User Guide
Self Contained Wireless Alarm System v1.0
N11427
WARNING: This manual contains information on limitations regarding product use and
function and information on the limitations as to liability of the manufacturer.
The entire manual should be carefully read.
Table of Contents
About Your Security System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Fire Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
General System Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Controls & Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Arming & Disarming the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Stay Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Night Arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Silent Exit Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Away Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Quick Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Bell/Siren Sounds After Away Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Remote Arming and Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Emergency Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
When Alarm Sounds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Intrusion (Burglar) Alarm Continuous Siren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Fire Alarm Pulsed Siren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2-Way Audio Audio Operation (SCW9047 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Time & Date Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Bypassing Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Trouble Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Alarm Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Door Chime (Entry/Exit Beeps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Access Code Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Access Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
User Code Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Zone Bypassing Attribute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Bell Squawk Attribute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Erasing an Access Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
User Function Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Changing Brightness/Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Changing the Buzzer Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Viewing the Event Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Testing Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Sounder and Display Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Walk Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Allowing Computer Access To Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
i
Reference Sheets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
System Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Access Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Sensor / Zone Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Guidelines for Locating Smoke Detectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Household Fire Safety Audit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Fire Escape Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Always ensure you obtain the latest version of the User Guide. Updated versions of this User
Guide are available by contacting your distributor.
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electric shock and/or injury, observe the following safety precautions:
•
•
Do NOT spill any type of Liquid On the equipment.
Do NOT attempt to service this product yourself. Opening or removing the cover may expose you to
DANGEROUS VOLTAGES or other risk. Refer SERVICING TO Qualified Service Personnel. NEVER
Open the device yourself.
•
Do NOT touch THE EQUIPMENT AND ITS CONNECTED CABLES DURING AN ELECTRICAL
STORM; THERE MAY BE A REMOTE RISK OF ELECTRIC SHOCK FROM LIGHTNING
Do NOT use the Alarm System to report a gas leak if it is near the leak.
•
REGULAR MAINTENANCE AND TROUBLESHOOTING
Keep your Alarm Controller in optimum condition by following all the instructions that are included within
this Manual and/or marked on the product.
CLEANING
•
•
Clean the enclosure (case) by wiping with a damp cloth only.
DO NOT use abrasives, thinners, solvents or aerosol cleaners (spray polish) that may enter through
holes in the enclosure (case) of the Alarm Controller and cause damage.
DO NOT use any water or any other liquid.
•
•
Do not wipe the front cover with alcohol.
TROUBLESHOOTING
Occasionally, you may have a problem with your Alarm Controller or telephone line. If this happens, your
Alarm Controller usually identifies the problem and displays an error message. Refer to the provided list
when you see an error message on the display. If additional help is required, contact your distributor for
service.
WARNING
This equipment, SCW Alarm System SCW9045/47 shall be installed and used within an environment that
provides the pollution degree max 2 and over-voltages category II NON-HAZARDOUS LOCATIONS,
indoor only. The equipment is DIRECT PLUG-IN connected and is designed to be installed, serviced and/
or repaired by service persons only; [service person is defined as a person having the appropriate
technical training and experience necessary to be aware of hazards to which that person may be exposed
in performing a task and of measures to minimize the risks to that person or other persons].
There are no parts replaceable by the end-user within this equipment.
This publications covers the following models:
•SCW9047-433
•SCW9045-433
ii
About Your Security System
Your Security System has been designed to provide you with the greatest possible flexibility and con-
venience. Read this manual carefully and have your installer instruct you on your system's operation
and on which features have been implemented in your system. All users of this system should be
equally instructed in its use. Fill out the “System Information” page with all of your zone information
and access codes and store this manual in a safe place for future reference.
NOTE: Please consult your installer for further information regarding the false alarm reduction
features built into your system as all are not covered in this manual.
Fire Detection
This equipment is capable of monitoring fire detection devices such as smoke detectors and provid-
ing a warning if a fire condition is detected. Good fire detection depends on having adequate num-
ber of detectors placed in appropriate locations. This equipment should be installed in accordance
with NFPA 72 (N.F.P.A., Battery march Park, Quince MA 02269). Carefully review the Family Escape
Planning guidelines in this manual.
NOTE: Your installer must enable the fire detection portion of this equipment before it becomes
functional.
Testing
To ensure that your system continues to function as intended, you must test your system weekly.
Please refer to the “Testing your System” section in this manual. If your system does not function
properly, call your installing company for service.
Monitoring
This system is capable of transmitting alarms, troubles & emergency information to a central station. If you
initiate an alarm by mistake, immediately call the central station to prevent an unnecessary response.
NOTE: The monitoring function must be enabled by the installer before it becomes functional.
NOTE: This system has a communicator delay of 30 seconds. It can be removed, or it can be
increased up to 45 seconds by the installer.
NOTE: Ensure that your Installer verifies that your system is compatible with the Central Station
Receiver format at yearly intervals.
Maintenance
With normal use, the system requires minimum maintenance. Note the following points:
• Do not wash the security equipment with a wet cloth. Light dusting with a slightly moistened cloth
should remove normal accumulations of dust.
• DSC recommends replacing the standby batteries every 4-5 years.
• For other system devices such as smoke detectors, motion detectors, glassbreak detectors or door/
window contacts, consult the manufacturer’s literature for testing and maintenance instructions if
applicable.
General System Operation
Your security system comprises an integrated alarm control/keypad and various sensors and detec-
tors. The system is mounted by the main exit/entry location. The system is self-contained; electronics
and standby battery are housed within the keypad unit.
NOTE: Only the installer or service professional should have access to the system.
The security system has several zones of area protection. Each of these zones communicates to a sin-
gle wireless sensor (motion detectors, glassbreak detectors, door contacts, etc.) or to one or more
hard wired sensors. A sensor in alarm is indicated by messages on the LCD keypad.
Additional features include: Automatic Inhibit (Swinger Shutdown) for Alarm; Tamper and Trouble
signals after 3 occurrences in a given set period; and a Programmable Keypad Lockout option.
NOTE: For SIA CP-01 classified installations, the swinger shutdown feature is programmed such
that one or two trips will shut down the zone. The zone will be restored after a manual reset (by
entering the access code at the time of disarming the alarm system) or it will be reset automatically
after 48 hrs with no trips on any zones.
1
Controls & Indicators
IMPORTANT NOTICE
A security system cannot prevent emergencies. It is only intended to alert you and – if included – your
central station of an emergency situation. Security systems are generally very reliable but they may
not work under all conditions and they are not a substitute for prudent security practices or life and
property insurance. Your security system should be installed and serviced by qualified security profes-
sionals who should instruct you on the level of protection that has been provided and on system
operations.
Language Selection
Your system can display messages in different languages.
1. Press and hold both
2. Using the
keys simultaneously.
keys, scroll through the available languages.
3. Press
to select your desired language.
Arming & Disarming the System
Stay Arming
Stay arming will bypass the interior protection (i.e. motion sensors) and arm the perimeter of the sys-
tem (i.e. doors and windows). Close all sensors (i.e. stop motion and close doors). The Ready (
indicator should be on.
)
Press and hold the Stay key for 2 seconds and/or enter your Access Code and do not leave the pre-
mises. During the setting state (exit delay active), the Armed ( ) and Ready ( ) indicators will light.
When the exit delay is completed, the alarm system is armed/set and this is indicated on the keypad
as follows: the Ready ( ) indicator will turn off, the Armed ( ) indicator will remain on.
The Armed ( ) indicator and a bypass message will be displayed. The system will automatically
bypass certain interior sensors (i.e. motion sensors).
NOTE: For SIA FAR listed panels, the Stay Arming Exit Delay will be twice as long as the Away
Arming Exit Delay.
NOTE: If your system is installed in accordance with SIA CP-01 Standard for False Alarm
Reduction then the security system will arm in the Stay Armed mode if the exit delay time expires
and no exit has been made.
2
Night Arming
To fully arm the system when it has been armed in Stay Mode, press
rior zones will now be armed except for devices programmed as Night Zones.
at the keypad. All inte-
Night zones are only armed in Away mode, this permits limited movement within the premises when
the system is fully armed. Ensure that your installer has provided you with a list identifying zones pro-
grammed as night zones.
When the interior zones have been activated (i.e.,
) you must enter your access code to dis-
arm the system to gain access to interior areas that have not been programmed as night zones.
Silent Exit Delay
If the system is armed using the Stay key or using the ’No Entry’ Arming method (
code]), the audible progress annunciation (keypad buzzer) will be silenced and the exit time will be
doubled for that exit period only.
[access
Away Arming
Close all sensors (i.e. stop motion and close doors). The Ready ( ) indicator should be on.
To arm, press and hold the Away Key for 2 seconds and/or enter your Access Code, or press
to Quick Arm. During the setting state (exit delay active) the Armed ( ) and Ready ( ) indicators will
turn on, and the keypad will sound one beep per second. You now have ____ seconds to leave the
premises (please check with your installer to have this time programmed). An audible annunciation,
whose pulsating rate is distinctly different, will sound during the last ten seconds of the exit delay to
warn person(s) that the exit delay is running out. To cancel the arming sequence, enter your access
code.
When the exit delay is completed, the alarm system is armed/set and this is indicated on the keypad
as follows: the Ready ( ) indicator will turn off, the Armed ( ) indicator will remain on and the key-
pad will stop sounding.
NOTE: If your system is installed in accordance with SIA CP-01 Standard for False Alarm
Reduction then the violation, restoral followed by a second violation of the entry/exit zone before
the end of the exit delay will restart the exit delay.
Quick Exit
If the system is armed and you need to exit, use the Quick Exit function to avoid disarming and
rearming the system. Press and hold the Quick Exit key for 2 seconds or press
. You now have
2 minutes to leave the premises through your exit door. When the door is closed again, the remain-
ing exit time is cancelled.
Bell/Siren Sounds After Away Arming
Audible Exit Fault
In an attempt to reduce false alarms, the Audible Exit Fault is designed to notify you of an improper
exit when arming the system. In the event that you fail to securely close the Exit/Entry door during
the allotted exit delay period, the system will sound the alarm to indicate an improper exit.
Your installer will tell you if this feature has been enabled on your system. If this occurs:
1. Re-enter the premises.
2. Enter your [access code] to disarm the system. You must do this before the entry delay timer
expires.
3. Follow the Away arming procedure again, ensure that the entry/exit door(s) are secured.
Arming Error
An error tone will sound if the system is unable to arm. This will happen if the system is not ready to
arm (i.e. sensors are open), or if an incorrect user code has been entered. If this happens, ensure all
sensors are secure, press
and try again.
Disarming
Enter your access code to disarm anytime the system is armed (Armed ( ) indicator is on). The key-
pad will sound a continuous tone after the entry delay has been initiated by opening the entry/exit
door. Enter your code within _____ seconds to avoid an alarm condition (check with your installer to
have this time programmed).
Disarming Error
If your code is invalid, the system will not disarm and a 2-second error tone will sound. If this hap-
pens, press
and try again.
3
Remote Arming and Disarming
The system can be armed and/or disarmed (if programmed by the installer) using a remote control
device (wireless key). When arming the system by using the Arm button on the wireless key, the system
will acknowledge the command by sounding a single bell squawk and when disarming using the Dis-
arm button on the wireless key the system will acknowledge the command by sounding two bell
squawks . Three squawks heard when disarming with the disarm button indicates that that an alarm
occurred while the system was armed. If you are unsure of the cause of the alarm, proceed with cau-
tion.
Emergency Keys
Press the
(F),
(A) or
(P) key for 2 seconds to generate a Fire, Auxiliary or Panic alarm. The
keypad sounder will beep indicating that the alarm input has been accepted and transmission to the
central station is underway. The
setup.
(P) key may or may not sound the bell depending on Installer
NOTE: The Fire keys can be disabled by the installer.
When Alarm Sounds
The system can generate 2 different alarm sounds:
• Continuous Siren = Intrusion (Burglary Alarm)
• Temporal / Pulsed Siren = Fire Alarm
Intrusion (Burglary) Alarm Continuous Siren
NOTE: If you are unsure of the source of the alarm, proceed with caution! If the alarm was
accidental, enter your Access Code to silence the alarm. If the alarm system is disarmed within the
programmed Abort Window (check with the installer if this option has been enabled on your system
and what is the transmitter delay time programmed), no alarm transmission to the Central Station
will occur. Starting at the end of the Abort Window there is a five minute Cancel window, during
which a user can cancel, by entering his access code, an alarm that has been previously transmitted.
A cancel signal will be transmitted to the Central Station and the alarm system will also annunciate
that the cancel signal was transmitted. Call your central station to avoid a dispatch.
Fire Alarm Pulsed Siren
Follow your emergency evacuation plan immediately!
If the fire alarm was accidental (i.e. burned toast, bathroom steam, etc.), enter your Access Code to
silence the alarm. Call your central station to avoid a dispatch.
2-Way Audio Operation (SCW9047 only)
If programmed by the installer, this feature allows the monitoring station to initiate a 2-way audio
session when an alarm has been received. This feature is used to verify the nature of the alarm or
determine the type of assistance required by the occupant.
NOTE: This feature can be initiated only by the monitoring station after an alarm has been
received. The user can not initiate a 2-way audio session.
Time & Date Programming
Press
plus your Master Access Code to enter User Functions. Use the
scroll keys to find
to select it. Enter the time in 24-hr. format (HH:MM), followed by the
to exit programming. If you are viewing a ‘Loss of Clock’, trouble from
the menu option then press
date (MM:DD:YY). Press
within the trouble menu (
ble Conditions on page 6),
), press
to directly enter Date and Time programming. See Trou-
NOTE: Your installer may have programmed your system to display the time and date while the key-
pad is idle. Press the
key to clear the date and time display if desired.
Bypassing Zones
Use the zone bypassing feature when you need access to a protected area while the system is armed,
or when a zone is temporarily out of service, but you need to arm the system. Bypassed zones will
not be able to sound an alarm. Bypassing zones reduces the level of security. If you are bypassing a
zone because it is not working, call a service technician immediately so that the problem can be
resolved and your system returned to proper working order. Ensure that no zones are unintentionally
4
bypassed when arming your system. Zones cannot be bypassed once the system is armed. Bypassed
zones are automatically cancelled each time the system is disarmed and must be bypassed again, if
required, before the next arming.
Bypassing Zones
With the system disarmed.
1. Press
2. Press
to enter the function menu. The keypad will display “Press ꢀ for < > Zone Bypass”.
or , then your [access code] (if required). The keypad will display “Scroll to < >
Bypass Zones”.
3. Enter the two-digit number of the zone(s) to be bypassed (01-34).
You can also use the keys to find the zone to be bypassed, and then press
to select the
zone. The keypad will display “Zone Name”. “B” will appear on the display to show that the zone is
bypassed. If a zone is open (e.g., door with door contact is open), the keypad will display “Zone Name”
O”. If you bypass the open zone, a “B” will replace the “O”.
4. To unbypass a zone, enter the two-digit number of the zone(s) to be bypassed (01-34). You can
also use the
keys to find the zone, and then press
to select the zone. The “B” will
disappear from the display to show that the zone is no longer bypassed.
5. To exit bypassing mode and return to the Ready state, press
Activating All Bypassed Zones
To remove bypass (all zones):
.
.
.
1. Press
2. Press
, then your [access code] (if necessary).
.
3. To exit bypassing mode and return to the Ready state, press
Recalling Bypassed Zones
To recall the last set of bypassed zones:
1. Press
2. Press
, then your [access code] (if necessary).
.
3. To exit bypassing mode and return to the Ready state, press
Bypass Group
A Bypass Group is a selection of zones programmed into the system. If you bypass a group of zones
on a regular basis, you can program them into the Bypass Group, so that you do not have to bypass
each zone individually every time. Only one Bypass Group can be programmed.
NOTE: If a group has already been bypassed before programming a Bypass Group, you will be
unable to recall that group after programming the new group.
To program a Bypass Group:
1. Press
, then your [access code] (if necessary).
2. Enter the two-digit numbers (01-34) of the zones to be included in the Bypass Group or
use the keys to find the zone to be included in the bypass group, then press
to select the zone.
3. To save the selected zone into the group, press
.
4. To exit bypassing mode and return to the Ready state, press
.
NOTE: If an access code is required to enter bypassing, only the Master Code and codes with
Supervisory enabled can set the Bypass Group.
5
To select a Bypass Group when arming the system:
1. Press
2. Press
, then your [access code] (if necessary).
. The next time the system is armed, the zones in this group will be bypassed.
3. To exit bypassing mode and return to the Ready state, press
.
NOTE: A Bypass Group is only recalled if the system is armed/disarmed after programming the by-
pass group.
NOTE: This feature is not to be used in UL Listed installations.
Trouble Conditions
When a trouble condition is detected, the Trouble ( ) indicator will turn on, and the keypad will
beep every 10 seconds. Press the
dition. The Trouble ( ) indicator will flash. Use the
key to silence the beeps. Press
to view the trouble con-
keys to view troubles.
Trouble
Condition
Comments
Action
Service Required
(Press [1] for more
information)
Indicates Low Battery, System Trouble, System Tamper or
RF Jam detected.
Call for service
If the building and/or neighbourhood has lost electrical Check AC
power, the system will continue to operate on battery for
several hours.
Loss of AC Power
connection
Call for service
Telephone Line
Fault
The system has detected that the telephone line is dis-
connected.
Call for service
The system attempted to communicate with the moni-
toring station, but failed. This may be due to Telephone Call for service
Line Fault.
Failure to
Communicate
Sensor (or Zone)
Fault
The system is experiencing difficulties with one or more
Call for service
sensors on the system. Press [5] to display zone(s).
Sensor (or Zone)
Tamper
The system has detected a tamper condition with one or
Call for service
more sensors on the system. Press [6] to display zone(s).
If the system has been equipped with wireless sensors,
one or more has reported a low battery condition. Press [7] Call for service
to display the zone(s). Press [7] again to display WLS keys.
Sensor (or Zone)
Low Battery
If complete power was lost (AC and Battery), the time
and date will need to be re-programmed. Press [*]
Re-program Time &
Date (page 4)
Loss of Time & Date
Alarm Memory
When an alarm occurs, the Alarm Memory Message will be displayed. To view which sensor(s) gener-
ated the alarm, press
For the system keypad use the
Press to exit. To clear the memory, arm and disarm the system.
.
scroll keys to view the sensors in alarm memory.
If an alarm sounded while armed, the system will automatically go to alarm memory when you dis-
arm the system. In this instance, you should approach with caution, as the intruder may still be within
the building/premises.
Door Chime (Entry/Exit Beeps)
To turn the door chime function on or off, press and hold the Chime key for 2 seconds or press
.
6
Access Code Programming
In addition to the Master Access Code, you can program up to 16 additional User Access codes. Press
, plus your Master Access Code, the armed ( ) indicator will turn on.
Enter the 2-digit number to be programmed (i.e. 06 for user access code 6; enter 40 for the Master
Access Code) or use the
keys to find the specific code and press
to select. Enter the new
4 -digit access code. When programming is complete, enter another 2-digit code to program or press
to exit.
The access codes have programmable attributes which allow zone bypassing, duress, supervisor or
one-time use activation.
Access Codes
[ꢀ][5][Master Code] (when disarmed)
The [ꢀ][5] User’s Programming command is used to program additional access codes.
User Codes - User Codes 1-16 are available for the System.
Master Code (Access Code 40) - The Master Code has all of the attributes listed in the Program-
mable Attributes list below except for Duress (2) and One Time Use (8) and is required to program all
Supervisor Code attributes.
Supervisor Codes - These codes are always valid when entering the
User Code Program-
ming section. However, these codes can only program additional codes which have equal or lesser
attributes. Once programmed, the Supervisor Codes receive the Master Code’s attributes. These
attributes are changeable. Any User Code can be made a supervisor code by enabling User Code
Attribute 1 (please see below for details).
Duress Codes - Duress codes are standard User Codes that will transmit the Duress Reporting Code
whenever the code is entered to perform any function on the system. Any User Code can be made a
Duress Code by enabling User Code Attribute 2 (please see below for details).
One Time Use Code - This code permits temporary access to the system for a 24 Hr. time
period. During the 24 Hr. period, the temporary user may disarm the system once. There is no
restriction on the number of times the temporary user may arm the system during the time
period.
NOTE: Duress codes are not valid when entering [ꢀ][5], [ꢀ][6] or [ꢀ][8] sections.
NOTE: Access codes cannot be programmed as a duplicate or as a “Code +/- 1”.
User Code Attributes
1. The default attributes of a new code will be the attributes of the code used to enter
whether it is a new code or an existing code being programmed.
2. System Master (Code 40) has Attribute 3 ON by default.
NOTE: These attributes are not changeable.
Inherent Attributes (all codes except installer)
Arm / Disarm - Any Access Code will be valid for arming and disarming the system.
Command Outputs ([ꢀ][7][1] and [ꢀ][7][2]) - If these outputs require Access Code entry, any
Access Code is valid for performing the [ꢀ][7][1-2][Access Code] functions on the system.
Programmable Attributes ([ꢀ][5][Master/Supervisor Code [9][Code])
1
2
3
Supervisor Code
Duress Code
Zone Bypassing Enabled
4-6 For Future Use
7
8
Bell Squawk upon Away Arming/Disarming
One Time Use Code
Zone Bypassing Attribute
This attribute allows the User to manually bypass zones if Bypassing requires an access code.
7
Bell Squawk Attribute
This attribute is used to determine whether an access code should generate an arming/disarming Bell
Squawk upon entry of the code for Away arming. The Wireless Keys with access codes associated
with them may generate Arming/Disarming Bell squawks. If desired, this option may be used with
codes that are manually entered. Please contact your installer to have this programmed.
NOTE: The Master Code cannot use the Bell Squawk attribute, but is required to enable it for other
codes.
NOTE: This feature cannot prevent the Arm/Disarming squawks from being generated if an access
code assigned to a WLS Key is manually entered at a keypad.
Erasing an Access Code
To erase a code, select the code and enter
as the first digit. If
is entered, the system will
delete the code immediately and the user will be returned to select another code.
User Function Commands
First disarm the system then enter
[Master Code]
The
command is used to gain access to the following list of Master functions of the system.
[1] Time and Date
Enter 4 digits for 24 Hour System Time (HH-MM). Valid entries are 00-23 for the hour and 00-59 for
minutes. Enter 6 digits for the Month, Day and Year (MM-DD-YY)
[2]-[3] Future Use
[4] System Test
The system’s Bell Output - 4 seconds (2 seconds medium volume, 2 seconds high volume ), Keypad
Lights and Communicator are tested.
[5] Enable DLS / Allow Remote System Service
If enabled, the installer will be able to access Installer Programming remotely using DLS (Downloading
Software). This function provides a window for telephone ring detection by the alarm system. The DLS
window will remain open for 6hrs, during which time the installer will be able to enter DLS an unlimited
number of times. After the 6-hr. window has expired, access to programming via DLS will be unavailable
until the window is re-opened.
[6] User Call-up
If enabled by the Installer, the panel will make 1 attempt to call the downloading computer. The
downloading computer must be waiting for the panel to call before downloading can be performed.
[7] For Future Use
[8] User Walk Test
Allows the user to enter the Walk Test mode. See Walk Test on page 9.
Changing Brightness/Contrast
When this option is selected, the keypad will allow you to scroll through 4 brightness levels and 10
contrast levels.
1. Press
[Master code].
keys to scroll to either Brightness Control or Contrast Control.
to select the setting you want to adjust.
2. Use the
3. Press
4. a) ‘Brightness Control’: There are 4 backlighting levels. Use the
level.
keys to scroll to the desired
b) ‘Contrast Control’: There are 10 different display contrast levels. Use the
to the desired contrast level.
keys to scroll
5. To exit, press
.
Changing the Buzzer Level
When this option is selected, the keypad will allow you to scroll through 21 different buzzer levels. A
level of 00 disables the buzzer.
1. Press
[Master Code].
8
2. Use the
keys to scroll to Buzzer Control.
3. There are 21 different levels, use the
keys to scroll to the desired level.
Viewing the Event Buffer
The event buffer will show you a list of the last 128 events that have occurred on your system.
1. Press
[Master Code].
2. To select Event Buffer viewing, press
.
3. The keypad will display the event number and the time and date. Press
this information and the event details.
to switch between
4. Use the
keys to scroll through the events in the buffer.
5. To exit event buffer viewing, press
.
Testing Your System
NOTE: Inform your Monitoring Station when you begin and end System Testing.
All smoke detectors in this installation must be tested by your smoke detector installer or dealer once
a year to ensure they are functioning correctly. It is the user’s responsibility to test the system weekly
(excluding smoke detectors). Ensure you follow all the steps in the two tests below.
NOTE: Should the system fail to function properly, call your installation company for service im-
mediately.
Sounder and Display Test
This Test activates all display pixels and indicator lights and does a four second check of the sounder.
1. Press
[Master Code]
.
2. The following will occur:
- The system activates the Bell output on medium volume for 2 seconds followed by full volume alarm
for 2 seconds. All display lights and LCD pixels will turn ON.
- The Ready, Armed, Trouble and Power LED’s will flash for the duration of the test
3. To exit the function menu, press
.
Walk Test
Walk Test mode allows you test the operation of each detector in the system. While in Walk Test
mode, the Ready, Armed, and Trouble LED's will flash to indicate that the Walk Test is active. The
Walk Test can be terminated at anytime by re-entering
[Master code]
8
on the keypad.The
system will also automatically terminate the Walk Test on completion, it will annunciate with an audi-
ble warning (5 beeps every 10 seconds), beginning five minutes before the termination of the test.
1. Before testing, ensure that the system is disarmed and the Ready light is on.
2. Press
3. Perform a System Test by following the steps in the previous section.
4. Press [Master code] to initiate the Walk Test
and close all zones to return the system to the Ready state.
8
5. To test the zones, activate each detector in turn (e.g., open each door/window or walk in motion
detector areas).
The System will display the following message when each zone (detector) is activated: “Secure
System Before Arming < >”, “Secure System or Enter Code” or “Secure or Arm System”. Use the
keys to view which zones are open. The message will disappear when the zones are
closed.
Allowing Computer Access To Your System
From time to time, your installer may need to send information to or retrieve information from your
security system. Your installer will do this by having a computer call your system over the telephone
line. You may need to prepare your system to receive this ‘downloading’ call. To do this:
Press
[Master code]
at the keypad. This allows downloading for a limited period of
time. During this time, the system will answer incoming downloading calls.
For more information on this feature, please ask your installer.
9
Reference Sheets
Fill out the following information for future reference and store this guide in a safe place.
System Information
Enabled?
ꢁ [F] FIRE ꢁ [A] AUXILIARY ꢁ [P] PANIC
The Exit Delay Time is _______ seconds.
The Entry Delay Time is _______ seconds.
For Service
Central Station Information
Account#: ___________________ Telephone#: __________________
Installer Information:
Company: ___________________ Telephone#: __________________
If you suspect a false alarm signal has been sent to the central monitoring station,
call the station to avoid an unnecessary response.
Access Codes
Master Code [40]: ________________________
Wireless
Key
Wireless
Key
Code
Access Code
Code
Access Code
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
10
Sensor / Zone Information
Sensor Protected Area
Sensor Type
Sensor Protected Area
Sensor Type
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
11
Guidelines for Locating Smoke Detectors
Research has shown that all hostile fires in homes generate smoke to a greater or lesser extent.
Experiments with typical fires in homes indicate that detectable quantities of smoke precede
detectable levels of heat in most cases. For these reasons, smoke alarms should be installed out-
side of each sleeping area and on each storey of the home.
The following information is for general guidance only and it is recommended that local fire
codes and regulations be consulted when locating and installing smoke alarms.
It is recommended that additional smoke alarms beyond those required for minimum protec-
tion be installed. Additional areas that should be protected include: the basement; bedrooms,
especially where smokers sleep; dining rooms; furnace and utility rooms; and any hallways not
protected by the required units.
On smooth ceilings, detectors may be spaced 9.1m (30 feet) apart as a guide. Other spacing
may be required depending on ceiling height, air movement, the presence of joists, uninsulated
ceilings, etc. Consult National Fire Alarm Code NFPA 72, CAN/ULC-S553-M86 or other appro-
priate national standards for installation recommendations.
• Do not locate smoke detectors at the top of peaked or gabled ceilings; the dead air space in
these locations may prevent the unit from detecting smoke.
• Avoid areas with turbulent air flow, such as near doors, fans or windows. Rapid air movement
around the detector may prevent smoke from entering the unit.
• Do not locate detectors in areas of high humidity.
o
o
• Do not locate detectors in areas where the temperature rises above 38 C (100 F) or falls
o
o
below 5 C (41 F).
• Smoke detectors should always be installed in accordance with NFPA 72, the National Fire
Alarm Code. Smoke detectors should always be located in accordance with:
‘Smoke detectors shall be installed outside of each separate sleeping area in the immediate vi-
cinity of the bedrooms and on each additional storey of the family living unit, including base-
ments and excluding crawl spaces and unfinished attics. In new construction, a smoke detector
also shall be installed in each sleeping room’.’Split level arrangement: Smoke detectors are re-
quired where shown. Smoke detectors are optional where a door is not provided between liv-
ing room and recreation room’.
Figure 3a
12
Household Fire Safety Audit
Read this section carefully for important information about fire safety.
Most fires occur in the home. To minimize this danger, we recommend that a household fire
safety audit be conducted and a fire escape plan be developed.
1. Are all electrical appliances and outlets in a safe condition? Check for frayed cords, overloaded
lighting circuits, etc. If you are uncertain about the condition of your electrical appliances or
household service, have a professional evaluate these units.
2. Are all flammable liquids stored safely in closed containers in a well-ventilated cool area? Clean-
ing with flammable liquids should be avoided.
3. Are fire-hazardous materials (matches) well out of reach of children?
4. Are furnaces and wood-burning appliances properly installed, clean and in good working order?
Have a professional evaluate these appliances.
Fire Escape Planning
There is often very little time between the detection of a fire and the time it becomes deadly. It is thus
very important that a family escape plan be developed and rehearsed.
1. Every family member should participate in developing the escape plan.
2. Study the possible escape routes from each location within the house. Since many fires occur at
night, special attention should be given to the escape routes from sleeping quarters.
3. Escape from a bedroom must be possible without opening the interior door.
Consider the following when making your escape plans:
• Make sure that all border doors and windows are easily opened. Ensure that they are not painted
shut, and that their locking mechanisms operate smoothly.
• If opening or using the exit is too difficult for children, the elderly or handicapped, plans for res-
cue should be developed. This includes making sure that those who are to perform the rescue
can promptly hear the fire warning signal.
• If the exit is above the ground level, an approved fire ladder or rope should be provided as well as
training in its use.
• Exits on the ground level should be kept clear. Be sure to remove snow from exterior patio doors
in winter; outdoor furniture or equipment should not block exits.
• Each person should know of a predetermined assembly point where everyone can be accounted
for (e.g., across the street or at a neighbor’s house). Once everyone is out of the building, call the
Fire Department.
• A good plan emphasizes quick escape. Do not investigate or attempt to fight the fire, and do not
gather belongings or pets as this wastes valuable time. Once outside, do not re-enter the house.
Wait for the fire department.
• Write the fire escape plan down and rehearse it frequently so that should an emergency arise,
everyone will know what to do. Revise the plan as conditions change, such as the number of
people in the home, or if there are changes to the building’s construction.
• Make sure your fire warning system is operational by conducting weekly tests. If you are unsure
about system operation, contact your installing dealer.
• We recommend that you contact your local fire department and request further information on
fire safety and escape planning. If available, have your local fire prevention officer conduct an in-
house fire safety inspection.
13
14
NOTES:
WARNING Please Read Carefully
Note to Installers
■ Motion Detectors
This warning contains vital information. As the only individual in contact
with system users, it is your responsibility to bring each item in this warn-
ing to the attention of the users of this system.
Motion detectors can only detect motion within the designated areas as
shown in their respective installation instructions. They cannot discrimi-
nate between intruders and intended occupants. Motion detectors do not
provide volumetric area protection. They have multiple beams of detec-
tion and motion can only be detected in unobstructed areas covered by
these beams. They cannot detect motion which occurs behind walls, ceil-
ings, floor, closed doors, glass partitions, glass doors or windows. Any
type of tampering whether intentional or unintentional such as masking,
painting, or spraying of any material on the lenses, mirrors, windows or
any other part of the detection system will impair its proper operation.
Passive infrared motion detectors operate by sensing changes in tempera-
ture. However their effectiveness can be reduced when the ambient tem-
perature rises near or above body temperature or if there are intentional or
unintentional sources of heat in or near the detection area. Some of these
heat sources could be heaters, radiators, stoves, barbecues, fireplaces, sun-
light, steam vents, lighting and so on.
System Failures
This system has been carefully designed to be as effective as possible.
There are circumstances, however, involving fire, burglary, or other types
of emergencies where it may not provide protection. Any alarm system of
any type may be compromised deliberately or may fail to operate as
expected for a variety of reasons. Some but not all of these reasons may
be:
■ Inadequate Installation
A security system must be installed properly in order to provide adequate
protection. Every installation should be evaluated by a security profes-
sional to ensure that all access points and areas are covered. Locks and
latches on windows and doors must be secure and operate as intended.
Windows, doors, walls, ceilings and other building materials must be of
sufficient strength and construction to provide the level of protection
expected. A reevaluation must be done during and after any construction
activity. An evaluation by the fire and/or police department is highly rec-
ommended if this service is available.
■ Warning Devices
Warning devices such as sirens, bells, horns, or strobes may not warn peo-
ple or waken someone sleeping if there is an intervening wall or door. If
warning devices are located on a different level of the residence or
premise, then it is less likely that the occupants will be alerted or awak-
ened. Audible warning devices may be interfered with by other noise
sources such as stereos, radios, televisions, air conditioners or other appli-
ances, or passing traffic. Audible warning devices, however loud, may not
be heard by a hearing-impaired person.
■ Criminal Knowledge
This system contains security features which were known to be effective
at the time of manufacture. It is possible for persons with criminal intent
to develop techniques which reduce the effectiveness of these features. It
is important that a security system be reviewed periodically to ensure that
its features remain effective and that it be updated or replaced if it is found
that it does not provide the protection expected.
■ Telephone Lines
If telephone lines are used to transmit alarms, they may be out of service
or busy for certain periods of time. Also an intruder may cut the telephone
line or defeat its operation by more sophisticated means which may be
difficult to detect.
■ Access by Intruders
Intruders may enter through an unprotected access point, circumvent a
sensing device, evade detection by moving through an area of insufficient
coverage, disconnect a warning device, or interfere with or prevent the
proper operation of the system.
■ Insufficient Time
There may be circumstances when the system will operate as intended,
yet the occupants will not be protected from the emergency due to their
inability to respond to the warnings in a timely manner. If the system is
monitored, the response may not occur in time to protect the occupants or
their belongings.
■ Power Failure
Control units, intrusion detectors, smoke detectors and many other secu-
rity devices require an adequate power supply for proper operation. If a
device operates from batteries, it is possible for the batteries to fail. Even
if the batteries have not failed, they must be charged, in good condition
and installed correctly. If a device operates only by AC power, any inter-
ruption, however brief, will render that device inoperative while it does
not have power. Power interruptions of any length are often accompanied
by voltage fluctuations which may damage electronic equipment such as a
security system. After a power interruption has occurred, immediately
conduct a complete system test to ensure that the system operates as
intended.
■ Component Failure
Although every effort has been made to make this system as reliable as
possible, the system may fail to function as intended due to the failure of a
component.
■ Inadequate Testing
Most problems that would prevent an alarm system from operating as
intended can be found by regular testing and maintenance. The complete
system should be tested weekly and immediately after a break-in, an
attempted break-in, a fire, a storm, an earthquake, an accident, or any kind
of construction activity inside or outside the premises. The testing should
include all sensing devices, keypads, consoles, alarm indicating devices
and any other operational devices that are part of the system.
■ Security and Insurance
■ Failure of Replaceable Batteries
This system’s wireless transmitters have been designed to provide several
years of battery life under normal conditions. The expected battery life is
a function of the device environment, usage and type. Ambient conditions
such as high humidity, high or low temperatures, or large temperature
fluctuations may reduce the expected battery life. While each transmitting
device has a low battery monitor which identifies when the batteries need
to be replaced, this monitor may fail to operate as expected. Regular test-
ing and maintenance will keep the system in good operating condition.
■ Compromise of Radio Frequency (Wireless) Devices
Signals may not reach the receiver under all circumstances which could
include metal objects placed on or near the radio path or deliberate jam-
ming or other inadvertent radio signal interference.
Regardless of its capabilities, an alarm system is not a substitute for prop-
erty or life insurance. An alarm system also is not a substitute for property
owners, renters, or other occupants to act prudently to prevent or mini-
mize the harmful effects of an emergency situation.
■ System Users
A user may not be able to operate a panic or emergency switch possibly
due to permanent or temporary physical disability, inability to reach the
device in time, or unfamiliarity with the correct operation. It is important
that all system users be trained in the correct operation of the alarm sys-
tem and that they know how to respond when the system indicates an
alarm.
■ Smoke Detectors
Smoke detectors that are a part of this system may not properly alert occu-
pants of a fire for a number of reasons, some of which follow. The smoke
detectors may have been improperly installed or positioned. Smoke may
not be able to reach the smoke detectors, such as when the fire is in a
chimney, walls or roofs, or on the other side of closed doors. Smoke
detectors may not detect smoke from fires on another level of the resi-
dence or building.
Every fire is different in the amount of smoke produced and the rate of
burning. Smoke detectors cannot sense all types of fires equally well.
Smoke detectors may not provide timely warning of fires caused by care-
lessness or safety hazards such as smoking in bed, violent explosions,
escaping gas, improper storage of flammable materials, overloaded elec-
trical circuits, children playing with matches or arson.
Even if the smoke detector operates as intended, there may be circum-
stances when there is insufficient warning to allow all occupants to escape
in time to avoid injury or death.
Release Date: Jan 24/2008
©2007 Digital Security Controls
Toronto, Canada
Printed in Canada
•
29007459R001
|