instance command to bind an interface or subinterface to a vpn-instance.
Interface (or Subinterface) view
Use the ip community-listcommand to configure a BGP community list.
System view
ip count enable
Use the ip count enablecommand to enable IP accounting.
System view
ip count exterior threshold
Use the ip count exterior-thresholdcommand to configure maximum number of entries in the exterior
hash table, with each entry for an IP packet that does not match any IP accounting rule.
System view
Interface view
Interface view
System view
ip count firewall denied
Use the ip count firewall-deniedcommand to configure the IP Accounting to count the IP packets
denied by the firewall on the current interface.
ip count inbound packets
Use the ip count inbound-packetscommand to configure the IP Accounting to count inbound IP packets
on the current interface.
ip count interior threshold
Use the ip count interior-thresholdcommand to configure maximum number of entries in the interior
hash table, with each entry for an IP packet matching the IP accounting rule.
ip count outbound-packets
Use the ip count outbound-packetscommand to configure the IP Accounting to count outbound IP
packets on the current interface.
Interface view
System view
System view
System view
ip count rule
ip count timeout
ip df-check enable
ip-dscp
Use the ip count rulecommand to configure IP accounting rules.
Use the ip count timeoutcommand to configure the aging time of IP accounting entries.
Use the ip df-check enablecommand to enable don’t fragment bit (DF-bit) check for IP packets.
Use the ip-dscpcommand to configure the PVC to carry packets of the specified priority levels when the
DSCP identifier in the IP packet is used to identify the priority levels of packets.
ATM Pvc-Group view
3Com Router 5000/6000 Family
Command Reference
85
ip fast-forwarding
Use the ip fast-forwardingcommand to enable unicast fast packet forwarding on both inbound and
outbound interfaces.
Use the ip fast-forwardinginbound command to enable unicast fast packet forwarding on the inbound
interface.
Use the ip fast-forwardingoutbound command to enable unicast fast packet forwarding on the outbound
interface.
Interface view
Interface view
System view
System view
System view
Interface view
ip forward-broadcast
Use the ip forward-broadcastcommand to enable the current interface to forward broadcasts.
Use the ip hostcommand to configure the IP address corresponding to a host name.
Use the ip ip-prefixcommand to configure an address prefix list or one of its items.
ip host
ip ip-prefix
ip local policy route-policy
Use the ip local policy route-policycommand to enable local policy routing.
ip multicast-fast-forwarding
Use the ip multicast-fast-forwardingcommand to enable multicast fast forwarding on an interface.
ip multicast-policy route-policy
Use the ip multicast-policy route-policycommand to enable a multicast policy routing on an
interface.
Interface view
System view
ip netstream aggregation
Use the ip netstream aggregationcommand to enter NetStream aggregation view.
ip netstream export host
Use the ip netstream export hostcommand to set the destination IP address and UDP port number for
NetStream UDP packets.
System view,
NetStream Aggregation view
ip netstream export source
Use the ip netstream export sourcecommand to configure a source interface for NetStream UDP
packets.
System view,
NetStream Aggregation view
ip netstream export version
Use the ip netstream export versioncommand to configure the type of AS numbers to be recorded in
NetStream cache entries and the version of UDP packets.
System view
System view
ip netstream format no-direction
Use the ip netstream format no-directioncommand to remove flow direction mark in the header of
NetStream log packet.
ip netstream { inbound | outbound }
Use the ip netstream{ inbound | outbound } command to enable NetStream statistics in the inbound
or outbound direction of the interface.
Interface view
System view
System view
ip netstream max-entry
Use the ip netstream max-entrycommand to set the NetStream cache size.
ip netstream timeout active
Use the ip netstream timeout activecommand to set the active aging timer for NetStream cache entries.
86
3Com Router 5000/6000 Family
Command Reference
ip netstream timeout inactive
Use the ip netstream timeout inactivecommand to set the inactive aging timer for NetStream cache
entries.
System view
ip option source-routing
Use the ip option source-routingcommand to enable IP source routing, allowing the router to handle
the packets with the IP source-route option.
System view
Interface view
ip policy route-policy
Use the ip policy route-policycommand to enable policy routing at an interface.
ip pool
Use the ip poolcommand to configure a local address pool for assigning addresses to PPP users.
System view
ISP Domain view
ip-precedence
Use the ip-precedencecommand to set the precedence of IP packets carried over PVC.
ATM PVC-Group view
ip relay address cycle
Use the ip relay address cyclecommand to enable the DHCP relay to allocate servers using the load
sharing approach, where the HASH algorithm applies allowing different clients to use different DHCP
servers and the same client to use the same DHCP server so long as it is possible.
System view
ip relay address (Interface view)
Use the ip relay address command to specify the exact location of a DHCP server by configuring an IP
relay address for it on the current interface.
Interface view
System view
ip relay address interface (System view)
Use the ip relay address interfacecommand to configure a relay address for the Ethernet interfaces
in a specified range for the purpose of transparent forwarding.
ip route-static
Use the ip route-staticcommand to configure a static route.
Use the ip route-static vpn-instancecommand to configure a static route. In the application of
multi-role host, you can configure a static route on a private network to specify the interface of another
private network or public network as its outbound interface.
System view
System view
ip route-static detect-group
Use the ip route-static detect-groupcommand to configure a static route and reference a detect group.
ip route-static vpn-instance
Use the ip route-static vpn-instancecommand to configure a static route, by specifying a private
network interface as the outgoing-interface of this static route.
System view
ip rpf-longest-match
ip rpf-route-static
Use the ip rpf-longest-matchcommand to configure the longest-match rule to be the multicast RPF route
selecting policy.
System view
System view
System view
Interface view
Interface view
Use the ip rpf-route-staticcommand to configure multicast static routes.
ip source-address-check
Use the ip source-address-checkcommand to enable source address check function for IP packets.
ip tcp vjcompress
Use the ip tcp vjcompresscommand to enable a PPP interface to compress the VJ TCP header.
ip urpf
Use the ip urpfcommand to enable URPF check on the interface.
3Com Router 5000/6000 Family
Command Reference
87
ip vpn-instance
Use the ip vpn-instancecommand to create and configure a vpn-instance.
Use the ip vpn-instancecommand to create a vpn-instance named vpn-name.
System view
Routing Protocol (BGP and RIP) view
ipsec card-proposal
Use the ipsec card-proposalcommand to create an SA proposal for the encryption card and enter the
corresponding view.
System view
ipsec policy (Interface view)
Use the ipsec policy(Interface view) command to apply an ipsec policy group with the name
policy-nameat the interface,.
Interface view
System view
ipsec policy (System view)
Use the ipsec policycommand to establish or modify an ipsec policy, and enter IPSec policy view.
ipsec policy-template
Use the ipsec policy-templatecommand to establish or modify an IPSec policy template, and enter
IPSec policy template view.
System view
ipsec proposal
Use the ipsec proposalproposal-namecommand to establish or modify a proposal named
proposal-name, and enter IPSec proposal view.
System view
System view
ipsec sa global-duration
Use the ipsec sa global-durationcommand to set a global SA duration.
ipv4-family
Use the ipv4-familycommand to enter IPv4 extended address family view of BGP.
Use the ipv4-family multicastcommand to multicast. For relevant contents, refer to "MBGP Multicast
Extended" chapter in module "Multicast" of this manual.
Use the ipv4-family vpn-instancecommand for BGP/MPLS VPN. For related description, refer to "MPLS
VPN" chapter in module "MPLS" module of this manual.
BGP view
VPN Instance view
ipv4-family
Use the ipv4-family multicastcommand to enter MBGP multicast address family view.
Use the ipv4-family vpn-instancecommand to enter MBGP vpn-instance address family view.
Use the ipv4-family vpnv4command to enter MBGP VPNv4 address family view.
BGP view
BGP view
RIP view
BGP view
ipv4-family multicast
Use the ipv4-family multicastcommand to enter the IPv4 multicast subaddress family view.
ipv4-family vpn-instance
Use the ipv4-familycommand to enter MBGP address family view of RIP.
ipv4-family vpnv4
idle-mark
Use the ipv4-family vpnv4command to enter VPNv4 address family view of BGP.
Use the idle-markcommand to configure the idle coding scheme of the synchronous serial port.
Synchronous Serial Interface view
ipx enable
Use the ipx enablecommand to activate IPX.
System view
ipx encapsulation
Use the ipx encapsulationcommand to set IPX frame encapsulation format on Ethernet interface.
Ethernet Interface view
88
3Com Router 5000/6000 Family
Command Reference
ipx netbios-propagation
Use the ipx netbios-propagationcommand to configure the router to forward type 20 broadcast packets
on the current interface.
Interface view
Interface view
ipx network
Use the ipx networkcommand to configure a network ID for an interface.
ipx rip import-route
Use the ipx rip import-route staticcommand to import static routes into RIP. RIP adds them in their
route updates.
System view
Interface view
System view
System view
ipx rip mtu
Use the ipx rip mtucommand to configure RIP updating packet size.
ipx rip multiplier
ipx rip timer update
Use the ipx rip multipliercommand to configure the aging period of RIP routing information table items.
Use the ipx rip timer updatecommand to configure RIP updating interval.
ipx route load-balance-path
Use the ipx route load-balance-pathcommand to configure the equivalent route number to the same
destination address.
System view
ipx route max-reserve-path
Use the ipx route max-reserve-pathcommand to configure the maximum dynamic route number to the
same destination address.
System view
System view
Interface view
Interface view
ipx route-static
ipx sap disable
Use the ipx route-staticcommand to configure IPX static route.
Use the ipx sap disablecommand to disable SAP on the current interface.
ipx sap gns-disable-reply
Use the ipx sap gns-disable-replycommand to disable IPX GNS reply on the current interface.
ipx sap gns-load-balance
Use the ipx sap gns-load-balancecommand to configure the router to respond GNS request in
Round-robin method, that is, all servers respond GNS request in turn.
System view
ipx sap max-reserve-servers
Use the ipx sap max-reserve-servers command to configure the length of the service information
reserve queue.
System view
Interface view
ipx sap mtu
Use the ipx sap mtucommand to configure the maximum size of SAP updating packet.
ipx sap multiplier
Use the ipx sap multiplier command to configure the aging period of SAP service information table
items.
System view
System view
System view
ipx sap timer update
Use the ipx sap timer updatecommand to configure SAP updating interval.
Use the ipx service commandto add a static service information item to SIT.
ipx service
3Com Router 5000/6000 Family
Command Reference
89
ipx split-horizon
Use the ipx split-horizoncommand to enable split horizon on the current interface.
Interface view
Interface view
ipx tick
Use the ipx tick command to configure the delay of interface sending IPX packets.
ipx update-change-only
Use the ipx update-change-onlycommand to enable trigger update on the current interface.
Interface view
is-level
Use the is-levelcommand to configure the IS-IS level.
IS-IS view
isdn bch-local-manage
isdn bch-select-way
isdn caller-number
isdn calling
Use the isdn bch-local-managecommand to enable local ISDN B channel management.
Use the isdn bch-select-way command to set a B channel selection method.
Use the isdn caller-numbercommand to configure the range of the numbers that the router can receive.
ISDN Interface view
ISDN Interface view
ISDN Interface view
Use the isdn callingcommand to have the messages from a calling party to a called party carry the calling
number.
ISDN Interface view
isdn check-called-number
Use the isdn check-called-numbercommand to configure the called number or subaddress that the
system should verify when receiving a digital call.
ISDN BRI Interface view
ISDN PRI Interface view
isdn crlength
Use the isdn crlengthcommand to set length of the call reference used when a call is placed on an ISDN
interface.
ISDN Interface view
isdn ie passthrough
Use the isdn ie passthroughcommand to enable transparent transmission of some or all related
information elements and you can use this command to configure transparent transmission direction.
ISDN Interface view (not applicable on BRI Interface)
isdn ignore connect-ack
Use the isdn ignore connect-ackcommand to configure the router to switch the ISDN protocol state to
ACTIVE to start the data and voice service communications after sending a CONNECT message without
having to wait for a CONNECT ACK message.
ISDN Interface view
ISDN Interface view
ISDN Interface view
isdn ignore hlc
isdn ignore llc
Use the isdn ignore hlccommand to disable ISDN to carry the higher layer compatibility (HLC)
information element in the SETUP messages sent when placing voice calls.
Use the isdn ignore llccommand to disable ISDN to carry the Lower Layer Compatibility (LLC)
information element in the SETUP messages sent when placing voice calls.
isdn ignore sending-complete
Use the isdn ignore sending-completecommand to configure the ISDN protocol to ignore the processing
on the Sending Complete Information Element.
ISDN Interface view
ISDN Interface view
isdn L3-timer
Use the isdn L3-timercommand to configure the duration of an ISDN L3 timer.
90
3Com Router 5000/6000 Family
Command Reference
isdn number-property
Use the isdn number-propertycommand to set the type and code scheme of calling or called numbers in
incoming or outgoing ISDN calls.
ISDN Interface view
isdn overlap-sending
Use the isdn overlap-sendingcommand to set the system to send the called number information in the
overlap mode on the ISDN interface.
ISDN Interface view
ISDN Interface View
Interface view
isdn q921-permanent
isdn pri-slipwnd-size
isdn protocol-mode
Use the isdn q921-permanentcommand to enable the Q.921 permanent link function.
Use the isdn pri-slipwnd-sizecommand to set the slide window size on a PRI interface.
Use the isdn protocol-modecommand to set the ISDN interface to operate on the user side or network
side of ISDN protocol.
ISDN Interface view
ISDN Interface view
isdn protocol-type
isdn send-restart
Use the isdn protocol-typecommand to set the ISDN protocol to be run on an ISDN interface.
Use the isdn send-restartcommand to enable PRI interfaces to actively send ISDN RESTART
messages to clear calls of the remote end before maintaining B channels.
System view
ISDN BRI Interface view
ISDN BRI Interface view
ISDN BRI Interface view
ISDN BRI Interface view
isdn spid auto_trigger
Use the isdn spid auto_triggercommand to enable SPID auto-negotiation once on the BRI interface
running the NI protocol.
isdn spid nit
isdn spid resend
isdn spid service
isdn spid timer
isdn spid1
Use the isdn spid nitcommand to set the SPID processing mode to NIT (Not Initial Terminal) on an
NI-compliant BRI interface.
Use the isdn spid resendcommand to set the number of INFORMATION message retransmission
attempts for SPID negotiation or initialization on an NI-compliant BRI interface.
Use the isdn spid servicecommand to configure the service types that must be supported in SPI
negotiation on the BRI interface adopting NI protocol.
Use the isdn spid timercommand to set the duration of the timer TSPID for an NI-compliant BRI interface
to timer_length.
ISDN BRI Interface view
Use the isdn spid1command to configure SPID information for the B1 channel on the NI-compliant BRI
interface.
ISDN BRI Interface view
isdn spid2
Use the isdn spid2command to configure SPID information for the B1 channel on an NI-compliant BRI
interface.
ISDN BRI Interface view
3Com Router 5000/6000 Family
Command Reference
91
isdn statistics
Use the isdn statisticscommand to have the system make statistics on the information received and
transmitted at an ISDN interface.
Use the isdn statistics startcommand in the view of an interface to start making statistics on the
messages received and transmitted at the interface.
Use the isdn statistics displaycommand to view the statistic information.
Use the isdn statistics continuecommand to continue the effort in making statistics.
Use the isdn statistics display flowcommand to view the statistics in the form of flow.
Use the isdn statistics stopcommand to stop making statistics.
ISDN Interface view
isdn two-tei
Use the isdn two-teicommand to have the router requests the connected switch for a new TEI value
before calling for a B channel.
BRI Interface view
System view
isis
Use the isiscommand to enable the corresponding IS-IS routing process and enter the IS-IS view.
isis authentication-mode
Use the isis authentication-modecommand to configure the IS-IS to authenticate the hello messages
of the corresponding level, in the specified mode and with the specified password on the IS-IS interface.
Interface view
Interface view
Interface view
isis circuit-level
isis cost
Use the isis circuit-levelcommand to configure the link adjacency relationship.
Use the isis costcommand to configure the link cost of this interface when performing SPF calculation.
isis dis-priority
Use the isis dis-prioritycommand to configure the priority of an interface for the corresponding level
DIS election.
Interface view
isis enable
Use the isis enablecommand to configure this interface to activate the corresponding IS-IS routing
process.
Interface view
Interface view
Interface view
isis enable clns
isis mesh-group
isis small-hello
Use the isis enable clnscommand to enable CLNS-based IS-IS routing process for a specified interface.
Use the isis mesh-groupcommand to add an interface to a specified mesh group.
Use the isis small-hellocommand to disable IS-IS to stuff Hello packets to the size of interface MTU if
their data sizes are smaller.
Interface view
Interface view
Interface view
Interface view
isis timer csnp
Use the isis timer csnp command to configure the interval of sending CSNP packets on the broadcast
network.
isis timer hello
Use the isis timer hellocommand to configure the interval of sending hello message of corresponding
level.
isis timer holding-multiplier
Use the isis timer holding-multiplier command to configure the number of invalid Hello messages
for the interface.
92
3Com Router 5000/6000 Family
Command Reference
isis timer lsp
Use the isis timer lspcommand to configure minimum IS-IS LSP interval on the interface.
Interface view
Interface view
isis timer retransmit
Use the isis timer retransmitcommand to configure the LSP retransmission interval over the
point-to-point link.
itf (CE1/PRI Interface)
Use the itfcommand to set the type of and the number of interframe filling tags on the CE1/PRI interface.
Two types of interframe filling tag are available: 0x7e and 0xff.
CE1/PRI Interface view
itf (CT1/PRI Interface)
Use the itfcommand to set the type of and the the number of interframe filling tags on the CT1/PRI
interface. Two types of interframe filling tag are available: 0x7e and 0xff.
CT1/PRI Interface view
HWPing Test Group view
HWPing Test Group view
jitter-interval
jitter-packetnum
keepalive
Use the jitter-intervalcommand to set a packet sending interval for a jitter test.
Use the jitter-packetnumcommand to configure the number of packets to be sent in a jitter test.
Use the keepalivecommand to enable the keepalive function of GRE and configure the interval for sending
keepalive messages and the maximum number of sending attempts as well.
Tunnel Interface view
language-mode
Use the language-modecommand to toggle the display language of the command line interface (CLI)
between English and Chinese.
User view
Interface view
Interface view
lapb max-frame
lapd modulo
Use the lapb max-framecommand to configure LAPB parameter N1.
Use the lapb modulocommand to specify the LAPB frame numbering view (also called modulo).
lapb pollremote
Use the lapb pollremotecommand to configure the link protocol to teardown the link in use after receiving
false packets.
Interface view
Interface view
Interface view
lapb retry
Use the lapb retrycommand to configure LAPB parameter N2.
lapd timer
Use the lapb timercommand to configure the LAPB timers T1, T2 and T3.
lapb window-size
Use the lapb window-sizecommand to configure the LAPB window
parameter K.
Interface view
PKI Domain view
FTP Client view
Local User view
ldap-server
Use the ldap-server ipcommand to configure the LDAP server IP address and the port.
Use the lcdcommand to get the local working directory path of the FTP client.
Use the levelcommand to configure user priority level.
lcd
level
3Com Router 5000/6000 Family
Command Reference
93
limit
Use the limitcommand to create rule under corresponding connection limit policy.
Connection Limit Policy view
POTS Voice Entity view
line
line
Use the linecommand to associate the voice entity with a specified voice subscriber-line.
Use the linecommand to configure the corresponding relationship between the POTS voice entity and the
logic subscriber line.
POTS Voice Entity view
link-protocol
Use the link-protocolcommand to set the link layer protocol of the interface.
POS Interface view
Interface view
link-protocol fr
link-protocol fr mfr
Use the link-protocol frcommand to encapsulate interface link layer protocol as Frame Relay.
Use the link-protocol fr mfrcommand to configure the current physical interface as an MFR bundle link
and bundle it onto a specified MFR interface.
Interface view
Interface view
Interface view
link-protocol hdlc
link-protocol lapb
link-protocol ppp
Use the link-protocol hdlccommand to configure the interface encapsulation as HDLC.
Use the link-protocol lapbcommand to specify the link layer protocol of the interface as LAPB.
Use the link-protocol pppcommand to configure the link-layer protocol encapsulated on the interface as
PPP.
Interface view
link-protocol sdlc
Use the link-protocol sdlccommand to change the link layer encapsulation protocol of the synchronous
serial interface into SDLC.
Synchronous Serial Interface view
link-protocol slip
link-protocol sot
link-protocol x25
llc2 max-ack
Use the link-protocol slipcommand to set the link layer protocol of the interface as SLIP.
Use the link-protocol sotcommand to encapsulate the serial interface with SOT.
Interface view
Synchronous Serial Interface view
Use the link-protocol x25command to encapsulate X.25 protocol to the specified interface.
Interface view
Use the llc2 max-ackcommand to configure the length of the advance response window before the LLC2
sending the acknowledgement frame.
Ethernet Interface view
Ethernet Interface view
Ethernet Interface view
Ethernet Interface view
llc2 max-send-queue
llc2 max-transmission
llc2 modulo
Use the llc2 max-send-queuecommand to configure the queue length sending the LLC2 packet.
Use the llc2 max-transmissioncommand to configure the retransmission times of the LLC2.
Use the llc2 modulocommand to configure the modulus of the LLC2.
94
3Com Router 5000/6000 Family
Command Reference
llc2 receive-window
Use the llc2 receive-windowcommand to configure the maximum packets that can be sent before the
LLC2 receives the acknowledgement frame.
Ethernet Interface view
llc2 timer ack
Use the llc2 timer ackcommand to configure the LLC2 local response time.
Ethernet Interface view
llc2 timer ack-delay
Use the llc2 timer ack-delaycommand to configure the local acknowledgement delay time when the
LLC2 receives information frames.
Ethernet Interface view
Ethernet Interface view
Ethernet Interface view
Ethernet Interface view
llc2 timer busy
llc2 timer poll
llc2 timer reject
loadbandwidth
local
Use the llc2 timer busycommand to configure the LLC2 BUSY time.
Use the llc2 timer pollcommand to configure the P/F waiting time of the LLC2.
Use the llc2 timer rejectcommand to configure the REJ time of the LLC2.
Use the loadbandwidthcommand to allocate load bandwidth to the interface.
Interface (Excluding Logical Interfaces) view
IKE-Peer view
Use the localcommand to configure the subnet type in IKE negotiation.
local-address
local-server
local-user
Use the local-addresscommand to configure the IP address of the local GW in IKE negotiation.
lUse the local-servercommand to configure a local RADIUS authentication server.
lUse the local-usercommand to configure the user name and password of a client.
Use the local-usercommand to add a local user and enter the local user view.
IKE-Peer view
System view
Dvpn-Class view
System view
local user
local-user password-display-mode
Use the local-user password-display-modecommand to configure the password display mode of all the
local users.
System view
locality
lock
Use the localitycommand to name the geographical locality of an entity, by a city for example.
PKI Entity view
Use the lockcommand to lock the active user interface and prevent unauthorized users from accessing it.
The active user interface can be console, AUX, or VTY.
User view
ASPF Policy view
BGP view
log enable
Use the log enablecommand to enable ASPF session logging function.
log-peer-change
log-peer-change
Use the log-peer-changecommand to turn on the BGP adjacency changes output switch.
Use the log-peer-changecommand to configure to log the IS-IS adjacency changes.
IS-IS view
3Com Router 5000/6000 Family
Command Reference
95
log-peer-change
Use the log-peer-changecommand to turn on the OSPF adjacency changes output switch for the current
OSPF process.
OSPF view
User view
log startup
loopback
loopback
loopback
loopback
Use the log startupcommand to turn on the configuration restoration log switch.
Use the loopbackcommand to enable the loopback function on an ATM OC-3c/STM-1 interface.
Use the loopbackcommand to configure the loopback mode on the ATM E1/T1 interface.
Use the loopbackcommand to enable loopback function of interface.
Use the loopbackcommand to enable a serial interface to perform loopback.
ATM Interface view
ATM E1/T1 Interface views
ATM E3/T3 Interface view
AM Interface view
AUX Interface view
Serial Interface view
loopback
loopback
loopback
loopback
Use the loopbackcommand to set the loopback mode on the interface.
CE1/PRI interface view
CPOS Interface view
Ethernet Port view
Use the loopbackcommand to configure the loopback function of the CPOS interface.
Use the loopbackcommand to enable loopback on the Ethernet port for test purpose.
Use the loopbackcommand to configure the loopback function of the POS interface.
POS Interface view
CE1/PRI Interface view
CE3 Interface view
loopback (CE1/PRI Interface)
Use the loopbackcommand to enable a CE1/PRI interface to perform loopback.
loopback (CE3 Interface)
Use the loopbackcommand to configure the loopback mode of a CE3 interface.
loopback (CT1/PRI Interface)
Use the loopbackcommand to enable a CT1/PRI interface to perform local, remote, or external payload
loopback.
CT1/PRI Interface view
loopback (CT3 Interface)
Use the loopbackcommand to configure the loopback mode of the CT3 interface.
CT3 Interface view
loopback (Ethernet/GE Interface)
Use the loopbackcommand to enable local loopback on the Ethernet interface.
Ethernet Interface view
loopback (ISDN BRI Interface)
Use the loopbackcommand to place the B1, B2, or both channels on the BRI interface in a remote looback.
This can send data from a line back to the line.
ISDN BRI Interface view
looptest
Use the looptestcommand to test whether an interface or line is in a loop.
Any view
lr
Use the lrcommand to configure LR.
Traffic Behavior view
96
3Com Router 5000/6000 Family
Command Reference
lr percent
1Use the lr percentcommand to configure LR.
Traffic Behavior view
FTP Client view
ls
Use the lscommand to query for a specified file/directory.
ls
Use the lscommand to view the files in the specified directory as you would with the dircommand.
Use the lsp-triggercommand to configure topology-triggered LSP creation policy.
Use the mac-addresscommand to configure Mac address of virtual Ethernet interface.
SFTP Client view
MPLS view
lsp-trigger
mac-address
mac-address timer aging
mandatory-chap
Virtual Ethernet Interface view
Use the mac-address timer agingcommand to set the aging timer for the MAC address table on the port.
Ethernet Port view
L2TP Group view
Use the mandatory-chapcommand to force LNS to perform CHAP authentication again with the client.
mandatory-lcp
Use the mandatory-lcpcommand to allow LNS and client to renegotiate Link Control Protocol (LCP)
between them.
L2TP Group view
PVC view
map bridge
map bridge-group
map clns
Use the map bridgecommand to establish the IPoEoA mapping or PPPoEoA mapping on the PVC.
Use the map bridge-group broadcastcommand to enable the PVC to transmit and receive BPDUs.
Use the map clnscommand to create a CLNSOA mapping for a PVC.
PVC view
ATM PVC view
PVC view
map ip
Use the map ipcommand to create IPoA mapping for PVC.
map ppp
Use the map pppcommand to create a PPPoA map on the PVC.
PVC view
map routed-bridge
Use the map routed-bridgecommand to configure routed bridge encapsulation on the PVC.
ATM PVC view
match
Use the matchcommand to configure a PVC group to differentiate traffic by the Precedence or DSCP
identifier in the TOS field of the IP header.
ATM Pvc-Group view
Voice Entity view
match-template
Use the match-templatecommand to configure the match template for a voice entity.
max-call (in Voice Dial Program View)
Use the max-callcommand to configure max-call sets (128 sets at most).
Voice Dial Program view
Voice Entity view
max-call (in Voice Entity View)
Use the max-callcommand to bind a voice entity to the max-call set specified by set-number.
3Com Router 5000/6000 Family
Command Reference
97
max-packet-process
Use the max-packet-processcommand to set the maximum number of processed packets per second on
a certain VLAN.
System view
md5-compatible
Use the md5-compatiblecommand to configure ISIS to use the 3Com-compatible MD5 algorithm. You
need to use this command when MD5 authentication on ISIS is required between your router and a 3Com
device.
ISIS view
CT3 Interface view
System view
mdl (CT3 Interface)
Use the mdlcommand to configure MDL message detection/sending on the CT3 interface.
Use the memorycommand to configure the safety value and lower limit of the router idle memory.
memory
memory auto-establish disable
Use the memory auto-establish disablecommand to disable the function of restoring the connections of
all the routing protocols (even if the idle memory reduces to a safety value).
Use the memory auto-establish disablecommand to disable the above function.
System view
memory auto-establish enable
Use the memory auto-establish enablecommand to resume connections of all the routing protocols when
the idle memory of the router recovers to a safety value.
Use the memory auto-establish disablecommand to disable the above function. Use the memory
auto-establish enablecommand to enable the above function again. By default, the function is always
enabled.
System view
R2 CAS view
mfc (R2 CAS)
Use the mfccommand to maintain of MFC channel of the specified timeslot.
Use the mfr bundle-namecommand to set frame relay bundle identification (BID).
Use the mfr fragmentcommand to enable FRF.16 fragmentation on the MFR bundle.
mfr bundle-name
mfr fragment
MFR Interface view
MFR Interface view
mfr fragment-size
Use the mfr fragment-sizecommand to configure the maximum fragment size allowed on a frame relay
bundle link.
Frame Relay Interface view
MFR Interface view
mfr link-name
mfr retry
Use the mfr link-namecommand to set the frame relay bundle link identification (LID).
Frame Relay Interface view
Use the mfr retrycommand to set the maximum times that a frame relay bundle link can resend hello
message when waiting for a hello acknowledgement message.
Frame Relay Interface view
mfr timer ack
Use the mfr timer ackcommand to set the time of waiting for hello acknowledgment message before
frame relay bundle link resends hello message.
Frame Relay Interface view
mfr timer hello
mfr window-size
Use the mfr timer hellocommand to set the interval for a frame relay bundle link to send hello message.
Frame Relay Interface view
Use the mfr window-sizecommand to configure the number of fragments that can be held by the window
used in sliding window algorithm when multilink frame relay reassembles received fragments.
MFR Interface view
98
3Com Router 5000/6000 Family
Command Reference
min-active-links
Use the min-active-links command to configure the minimum number of available links required for the
IMA group to operate.
IMA Group Interface view
mkdir
Use the mkdircommand to create a directory on the remote FTP server.
Use the mkdir command to create a directory on the remote SFTP server.
FTP Client view
mkdir
SFTP Client view
mkdir
Use the mkdircommand to create a directory under the specified directory on the specified storage device.
Use the mobile-ipcommand to enable the MIP function.
User view
System view
System view
Interface view
System view
mobile-ip
mobile-ip foreign-agent
Use the mobile-ip foreign-agentcommand to set foreign agent care-of addresses and the pending time.
mobile-ip foreign-agent service
Use the mobile-ip foreign-agent servicecommand to enable FA service on an interface.
mobile-ip home-agent
Use the mobile-ip home-agentcommand to enable HA service on a router.
mobile-ip home-agent mobile-router
Use the mobile-ip home-agent mobile-routercommand to configure an MR on an HA. This command
will bring you to HA-MR view.
System view
Interface view
System view
mobile-ip irdp
Use the mobile-ip irdpcommand to enable IRDP and configure the relevant attributes on an interface.
mobile-ip mobile-router
Use the mobile-ip mobile-routercommand to enable the MR function and enter MR view.
mobile-ip mobile-router ccoa
Use the mobile-ip mobile-router ccoa onlycommand to specify that the interface can only use a
co-located care-of address to register.
Use the mobile-ip mobile-router ccoa only gatewaycommand to configure the default gateway for the
interface using a co-located care-of address to register.
Interface view
Interface view
Interface view
mobile-ip mobile-router roam
Use the mobile-ip mobile-router roamcommand to enable the roaming function on the interface, that
is, to allow the interface to function as the roaming interface of the MR.
mobile-ip mobile-router solicit
Use the mobile-ip mobile-router solicitcommand to configure agent solicitation retransmission
parameters.
mobile-ip prefix-length
Use the mobile-ip prefix-lengthcommand to add the prefix-length extension part in the agent
advertisement.
Interface view
Interface view
System view
mobile-ip registration-lifetime
Use the mobile-ip registration-lifetimecommand to set the registration lifetime of the MN.
mobile-ip secure
Use the mobile-ip securecommand to configure mobility security associations on HAs, FAs, and MRs.
3Com Router 5000/6000 Family
Command Reference
99
mobile-ip tunnel path-mtu-discovery
Use the mobile-ip tunnel path-mtu-discoverycommand to set the PMTU update policy.
System view
System view
HA-MR view
MR view
mobile-ip virtual-network
Use the mobile-ip virtual-networkcommand to define a virtual network.
mobile-network
mobile-network
mobile-node
Use the mobile-networkcommand to configure a mobile network for an MR.
Use the mobile-networkcommand to configure a mobile network for the MR.
Use the mobile-nodecommand to set MN attributes, including the interface or virtual network and the
registration lifetime.
System view
R2 CAS view
SIP Client view
mode
Use the modecommand to configure the R2 signaling mode in a country or region.
mode (SIP Client view)
Use the modecommand to set the registration mode of the gateway.
modem
Use the modemor modem bothcommand to allow modem calls to pass through, both incoming and outgoing.
Use the modem[ call-in | call-out ]command to allow incoming or outgoing modem calls to pass
through.
User Interface view
User Interface view
modem adapt no-waiting-connect
Use the modem adapt no-waiting-connect command to set the asynchronous serial interface Modem to
switch from IDLE to ACTIVE without waiting for receiving the signal CONNECT (a signal used for a physical
modem to negotiation rate) after it receives CD_UP (a lower layer detects carrier signal).
modem auto-answer
modem auto-answer
Use the modem auto-answercommand to have the external modem connected to the asynchronous
interface automatically answer or hook off.
User Interface view
User Interface view
Use the modem auto-answercommand to set the answering mode to auto-answer.
modem compatible-param
Use the modem compatible-paramcommand in the case that you fail to use standard Modem PCM to
interoperate with devices from other vendors.
Voice Entity view
modem protocol
Use the modem protocol noneprotocol to disable Modem function for single voice entity.
Use the modem protocol pcmcommand to configure PCM Modem protocol type for single voice entity,
including coding/decoding and Modem negotiation mode.
Voice Entity view
modem timer answer
Use the modem timer answercommand to set the timeout time spent waiting for the carrier signal after the
off-hook action when setting up an incoming call connection.
User Interface view.
monitor-port
Use the monitor-portcommand to specify the current port as the monitoring port
Ethernet Interface view
User view
more
Use the morecommand, you can view the contents of the specified file.
100
3Com Router 5000/6000 Family
Command Reference
motorola base-svc
Use the motorola base-svccommand to configure the start SVC for voice routing on a DLCI.
DLCI view
DLCI view
motorola encapsulation
Use the motorola encapsulationcommand to specify an encapsulation for Motorola LCON on the DLCI.
motorola max-voice
Use the motorola max-voicecommand to configure the maximum number of voice channels created on a
DLCI concurrently.
DLCI view
DLCI view
User view
motorola remote-id
Use the motorola remote-idcommand to configure a remote connection ID.
Use the movecommand to move a file.
move
mpls
Use the mplscommand in system view to enable MPLS globally and enter MPLS view.
Use the mplscommand in interface view to enable MPLS on the interface.
Interface view
Routing Protocol view
System view
Virtual Interface view
mpls l2vc
Use the mpls l2vccommand to create an LDP connection.
Use the mpls l2vpncommand to enable L2VPN.
Interface view
System view
mpls l2vpn
mpls l2vpn encapsulation
Use the mpls l2vpn encapsulationcommand to create Kompella MPLS L2VPN, specify encapsulation
type, and enter MPLS L2VPN view.
System view
mpls-exp
Use the mpls-expcommand to configure the PVC to carry packets of the specified priority levels when the
EXP identifier in the MPLS packet is used to identify the priority levels of packets.
ATM Pvc-Group view
mpls label advertise
Use the mpls label advertisecommand to specify at the egress the type of the label to be distributed to
the penultimate hop.
MPLS view
System view
Interface view
System view
System view
mpls ldp
Use the mpls ldpcommand to enable LDP.
mpls ldp enable
mpls ldp hops-count
mpls ldp loop-detect
mpls ldp password
Use the mpls ldp enablecommand to enable LDP on the interface.
Use the mpls ldp hops-countcommand to set the maximum hops of loop detection.
Use the mpls ldp loop-detectcommand to enable loop detection.
Use the mpls ldp passwordcommand to configure LDP authentication mode.
Interface view
Remote-Peer view
3Com Router 5000/6000 Family
Command Reference
101
mpls ldp path-vectors
Use the mpls ldp path-vectorscommand to set the maximum value of path vector.
System view
mpls ldp remote-peer
Use the mpls ldp remote-peercommand to create a remote-peer entity and enter remote-peer view.
Remote-Peer view
System view
mpls ldp reset-session
Use the mpls ldp reset-sessioncommand to reset a specified session on an interface.
Interface view
mpls ldp timer
Use the mpls ldp timercommand to set the duration of a Hello hold timer or session hold timer.
Interface view
Remote-Peer view
mpls ldp transport-ip
mpls lsr-id
mpls static-l2vc
msdp
Use the mpls ldp transport-ipcommand to configure an LDP session transport address.
Interface view
System view
Use the mpls lsr-id command to configure an LSR ID.
Use the mpls static-l2vccommand to create an SVC MPLS L2VPN connection.
Use the msdpcommand to enable MSDP and enter the MSDP view.
Interface view
System view
msdp-tracert
Use the msdp-tracertcommand to trace the transmission path of SA messages in the network.
Use the mtucommand to set the size of Maximum Transmission Unit (MTU) of the ATM interface.
Use the mtucommand to configure MTU of Kompella MPLS L2VPN.
Any view
mtu
Interface view
mtu
MPLS L2VPN view
Interface view
mtu (ATM Interface)
Use the mtucommand to set the MTU size of the ATM interface.
mtu (Ethernet/GE Interface)
Use the mtucommand to set the MTU size of the Ethernet interface.
Ethernet Interface view
mtu label-including
mtu (POS Interface)
Use the mtu label-includingcommand to configure to include MPLS label length in outgoing interface
MTU calculation.
MPLS view
Use the mtucommand to set the MTU size of the POS interface.
POS Interface view
mtu (serial interface)
Use the mtucommand to set MTU of the serial interface.
AM Interface view
AUX Interface view
Serial Interface view
mtu (Tunnel Interface)
Use the mtucommand to set the maximum transmission unit (MTU) for Tunnel interface.
Tunnel Interface view
102
3Com Router 5000/6000 Family
Command Reference
mtracert
Use the mtracertcommand to trace the network path from the multicast source to the destination receiver
along Multicast Distribution Tree, according to either the multicast kernel routing table or RPF rule to the
source.
Any view
OSPF view
multi-path-number
Use the multi-path-numbercommand to configure maximum number of OSPF equal-cost routes.
Use the multicast minimum-ttlcommand to configure the minimum TTL value for multicast forwarding.
multicast minimum-ttl
Interface view
Interface view
multicast packet-boundary
Use the multicast packet-boundarycommand to configure a multicast forwarding boundary.
multicast route-limit
Use the multicast route-limitcommand to limit the multicast routing table capacity. If the capacity
exceeds the limit, the router will discard protocols and data packets of the newly-added (S, G).
System view
System view
multicast routing-enable
Use the multicast routing-enablecommand to enable IP multicast routing.
multiplex mode
Use the multiplex modecommand to set AUG multiplexing mode.
CPOS Interface view
nas-ip
Use the nas-ipcommand to set the source IP address of the network access server (NAS, the router in this
manual), so that all packets destined for the RADIUS server carry the same source IP address.
RADIUS view
nas-ip
Use the nas-ipcommand to have all the TACACS+ packets sent by the NAS (the router) carry the same
source address.
TACACS+ view
System view
System view
System view
System view
nat address-group
nat aging-time
nat agl
Use the nat address-groupcommand to configure an address pool.
Use the nat aging-timecommand to set the lifetime of NAT connections.
Use the nat algcommand to enable the application gateway function of NAT.
nat connection-limit-policy
Use the nat connection-limit-policycommand to specify the NAT connection limit policy.
nat dns-map
nat oubound
Use the nat dns-mapcommand to configure a NAT entry, mapping a domain name to a triplet of external
IP address, port number, and protocol type.
System view
Interface view
Use the nat outboundcommand to associate an ACL with an address pool, indicating that the address
specified in the acl-numbercan be translated by using address pool group-number.
nat outbound interface
Use the nat outbound interfacecommand to associate an ACL with an interface and to use the address
of the interface as the target address in the translations for the packets matching the ACL. After that, this
address substitutes for the source addresses of the packets matching the ACL.
Interface view
3Com Router 5000/6000 Family
Command Reference
103
nat outbound static
Use the nat outbound staticcommand to apply on the interface one-to-one address translation
configured using the nat static command.
Interface view
System view
nat overlapaddress
nat server
Use the nat overlapaddresscommand to map an overlapping address pool to a temporary address pool.
Use the nat servercommand to define a mapping table for internal servers. Users can access the internal
server with the address and port as host-addr and host-port respectively through the address port defined
by global-addr and global-port.
Interface view
System view
nat static
Use the nat staticcommand to configure a one-to-one private-to-public address binding.
nat static inside
Use the nat static inside command to create a static net-to-net NAT entry. When the router translates
addresses based on this type of NAT entry, it translates the network address portion without touching the
host address portion.
System view
IKE-Peer view
nat traversal
national-bit
naturemask-arp
Use the nat traversalcommand to configure the NAT traversal function of IKE/IPSec.
Use the national-bitcommand to configure national bit on the CE3 interface.
CE3 Interface view
Use the naturemask-arp enablecommand to support ARP within natural network segments rather than
subnets.
System view
nbns-list
Use the nbns-listcommand to configure NetBIOS server addresses in a global DHCP address pool for
the clients.
DHCP Address Pool view
nesting
Use the nestingcommand to configure a nesting rule.
ACL view
netbios-type
Use the netbios-typecommand to configure the NetBIOS node type of the clients of a global DHCP
address pool.
DHCP Address Pool view
network
network
network
network
network
Use the networkcommand to configure the network routes advertised by the local BGP system.
Use the networkcommand to configure an IP address range used for dynamic allocation.
Use the networkcommand to configure the network addresses to be sent by the local BGP.
BGP view
DHCP Address Pool view
IPv4 Multicast Subaddress Family view
OSPF Area view
Use the networkcommand to configure the interface running OSPF.
Use the networkcommand to enable Routing Information Protocol (RIP) on the interface.
RIP view
104
3Com Router 5000/6000 Family
Command Reference
network-entity
Use the network-entitycommand to configure the name of Network Entity Title (NET) of the IS-IS routing
process.
IS-IS view
normal-connect slow-h245
Use the normal-connect slow-h245command to configure disabling the calling end from actively initiating
an H245 connection request to the called end before the called end is hooked off in voice entity view.
Use the normal-connect slow-h245 command to disable the calling end from actively initiating an H245
connection request to the called end before the called end is hooked off in voice entity view.
VoIP Voice Entity view
nslookup type
Use the nslookup typecommand to resolve the specified IP address or domain name to a domain name
or IP address.
Any view
OSPF Area view
System view
nssa
Use the nssacommand to configure an area as NSSA area.
Use the ntp-service accesscommand to control access to the NTP service on the local device.
ntp-service access
ntp-service authentication enable
Use the ntp-service authentication enablecommand to enable NTP service ID authentication.
System view
ntp-service authentication-keyid
Use the ntp-service authentication-keyidcommand to set an NTP authentication key.
System view
ntp-service broadcast-client
Use the ntp-service broadcast-clientcommand to configure NTP broadcast client mode.
Interface view
Interface view
ntp-service broadcast-server
Use the ntp-service broadcast-servercommand to configure NTP broadcast server mode.
ntp-service max-dynamic-sessions
Use the ntp-service max-dynamic-sessionscommand to set the number of sessions allowed by the local
device.
System view
Interface view
Interface view
ntp-service multicast-client
Use the ntp-service multicast-clientcommand to configure NTP multicast client mode.
ntp-service multicast-server
Use the ntp-service multicast-servercommand to configure NTP multicast server mode.
ntp-service refclock-master
Use the ntp-service refclock-mastercommand to set the local clock as the NTP master clock to provide
synchronization source.
System view
System view
ntp-service reliable authentication-keyid
Use the ntp-service reliable authentication-keyid command to specify a reliable key.
ntp-service source-interface
Use the ntp-service source-interfacecommand to specify an interface for the local end to transmit NTP
messages.
System view
System view
System view
ntp-service unicast-peer
Use the ntp-service unicast-peercommand to configure NTP peer mode.
ntp-service unicast-server
Use the ntp-service unicast-servercommand to configure NTP server mode.
3Com Router 5000/6000 Family
Command Reference
105
number-match
Use the number-matchcommand to configure a global number match-policy.
Voice Dial Program view
number-substitute
oam ais-rdi
Use the number-substitutecommand to create a number-substitute list and enter voice dial program view.
Voice Dial Program view
Use the oam ais-rdicommand to change the parameters related to AIS/RDI alarm cell detection. If no
argument is specified, the default value applies.
ATM Class view
PVC view
oam frequency
Use the oam frequencycommand to enable the transmission of OAM F5 Loopback cell so as to check the
PVC status. You can also enable OAM F5 Loopback retransmission check or modify the related parameters
of the retransmission check.
ATM Class view
PVC view
oamping interface
Use the oamping interfacecommand to enable the specified ATM interface to send OAM cells on the
specified PVC for checking link state. Receiving no response upon expiration of the specified time indicates
that the link is disconnected, busy, or prone to packet loss.
ATM Interface view
OSPF view
opaque-capability
Use the opaque-capability enablecommand to enable the Opaque capability of OSPF.
Use the opencommand to set up control connection to the remote FTP server.
Use the open-trunkcommand to enable E&M non-signaling mode.
open
FTP Client view
open-trunk
Analog E&M Voice Subscriber Line view
option
Use the optioncommand to configure the self-defined options for a DHCP global address pool.
DHCP Address Pool view
PKI Entity view
organization
organizational-unit
Use the organizationcommand to specify the name of the organization to which the entity belongs.
Use the organizational-unitcommand to specify the name of the organization unit to which this entity
belongs.
PKI Entity view
MSDP view
originating-rp
Use the originating-rpcommand to allow a MSDP to use the IP address of specified interface as the RP
address in the SA message originated.
osm connect slot
Use the osm connect slotcommand to connect the current control terminal to the OSM board to manage
the system on the OSM board. If you want to return from the OSM board to the operation interface on the
router, click hot key <Ctrl+k>.
User view
User view
User view
osm reboot slot
osm reload slot
osm shutdown slot
Use the osm reboot slotcommand to reset the OSM board.
Use the osm reload slotcommand to restart the operation system on OSM board.
Use the osm shutdown slotcommand to shut down the operation system on OSM board. This operation
equals to execute the turn off command on the operation system of OSM board.
User view
106
3Com Router 5000/6000 Family
Command Reference
ospf
Use the ospfcommand to enable the OSPF protocol.
System view
ospf authentication-mode
Use the ospf authentication-modecommand to configure the authentication mode and key between
adjacent routers.
Interface view
Interface view
ospf cost
Use the ospf costcommand to configure different packet sending costs so as to send packets from
different interfaces.
ospf dr-priority
Use the ospf dr-prioritycommand to configure the priority for electing the "designated router" on an
interface.
Interface view
System view
Interface view
Interface view
Interface view
ospf mib-binding
ospf mtu-enable
ospf network-type
ospf timer dead
ospf timer hello
Use the ospf mib-bindingcommand, MIB operation can be bound on the specified OSPF process.
Use the ospf mtu-enablecommand to enable the interface to write MTU value when sending DD packets.
Use the ospf network-typecommand to configure the network type of OSPF interface.
Use the ospf timer deadcommand to configure the dead interval of the OSPF neighbor.
Use the ospf timer hellocommand to configure the interval for transmitting Hello messages on an
interface.
Interface view
ospf timer poll
Use the ospf timer pollcommand to configure the poll Hello message interval on nbma and p2mp
network.
Interface view
Interface view
Interface view
System view
ospf timer retransmit
ospf trans-delay
ospf vpn instance
option
Use the ospf timer retransmitcommand to configure the interval for LSA re-transmitting on an interface.
Use the ospf trans-delaycommand to configure the LSA transmitting delay on an interface.
Use the ospfcommand to enable an OSPF process.
Use the optioncommand to specify the logical relationship between the addresses to be probed in the
detect group.
Detect Group view
Voice Entity view
Voice Entity view
outband
Use the outbandcommand to configure transmission of DTMF code in the outband mode.
Use the outband vofrcommand to configure out-of-band transmission of DTMF codes.
outband vofr
overlap voip h323
Use the overlap voip h323command to configure the calling party to support h323 overlap mode for
sending numbers.
Voice Dial Program view
3Com Router 5000/6000 Family
Command Reference
107
packing timer
Use the packing-timercommand to set the maximum waiting time for one PVC.
PVC view
User view
pad
Use the padcommand to establish a PAD connection with the remote site.
Use the pad-mode pos enablecommand to enable POSPAD access mode.
Use the paritycommand to set the check bit of the user interface.
Use the passivecommand to set data transmission mode to passive.
pad-mode pos enable
Synchronous Serial Interface view
User Interface view
parity
passive
FTP Client view
password
Use the passwordcommand to configure the password required for logging onto the FTP server.
Use the passwordcommand to configure a password for a local user.
HWPing Test Group view
Local User view
password
password-digit
Use the password-digitcommand to configure the user password digits of a certain access service
number in the card number process.
Voice Access-Number view
payload-size
Use the payload-sizecommand to notify the underlying layer how much time DSP spends assembling a
voice packet, or the time length of each voice packet.
Voice Entity view
pcm
Use the pcmcommand to configure a companding law used for quantizing signals.
Voice Subscriber-Line view
peer
Use the peercommand to configure the destination address of the peer to which information is sent in
unicast mode.
RIP view
peer
peer
Use the peercommand to configure an MSDP peer.
MSDP view
Use the peercommand to configure the IP address of adjacent routers and specify a DR priority on an
NBMA network.
OSPF view
peer
Use the peercommand to configure the subnet type in IKE negotiation.
IKE-Peer view
peer advertise-community
Use the peer advertise-communitycommand to enable the transmission of community attributes to a peer
group.
BGP view
VPNv4 view
VPN Instance view
peer advertise-community
Use the peer advertise-communitycommand to configure to advertise community attributes to a peer
(group).
IPv4 Multicast Subaddress Family view
108
3Com Router 5000/6000 Family
Command Reference
peer allow-as-loop
Use the peer allow-as-loopcommand to configure the repeating times of the local AS number.
BGP view
VPNv4 view
VPN Instance view
peer allow-as-loop
Use the peer allow-as-loopcommand to allow the AS_PATH attribute in the received routes to include
the local AS number.
IPv4 Multicast Subaddress Family view
peer as-number
Use the peer as-numbercommand to specify an AS number for a peer group.
BGP view
peer as-path-acl
Use the peer as-path-aclcommand to specify BGP route filtering policy based on AS path list for a
peer/peer group.
BGP view
VPNv4 view
VPN Instance view
peer as-path-acl
Use the peer as-path-acl importcommand to have MBGP filter the routes received from the specified
peer or peer group based on the specified AS path list.
Use the peer as-path-acl exportcommand to have MBGP filter the routes advertised to the specified
peer or peer group.
IPv4 Multicast Subaddress Family view
peer connect-interface
Use the peer connect-interfacecommand to specify the source interface for route updates.
BGP view
BGP view
peer default-route-advertise
Use the peer default-route-advertisecommand to redistribute a default route to a peer group.
peer default-route-advertise
Use the peer default-route-advertisecommand to enable a peer (group) to import a default route.
BGP view
MBGP IPv4-Family view
peer description
peer description
peer ebgp-max-hop
Use the peer descriptioncommand to configure the description information of the peer/peer group.
Use the peer descriptioncommand to configure descriptive text to MSDP peer.
BGP view
MSDP view
Use the peer ebgp-max-hopcommand to allow establishing EBGP connection with a neighbor on an
indirectly connected network.
BGP view
peer enable
Use the peer enablecommand to enable the specified peer (group).
BGP Unicast Address Family view
L2VPN Address Family view
IPv4 Multicast Sub-address Family view
VPNv4 Address Family view
peer enable
peer enable
Use the peer enablecommand to enable the multicast peer or peer group.
IPv4 Multicast Subaddress Family view
Use the peer enablecommand to activate the specified peer (group) in L2VPN address family view.
L2VPN Address Family view
3Com Router 5000/6000 Family
Command Reference
109
peer filter-policy
Use the peer filter-policy importcommand to configure BGP to filter routes received from the peer
(group) based on the ACL.
Use the peer filter-policy exportcommand to configure BGP to filter routes advertised to the peer
(group) based on the ACL.
BGP view
IPv4 Multicast Sub-Address Family view
peer filter-policy
Use the peer filter-policy importcommand to have MBGP filter the routes received from the specified
peer or peer group based on the specified ACL.
Use the peer filter-policy exportcommand to have MBGP filter the routes advertised to the specified
peer or peer group based on the specified ACL.
IPv4 Multicast Subaddress Family view
peer group
Use the peer groupcommand to add a peer to a peer group.
BGP view
peer ip-prefix
Use the peer ip-prefix importcommand to configure BGP to filter routes received from the peer/peer
group based on the ip-prefix list.
Use the peer ip-prefix exportcommand to configure BGP to filter routes advertised to the peer/peer
group based on the ip-prefix list.
BGP view
VPNv4 view
VPN Instance view
peer ip-prefix
Use the peer ip-prefix importcommand to have MBGP filter the routes received from the specified peer
or peer group based on the specified address prefix list.
Use the peer ip-prefix exportcommand to have MBGP filter the routes advertised to the specified peer
or peer group based on the specified address prefix list.
IPv4 Multicast Subaddress Family view
peer label route-capability
Use the peer label-route-capabilitycommand to enable the capability of a peer to process IPv4 routes
with labels.
BGP view
peer mesh-group
peer minimum-ttl
Use the peer mesh-groupcommand to configure an MSDP peer to join an Mesh Group.
MSDP view
Use the peer minimum-ttlcommand to configure the minimum TTL (Time-to-Live) value of the multicast
data packets encapsulated in SA messages to be sent to specified MSDP peer.
MSDP view
peer next-hop-invariable
Use the peer next-hop-invariablecommand to configure the invariable next hop when sending routes
to EBGP peers.
BGP view
BGP VPN-Instance view
BGP-VPNv4 Subaddress Family view
BGP-IPv4 Multicast Subaddress Family view
peer next-hop-local
peer next-hop-local
peer password
Use the peer next-hop-localcommand to configure the next hop in the route to be advertised to the peer
group as the address of the local router.
BGP view
Use the peer next-hop-localcommand to remove the processing of the next hop in routes which BGP
will advertise to the peer (group) and set the local address as the next hop.
IPv4 Multicast Subaddress Family view
Use the peer passwordcommand to configure BGP to perform MD5 authentication before setting up a TCP
connection.
BGP view
MBGP VPN-Instance Address Family view
110
3Com Router 5000/6000 Family
Command Reference
peer public-as-only
Use the peer public-as-onlycommand to configure not to carry the private AS number when transmitting
BGP updates.
BGP view
peer public-as-only
Use the peer public-as-onlycommand to configure only to carry public AS number rather than private
AS number when BGP sends update packets.
IPv4 Multicast Subaddress Family view
peer-public-key end
peer reflect-client
Use the peer-public-key endcommand to return to system view from public key view.
Public Key view
Use the peer reflect-clientcommand to configure a peer group as the route reflector client.
Use the peer reflect-clientcommand to configure a peer (group) as a client of the route reflector.
BGP view
VPNv4 view
peer reflect-client
IPv4 Multicast Subaddress Family view
peer request-sa-enable
Use the peer request-sa-enable command to enable the router to send SA request message to the
specified MSDP peer when receiving a new group join message.
MSDP view
peer route-policy
Use the peer route-policy importcommand to configure MBGP to filter routes received from the peer
(group) based on the route-policy.
Use the peer route-policy exportcommand to configure MBGP to filter routes advertised to the peer
(group) based on the route-policy.
BGP view
VPNv4 view
VPN Instance view
peer route-policy
Use the peer route-policy importcommand to have MBGP apply the specified routing policy to the
routes received from the specified peer or peer group.
Use the peer route-policy exportcommand to have MBGP apply the specified routing policy to the
routes advertised to the specified peer or peer group.
IPv4 Multicast Subaddress Family view
peer route-update-interval
Use the peer route-update-intervalcommand to configure the interval for a peer group to advertise
route updates.
BGP view
VPNv4 view
VPN Instance view
peer sa-cache-maximum
Use the peer sa-cache-maximumcommand to limit the number of caches originated when the router
receives SA messages from an MSDP peer.
MSDP view
MSDP view
MSDP view
peer sa-policy
Use the peer sa-policycommand to configure a filter list for SA messages received or forwarded from the
specified MSDP peer.
peer sa-request-policy
Use the peer sa-request-policycommand to limit SA request messages that the router receives from
MSDP peers.
peer shutdown
Use the peer shutdowncommand to disable the specified BGP peer or peer group to initiate or receive BGP
connection or to disconnect a BGP connection that has existed.
BGP view
VPN Instance view
3Com Router 5000/6000 Family
Command Reference
111
peer timer
Use the peer timercommand to configure Keepalive and Holdtime intervals for a peer (group).
BGP view
BGP view
peer upe
Use the peer upecommand to configure BGP peer as the UPE of hierarchical BGP/MPLS VPN.
Use the permanent-activecommand to configure BSV interfaces to permanent active.
permanent-active
BSV Interface view (in NTmode)
pfs
Use the pfscommand to set the Perfect Forward Secrecy (PFS) feature for the IPSec policy to initiate the
negotiation.
IPSec Policy view
IPSec Policy Template view
phy-mru
Use the phy-mrucommand to configure in asynchronous flow mode MRU at the physical layer.
Asynchronous Serial Interface view
physical-mode
Use the physical-modecommand to set the operating mode of the synchronous/asynchronous serial
interface.
Serial Interface view
System view
pim
Use the pimcommand to enter PIM view.
pim bsr-boundary
Use the pim bsr-boundarycommand to configure an interface to become the PIM domain boundary.
Use the pim dmcommand to enable PIM-DM.
Interface view
Interface view
pim dm
pim neighbor-limit
Use the pim neighbor-limitcommand to limit PIM neighbor number on an router interface. If the number
exceeds the limit configured, no new neighbor can be added to the router.
Interface view
pim neighbor-policy
Use the pim neighbor-policycommand to configure a router to filter the PIM neighbor of the current
interface.
Interface view
Interface view
Interface view
Any view
pim sm
Use the pim smcommand to enable PIM-SM protocol on an interface.
pim timer hello
Use the pim timer hellocommand to configure the interval for sending PIM router Hello messages.
Use the pingcommand to test connectivity of an IP network and reachability of a host.
Use the ping clnscommand to test the reachability to a specified destination.
ping
ping clns
ping ipx
Any view
Use the ping ipxcommand to check host reachability and network connectivity in IPX network.
Any view
pki delete-certificate
Use the pki delete-certificatecommand to delete the locally stored certificates.
System view
112
3Com Router 5000/6000 Family
Command Reference
pki domain
Use the pki domaincommand to enter PKI domain view, and configure the parameters of LDAP server and
for certificate request and authentication.
System view
Any view
pki entity
Use the pki entitycommand to name a PKI entity and enter PKI entity view.
pki import-certificate
Use the pki import-certificatecommand to import an existing CA certificate or local certificate.
System view
pki request-certificate
Use the pki request-certificatecommand to deliver certificate request through SCEP to CA for the
generated RSA key pair.
System view
System view
pki retrieval-certificate
Use the pki retrieval-certificatecommand to download a certificate from the certificate issuing server.
pki retrieval-crl
Use the pki retrieval-crlcommand to obtain the latest CRL from CRL server for the verification of the
validity of a current certificate.
System view
System view
pki validate-certificate
Use the pki validate-certificatecommand to verify the validity of a certificate.
plan-numbering
Use the plan-numberingcommand to configure the calling/called numbering plan attribute of voice entities.
Voice Entity view
play stop-accounting-buffer
Use the display stop-accounting-buffercommand to view information on the stop-accounting requests
buffered in the router by RADIUS scheme, session ID, or time range. The displayed packet information can
help you troubleshoot RADIUS faults.
Any view
plc-mode
Use the plc-modecommand to configure packet loss compensation mode.
Voice Subscriber-Line view
policy vpn-target
Use the policy vpn-targetcommand to filter the received routing information according to the VPN-target
extended community attributes.
BGP-VPNv4 Subaddress Family view
port access vlan
port hybrid pvid vlan
port-mapping
Use the port access vlancommand to add the port whose link type is access to a specified VLAN.
Use the port hybrid pvid vlancommand to assign a default VLAN ID to the hybrid port.
Use the port-mappingcommand to establish a mapping from the port to application layer protocol.
Ethernet Port view
Ethernet Port view
System view
port trunk permit vlan
Use the port trunk permit vlancommand to assign the trunk port to the specified VLANs.
Ethernet Port view
Ethernet Interface view
System view
portal
Use the portalcommand to enable portal authentication on an interface.
portal all-resource-id
Use the portal all-resource-id command to configure the all-resource ID.
3Com Router 5000/6000 Family
Command Reference
113
portal auth-network
Use the portal auth-networkcommand to configure a network segment for portal authentication.
System view
System view
System view
System view
System view
System view
System view
System view
System view
System view
portal fast-authentication
Use the portal fast-authenticationcommand to enable fast portal authentication.
portal free-ip
portal free-user
portal method
Use the portal free-ipcommand to configure a free IP address.
Use the portal free-usercommand to configure a portal authentication-free user.
Use the portal methodcommand to specify a portal authentication method.
Use the portal resourcecommand to create an accessible-resource name.
Use the portal servercommand to configure a portal server or modify the configuration of a portal server.
Use the portal service-typecommand to set the portal authentication mode.
portal resource
portal server
portal service-type
portal update-resource
Use the portal update-resourcecommand to add an IP address to update resources.
portal update-resource-id
Use the portal update-resource-id command to configure the update-resource ID.
portal upload-ip
Use the portal upload-ipcommand to configure the IP address of the interface connected to the CAMS
server.
Ethernet Interface view
pos-server app tcp
pos-server app x25
Use the pos-server app tcpcommand to configure a POS application in TCP/IP connection mode.
System view
Use the pos-server app x25command to configure the specified POS application on the POSPAD client
router.
System view
System view
System view
System view
System view
System view
pos-server checkschar
pos-server enable
pos-server fcm
Use the pos-server checkscharcommand to enable the system to check POS packets for the string 10 04.
Use the pos-server enablecommand to enable POS access server.
Use the pos-server fcmcommand to configure FCM parameters for modem negotiation.
Use the pos-server mapcommand to configure a multi-application POS access map entry.
Use the pos-server padmodecommand to configure a POSPAD packet encapsulation format.
pos-server map
pos-server padmode
114
3Com Router 5000/6000 Family
Command Reference
pos-server source-ip
Use the pos-server source-ipcommand to bind the specified application with the source address of a
TCP connection.
System view
System view
pos-server wait-time
power-source
Use the pos-server wait-timecommand to set the POSPAD wait timer.
Use the power-sourcecommand to enable remote power supply.
BSV Interface view (in NT mode)
ppp authentication-mode
Use the ppp authentication-modecommand to set the mode that the local PPP uses to authenticate the
peer router.
Interface view
Virtual-Template Interface view
ppp callback
Use the ppp callbackcommand to enable an interface to send or accept PPP callback requests.
Physical or Dialer Interface view
ppp callback ntstring
Use the ppp callback ntstringcommand to configure the dial number required for a Windows NT server
to call back the router.
Physical or Dialer Interface view
ppp chap password
ppp chap user
Use the ppp chap passwordcommand to configure the password for CHAP authentication.
Use the ppp chap usercommand to configure the user name when performing the CHAP authentication.
Use the ppp compression iphccommand to enable IP header compression on the interface.
Interface view
Interface view
Interface view
ppp compression iphc
ppp compression iphc rtp-connections
Use the ppp compression iphc rtp-connectionscommand to designate the connections number of IP
Header Compression allowed on one interface.
Interface view
ppp compression iphc tcp-connections
Use the ppp compression iphc tcp-connectionscommand to configure the connection number of TCP
compression mode.
Interface view
Interface view
Interface view
ppp compression stac-lzs
Use the ppp compression stac-lzscommand to enable STAC-LZS compression for PPP.
Use the ppp ipcp dnscommand to enable the router to allocate a DNS address to the peer.
ppp ipcp dns
ppp ipcp dns admit-any
Use the ppp ipcp dns admit-anycommand to enable the router to accept the unsolicited DNS server
address allocated by the peer without sending a DNS request.
Interface view
Interface view
Interface view
ppp ipcp dns request
Use the ppp ipcp dns requestcommand to enable the router to request the peer for a DNS server
address.
ppp ipcp remote-address forced
Use the ppp ipcp remote-address forcedcommand to forbid the peer to use the fix self-configured IP
address but the one allocated by this router.
3Com Router 5000/6000 Family
Command Reference
115
ppp lcp mru consistent
Use the ppp lcp mru consistentcommand to enable PPP LCP to negotiation maximum receive unit
(MRU).
Interface view
Interface view
ppp lqc
Use the ppp lqccommand to enable PPP link quality control (LQC).
Use the ppp mpcommand to enable the interface encapsulated with PPP to operate in the MP mode.
Use the ppp mp binding-modecommand to set the MP binding condition.
ppp mp
Interface view
ppp mp binding-mode
Dialer Interface view
Virtual Template Interface view,
ppp mp lfi
ppp mp lfi
Use the ppp mp lficommand to configure the link fragmentation and interleaving features.
Virtual Template Interface view
Use the ppp mp lficommand to enable link fragmentation and interleaving (LFI) on the interface.
MP-Group Interface view
Virtual Template Interface view,
ppp mp lfi delay-per-frag
Use the ppp mp lfi delay-per-fragcommand to set the maximum time delay for transmitting a LFI
fragment.
MP-Group Interface view
Virtual Template Interface view,
ppp mp max-bind
ppp mp min-bind
Use the ppp mp max-bindcommand to configure maximum number of bound links of MP.
Dialer Interface view
Virtual Template Interface view
Use the ppp mp min-bindcommand to configure the minimum number of PPP links that an MP bundle must
have.
Dialer Interface view
ppp mp min-fragment
ppp mp mp-group
Use the ppp mp min-fragmentcommand to set minimum size of outgoing fragments.
Virtual Template Interface view
Interface view
Use the ppp mp mp-groupcommand to add the current interface to the specified MP-group.
ppp mp sort-buffer-size
Use the ppp mp sort-buffer-sizecommand to set the size of the MP sort window.
MP-Group Interface view
Virtual Template Interface view
ppp mp user
Use the ppp mp usercommand to bind an MP user to a virtual template.
System view
ppp mp virtual-template
Use the ppp mp virtual-templatecommand to configure the virtual template number to be bound by the
interface.
Interface view
ppp pap local-user
ppp timer negotiate
Use the ppp pap local-usercommand to configure the username and password sent by the local router
when it is authenticated by the peer router via the PAP method.
Interface view
Interface view
Use the ppp timer negotiatecommand to set the PPP negotiation timeout.
116
3Com Router 5000/6000 Family
Command Reference
pppoe-client
Use the pppoe-clientcommand to establish a PPPoE session and specify the Dialer Bundle
corresponding to the session.
Ethernet Interface (subinterface) view
Virtual Ethernet Interface view
pppoe-server bind virtual-template
Use the pppoe-server bind virtual-templatecommand to enable PPPoE on the virtual-template
specified by the Ethernet interface.
Interface view
System view
System view
System view
System view
pppoe-server log-information off
Use the pppoe-server log-information offcommand to enable the PPPoE server to output the
PPP-related log information.
pppoe-server max-sessions local-mac
Use the pppoe-server max-sessions local-maccommand to set the maximum number of PPPoE
sessions that can be established at a local MAC address.
pppoe-server max-sessions remote-mac
Use the pppoe-server max-sessions remote-maccommand to set the maximum number of PPPoE
sessions that can be established at a peer MAC address.
pppoe-server max-sessions total
Use the pppoe-server max-sessions totalcommand to set the maximum number of PPPoE sessions
that the system can establish.
pq
Use the pqcommand to set the queue type of frame relay virtual circuit as Priority Queuing.
Frame Relay Class view
pre-shared-key
Use the pre-shared-keycommand to set the pre-shared key used when a client needs to authenticate a
DVPN server.
Dvpn-Class view
IKE-Peer view
pre-shared-key
preference
Use the pre-shared-keycommand to configure a pre-shared key to be used in IKE negotiation.
Use the preferencecommand to configure the preference of BGP protocol.
BGP Protocol view
BGP Multicast Address Family view
preference
preference
preference
preference clns
pri-set
Use the preferencecommand to configure the preference of IS-IS protocol.
Use the preferencecommand to configure the preference of an OSPF protocol route.
Use the preferencecommand to configure the route preference of RIP.
IS-IS view
OSPF view
RIP view
Use the preference clnscommand to set the preference of the CLNS routes discovered by IS-IS protocol.
Use the pri-setcommand to bundle timeslots on the CT1/PRI or CE1/PRI interface into a pri-set.
IS-IS view
CE1/PRI Interface view
CT1/PRI Interface view
pri-set (CE1/PRI Interface)
Use the pri-setcommand to have timeslots on the CE1/PRI interface form a pri-set.
CE1/PRI Interface view
3Com Router 5000/6000 Family
Command Reference
117
pri-set (CT1/PRI Interface)
Use the pri-setcommand to bundle the timeslots of the CT1/PRI interface into a pri-set.
CT1/PRI Interface view
primary accounting
primary accounting
Use the primary accountingcommand to configure IP address and port number of the primary RADIUS
accounting server.
RADIUS view
Use the primary accounting command to configure a primary TACACS accounting server.
TACACS+ view
primary authentication
Use the primary authenticationcommand to configure IP address and port number of the primary
RADIUS authentication/authorization server.
RADIUS view
TACACS+ view
TACACS+ view
Voice Entity view
Dvpn-Class view
primary authentication
Use the primary authenticationcommand to configure a primary TACACS authentication server.
Use the primary authorizationcommand to configure a primary TACACS authorization server.
Use the prioritycommand to configure the priority levels for voice entities.
primary authorization
priority
private-ip
Use the private-ip command to specify a private IP address of a specified DVPN server.
private-line
Use the private-linecommand to configure private auto-ring mode for the subscriber line and the E.164
telephone number of the destination end.
Voice Subscriber-Line view
probe-failtimes
Use the probe-failtimescommand to configure the number of consecutive probe failures allowed in an
HWPing test before a trap is sent to the NMS.
HWPing Test Group view
process-config
promiscuous
proposal
Use the process-configcommand to configure the dialing process of a certain access service number.
Voice Access-Number view
Use the promiscuouscommand to set the Ethernet interface to operate in promiscuous mode.
Use the proposal command to set the proposal used by the IPSec policy.
Ethernet Interface view
IPSec Policy view
IPSec Policy Template view
protocol inbound
Use the protocol inboundcommand to enable the current user interface to support Telnet, PAD, SSH, or
all of them.
VTY Interface view
System view
protocol-priority
Use the protocol-prioritycommand to set a priority for a protocol globally.
proxy
Use the proxycommand to configure the IPv4 address and port number of the proxy server.
Use the public-ip command to specify a public IP address of a specified DVPN server.
SIP Client view
Dvpn-Class view
public-ip
118
3Com Router 5000/6000 Family
Command Reference
public-key-code begin
Use the public-key-code begincommand to enter public key code view.
Public Key view
public-key-code end
Use the public-key-code endcommand to return from public key code view to public key view and to save
the configured public key.
Public Key Code view
put
put
pvc
Use the putcommand to FTP a local file to the remote FTP server.
FTP Client view
Use the putcommand to upload a local file to the remote SFTP server.
SFTP Client view
Use the pvccommand to create a PVC or enter the PVC view at ATM interface or in PVC-Group view.
ATM Interface view
PVC-Group view
pvc-group
pvc max-number
pvc-pq
Use the pvc-groupcommand to create a PVC-Group or enter the PVC-Group view at ATM interface.
Use the pvc max-numbercommand to set the maximum number of ATM interface virtual circuits (VC).
ATM Interface view
ATM Master Interface view
Use the pvc-pqcommand to set the type of the PVC PQ that packets sent by frame relay virtual circuit enter.
Frame Relay Class view
ATM Pvc-Group view
Interface view
pvc-protect
pvp create
pvp limit
pwd
Use the pvc-protectcommand to configure the protection mode for a PVC in a PVC group.
Use the pvp createcommand to create a virtual path.
Use the pvp limitcommand to set the parameters for VP policing.
Use the pwdcommand to view the working directory on the remote FTP server.
Use the pwdcommand to display the current directory on the SFTP server.
Use the pwdcommand, you can view the current path.
ATM Master Interface view
FTP Client view
pwd
SFTP Client view
User view
pwd
qmtoken
queue af
Use the qmtokencommand to configure the number of transmitted tokens.
Interface view
Use the queue afcommand to configure the class to perform the assured-forwarding and the minimum
bandwidth used.
Traffic Behavior view
queue ef
Use the queue efcommand to configure expedited-forwarding packets to the absolute priority queue and
configure the maximum bandwidth.
Traffic Behavior view
queue-length
Use the queue-lengthcommand to configure maximum queue length.
Traffic Behavior view
3Com Router 5000/6000 Family
Command Reference
119
queue wfq
Use the queue wfqcommand to configure the default-class to use WFQ.
Traffic Behavior view
quit
Use the quitcommand to return from current view to lower level view, or exit the system if current view is
user view.
Any view
quit
quit
Use the quitcommand to disconnect from the remote FTP server and exit to user view.
FTP Client view
Use the quitcommand to terminate the connection to the remote SFTP server and exit to system view as
you would with the byeand exitcommands.
SFTP Client view
User view
quit
Use the quitcommand to terminate the connection to the remote SSH server.
Use the qos apply policycommand to apply a service policy to the interface.
Use the qos carcommand to implement TP policy on an interface.
Use the qos carlcommand to establish or modify a CARL.
qos apply policy
Interface view
Interface view
System view
Interface view
qos car
qos carl
qos cq
Use the qos cq cqlcommand to apply the customized queue to an interface.
qos cql default-queue
Use the qos cql default-queuecommand to assign a default queue for those packets that do not match
any rule in the CQL.
System view
System view
System view
qos cql inbound-interface
Use the qos cql inbound-interfacecommand to establish classification rules based on interfaces.
qos cql protocol
Use the qos cql protocolcommand to establish classification rules based on the protocol type.
qos cql protocol mpls exp
Use the qos cql protocol mpls exp command to configure classification rule based on the MPLS
protocol.
System view
System view
qos cql queue
Use the qos cql queuecommand to configure the length of a queue, namely, the number of packets a
queue can hold.
qos cql queue serving
Use the qos cql queue servingcommand to set the byte-count of the packets sent from a given queue in
each poll.
System view
Interface view
qos fifo queue-length
Use the qos fifo queue-lengthcommand to set the length limit of FIFO queue.
qos gts
Use the qos gtscommand to set shaping parameters for all or a specified type of traffic and perform traffic
shaping.
Interface view
120
3Com Router 5000/6000 Family
Command Reference
qos lr
Use the qos lrcommand to limit the transmitting rate of the interface.
Interface (including the MFR Interface) view
qos max-bandwidth
Use the qos max-bandwidthcommand to configure the maximum interface bandwidth used when CBQ
enqueues packets.
Interface view
System view
Interface view
qos policy
Use the qos policycommand to define a policy and enter policy view.
Use the qos pqcommand to apply a group of priority list to an interface.
qos pq
qos pql default-queue
Use the qos pql default-queuecommand to designate the packets without corresponding rules to a
default queue.
System view
System view
System view
qos pql inbound-interface
Use the qos pql inbound-interfacecommand to establish classification rules based on interfaces.
qos pql protocol
qos pql queue
Use the qos pql inbound-interfacecommand to establish classification rules based on interfaces.
Use the qos pql queuecommand to specify the maximum number of packets that can wait in each of the
priority queues, or the length of a PQ.
System view
System view
Interface view
qos pql protocol mpls exp
Use the qos pql protocol mpls expcommand to establish the classification rule based on MPLS protocol.
qos reserved-bandwidth
Use the qos reserved-bandwidthcommand to set the maximum reserved bandwidth percentage.
qos rtpq
Use the qos rtpqcommand to enable RTP queue feature on an interface so as to reserve a real-time
service for the RTP packets sent to some UDP destination port ranges.
Interface view
qos wfq
Use the qos wfq command to apply WFQ to and configure WFQ parameters on the interface or modify
WFQ parameters on the interface.
Interface view
Interface view
qos wred
Use the qos wredcommand to apply WRED at an interface.
qos wred dscp
Use the qos wred dscp command to set the lower limit, upper limit, and drop probability denominator of a
WRED DSCP.
Interface view
Interface view
qos wred ip-precedence
Use the qos wred ip-precedencecommand to configure the minimum threshold, maximum threshold and
drop probability denominator for each precedence level in WRED.
qos wred weighting-constant
Use the qos wred weighting-constantcommand to set exponential used to calculate the average length
of WRED queues.
Interface view
System view
radius nas-ip
Use the radius nas-ipcommand to specify the source address of the RADIUS packet sent from NAS.
3Com Router 5000/6000 Family
Command Reference
121
radius scheme
Use the radius schemecommand to configure a RADIUS scheme and enter its view.
System view
System view
radius trap
ras-on
Use the radius trapcommand to enable the RADIUS server to send traps when it goes down.
Use the ras-oncommand to enable the GK Client function.
Voice GK Client view
R2 CAS view
re-answer
Use the re-answercommand to enable or disable the originating point to support re-answer signal process.
Use the re-authenticationcommand to enable console login re-authentication.
Use the rebootcommand to have the router reboot.
re-authentication
User Interface view
User view
reboot
receive gain
redialtimes
Use the receive gaincommand to configure the gain value at the voice subscriber-line input end.
Voice Subscriber-Line view
Use the redialtimescommand to configure the number of times of dialing in each dialing phase for a
certain access service number.
Voice Access-Number view
redirect bind vpn-instance
Use the redirect bind vpn-instancecommand to bind a VPN instance to the user interface.
User Interface view
redirect disconnect
redirect enable
Use the redirect disconnectcommand to disconnect a redirected telnet connection manually.
Use the redirect enablecommand to enable redirect on the asynchronous serial interface.
User Interface view
User Interface view
redirect listen-port
Use the redirect listen-portcommand to specify a port to listen for redirected Telnet connections.
User Interface view
User Interface view
User Interface view
redirect refuse-negotiation
Use the redirect refuse-negotiationcommand to disable Telnet option negotiation during setup of
redirected Telnet connection.
redirect return-deal from-telnet
Use the redirect return-deal from-telnetcommand to have the router that redirects Telnet connection
substitute 0x0d for 0x0d 0x0a and 0x0d 0x00, the carriage returns received from the Telnet client.
redirect return-deal from-terminal
Use the redirect return-deal from-terminalcommand to have the router that redirects Telnet
connection substitute 0x0d for 0x0d 0x0a and 0x0d 0x00, the carriage returns received from the terminal (a
PC connected to the console port for example).
User Interface view
User Interface view
redirect timeout
Use the redirect timeoutcommand to specify the amount of time that a redirected Telnet connection can
stay idle. After that, the connection is disconnected.
reflect between-clients
Use the reflect between-clientscommand to enable route reflection between clients.
BGP view
VPNv4 view
VPN Instance view
122
3Com Router 5000/6000 Family
Command Reference
reflector cluster-id
Use the reflector cluster-idcommand to configure the cluster ID of the route reflector.
BGP Unicast view
BGP Multicast view
VPNv4 view
refresh bgp
Use the refresh bgp command to request the peer to retransmit routes or retransmit routes to the peer.
Use the register-enablecommand to enable or disable the SIP registration function.
Use the register lifetimecommand to configure the registration lifetime of an MR.
User view
SIP Client view
MR view
register-enable
register lifetime
register-number
Use the register-numbercommand to enable the gateway (the VoIP-enabled router) to register the
number of the voice entity with the H.323 gatekeeper or SIP server.
Voice Entity view
PIM view
register-policy
Use the register-policycommand to configure a RP to filter the register packet sent by the DR in the
PIM-SM network and to accept the specific packet only.
register retransmit
Use the register retransmitcommand to configure the registration retransmission parameters of an MR,
including the initial registration retransmission interval, the maximum registration retransmission interval,
and the maximum number of registration retransmission attempts.
MR view
register-value
registrar
Use the register-valuecommand to configure the value of all register signals of R2 signaling.
R2 CAS view
Use the registrarcommand to configure the IP address or domain name, port number, timeout time as
well as master/slave attribute of the registration server under UAs.
SIP Client view
Traffic Behavior view
Traffic Behavior view
Traffic Behavior view
Traffic Behavior view
Traffic Behavior view
Traffic Behavior view
IKE-Peer view
remark atmclp
remark dot1p
Use the remark atmclpcommand to have the system remark the CLP bit of ATM packets in the class.
Use the remark dot1pcommand to configure the 802.1p priority value in the VLAN packets of a class.
Use the remark dscpcommand to set a remarked DSCP value for IP packets belonging to the class.
Use the remark fr-decommand to set the remarked DE bit of frame relay packets.
Use the remark ip-precedencecommand to configure IP precedence remark.
remark dsc
remark fr-de
remark ip-precedence
remark mpls-exp
remote-address
remote address
Use the remark mpls-expcommand to configure MPLS EXP value to identify matched packets.
Use the remote-addresscommand to configure IP address of the remote GW.
Use the remote addresscommand to configure to assign IP address for the peer interface.
Interface view
3Com Router 5000/6000 Family
Command Reference
123
remote-ip
Use the remote-ipcommand to configure a remote IP address. The address should be the LSR ID of the
remote LSR. As remote peers adopt LSR ID as their transport addresses, the last two remote peers use
their LSR ID as their transport addresses for creating TCP connection.
Remote-Peer view
IKE-Peer view
remote-name
remotehelp
remove
Use the remote-namecommand to specify a name for the remote GW.
Use the remotehelpcommand to view the help for the FTP commands.
FTP Client view
Use the removecommand to delete the specified file from the server as you would with the delete
command.
SFTP Client view
remove slot
Use the remove slotcommand to have the system do some pre-processing work before removing an
interface card.
User view
FTP Client view
SFTP Client view
User view
rename
Use the renamecommand to rename a file on the FTP server from the FTP client.
Use the renamecommand to change the name of the specified file on the SFTP server.
Use the renamecommand to rename a file.
rename
rename
renew
Use the renewcommand to configure the signal values of C bit and D bit.
Use the resetcommand to reset the system parameters of RIP.
R2 CAS view
RIP view
reset
reset acl counter
reset alarm urgent
reset l2tp session
Use the reset acl countercommand to clear the statistics of access control list
Use the reset alarm urgentwcommand to clear all the stored alarms.
User View
User view
Use the reset l2tp session command to disconnect a session. When the user calls in, the session can
be set up again.
User view
reset l2tp tunnel
Use the reset l2tp tunnelcommand to clear the specified tunnel connection and all sessions on the
tunnel.
User view
User view
User view
reset l2tp user
reset arp
Use the reset l2tp usercommand to disconnect the L2TP connection of the specified user.
Use the reset arpcommand to clear the ARP entries in the ARP mapping table.
reset atm
Use the reset atmcommand to clear statistics about all PVCs on the specified ATM interface, excluding
statistics about the ATM interface.
User view
124
3Com Router 5000/6000 Family
Command Reference
reset bgp
Use the reset bgppeer-addresscommand to reset the connection of BGP with a specified peer.
User view
User view
reset bgp flap-info
reset bgp group
Use the reset bgp flap-infocommand to reset the flap statistics of routes.
Use the reset bgp groupcommand to reset the BGP connections of all the members in the specified peer
group.
User view
reset bridge address-table
Use the reset bridgecommand to clear all the dynamic address entries or the entries of a specified bridge
set or a specified interface in the forwarding table.
User view
User view
User view
User view
User view
User view
User view
reset bridge traffic
reset clns statistics
Use the reset bridge trafficcommand to clear the traffic statistics of a bridge set on a interface.
Use the reset clns statisticscommand to reset statistics information about CLNS flow.
reset counters controller e1
Use the reset counters controller e1command to clear the controller counter for the CE1/PRI interface.
reset counters controller t1
Use the reset counters controller t1command to clear the controller counter for the CT1/PRI interface.
reset counters encrypt
Use the reset counters interface encryptcommand to clear the statistics on the encryption card.
reset counters interface
Use the reset counters interfacecommand to reset the statistics about the port.
reset counters interface
Use the reset counters interfacecommand to clear statistics about the transmitted and received
packets, IP, ARP, and ICMP on the specified interface or all interfaces.
User view
User view
reset dampening
Use the reset dampeningcommand to clear the dampening information and flap statistics of a route and
release the suppression of a suppressed route.
reset dhcp ip-in-use
Use the reset dhcp server ip-in-usecommand to clear the DHCP dynamic address binding information,
outdated or not.
User view
User view
User view
reset dhcp relay statistics
Use the reset dhcp relay statisticscommand to clear the DHCP relay statistics.
reset dhcp server conflict
Use the reset dhcp server conflictcommand to clear the statistics about DHCP address collision.
reset dhcp server statistics
Use the reset dhcp server statisticscommand to clear the statistics on the DHCP server, including
such information as number of DHCP address pools, automatically and manually bound addresses and
expired addresses, number of unknown packets, number of DHCP request packets, and number of
response packets.
User view
3Com Router 5000/6000 Family
Command Reference
125
reset dlsw bridge-entry
Use the reset dlsw bridge-entrycommand to clear the entry cache information in the DLSw bridge
group.
User view
User view
reset dlsw circuits
Use the reset dlsw circuitscommand to clear the DLSw virtual circuit information.
reset dlsw ethernet-backup circuit
Use the reset dlsw ethernet-backup circuitcommand to clear information about all circuits that the
router and its neighbors have established with the remote peers since DLSw Ethernet redundancy is
enabled.
User view
User view
User view
reset dlsw ethernet-backup map
Use the reset dlsw ethernet-backup mapcommand to clear the MAC address map of the Ethernet switch
support feature.
reset dlsw reachable-cache
Use the reset dlsw reachable-cachecommand to clear information from the reachable-cache of the
DLSw.
reset dlsw tcp
Use the reset dlsw tcpcommand to reestablish or delete all connection to all the remote peers.
Use the reset dlsw tcp ip-address command to reestablish a TCP connection or delete the connection
to the specified remote peer.
User view
User view
reset dns dynamic-host
Use the reset dns dynamic-hostcommand to clear the current contents in the domain name cache of the
DNS client.
reset dvpn all
Use the reset dvpn all command to clear all operating information about a specified DVPN domain and
to initiate the DVPN domain.
User view
User view
User view
User view
User view
reset dvpn map
Use the reset dvpn mapcommand to clear a specified map.
reset dvpn session
reset dvpn statistics
reset encrypt-card sa
Use the reset dvpn sessioncommand to clear a specified session.
Use the reset dvpn statisticscommand to clear all the statistics information of a DVPN module.
Use the reset encrypt-card sacommand to clear the SAs on the encryption card.
reset encrypt-card statistics
Use the reset encrypt-card statisticscommand to clear the statistics during processing of the
encryption card.
User view
User view
User view
reset encrypt-card syslog
Use the reset encrypt-card syslogcommand to clear all the logging information on the encryption card.
Use the reset esis statisticscommand to reset statistics information about ES-IS flow.
reset esis statistics
reset fcm
Use the reset fcmcommand to clear the dial-up negotiation failure counter and the timeout disconnection
counter for each FCM interface.
User view
126
3Com Router 5000/6000 Family
Command Reference
reset firewall ethernet-frame-filter
reset firewall-statistics
Use the reset firewall ethernet-frame-filtercommand to clear the ACL-based firewall statistics.
User view
User view
User view
Use the reset firewall-statisticscommand to clear the firewall statistics.
reset fr inarp
Use the reset fr inarpcommand to clear the address mapping established by inverse ARP.
reset hwatacs statistics
Use the reset hwtacacs statisticscommand to clear TACACS+ protocol statistics.reset hwtacacs
statistics
User view
reset igmp group
Use the reset igmp groupcommand to delete the IGMP group joined on the interface. The deletion of the
group does not affect its joining again.
User view
User view
User view
User view
reset ike sa
Use the reset ike sacommand to delete the security tunnel set up by IKE.
reset ip count
Use the reset ip countcommand to clear information that the IP Accounting retained about IP packets.
reset ip fast-forwarding cache
Use the reset ip fast-forwarding cachecommand to reset the unicast fast forwarding cache.
reset ip multicast-fast-forwarding cache
Use the reset ip multicast-fast-forwarding cachecommand to clear the multicast fast forwarding
cache. However, this command does not release the space occupied by the cache.
User view
reset ip netstream statistics
Use the reset ip netstream statisticscommand to age and export all stream statistics to clear the
NetStream cache.
User view
User view
reset ip routing-table
Use the reset ip routing-tablecommand to clear the routing table.
reset ip statistics
Use the reset ip statisticscommand to clear the IP statistics information. In some special cases, it is
necessary to clear the IP statistics information and perform new statistics.
User view
User view
User view
reset ipsec sa
Use the reset ipsec sacommand to delete an SA already set up (manually or through IKE negotiation).
If no parameter (remote, policy, parameters) is specified, all the SA will be deleted.
reset ipsec statistics
Use the reset ipsec statisticscommand to clear IPSec message statistics, and set all the statistics to
zero.
reset ipx routing-table statistics
The reset ipx routing-table statisticscommand is used to clear the statistical information of a
specified type of IPX route.
User view
User view
User view
reset ipx statistics
reset isis all
Use the reset ipx statisticscommand to clear IPX statistics by the system.
Use the reset isis allcommand to reset all the IS-IS data.
3Com Router 5000/6000 Family
Command Reference
127
reset isis peer
Use the reset isis peercommand to reset the IS-IS data of specified IS-IS neighbor.
User view
reset lapb
Use the reset lapb statisticscommand to clear the statistics about LAPB.
Interface view
reset loadsharing
Use the reset loadsharing command to reset statistics about unbalanced load sharing for all interfaces
or the interfaces related to the equal-cost routes to the specified destination network.
User view
User view
reset logbuffer
Use the reset logbuffercommand to clear information in the log buffer.
reset mobile-ip binding
Use the reset mobile-ip bindingcommand to remove mobility bindings. With neither the ip-address
argument nor the interface-number argument specified, all mobility bindings are removed.
User view
reset mobile-ip mobile-router
Use the reset mobile-ip mobile-router agentcommand to clear agent information discovered by the
MR, MR registration information, and MR statistics.
User view
User view
User view
reset mobile-ip node-statistics
Use the reset mobile-ip node-statisticscommand to clear MN statistics.
reset mobile-ip statistics
Use the reset mobile-ip statisticscommand to clear all MIP counters.
reset mobile-ip visitor
Use the reset mobile-ip visitorcommand to delete information in the visitor table and the pending table
on the FA, or with the pending keyword specified to delete information in the pending table only. You can
also restrict deletion to one MN or MNs registered on an interface by specifying arguments ip-address
and interface ethernet interface-numberrespectively.
User view
reset mpls cell-transfer interface
Use the reset mpls cell-transfer interfacecommand to reset statistics for the cells received/sent in
a packet on an interface in transparent transmission mode.
Any view
User view
reset mpls statistics
Use the reset mpls statisticscommand to clear MPLS statistics.
reset msdp peer
Use the reset msdp peercommand to reset TCP connection with the specified MSDP peer, and clear all
the statistics of the specified MSDP peer.
User view
User view
reset msdp sa-cache
Use the reset msdp sa-cachecommand to clear SMDP SA cache entries.
reset msdp statistics
Use the reset msdp statisticscommand to clear statistics of one or more MSDP peers without resetting
the MSDP peer.
User view
User view
User view
reset multicast forwarding-table
Use the reset multicast forwarding-tablecommand to clear MFC forwarding entries or the statistics
of MFC forwarding entries.
reset multicast routing-table
Use the reset multicast routing-tablecommand to clear the route entry in the multicast kernel routing
table and remove the corresponding forwarding entry in MFC.
128
3Com Router 5000/6000 Family
Command Reference
reset nat
Use the reset natcommand to clear up the mapping tables of address translation in the memory and
release all the memory dynamically allocated to store the mapping tables.
User view
reset ospf
Use the reset ospf allcommand to reset all the OSPF processes. Use the parameter of statistics to reset
statistics about OSPF.
Use the reset ospfcommand to reset the OSPF process, the following results are expected:
User view
User view
User view
User view
reset pim neighbor
Use the reset pim neighborcommand to clear PIM neighbor.
reset pim routing-table
Use the reset pim routing-tablecommand to clear PIM route entry.
reset portal
reset pos
Use the reset portalcommand to clear the related portal statistics.
Use the reset poscommand to clear the counters for POS applications and POS access ports, that is, the
information displayed with the display pos-appand display pos-interfacecommands.
User view
reset ppp compression iphc
Use the reset ppp compression iphccommand to delete the invalid IP/UDP/RTP header compression or
decompression context storage table and clear statistic information of IP/UDP/RTP header compression.
User view
User view
User view
User view
reset ppp compression stac-lzs
Use the reset ppp compression stac-lzscommand to clear statistics about STAC-LZS compression.
Use the reset pppoe-clientcommand to terminate PPPoE session and re-initiate the connection later.
Use the reset pppoe-servercommand to clear PPPoE sessions at the server end.
reset pppoe-client
reset pppoe-server
reset radius statistics
Use the reset radius statisticscommand to clear the statistic information related to the RADIUS
protocol.
User view
User view
reset recycle-bin
Use the reset recycle-bincommand to delete one or files from the recycle bin completely.
reset saved-configuration
Use the reset saved-configurationcommand to delete the configuration file loaded at this startup from
the Flash.
User view
reset stop-accounting-buffer
Use the reset stop-accounting-buffercommand to clear the buffered stop-accounting requests that
have no responses.
System view
reset stop-accounting-buffer
Use the reset stop-accounting-buffercommand to clear the stop-accounting requests that have no
response and are buffered on the router.
User view
User view
reset stp statistics
Use the reset stp statisticscommand to clear statistics about the spanning tree.
3Com Router 5000/6000 Family
Command Reference
129
reset tcp statistics
Use the reset tcp statisticscommand to clear TCP traffic statistic information. After the execution of
this command, there’s no prompt information on the screen, and the existing statistics are cleared.
User view
User view
reset trapbuffer
Use the reset trapbuffercommand to clear information in the trap buffer.
reset udp statistics
Use the reset udp statistics command to clear the UDP statistics information. After the execution of
this command, there’s no prompt information on the screen, and the existing statistics are cleared.
User view
User view
reset vlan statistics vid
Use the reset vlan statistics vidcommand to clear the VLAN statistics.
reset voice call-history-record line
Use the reset voice call-history-record linecommand to clear the call history of all voice subscriber
lines, or information displayed by the display voice call-history-record linecommand.
Use the reset voice emcommand to reset the call statistics on the digital E&M interface.
Use the reset voice faxcommand to reset fax statistics.
User view
User view
User view
reset voice em
reset voice fax
reset voice fax trans-statistics
Use the reset voice fax trans-statistics command to reset the statistics for the FAX transform
module.
User view
User view
User view
User view
User view
User view
User view
User view
User view
User view
reset voice ipp
reset voice r2
reset voice rcv
reset voice sip
reset voice vcc
Use the reset voice ippcommand to reset IPP statistics.
Use the reset voice r2command to reset the call statistics of R2 signaling.
Use the reset voice rcvcommand to reset RCV statistics.
Use the reset voice sipcommand to reset all the statistic information about the SIP client.
Use the reset voice vcccommand to reset the information related to VCC.
reset voice voip data-statistics
Use the reset voice voip data-statisticcommand to reset statistics information of voice data.
reset voice vpp
Use the reset voice vppcommand to reset VPP statistics.
reset web java-blocking counter
Use the reset web java-blocking countercommand to clear the Java blocking statistics information.
reset web log-buf
Use the reset web log-bufcommand to clear the web filtering log buffer.
reset web url-filter host counter
Use the reset web url-filter host countercommand to clear the URL address filtering statistics
information.
User view
130
3Com Router 5000/6000 Family
Command Reference
reset web url-filter parameter counter
Use the reset web url-filter parameter countercommand to clear the statistics of SQL injection attack
protection.
User view
reset x25
reset xot
Use the reset x25command to reset statistics about X.25 on the specified interface or to reset the specified
X.25 VC.
User view
For SVC, use the reset xotcommand to initiatively clear an XOT link.
For PVC, use the reset xotcommand to initiatively reset an XOT link.
User view
Interface view
restart
retry
Use the restartcommand to reset the physical interface.
Use the retrycommand to set the maximum number of probing retries during an auto detect interval.
Use the retrycommand to configure the number of RADIUS request attempts.
Detect Group view
RADIUS view
retry
retry realtime-accounting
Use the retry realtime-accountingcommand to configure the maximum number of real-time accounting
request attempts allowed to have no responses.
RADIUS view
RADIUS view
TACACS+ view
retry stop-accounting
Use the retry stop-accountingcommand to configure the maximal retransmission times after
stop-accounting request.
retry stop-accounting
Use the retry stop-accountingcommand to enable stop-accounting packet retransmission and configure
the maximum number of stop-accounting request attempts.
return
Use the returncommand to return to user view from any other view.
All views except User view
R2 CAS view
reverse
Use the reversecommand to configure the inversion mode of line signals.
Use the reverse-rtscommand to reverse RTS signal.
reverse-rts
reverse-tunnel
ring-generate
Synchronous Serial Interface view
MR view
Use the reverse-tunnelcommand to enable the reverse tunneling function for an MR.
Use the ring-generatecommand to configure the gateway at the called side to give a ringback tone when
in quick start mode.
Voice Subscriber-Line view
rip
Use the ripcommand to enable the RIP and enter the RIP view.
System view
rip authentication-mode
Use the rip authentication-modecommand to configure RIP-2 authentication mode and corresponding
parameters.
Interface view
Interface view
rip input
Use the rip inputcommand to allow an interface to receive RIP packets.
3Com Router 5000/6000 Family
Command Reference
131
rip metricin
Use the rip metricincommand to configure the additional route metric added to the route when an
interface receives RIP packets.
Interface view
rip metricout
Use the rip metricoutvaluecommand to enable RIP to send routes out the interface with an additional
route metric added. This command applies to routes both locally learned and learned from other routers.
Use the rip metricoutvalueall-routecommand to enable RIP to send routes out the interface with an
additional route metric added. This command applies to locally redistributed routes in addition to those
locally learned and learned from other routers.
Interface view
Interface view
rip output
Use the rip outputcommand to configure an interface to transmit RIP packets to the external.
rip split-horizon
Use the rip split-horizoncommand to configure an interface to use split horizon when transmitting RIP
packets.
Interface view
Interface view
Interface view
Interface view
User view
rip triggered
rip version
rip work
rlogin
Use the rip triggeredcommand to enable trigger RIP (TRIP).
Use the rip versioncommand to configure the version of RIP packets on an interface.
Use the rip workcommand to enable the running of RIP on an interface.
Use the rlogincommand to rlogin onto the specified remote host with the specified user name.
Use the rmdircommand to delete a specified directory from the FTP server.
Use the rmdircommand to delete the specified directory from the remote SFTP server.
Use the rmdircommand to delete a directory.
rmdir
FTP Client view
SFTP Client view
User view
rmdir
rmdir
rmon alarm
Use the rmon alarmcommand to set an alarm entry. When an exception occurs, the alarm is triggered. The
alarm in turn triggers the corresponding event, which can be log, trap, or log-and-trap.
System view
System view
rmon event
Use the rmon eventcommand to add an event entry.
rmon history
rmon prialarm
rmon statistics
Use the rmon historycommand to add a history control entry.
Ethernet Interface view
System view
Use the rmon prialarmcommand to add an entry to the prialarm table.
Use the rmon statisticscommand to add a statistics entry.
Ethernet Interface view
root-certificate fingerprint
Use the root-certificate fingerprintcommand to configure the fingerprint for authenticating the CA
root certificate.
PKI Domain view
132
3Com Router 5000/6000 Family
Command Reference
route-distinguisher
Use the route-distinguishercommand to configure RD for an MPLS VPN instance. A vpn-instance
cannot run until it is configured with an RD.
MBGP VPN-Instance view
route-policy
Use the route-policycommand to create a route-policy or a route-policy node and enter the corresponding
view.
System view
System view
route-policy
route-tag
Use the route-policycommand to configure a route-policy node and enter the route-policy view.
Use the route-tagcommand to specify a tag value to identify VPN import route.
OSPF Protocol view
routed-bridge protocol
Use the routed-bridge protocolcommand to enable the support of routed bridge encapsulation to a
network protocol.
ATM PVC view
System view
router id
Use the router idcommand to configure the ID of a router running the OSPF protocol.
routing-table limit
Use the routing-table limit command to limit the route maximum in a vpn-instance, to avoid too many
routes in the ingress interface of the PE router.
MBGP VPN-Instance view
System view
rsa local-key-pair create
Use the rsa local-key-pair createcommand to generate the local RSA host key pair and server key
pair.
rsa local-key-pair destroy
Use the rsa local-key-pair destroycommand to remove all RSA keys on the server (including the host
key pair and the server key pair).
System view
rsa peer-public-key
Use the rsa peer-public-keycommand to enter public key view. After that, you may use the
public-key-code begincommand and the public-key-code endcommand to configure the public key of
the client.
System view
User View
rsh
Use the rshcommand to execute a command on a remote host remotely.
rtpq
Use the rtpqcommand to configure to apply Realtime Transport Protocol (RTP) Priority Queuing.
Frame Relay Class view
ACL view
rule
Use the rulecommand to add a rule in current ACL view.
rule
Use the rulecommand to configure the number-substitute rules.
Voice Number-Substitute view
sa authentication-hex
Use the sa authentication-hexcommand to set the SA authentication key manually for the ipsec policy
of manual mode.
Manually-Established IPSec Policy view
sa duration
Use the sa durationcommand to specify the ISAKMP Sa duration for an IKE proposal.
IKE Proposal view
3Com Router 5000/6000 Family
Command Reference
133
sa duration
Use the sa durationcommand to set a SA duration of the ipsec policy.
IPSec Policy view
IPSec Policy Template view
sa encryption-hex
Use the sa encryption-hexcommand to set the SA encryption key manually for the ipsec policy of manual
mode.
Manually-Established IPSec Policy view
sa spi
Use the sa spicommand to set the SA SPI manually for the ipsec policy of manual mode.
Manually-Established IPSec Policy view
sa string-key
Use the sa string-keycommand to set the SA parameter manually for the ipsec policy of manual mode.
Manually-Established IPSec Policy view
save
Use the savecommand to save the current configuration file to the storage device.
Any view
schedule reboot at
Use the schedule reboot atcommand to enable the scheduled reboot function of the router and schedule
the reboot time and date.
User view
User view
schedule reboot delay
Use the schedule reboot delaycommand to enable scheduled router reboot and set the waiting time.
Use the schemecommand to configure the AAA scheme to be referenced by the current ISP domain.
scheme
ISP Domain view
scramble
Use the scramblecommand to enable an undo scrambleto scramble the payload on ATM OC-3c/STM-1
interface.
ATM Interface view
scramble
Use the scramblecommand to enable payload scrambling on the ATM E1/T1 interface. This, however,
does not affect cell headers.
ATM E1/T1 Interface view
ATM E3/T3 Interface view
POS Interface view
scramble
Use the scramblecommand to enable scrambling function of ATM E3/T3 interface.
Use the scramblecommand to enable the POS interface to scramble payload data.
Use the screen-lengthcommand to set the number of lines displayed on the terminal screen.
scramble
screen-length
screen-width
User Interface view
Use the screen-widthcommand to set the width of the terminal screen, that is, how many characters can
be displayed in one line.
User interface view
System view
script-string
Use the script-stringcommand to configure a Modem script.
script trigger connect
Use the script trigger connectcommand to configure the Modem script that will be executed once an
incoming call connection is established.
User Interface view
User Interface view
script trigger dial
Use the script trigger dialcommand to configure the Modem script that is used for DCC dialing.
134
3Com Router 5000/6000 Family
Command Reference
script trigger init
Use the script trigger initcommand to configure the Modem script that will be executed when the
system is powered on or rebooted.
User Interface view
User Interface view
User-interface view
script trigger login
Use the script trigger login command to configure the Modem script that will be executed when an
outgoing call connection is successfully established.
script trigger logout
Use the script trigger logoutcommand to configure the Modem script that is executed when a link is
reset.
sdlc controller
Use the sdlc controllercommand to configure the secondary station address of the SDLC.
Synchronous Serial Interface view
Synchronous Serial Interface view
Synchronous Serial Interface view
sdlc mac-map local
sdlc mac-map remote
sdlc max-pdu
Use the sdlc mac-map localcommand to configure the virtual MAC address of the SDLC.
Use the sdlc mac-map remotecommand to configure the SDLC peer.
Use the sdlc max-pducommand to configure the maximum receivable frame length of the SDLC.
Synchronous Serial Interface view
sdlc max-send-queue
sdlc max-transmission
sdlc modulo
Use the sdlc max-send-queuecommand to configure the queue length sending the SDLC packet.
Synchronous Serial Interface view
Use the sdlc max-transmissioncommand to configure the SDLC timeout retransmission times.
Synchronous Serial Interface view
Use the sdlc modulocommand to configure the modulus of the SDLC.
Synchronous Serial Interface view
sdlc sap-map local
Use the sdlc sap-map localcommand to configure the SAP address on transforming the SDLC into the
LLC2.
Synchronous Serial Interface view
sdlc sap-map remote
sdlc simultaneous
Use the sdlc sap-map remote command to configure the remote DLSw device SAP address when SDLC
is translated into LLC2.
Synchronous Serial Interface view
Use the sdlc simultaneouscommand to configure the SDLC data to use the bidirectional transmission
mode.
Synchronous Serial Interface view
sdlc status
Use the sdlc rolecommand to configure the SDLC role the device acts.
Synchronous Serial Interface view
sdlc timer ack
Use the sdlc timer ackcommand to configure the SDLC primary station response waiting time
(mseconds).
Synchronous Serial Interface view
sdlc timer lifetime
Use the sdlc timer lifetimecommand to configure the SDLC secondary station response waiting time
(mseconds).
Synchronous Serial Interface view
sdlc timer poll
Use the sdlc timer pollcommand to configure the SDLC poll pause timer.
Synchronous Serial Interface view
3Com Router 5000/6000 Family
Command Reference
135
sdlc window
Use the sdlc windowcommand to configure the length of the SDLC local response window.
Synchronous Serial Interface view
Synchronous Serial Interface view
sdlc xid
Use the sdlc xidcommand to configure the XID of the SDLC.
secondary accounting
Use the secondary accountingcommand to configure the IP address and port number for the secondary
RADIUS accounting server.
RADIUS view
secondary accounting
Use the secondary accountingcommand to configure a secondary TACACS accounting server.
TACACS+ view
secondary authentication
Use the secondary authenticationcommand to configure the IP address and port number of the
secondary RADIUS authentication/authorization/accounting server.
RADIUS view
TACACS+ view
TACACS+ view
secondary authentication
Use the secondary authenticationcommand to configure a secondary TACACS authentication server.
secondary authorization
Use the secondary authorizationcommand to configure a secondary TACACS authorization server.
security acl
Use the security aclcommand to set an access control list to be used by the ipsec policy and specify the
data stream protection mode.
IPSec Policy view
IPSec Policy Template view
security-policy-server
Use the security-policy-servercommand to specify the IP address of a security policy server.
RADIUS Scheme view
seizure-ack
select-mode
Use the seizure-ackcommand to enable or disable the terminating point to send seizure
acknowledgement signal.
R2 CAS view
R2 CAS view
Use the select-modecommand to configure the E1 trunk selection mode.
select-rule search-stop
Use the select-rule search-stopcommand to configure the maximum number of voice entities found.
Voice Dial Program view
Voice Dial Program view
Voice Dial Program view
Voice Entity view
select-rule type-first
Use the select-rule type-firstcommand to configure the type-first select rules for voice entities.
select-rule rule-order
Use the select-rule rule-ordercommand to configure the select rule of voice entities.
select-stop
Use the select-stopcommand to disable the search for voice entities.
send
Use the sendcommand to transfer messages between user interfaces.
Use the send allcommand to send messages to all user interfaces.
Use the sendnumbercommand to send messages to the user interface specified by its absolute index.
Use the sendtype-name numbercommand to send messages to the user interface specified by its
interface type and relative index.
User view
136
3Com Router 5000/6000 Family
Command Reference
send-busytone
Use the send-busytonecommand to enable busy tone sending on the FXO interface.
FXO Voice Subscriber-Line view
POTS Voice Entity view
send-number (in Voice Entity View)
Use the send-numbercommand to configure the number sending mode.
send-number (in Voice Subscriber-Line View)
Use the send-numbercommand to configure the FXS voice subscriber-line to allow the FXS to send called
numbers.
FXS Voice Subscriber-Line View
send-ring
Use the send-ringcommand to enable the local end to play ringback tone.
Use the send-trapcommand to configure the type of events that trigger trap sending.
Use the sendatcommand to manually send AT command to the modem.
VoIP Voice Entity view
send-trap
HWPing Test Group view
sendat
Interface (Asynchronous Serial Interface, AUX Port, or AM Interface) view
sendloopcode
sendpacket passroute
sendring
Use the sendloopcodecommand to send the remote loopback control code.
CT1/PRI Interface view
HWPing Test Group view
Use the sendpacket passroutecommand to enable routing table bypass.
Use the sendringcommand to enable or disable the terminating point to send ring-back tone or busy tone
signal to the calling party.
R2 CAS view
seq-number
Use the seq-numbercommand to enable voice packets transmitted on the local gateway to carry sequence
numbers.
Voice Entity view
RADIUS view
PVC view
server type
service cbr
service data
Use the server-typecommand to configure the RADIUS server type supported by the router.
Use the service cbrcommand to specify PVC service type as constant bit rate (CBR).
Use the service datacommand to enable data call service.
Voice Entity view
System view
service modem-callback
Use the service modem-callbackcommand to enable the callback function of modems.
service type
Use the service-typecommand to configure a service type for a particular user.
Local User view
Local User view
Local User view
service-type ftp
service-type ppp
service ubr
Use the service-type ftpcommand to specify a directory accessible for the FTP user.
Use the service-typecommand to configure the callback attribute and caller number of the PPP user.
Use the service ubrcommand to specify the service type of PVC as Unspecified Bit Rate (UBR) and
specify the related rate parameters.
PVC view
3Com Router 5000/6000 Family
Command Reference
137
service vbr-nrt
Use the service vbr-nrtcommand to specify the service type of PVC as Variable Bit Rate-Non Real Time
(VBR-NRT) and specify the related rate parameters.
PVC view
service vbr-rt
Use the service vbr-rt command to set the service type of PVC to Variable Bit Rate- Real Time (VBR-RT)
and specify the related rate parameters in the PVC view.
PVC view
session algorithm-suite
Use the session algorithm-suitecommand to specify the algorithm suite a session uses.
Dvpn-Policy view
session idle-time
Use the session idle-timecommand to set the L2TP session idle-timeout timer. Upon expiration of this
timer, the L2TP session is disconnected.
L2TP Group view
Dvpn-Policy view
Dvpn-Policy view
session idle-timeout
Use the session idle-timeoutcommand to set the idle timeout time for sessions.
session keepalive-interval
Use the session keepalive-intervalcommand to set the keepalive interval of sessions.
session setup-interval
Use the session setup-intervalcommand to set the interval for sending requests to establish a session
(Setup request). Setup request packets are sent regularly until the session is established.
Dvpn-Policy view
User Interface view
IS-IS view
set authentication password
Use the set authentication passwordcommand to set a local authentication password.
Use the set-overloadcommand to configure overload flag bit for the current router.
Use the sftpcommand to establish a connection to the remote SFTP server and enter SFTP client view.
Use the sftp server enablecommand to enable the secure FTP (SFTP) server.
set-overload
sftp
System view
sftp server enable
System view
sftp source-interface
Use the sftp source-interfacecommand to specify a source interface, which must be an existing local
interface, for the SFTP client. After that, the IP address of the specified interface is used as the source IP
address in each packet sent by the SFTP client.
System view
sftp source-ip
Use the sftp source-ipcommand to specify a source IP address for the packets sent by the SFTP client.
This IP address must be a local IP address.
System view
sham-link
shdsl mode
shdsl psd
Use the sham-linkcommand to configure a sham link.
OSPF Area view
Use the shdsl modecommand to set the operating mode of the G.SHDSL interface.
ATM (G.SHDSL) Interface view
Use the shdsl psdcommand to set PSD of the G.SHDSL interface working as CPE. It is not necessarily
the same as the one set at CO.
ATM (G.SHDSL) Interface view
138
3Com Router 5000/6000 Family
Command Reference
shdsl rate
Use the shdsl ratecommand to set single-pair interface rate of the SHDSL interface or just select
auto-negotiation mode. You can specify maximum line rate.
ATM (G.SHDSL) Interface view
ATM (G.SHDSL) Interface view
ATM (G. SHDSL) Interface view
User Interface view
shdsl snr-margin
shdsl wire
shell
Use the shdsl snr-margincommand to set a target margin to signal-to-noise ratio (SNR).
Use the shdsl wirecommand to set the operating mode of the current G.SHDSL interface.
Use the shellcommand to enable terminal services on the user interface.
Use the shell priority highcommand to set command execution first.
Use the shutdowncommand to shut down the CPOS physical interface.
Use the shutdowncommand to shut down the Ethernet port.
shell priority high
System view
shutdown
CPOS Interface view
Ethernet Port view
shutdown
shutdown
Use the shutdowncommand to disable the current switching PVC.
Use the shutdowncommand to shut down the interface.
Frame Relay Switching view
Interface view
shutdown
shutdown
Use the shutdowncommand to disable the MSDP peer specified.
MSDP view
shutdown (in Voice Entity View)
Use the shutdowncommand in voice entity view to configure to change the management status of specified
voice entity from UP to DOWN.
Voice Entity view
shutdown (in Voice Subscriber-Line View)
Use the shutdowncommand in voice subscriber-line view to configure the voice subscriber-line from UP to
DOWN.
Voice Subscriber-Line view
signal-value
Use the signal-value command to configure the digital E&M subscriber-line to receive and transmit the
ABCD bits of idle signaling and seizure signaling.
Digital E&M Voice Subscriber-Line view
silence-th-span
Use the silence-th-spancommand to set the silence detection parameters that have the system take
automatic on-hook action.
FXO Subscriber-Line view
silent-interface
silent interface
simultaneous-bindings
sip
Use the silent-interfacecommand to disable a specified interface to transmit IS-IS packet.
Use the silent-interfacecommand to disable an interface to transmit OSPF packet.
Use the simultaneous-bindingscommand to enable simultaneous binding.
IS-IS view
OSPF view
MR view
Use the sipcommand to access SIP client view.
Voice view
3Com Router 5000/6000 Family
Command Reference
139
sip-call
Use the sip-callcommand to enable globally supplementary service. body style (undo command
description goes here)
SIP Client view
SIP Client view
SIP Client view
SIP Client view
SIP Client view
SIP Client view
sip-comp
Use the sip-compcommand to configure a SIP compatibility option.
Use the sip-compcommand to configure a SIP compatibility option.
Use the sip-comp agentcommand to configure including user-agent field in SIP request.
Use the sip-domaincommand to configure the domain name of a SIP server.
Use the sip-idcommand to set ID of the local gateway and configure its SIP authentication password.
sip-comp
sip-comp agent
sip-domain
sip-id
sip-server
Use the sip-server command to configure address information of SIP proxy server and define call
requests that can be accepted.
SIP Client view
selectlanguage
Use the selectlanguagecommand to enable or disable the voice gateway to play the prompt language
selection message in the voice caller number process. This command only applies to the voice caller
number process.
Voice Access-Number view
Analog E&M Voice Subscriber-Line view
System view
slic-gain
Use the slic-gaincommand to configure the output gain of the SLIC chip.
Use the snmp-agentcommand to enable SNMP agent.
snmp-agent
snmp-agent community
Use the snmp-agent communitycommand to configure the read/write attribute of a community, the MIB
view that it can access, and the ACL applied to it. The configuration overwrites the old configuration of the
community, if there is any.
System view
snmp-agent group
Use the snmp-agent groupcommand to configure a new SNMP group, or to map an SNMP user or group
to an SNMP view.
System view
System view
System view
snmp-agent local-engineid
Use the snmp-agent local-engineidcommand to configure an engine ID for the local SNMP entity.
snmp-agent mib-view
Use the snmp-agent mib-viewcommand to create or update the information about a view.
snmp-agent packet max-size
Use the snmp-agent packet max-sizecommand to set the maximum length of the SNMP packets that the
agent can receive/send.
System view
System view
snmp-agent sys-info
Use the snmp-agent sys-infocommand to set system information, including system contact, physical
location of the node, and SNMP version.
140
3Com Router 5000/6000 Family
Command Reference
snmp-agent target-host
Use the snmp-agent target-hostcommand to set the destination that receives SNMP notifications.
Use the snmp-agent target-hostcommand in conjunction with the snmp-agent trap enable command.
System view
System view
snmp-agent trap enable
Use the snmp-agent trap enablecommand to enable the device to send traps and set the trap and
notification parameters.
snmp-agent trap enable encrypt-card
Use the snmp-agent trap enable encrypt-cardcommand to enable SNMP agent trap function on the
encryption card.
System view
System view
System view
snmp-agent trap enable ldp
Use the snmp-agent trap enable ldpcommand to enable Trap function in MPLS LDP creation.
snmp-agent trap enable lsp
Use the snmp-agent trap enable lspcommand to enable Trap function in MPLS LSP creation.
snmp-agent trap enable mobile-ip
Use the snmp-agent trap enable mobile-ipcommand to enable the MIP SNMP trap function. With the
function enabled, a trap packet is sent to the network management software whenever a security violation
event occurs.
System view
System view
snmp-agent trap enable ospf
Use the snmp-agent trap enable ospfcommand to enable the TRAP function of OSPF.
snmp-agent trap life
Use the snmp-agent trap life command to set the lifetime of traps. The expired traps are discarded
without being retained or sent.
System view
System view
System view
System view
snmp-agent trap queue-size
Use the snmp-agent trap queue-size command to set the length of the trap queue to the specified host.
snmp-agent trap source
Use the snmp-agent trap sourcecommand to specify the source address of traps.
snmp-agent usm-user
Use the snmp-agent usm-usercommand to add a new user to an SNMP group.
sot counter keepalive
Use the sot counter keepalivecommand to specify the number of keepalive checks before disconnecting
from the peer SOT entity.
System view
sot gather
Use the sot gathercommand to assign the serial interface to an existing SOT protocol group.
Synchronous Serial Interface view
sot group-set
sot peer
Use the sot group-setcommand to set up a SOT protocol group.
System view
Use the sot peercommand to assign an IP address to the local SOT entity.
System view
sot sdlc broadcast
Use the sot sdlc broadcastcommand to configure the broadcast address FF for the connected SDLC
terminals, allowing them to receive broadcast frames.
Synchronous Serial Interface view
sot sdlc controller
Use the sot sdlc controllercommand to configure the SDLC address of a connected terminal.
Synchronous Serial Interface view
3Com Router 5000/6000 Family
Command Reference
141
sot sdlc-status primary
sot sdlc-status secondary
sot send address
Use the sot sdlc-status primarycommand to set the role of the router to SDLC primary node.
Synchronous Serial Interface view
Use the sot sdlc-status secondarycommand to set the role of the router to SDLC secondary node.
Synchronous Serial Interface view
Use the sot send addresscommand to configure the route for sending SDLC frames to the specified
specific terminal.
Synchronous Serial Interface view
sot send all tcp
sot timer keepalive
source
Use the send all tcpcommand to forward all received SDLC frames to the specified address.
Synchronous Serial Interface view
Use the sot timer keepalivecommand to configure the keepalive timer.
System view
Use the tunnel sourcecommand to specify the source IP address or source interface to be filled in the
added IP header at the time of tunnel interface encapsulation.
Tunnel Interface view
source-interface
source-ip
Use the source-interface command to configure the source interface in the transmitted test packets.
HWPing Test Group view
Use the source-ipcommand to configure a source IP address for this test.
HWPing Test Group view
source-ip
Use the source-ipcommand to bind a source IP address to the router when it functions as a User Agent
(UA).
SIP Client view
PIM view
source-policy
Use the source-policycommand to configure a router to filter the multicast data packet received according
to source (group) address.
source-port
Use the source-portcommand to configure a source port number for this test.
HWPing Test Group view
special-character
Use the special-charactercommand to configure the supported special characters during register signal
exchange.
R2 CAS view
Voice Dial Program view
Ethernet Interface view
Ethernet Port view
special-service
Use the special-servicecommand to enable or disable the special-service numbers.
Use the speedcommand to set the operating speed of the Ethernet interface.
Use the speedcommand to configure the rate of the port.
Use the speedcommand to set the transmission rate on the user interface.
speed
speed
speed
User Interface view
spf-delay-interval
Use the spf-delay-interval command to configure the interval for actively releasing CPU in the SPF
calculation.
IS-IS view
142
3Com Router 5000/6000 Family
Command Reference
spf-schedule-interval
Use the spf-schedule-intervalcommand to configure the route calculation interval of OSPF.
OSPF view
IS-IS view
spf-slice-size
Use the spf-slice-size command to configure whether to set slice and the duration time each time when
IS-IS performs SPF route calculation.
spt-switch-threshold
Use the spt-switch-thresholdcommand to set the packet rate threshold when the PIM leaf router
switches from the RPT to the SPT.
PIM view
ssh authentication-type default
Use the ssh authentication-type defaultcommand to specify a default authentication mode for SSH
users.
System view
System view
System view
System view
ssh client assign rsa-key
Use the ssh client assign rsa-keycommand to associate an SSH server with the name assigned to its
public key. When connecting to this server, the client verifies its trustworthiness based on this association.
ssh client first-time enable
Use the ssh client first-time enablecommand to enable the SSH client to perform first-time
authentication on SSH servers.
ssh server authentication-retries
Use the ssh server authentication-retriescommand to set the number of SSH connection
authentication retries, which is validated at next login.
ssh server compatible_ssh1x enable
Use the ssh server compatible_ssh1x enablecommand to enable the SSH server to work with SSH1.X
clients.
System view
System view
ssh server rekey-interval
Use the ssh server rekey-intervalcommand to set the interval for updating the server key.
ssh-server source-interface
Use the ssh-server source-interfacecommand to specify a source interface, which must be an existing
local interface, for the SSH server. After that, the IP address of the specified interface is used as the source
IP address in each packet sent by the SSH server.
System view
System view
ssh-server source-ip
ssh server timeout
Use the ssh-server source-ipcommand to specify a source IP address for the packets sent by the SSH
server. This IP address must be a local IP address.
Use the ssh server timeoutcommand to set a timeout for SSH connection authentication at login. It
becomes valid at next login.
System view
System view
ssh user
Use the ssh usercommand to create an SSH user.
ssh user assign
Use the ssh user assigncommand to assign one existing public key to a user. If a key exists, the new
assignment overrides.
System view
System view
ssh user authentication-type
Use the ssh user authentication-typecommand to create an SSH user and specify an authentication
mode for it.
3Com Router 5000/6000 Family
Command Reference
143
ssh user service-type
Use the ssh user service-typecommand to specify service type for a user.
System View
System view
ssh2
Use the ssh2command to initiate a connection to the specified SSH server, and specify the preferred key
exchange algorithm, encryption algorithm and HMAC algorithm between the client and the server.
ssh2 source-interface
Use the ssh2 source-interfacecommand to specify a source interface, which must be an existing local
interface, for the SSH client. After that, the IP address of the specified interface is used as the source IP
address in each packet sent by the SSH client.
System view
System view
ssh2 source-ip
Use the ssh2 source-ipcommand to specify a source IP address for the packets sent by the SSH client.
This IP address must be a local IP address.
standby bandwidth
Use the standby bandwidth command to configure the actual bandwidth that the main interface uses in
backup load sharing.
Interface view
Interface view
Interface view
standby detect-group
standby interface
Use the standby detect-groupcommand to implement interface backup using the auto detect function.
Use the standby interfacecommand to specify a physical interface to back up the interface.
standby routing-group
Use the standby routing-groupcommand to apply a dynamic routing standby group on the secondary
interface.
Dial Interface view
standby routing-rule
Use the standby routing-rulecommand to create a dynamic routing standby group and assign a
monitored network segment to it.
System view
Interface view
standby threshold
Use the standby thresholdcommand to configure backup load sharing on an interface or logical channel.
standby timer delay
Use the standby timer delaycommand to set failover and fallback delays on the interface, avoiding
frequent switchover caused by instability of interface state.
Interface view
Interface view
standby timer flow-check
Use the standby timer flow-checkcommand to configure the interval for checking the traffic size on the
main interface.
standby timer routing-disable
Use the standby timer routing-disablecommand to specify a delay for the secondary link to be
disconnected after the primary link goes up to avoid route oscillation.
Dial Interface view
start l2tp
Use the start l2tpcommand to specify conditions triggering the local end to place calls when it works as
L2TP LAC.
L2TP Group view
L2TP Group view
User view
start l2tp tunnel
start script
Use the start l2tp tunnelcommand to enable the L2TP LAC to start L2TP tunnel connection.
Use the start-scriptcommand to configure executing the specified Modem script on an interface.
144
3Com Router 5000/6000 Family
Command Reference
startup saved-configuration
Use the startup saved-configurationcommand to specify the configuration file used at next startup.
User view
state
Use the statecommand to configure the state of the current ISP domain or local user.
ISP Domain view
Local User view
state
state
Use the statecommand to clarify the name of the state where an entity lies.
Use the statecommand to configure the state of a RADIUS server.
PKI Entity view
RADIUS view
static-bind ip-address
Use the static-bind ip-addresscommand to configure an IP address for a static address binding in
DHCP address pool view.
DHCP Address Pool view
static-bind { mac address | client identifier }
Use the static-bind { mac-address | client-identifier } command to configure a MAC address or
client identifier for a static binding.
DHCP Address Pool view
static-lsp egress
Use the static-lsp egresscommand to configure a static LSP for an egress LSR.
MPLS view
static-lsp egress l2vpn
Use the static-lsp egress l2vpncommand to configure a static LSP used in L2VPN for egress LSR.
MPLS view
MPLS view
MPLS view
MPLS view
MPLS view
PIM view
static-lsp ingress
Use the static-lsp ingresscommand to configure a static LSP for the ingress LSR.
static-lsp ingress l2vpn
Use the static-lsp egress l2vpncommand to configure a static LSP used in L2VPN for ingress LSR.
static-lsp transit
Use the static-lsp transitcommand to configure a static LSP for a transit LSR.
static-lsp transit l2vpn
Use the static-lsp transitcommand to configure a static LSP used in L2VPN for transit LSR.
static-rp
Use the static-rpcommand to configure static RP.
static-rpf-peer
Use the static-rpf-peercommand to configure static RPF peer.
MSDP view
statistics {interval interval | max-group number }
Use the statistics{ interval interval| max-group number} command to configure the statistics
interval and the maximum number of the groups of the retained statistics information according to the
configuration.
HWPing Test Group view
statistics keep-time
Use the statistics keep-timecommand to configure the retaining time of the test statistics.
HWPing Test Group view
stop-accounting-buffer enable
Use the stop-accounting-buffer enablecommand to enable the router to buffer the stop-accounting
requests that have no responses.
RADIUS view
3Com Router 5000/6000 Family
Command Reference
145
stopbits
Use the stopbitscommand to set the stop bits on the user interface.
User Interface view
OSPF Area view
Voice view
stub
Use the stubcommand to configure the type of an OSPF area as the STUB area.
Use the subscriber-linecommand to enter the voice subscriber-line view.
subscriber-line
subscriber-line
Use the subscriber-linecommand to enter FXS, FXO, analog E&M, or digital E1/T1 voice subscriber-line
view.
Any Voice view except for Voice Entity view
substitute
Use the substitutecommand to bind the calling/called number-substitute list to the voice subscriber-line
or voice entity.
Voice Entity View
Voice Subscriber-Line view
substitute incoming-call
Use the substitute incoming-call command to bind the calling/called numbers of the incoming calls
from the network side to the number-substitute list.
Voice Dial Program view
substitute outgoing-call
Use the substitute outgoing-call command to bind the calling/called numbers of the outgoing calls from
the network side to the number-substitute list.
Voice Dial Program view
summary
Use the summarycommand to configure automatic aggregation of sub-network routes.
BGP Multicast view
BGP Unicast view
VPN Instance view
summary
summary
super
Use the summarycommand to configure IS-IS route summary.
IS-IS view
RIP view
Use the summarycommand to enable RIP-2 automatic route summarization.
Use the supercommand to switch the current user level to a specified user level, or the command level that
the user can access.
User view
User Interface view
System view
super authentication mode
Use the super authentication-modecommand to configure authentication mode for the super command,
which can be configured to the following four modes:
super password
Use the super passwordcommand to set the password needed to switch from a lower user level to a higher
one.
sync-clock enable
sync-clock interval
synchronize arp
Use the sync-clock enablecommand to enable clock synchronization between the router and the OSM
board.
GigabitEthernet Interface view
Use the sync-clock intervalcommand to set clock synchronization interval between the router and the
OSM board.
GigabitEthernet Interface view
Use the synchronize arpcommand to enable authorized ARP for global DHCP address pools.
Global DHCP Address Pool view
146
3Com Router 5000/6000 Family
Command Reference
sysname
Use the sysnamecommand to set the name of the router.
System view
User view
system-view
t1 bert
Use the system-viewcommand to enter system view from the current user view.
Use the t1 bertcommand to start a BERT test on the specified T1 line on the CT3 interface.
Use the t1 channel-setcommand to bundle timeslots on the T1 channel.
CT3 Interface view
CPOS Interface view
CT3 Interface view
CT3 Interface view
CPOS Interface view
CT3 Interface view
CT3 Interface view
CPOS Interface view
CT3 Interface view
CPOS Interface view
CT3 Interface view
CT3 Interface view
CPOS Interface view
CT3 Interface view
CPOS Interface view
CT3 Interface view
Interface view
t1 channel-set
t1 channel set
t1 sendloopcode
t1 set clock
t1 set clock
t1 set fdl
Use the t1 channel-setcommand to bundle the timeslots of a T1 line.
Use the t1 sendloopcodecommand to set the loopback mode of the specified far-end T1 line.
Use the t1 set clockcommand to configure the clock mode of T1 channel.
Use the t1 set clockcommand to set the clock mode for a T1 line on the CT3 interface.
Use the t1 set fdlcommand to set the behavior of the specified T1 line on the FDL in ESF framing.
Use the t1 set frame-formatcommand to set a frame format for T1 channel.
Use the t1 set frame-formatcommand to configure the frame format of T1 line.
Use the t1 set loopbackcommand to configure the loopback mode of the T1 channel.
Use the t1 set loopbackcommand to set the loopback mode of a T1 line on the T3 interface.
Use the t1 showcommand to view the line state of the specified T1 line on the CT3 interface.
Use the t1 shutdowncommand to shut down a T1 channel.
t1 set frame-format
t1 set frame-format
t1 set loopback
t1 set loopback
t1 show
t1 shutdown
t1 shutdown
t1 unframed
t1 unframed
tcp mss
Use the t1 shutdowncommand to shut down a T1 line on the CT3 interface.
Use the t1 unframedcommand to set a T1 channel on the CPOS interface to unframed mode.
Use the t1 unframedcommand to set a T1 line on the CT3 interface to work in unframed mode (T1 mode).
Use the tcp msscommand to designate a value as a threshold for TCP packets to be fragmented.
3Com Router 5000/6000 Family
Command Reference
147
tcp timer fin-timeout
Use the tcp timer fin-timeoutcommand to configure the TCP finwait timer.
System view
System view
tcp timer syn-timeout
Use the tcp timer syn-timeoutcommand to configure the TCP synwait timer.
tcp window
Use the tcp windowcommand to configure the size of the transceiving buffer of the connection-oriented
Socket.
System view
User view
telnet
Use the telnetcommand to telnet from this router to another device.
telnet-server source-interface
Use the ftp-server source-interfacecommand to specify a source interface, which must be an existing
local interface, for the Telnet server. After that, the IP address of the specified interface is used as the source
IP address in each packet sent by the Telnet server.
System view
System view
telnet-server source-ip
Use the telnet-server source-ipcommand to specify a source IP address for the packets sent by the
Telnet server. This IP address must be a local IP address.
telnet source-interface
Use the telnet source-interfacecommand to telnet from the main IP address of the specified interface
to the destination IP address.
User view
System view
telnet source-ip
Use the telnet source-ipcommand to telnet from the specified source IP address to the specified
destination IP address.
User view
System view
terminal debugging
terminal logging
terminal monitor
Use the terminal debuggingcommand to have the debugging information displayed on the user terminal.
Use the terminal loggingcommand to have the log information displayed on the terminal.
User view
User view
Use the terminal monitorcommand to have the terminal display debugging /log/trap information sent from
the info-center.
User view
User view
terminal trapping
terminal type
terminator
Use the terminal trappingcommand to have the terminal display trap information.
Use the terminal typecommand to set the terminal type.
User Interface view
Use the terminatorcommand to configure a special character string as the terminator of a telephone
number whose length is variable.
Voice Dial Program view
test-enable
Use the test-enablecommand to execute an HWPing test.
HWPing Test Group view
test-failtimes
Use the test-failtimescommand to configure the number of consecutive test failures allowed before a
trap is sent to the NMS.
HWPing Test Group view
148
3Com Router 5000/6000 Family
Command Reference
test-time begin
test-type
tftp
Use the test-time begincommand to configure the start time and the lasting time of a test.
Use the test-typecommand to configure the type of the test.
HWPing Test Group view
HWPing Test Group view
User view
Use the tftpcommand to upload or download a file through TFTP.
tftp host source-interface
Use the tftphostsource-interfacecommand to specify the source interface that the TFTP client uses
when accessing the specified TFTP server.
User view
User view
tftp host source-ip
Use the tftphostsource-ipcommand to specify the source IP address that the TFTP client uses when
accessing the specified TFTP server. This source IP address must be a local address.
tftp hostname vpn-instance
Use the tftp hostname vpn-instanceto adopt VPN instance mode to access TFTP server and upload
and download files.
User view
System view
System view
System view
tftp-server acl
Use the tftp-server aclcommand to reference an ACL to control access to the TFTP server.
Use the tftp-server directorycommand to configure the directory TFTP Client can access.
Use the tftp-server enablecommand to enable TFTP Server.
tftp-server directory
tftp-server enable
tftp-server max-users
Use the tftp-server max-userscommand to maximum number of concurrent users that are allowed to
access TFTP server.
System view
tftp-server retry-times
Use the tftp-server retry-timescommand to configure maximum number of retry times for TFTP server
timeout retransmission.
System view
System view
tftp-server timeout
tftp-server update
Use the tftp-server timeoutcommand to configure UDP packet response timeout time for TFTP server.
Use the tftp-server updatecommand to set the file update mode that the FTP server uses while receiving
data.
System view
tftp source-interface
Use the ftp source-interfacecommand to specify a source interface, which must be an existing local
interface, for the TFTP client.
System view
System view
tftp source-ip
time-out
Use the ftp source-ipcommand to specify a source IP address for the packets sent by the TFTP client.
Use the time-outcommand to configure the time waiting for a DPD acknowledgement.
Use the time-rangecommand to specify a time range.
DPD Structure view
System view
time-range
3Com Router 5000/6000 Family
Command Reference
149
timeout
Use the timeoutcommand to configure a timeout time for a test.
HWPing Test Group view
timer (Digital E&M)
timer configuration
timer-dial-interval
Use the timercommand to configure the timeout values of the signals in the digital E&M signaling.
Digital E&M Voice Subscriber-Line view
ES-IS view
Use the timer configurationcommand to set the interval to send ISH packets.
Use the timer dial-intervalcommand to configure the timer that the system waits for a subscriber to
dial the next digit.
Voice Subscriber-Line view
timer dl (R2)
Use the timer dlcommand to configure the timeout value of line signals of R2 signaling.
Use the timer dtmfcommand to configure the time interval for sending DTMF signals.
R2 CAS view
R2 CAS view
timer dtmf (R2)
timer first-dial
Use the timer first-dial command to configure the timer that the system waiting for a subscriber to dial
the first digit.
Voice Subscriber-Line view
timer hold
Use the timer holdcommand to set the polling interval.
Interface view
timer hold
Use the timer holdcommand to configure the polling timer at the DTE side.
Use the timer holdcommand to set the timer to send keepalive packet.
Interface view
timer hold
Serial Interface view
ES-IS view
timer holding
Use the timer holdingcommand to set the holding time of the information ISH packets sent carry.
Use the timer keep-alive holdcommand to configure the Keepalive and Holdtime timer of BGP.
timer keep-alive hold
BGP Unicast view
BGP Multicast view
VPNv4 view
VPN Instance view
timer loop
Use the timer loopcommand to set the auto detect interval, that is, the frequency for auto detect.
Detect Group view
timer lsp-max-age
Use the timer lsp-max-age command to configure the maximum lifetime of an LSP generated by the
current router.
IS-IS view
IS-IS view
timer-lsp-refresh
timer quiet
Use the timer lsp-refresh command to configure the refresh interval of LSP.
Use the timer quietcommand to set the duration that the primary server must wait before it can resume
the active state.
RADIUS view
timer quiet
Use the timer quietcommand to set the duration that a primary server must wait before it can resume the
active state.
TACACS+ view
150
3Com Router 5000/6000 Family
Command Reference
timer realtime-accounting
timer realtime-accounting
tUse the timer realtime-accountingcommand to configure a real-time accounting interval.
RADIUS view
Use the timer realtime-accountingcommand to configure a real-time accounting interval.
TACACS+ view
timer register-complete (R2)
Use the timer register-completecommand to configure the timeout value for register signals of R2
signaling.
R2 CAS view
timer register-pulse (R2)
Use the timer pulse command to configure the persistence time of the register pulse signal of R2 signaling
(A3, A4 and A6, etc.).
R2 CAS view
RADIUS view
TACACS+ view
MSDP view
timer response-timeout
Use the timer response-timeoutcommand to configure the RADIUS server response timer.
timer response-timeout
Use the timer response-timeoutcommand to set the response timeout timer of the TACACS server.
timer retry
Use the timer retrycommand to configure the value of connection request re-try period.
timer ring (R2)
Use the timer ringcommand to configure the maximum time range before the signal tone of R2 signaling
is sent.
R2 CAS view
timer ring-back
Use the timer ring-backcommand to configure the maximum duration for the system to send the ringback
tone.
Voice Subscriber-Line view
timer spf
Use the timer spfcommand to configure the interval for the SPF calculation.
Use the timer waitcommand to set a timeout period for a probing attempt.
IS-IS view
timer wait
Detect Group view
timer wait-digit
Use the timer wait-digitcommand to configure the maximum time duration that the system waits for a
digit.
Voice Subscriber-Line view
timers
Use the timerscommand to modify value for the three timers, Period update, Timeout and
Garbage-collection, of RIP.
RIP view
timeslot-set
Use the timeslot-setcommand to configure the timeslot set to perform R2 signaling and digital E&M
signaling configurations.
CE1/PRI Interface view
Voice Entity view
timestamp
Use the timestampcommand to enable the local end to send voice packets with timestamps.
Use the toscommand to assign a value to the ToS field in the header of HWPing test packets.
tos
HWPing Test Group view
trace interval
Use the trace intervalcommand to configure the interval for information recording in the debugging
process, that is, the number of voice packets upon the pass of which a record will be made.
Voice view
3Com Router 5000/6000 Family
Command Reference
151
tracert
Use the tracertcommand to trace the gateways by which a packet passes from source to destination for
network connectivity test and fault location.
Any view
Any view
tracert clns
Use the tracert clnscommand to track the nodes along the route that leads to a specified destination.
Use the traffic behaviorcommand you can define a traffic behavior and enter the behavior view.
Use the traffic classifiercommand to define a class and enter the class view.
Use the traffic-policycommand to associate a sub-policy to the behavior.
traffic behavior
traffic classifier
traffic-policy
System view
System view
Traffic Behavior view
traffic-shaping adaptation
Use the traffic-shaping adaptationcommand to enable the adaptive traffic shaping function of frame
relay.
Frame Relay Class view
traffic-share-across-interface
Use the traffic-share-across-interfacecommand to enable RIP to distribute traffic equally on multiple
interfaces using equal-cost routes.
RIP Protocol view
RIP MBGP Address Family view
transform
Use the transformcommand to set a security protocol used by a proposal.
IPSec Proposal view
translate ip
translate x25
transmit gain
transmit-priority
Use the translate ipcommand to configure an X2T forwarding route from IP network to X.25 network.
Use the translate x25command to configure an X2T forwarding route from X.25 network to IP network.
Use the transmit gaincommand to configure the voice subscriber-line output end gain value.
System view
System view
Voice Subscriber-Line view
Use the transmit-prioritycommand to assign a transmit priority to the ATM PVC associated with the
UBR, VBR-T, or VBR-NRT service. The higher priority PVC is allocated bandwidth before any other PVCs.
ATM PVC view
R2 CAS view
trunk-direction
trunk-id
Use the trunk-directioncommand to configure the E1 trunk direction.
Use the trunk-idcommand to configure the number that the local end dials to call the PSTN side in FRF.11
trunk mode.
Voice Entity view
R2 CAS view
ts
Use the tscommand to maintain the trunk circuit of the specified timeslot.
Use the ttlcommand to configure TTL of ICMP test packets.
ttl
HWPing Test Group view
ttl expiration
Use the ttl expirationcommand to configure the router to forward ICMP responses by local IP routing
when the MPLS TTL expires.
MPLS view
152
3Com Router 5000/6000 Family
Command Reference
ttl propagate
Use the ttl propagatecommand to enable IP TTL duplication of MPLS.
MPLS view
tunnel authentication
Use the l2tp tunnel authenticationcommand to enable L2TP tunnel authentication.
L2TP Group view
tunnel avp-hidden
Use the tunnel avp-hiddencommand to configure Attribute Value Pair (AVP) data to be transmitted in
hidden format.
L2TP Group view
L2TP Group view
tunnel flow-control
tunnel local
Use the tunnel flow-controlcommand to enable L2TP tunnel flow-control.
Use the tunnel localcommand to set the local address of an ipsec policy.
Manually-Established IPSec Policy view
tunnel keepstanding
Use the tunnel keepstanding command to enable the tunnel-hold function of L2TP, preventing the tunnel
from being disconnected when no session is present.
L2TP Group view
L2TP Group view
tunnel name
Use the tunnel namecommand to specify local name of a tunnel.
tunnel-on
Use the tunnel-oncommand to enable tunnel function.
VoIP Voice Entity view
L2TP Group view
tunnel password
tunnel-protocol dvpn
tunnel-protocol gre
tunnel remote
tunnel timer hello
type
Use the tunnel passwordcommand to specify a password for tunnel authentication.
Use the tunnel-protocol udp dvpncommand to encapsulate a tunnel interface with UDP DVPN.
Use the tunnel modecommand to set encapsulation mode of the tunnel interface to GRE.
Use the tunnel remotecommand to set the remote address of an ipsec policy.
Tunnel Interface view
Tunnel interface view
Manually-Established IPSec Policy view
Use the tunnel timer hellocommand to set a Hello packet forwarding interval.
Use the typecommand to configure the analog E&M subscriber-line signal type.
L2TP Group view
Voice Subscriber-Line view
type-number
Use the type-numbercommand to configure the calling/called number types of voice entities.
Use the udp-helper enablecommand to enable UDP Helper.
Voice Entity view
System view
udp-helper enable
udp-helper port
Use the udp-helper portcommand to specify the UDP port number in the UDP broadcasts to be
forwarded.
System view
udp-helper server
Use the udp-helper servercommand to configure the destination server to which the UDP broadcasts
received on the interface are forwarded.
Ethernet Interface view
3Com Router 5000/6000 Family
Command Reference
153
undelete
Use the undeletecommand to restore a file from the recycle bin.
User view
User view
undo schedule reboot
undo synchronization
Use the undo schedule rebootcommand to cancel the configuration of the schedule reboot terminal
service.
Use the undo synchronizationcommand to remove the synchronization between BGP and IBGP.
BGP view
VPN Instance view
upgrade
Use the upgradecommand to upgrade the Boot ROM program, pico-code or the logic.
Use the upgradecommand to upgrade the Boot ROM.
System view
User view
upgrade
upgrade flash
Use the upgrade flash command to upgrade the software of the card. To have the upgraded software take
effect, reboot the router.
ATM (ADSL) Interface view
use encrypt-card
Use the use encrypt-cardcommand to specify the SA proposal uses the encryption card at a designated
slot.
Card SA Proposal view
user
user
Use the usercommand to register an FTP user.
FTP Client view
Use the usercommand to configure username, password and corresponding display mode in SIP client
view and/or voice entity view. The configurations of the cnonce and realm authentication information fields
are optional, which can be used for authentication.
SIP Client view
Voice Entity view
user-interface
Use the user-interfacecommand to enter single-user interface view or multi-user interface view.
System view
user-name-format
Use the user-name-formatcommand to configure the format of the username to be sent to a RADIUS
server.
RADIUS view
user-name-format
user privilege
Use the user-name-formatcommand to configure the username format sent to the TACACS server.
TACACS+ view
Use the user privilege command to configure the command level that the login users on the current user
interface can access.
User Interface view
username
Use the usernamecommand to configure a name used for logging onto the FTP server.
HWPing Test Group view
CE1/PRI Interface view
CE3 Interface view
using (CE1/PRI Interface)
Use the usingcommand to configure the operating mode of the CE1/PRI interface.
using (CE3 Interface)
Use the usingcommand to configure the operating mode of a CE3 interface.
154
3Com Router 5000/6000 Family
Command Reference
using (CT3 Interface)
Use the usingcommand to configure the operating mode of a CT3 interface.
CT3 Interface view
Voice Entity view
vad-on
Use the vad-oncommand to enable silence detection function.
validate source address
Use the validate-source-addresscommand to enable checking of the source address of a RIP packet
upon reception.
RIP Protocol view
RIP MBGP Address Family view
verbose
Use the verbosecommand to enable the verbose function to view information from the FTP server.
FTP Client view
System view
vfs check check-method discard
Use the vfs check check-method discardcommand to specify the file discarding method to be the file
system check method.
vfs check check-method discard auto
Use the vfs check check-method discard autocommand to specify to discard the contents of corrupted
files and then recycle the corresponding storage space automatically.
System view
System view
vfs check check-method fix
Use the vfs check check-method fixcommand to set the file check method to automatic file fixing.
vfs check file-system
Use the vfs check file-systemcommand to check the file system. At present, the system can check
corrupted files and perform operations such as file fixing/discarding and space recycling.
User view
vi-card busy-tone-detect
Use the vi-card busy-tone-detectcommand to configure busy tone detection method on FXO
subscriber-line.
Voice view
Voice view
vi-card cptone-custom
Use the vi-card cptone-customcommand to set the prompt tone parameters of the system.
vi-card custom-toneparam
Use the vi-card custom-toneparamcommand to save DSP parameters and customize busy tone
detection parameters on the FXO interface.
Voice view
Voice view
vi-card reboot
virtualbaudrate
vlan-type dot1q vid
vlink-peer
Use the vi-card rebootcommand to reboot a voice card.
Use the virtualbaudratecommand to set a virtual baudrate for the DTE interface.
Use the vlan-type dot1q command to set the encapsulation types on the sub-interface.
Use the vlink-peercommand to create and configure a virtual link.
Use the vofrcommand to enable VoFR operation mode for a DLCI.
Synchronous Serial Interface view
Interface view
OSPF Area view
vofr
DLCI view
vofr frf11-timer
Use the vofr frf11-timercommand to configure the interval of Trunk Wait timer in FRF.11 trunk mode.
Voice view
3Com Router 5000/6000 Family
Command Reference
155
vofr jitter-buffer
Use the vofr jitter-buffercommand to configure a jitter buffer length.
Voice view
voice bandwidth
voice-config
Use the voice bandwidthcommand to configure maximum bandwidth for voice calls.
Frame Relay Class view
Use the voice-configcommand to enable the DHCP server to send option 184 and suboptions of 184
when it assigns addresses from the global address pool.
DHCP Address Pool view
voice-setup
Use the voice-setupcommand to enter voice view and enable voice services.
System view
voip call-start
voip calledtunnel
Use the voip call-startcommand to configure a call initialization mode for the called GW.
Use the voip calledtunnel enablecommand to enable the tunnel function on the called gateway.
Voice view
Voice view
voip h323-conf tcs-t38
Use the voip h323-conf tcs-t38command to enable the voice gateway to include the T.38 capability
description in its capability set when it is in H.323 slow-start mode.
Voice view
Voice view
Voice view
voip h323-descriptor
Use the voip h323-descriptorcommand to configure the description character string of the voice gateway
H.323.
voip timer
Use the voip timercommand to set the VoIP-to-POTS timer, or the delay waiting for switching from VoIP
entity to backup POTS entity after a VoIP call is failed.
vpinstance
Use the vpninstancecommand to specify a VPN instance.
HWPing Test Group view
OSPF Protocol view
MBGP VPN-Instance view
Voice view
vpn-instance-capability simple
Use the routing-table limitcommand to configure a router as Multi-VPN-Instance CE.
vpn-target
Use the vpn-targetcommand to create vpn-target extended community for vpn-instance.
Use the vqa data-statisticcommand to enable counting of voice data.
vqa data-statistic
vqa dscp
Use the vqa dscpcommand to set the global DSCP value in the ToS field in the IP packets that carry the
RTP stream or voice signaling.
Voice view
Voice view
Voice view
vqa dsp-monitor
vqa jitter-buffer
vqa performance
Use the vqa dsp-monitorcommand to set duration for DSP buffer data monitoring.
Use the vqa jitter-buffercommand to configure jitter buffer depth.
Use the vqa performancecommand to configure the sending or receiving process of voice data to fast or
normal forwarding process.
Voice view
156
3Com Router 5000/6000 Family
Command Reference
vrbd
Use the vrbdcommand to view software version details, including product software version and the
matched platform software version.
Any view
vrrp authentication-mode
Use the vrrp authentication-modecommand to configure authentication mode and authentication key for
the VRRP standby groups on the interface.
Ethernet Interface view
Bridge Template view
vrrp ping-enable
vrrp un-check ttl
Use the vrrp ping-enablecommand to enable users to ping the virtual IP addresses of standby groups.
System view
Bridge Template view
Use the vrrp un-check ttlcommand to disable the VRRP standby group to check the TTL field in VRRP
packets.
Ethernet Interface view
Bridge Template view
vrrp vrid preempt-mode
Use the vrrp vrid preempt-modecommand to enable preemption on the router and configure its
preemption delay in the specified standby group.
Interface view
bridge Template view
vrrp vrid priority
Use the vrrp vrid prioritycommand to configure the priority of the router in the specified standby group.
Ethernet Interface view
Bridge Template view
vrrp vrid timer advertise
Use the vrrp vrid timer advertisecommand to configure the Adver_Timer of the specified standby
group.
Ethernet Interface view
Bridge Template view
vrrp vrid track
Use the vrrp vrid trackcommand to configure the interface to be tracked.
Ethernet Interface view
Bridge Template view
vrrp vrid track detect-group
Use the vrrp vridcommand to implement VRRP using the auto detect function.
Ethernet Interface view
vrrp vrid virtual-ip
Use the vrrp vrid virtual-ipcommand to create a standby group the first time that you add a virtual IP
address or add a virtual IP address to it after that. Each standby group can accommodate up to 16 virtual
IP addresses.
Ethernet Interface view
Bridge Template view
web java-blocking acl-number
Use the web java-blocking acl-numbercommand to enable ACL-based Java blocking ACL function.
System view
web java-blocking enable
Use the web java-blocking enablecommand to enable Java blocking.
System view
web java-blocking extension add
Use the web java-blocking extension addcommand to add extension name of Java request packets to
be blocked.
System view
System view
web java-blocking extension add-default
Use the the web java-blocking extension add-defaultcommand to add system default Java blocking
keywords after you have defined them.
3Com Router 5000/6000 Family
Command Reference
157
web java-blocking extension delete
Use the web java-blocking extension deletecommand to delete a previously added extension name
of Java request packets.
System view
web java-blocking extension delete-all
Use the web java-blocking extension delete-allcommand to delete all Java blocking keywords
previously added.
System view
System view
System view
System view
System view
web java-blocking extension load-file
Use the web java-blocking extension load-filecommand to load a Java blocking filter file.
web java-blocking extension save-file
Use the web java-blocking extension save-filecommand save a Java blocking filter file.
Use the web log enablecommand to enable web logging and create a logging timer.
Use the web log timercommand to configure the timeout time of the logging timer.
web log enable
web log timer
web url-filter host acl-number
Use the web url-filter host acl-numbercommand to configure the firewall to filter the web requests
whose destination URL address is an IP address by using an ACL.
System view
System view
web url-filter host add
Use the web url-filter host addcommand to add web filtering address, and set the filtering operation.
web url-filter host default
Use the web url-filter host defaultcommand to permit or deny packets that do not match with the
URL addresses configured by the administrator.
System view
System view
System view
System view
web url-filter host delete
Use the web url-filter host deletecommand to a URL address filtering entry previously added.
web url-filter host delete-all
Use the web url-filter host delete-allcommand to delete all URL address filtering entries.
web url-filter host enable
Use the web url-filter host enablecommand to enable URL address filtering.
web url-filter host ip-address
Use the web url-filter host ip-addresscommand to configure whether to permit a web request whose
destination URL address is an IP address to pass.
System view
System view
System view
System view
web url-filter host load-file
Use the web url-filter host load-filecommand to load the URL address filtering file.
web url-filter host save-file
Use the web url-filter host save-filecommand to save a URL address filter file.
web url-filter parameter add
Use the web url-filter parameter addcommand to add a keyword for URL parameter filtering.
web url-filter parameter add-default
Use the web url-filter parameter add-defaultcommand to add default filter keywords ^select^,
^insert^, ^update^, ^delete^, ^drop^, --, ', ^exec^ and %27 to facilitate the user to input these keywords from
being carelessly deleted or to enable the user to restore the default settings quickly if the web url-filter
parameter add-defaultcommand was improperly executed.
System view
158
3Com Router 5000/6000 Family
Command Reference
web url-filter parameter delete
Use the web url-filter parameter deletecommand to delete a filter keyword previously added.
System view
System view
web url-filter parameter delete-all
Use the web url-filter parameter delete-allcommand to delete all filter keywords.
web url-filter parameter enable
Use the web url-filter parameter enablecommand to enable URL parameter filtering.
System view
web url-filter parameter load-file
Use the web url-filter parameter load-filecommand to load a URL parameter filtering file.
System view
web url-filter parameter save-file
Use the web url-filter parameter save-filecommand to save a URL parameter filter file.
System view
wfq
Use the wfqcommand to set the queue type of the VC to be WFQ.
Frame Relay Class view
wildcard-register enable
Use the wildcard-register enablecommand to enable fuzzy (wildcard) telephone number registration.
SIP Client view
wred
Use the wredcommand to configure drop mode as weighted random early detection (WRED).
Traffic Behavior view
wred dscp
Use the wred dscpcommand to set DSCP lower-limit, upper-limit and drop probability denominator of
WRED.
Traffic Behavior view
Traffic Behavior view
wred ip-precedence
Use the wred ip-precedence command to set precedence lower-limit, upper-limit and drop probability
denominator of WRED.
wred weighting-constant
Use the wred weighting-constant command to set exponential for the calculation of average queue
length by WRED.
Traffic Behavior view
Interface view
x25 alias-policy
x25 call-facility
Use the x25 alias-policycommand to configure the alias of an X.121 address.
Use the x25 call-facility command to set user options for an X.25 interface. After an option is set, all
X.25 calls from the X.25 interface will carry the relevant information field in call packet.
Interface view
Interface view
x25 cug-service
Use the x25 cug-servicecommand to enable CUG service and suppression policies.
x25 default-protocol
Use the x25 default-protocolcommand to set the default upper-layer protocol carried over X.25 for the
X.25 interface.
Interface view
x25 default-protocol
Use the x25 default-protocolcommand to set the upper layer protocol for an X.25 interface that X.25
protocol carries by default.
Interface view
System view
x25 hunt-group
Use the x25 hunt-group command to create or enter an X.25 hunt group.
3Com Router 5000/6000 Family
Command Reference
159
x25 ignore called-address
Use the x25 ignore called-address command to enable it to ignore the X.121 address of the called DTE
when X.25 initiates calls.
Interface view
Interface view
Interface view
x25 ignore calling-address
Use the x25 ignore calling-address command to enable it to ignore the X.121 address of the calling
DTE when X.25 initiates calls.
x25 local-cug
Use the x25 local-cugcommand to configure mapping from local CUG to network CUG and define its
suppression rule.
x25 map
Use the x25 mapcommand to set the address mapping between IP address used by LANs and X.121
address.
Interface view
Interface view
Interface view
Interface view
Interface view
Interface view
Interface view
x25 map bridge
x25 map clns
x25 modulo
Use the x25 map bridgecommand to map an X.121 address to a bridge-set.
Use the x25 map clnscommand to configure a CLNS address mapping for an X.121 address.
Use the x25 modulocommand to set the window modulus of an X.25 interface.
Use the x25 packet-sizecommand to set the maximum input and output packet lengths of X.25 interface.
Use the x25 pvccommand to configure one PVC route encapsulated with datagram.
Use the x25 pvccommand to configure an X.25 PVC route.
x25 packet-size
x25 pvc
x25 pvc
x25 qllc-switch
Use the X25 qllc-switchcommand to create a QLLC switching map entry, an association of X.121
address, MAC address of the SNA device, and local virtual MAC address.
Synchronous Serial Interface view
x25 queue-length
Use the x25 queue-lengthcommand to set the data queue length on X.25 VC.
Interface view
x25 receive-threshold
Use the x25 receive-thresholdcommand to set the number of receivable maximum packets before X.25
sends the acknowledged packet.
Interface view
Interface view
Interface view
Interface view
x25 response called-address
Use the x25 response called-addresscommand to enable X.25 to carry the address information of the
called DTE in sending call reception packet.
x25 response calling-address
Use the x25 response calling-addresscommand to enable X.25 to carry the address information of the
calling DTE in sending call reception packet.
x25 reverse-charge-accept
Use the x25 reverse-charge-acceptcommand to enable this interface to accept the call with “reverse
charging request”, the information added by some certain user facilities.
160
3Com Router 5000/6000 Family
Command Reference
x25 roa-list
Use the x25 roa-listcommand to define ROA list.
System view
Interface view
x25 switch pvc
Use the x25 switch pvc(packet switching) command to configure one PVC route.
x25 switch svc hunt-group
Use the x25 switch svc hunt-groupcommand to add an X.25 switching route whose forwarding address
is a hunt group.
System view
System view
x25 switch svc interface
Use the x25 switch svc interfacecommand to add an X.25 switching route whose forwarding address
is a serial interface or Annex G DLCI.
x25 switch svc xot
Use the x25 switch svc xotcommand to add an X.25 switching route whose forwarding address is XOT
channel.
System view
System view
x25 switching
x25 template
Use the x25 switchingcommand to enable the X.25 switching function.
Use the x25 templatecommand in system view to create an X.25 template and in DLCI view to reference
the template.
System view
DLCI view
x25 timer hold
x25 timer idle
x25 timer tx0
x25 timer tx1
Use the x25 timer holdcommand to set the delay to send calls to a destination with failed calls.
Use the x25 timer idlecommand to set the maximum idle time of the SVC on the interface.
Use the x25 timer tx0command to set the restart/retransmission timer delay for DTE (or DCE).
Interface view
Interface view
Interface view
Use the x25 timer tx1command to set calling request (indication) transmission timer delay for DTE (or
DCE).
Interface view
Interface view
Interface view
x25 timer tx2
x25 timer tx3
x25 vc-per-map
Use the x25 timer tx2command to set resetting request (indication) transmission timer delay for DTE (or
DCE).
Use the x25 timer tx3command to set clearing request (indication) transmission timer delay for DTE (or
DCE).
Use the x25 vc-per-mapcommand to set the maximum number of VCs for connections with the same
destination device.
Interface view
Interface view
Interface view
x25 vc-range
Use the x25 vc-rangecommand to set highest and lowest values of X.25 VC range.
x25 window-size
Use the x25 window-sizecommand to set the sizes of input and output windows on the interface X.25.
3Com Router 5000/6000 Family
Command Reference
161
x25 x121-address
Use the x25 x121-addresscommand to set the X.121 address of an X.25 interface.
Interface view
x25 xot pvc
Use the x25 xot pvccommand to add a PVC route of XOT. Use the undo x25 pvccommand to delete the
specified PVC route of XOT.
Interface view
System view
x29 timer idleclear
Use the x29 timer idleclearcommand to set the idle-clear timer for PAD connection.
x29 timer inviteclear-time
Use the x29 timer inviteclear-timecommand to set the delay waiting for response after the PAD clear
procedure is initiated. Upon expiration of this timer, the server aborts the connection by force and starts X.25
clear procedures.
System view
User view
xmodem get
Use the xmodem getcommand to download a file by using Xmodem through the AUX port. Comware
supports 128-byte packets and CRC check.
162
3Com Router 5000/6000 Family
Command Reference
|