Instruction Manual
Projection Alarm Clock
model 13020 / 13026
180º
CONTENTS
Placement Guidelines ............. 8
Using the Alarm Clock............ 9
USB Charging........................ 9
Using the Projector................10
Backlight Settings..................10
Troubleshooting ....................11
Care & Maintenance.............12
Specifications........................13
FCC Information ...................13
Customer Support.................14
Warranty..............................14
Unpacking Instructions ........... 2
Package Contents .................. 2
Product Registration ............... 2
Features & Benefits: Sensor..... 2
Features & Benefits: Alarm...... 3
Setup .................................... 5
Sensor Setup ......................... 5
Alarm Setup .......................... 6
Setup Preferences .................. 7
Intelli-Time Clock.................... 7
Questions? Contact Customer Support at
(877) 221-1252 or visit www.AcuRite.com.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Features & Benefits
6 7
13
10
21
14 15 16 17
180º
CHARGE
USB DEVICE
DC 5 v
8 9
11 12
22
23 19
20
18
FRONT OF ALARM
6. Projector Power On/Off
7. Flip Projection 180
C/ F Switch
15. ˚ ˚
Select degrees Celsius or degrees
Fahrenheit temperature units.
˚
for versatile viewing angles.
16. Zone Button
Set time zone preference.
8. Projection Information
Toggle between time, indoor
17. RESET Button
temperature or outdoor temperature
Full reset to factory defaults.
9. Projection Color
18. Projector Focus
Toggle between red or amber.
Adjust the size and focus of the
projected image.
10. UP, SET & DOWN Buttons
for setup preferences.
19. DC 5v Power Input
11. Alarm Setup
20. USB Charging
for compatible smartphones.
12. Alarm On/Off Button
13. Snooze Button
21. + Brightness Button
Increase display brightness.
22. — Brightness Button
BACK OF ALARM
Decrease display brightness.
14. A-B-C Switch
23. Battery Compartment
ID code that must match sensor’s
A-B-C switch to ensure units
synchronize.
24. Battery Compartment Cover
(not shown)
3
Features & Benefits
2
1
3
4
5
6
7
8
®
1. Current Indoor Temperature
Arrow icon indicates direction
temperature is trending.
4. Intelli-Time Date
Pre-programmed to the correct date.
5. Moon Phase
2. Current Outdoor Temperature
Arrow icon indicates direction
temperature is trending.
6. Alarm On/Off
7. Alarm Set Time
®
8. Alarm Days Active
Indicates daily alarm or
weekday-only alarm setup.
3. Intelli-Time Clock
Pre-programmed to the correct
time and automatically updates for
Daylight Saving Time.
4
SETUP
Sensor Setup
conditions. Cold temperatures can
cause alkaline batteries to function
improperly. Use lithium batteries in
the sensor for temperatures below
-4ºF / -20ºC.
Set the A-B-C Switch
1
The A-B-C switch is located inside
the battery compartment. It can
be set to A, B or C. However,
you must select the same letter
choices for both the sensor and the
display unit in order for the units to
synchronize.
1. Slide off the battery
compartment cover. Take note
of the A-B-C switch setting inside
the battery compartment for
display unit setup.
Install or Replace Batteries
2
AcuRite recommends high quality
alkaline or lithium batteries for the
best product performance. Heavy
duty or rechargeable batteries are
not recommended.
2. Insert 2 x AA batteries into
the battery compartment, as
shown. Follow the polarity
(+/-) diagram in the battery
compartment.
The sensor requires lithium
batteries in low temperature
3. Replace the battery cover.
A-B-C Switch
1
set to match
display unit
A B C
Install Batteries
2 AA batteries
2
5
Alarm Clock Setup
Set the A-B-C Switch
Install or Replace Backup
Batteries
1
3
Locate the A-B-C switch inside
the battery compartment. Set
the A-B-C switch to A, B or C.
You must select the same letter
choices for both the display unit
and the sensor in order for the
units to synchronize.
1. Remove the battery
compartment cover.
2. Insert 3 x AA alkaline
batteries into the battery
compartment, as shown.
Follow the polarity
(+/-) diagram in the battery
compartment.
2
1
Plug in Power Adapter
For the best performance, plug
in the power adapter as the main
power source for this product.
3. Replace the battery cover.
A-B-C Switch
set to match
sensor
A B C
Install
3
Batteries
Plug in Power
Adapter
2
3 AA alkaline
batteries
CHARGE
USB DEVICE
DC 5 v
IMPORTANT: Batteries are a backup power source to preserve records in the event of a
power outage. Power adapter recommended as the primary power source to enjoy the full
functionality of the product.
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE
WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be
used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used
batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire,
as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge
non-rechargeable batteries. DO NOT short-circuit the supply terminals.
6
®
Intelli-Time Clock
Intelli-Time clock and calendar are pre-programmed to the correct time and
date, and update automatically for Daylight Saving Time. All you need to do is
select your time zone using the “ZONE” button.
Set the Time, Date & Language
Press and hold the “ ” button, located on the right side of the display, to
enter SET MODE. Once in set mode, the preference you are currently setting
will blink on the display.
To adjust the currently selected (flashing) item, press and release the “ ” or
“
“ buttons (press and HOLD to fast adjust).
To save your adjustments, press and release the “ ” button to adjust the next
preference. The preference set order is as follows:
LANGUAGE (English or French)
TIME ZONE (PST MST CST EST AST HAST AKST)
AUTO DST (Automatically adjust time -/+ on DST dates)
CLOCK HOUR
CLOCK MINUTE
CALENDAR MONTH
CALENDAR DATE
CALENDAR YEAR
You will automatically exit SET MODE if no buttons are pressed for 5 seconds.
Enter setup mode at any time by pressing the “ ” button.
Manual Clock Quick-Adjust
Self-timed clocks may drift by a few minutes over time. You can adjust the time
using the “Quick Adjust” feature.
To access “Quick Adjust” mode, press AND HOLD the “ ” OR “ ” buttons
for at least 8 seconds. The minutes will flash to indicate they can be adjusted.
Press the “ ” or “ ” buttons to adjust the minutes. After 3 seconds of
inactivity, any adjustments will be saved and the clock will return to normal
operation.
7
Placement for Maximum Accuracy
AcuRite sensors are sensitive to surrounding environmental conditions. Proper
placement of both the display unit and outdoor sensor are critical to the
accuracy and performance of this product.
Alarm Clock Placement
Place alarm clock in a dry area free of dirt and dust. To help ensure
an accurate indoor temperature measurement, be sure to place the
display away from heat sources or vents.
Outdoor Sensor Placement
Sensor must be placed outside to observe outdoor conditions.
Sensor is water resistant and is designed for general outdoor use,
however, to extend its life place the sensor in an area protected
from direct weather elements.
Hang the sensor using the integrated hang holes or hanger, or by
using string (not included) to hang it from a suitable location, like a
well covered tree branch. The best location is 4 to 8 feet above the
ground with permanent shade and plenty of fresh air to circulate
around the sensor.
Important Placement Guidelines
• To ensure accurate temperature measurement, place units out of direct
sunlight and away from any heat sources or vents.
• Display unit and outdoor sensor must be within 330 ft (100 m) of each other.
• To maximize wireless range, place units away from large metallic items, thick
walls, metal surfaces, or other objects that may limit wireless communication.
• To prevent wireless interference, place both units at least 3 ft (.9 m) away
from electronic devices (TV, computer, microwave, radio, etc.).
AT
LEAST
TV
3
(.91 m)
APART
(330 feet maximum)
(100 meters)
Setup is Complete
The sensor will now synchronize with the alarm clock. It may take a few
minutes for synchronization to complete.
8
OPERATION
Using the Alarm Clock
Set Alarm Time
Press and release the “
” button to enter ALARM SET MODE.
To adjust the currently selected (flashing) item, press and release the “ ” or
“
“ buttons (press and HOLD to fast adjust).
To save your adjustments, press and release the “
preference. The preference set order is as follows:
” button to adjust the next
ALARM CLOCK HOUR
ALARM CLOCK MINUTE
ALARM EVERY DAY or WEEKDAY ONLY SELECTION
You will automatically exit ALARM SET MODE if no buttons are pressed for 5
seconds. Enter setup mode at any time by pressing the “
” button.
Momentary Backlight
During power adapter use, press the Snooze button for momentary backlight
at 100% brightness. During battery-powered use, press any button for
momentary backlight.
Moon Phase
Track the phases of the moon, conveyed through simple lunar phase icons.
NEW
WAXING
CRESCENT
1ST
QUARTER
WAXING
GIBBOUS
FULL
WANING
GIBBOUS
3RD
QUARTER
WANING
CRESCENT
USB Charging
Charge your mobile device by plugging your device’s
USB power cord (not included) into the USB charging
port on the back of the alarm clock.
CHARGE
USB DEVICE
DC 4.5
v
USB charging is only available during power adapter
use; USB charging is not active when operating on
battery-power only.
Note: Follow the manufacturer’s instructions for your mobile
device(s) to determine compatibility with the USB charging
feature on this product. Some devices may not support USB
charging or may require a higher power rating than this product provides.
Observe the charging status on your device. Ensure your device is working
properly before attempting to charge.
9
Using The Projector
The projector can be rotated to project the time, indoor temperature, or
outdoor temperature on a wall or on the ceiling.
Press the projector power button “ ” to turn the projector ON/OFF.
Press the “
or wall.
” button to flip the projection image 180º for use on a ceiling
Press the “ “ button, located on the left side of the display, to select the
information you want to be projected:
CURRENT TIME
INDOOR TEMPERATURE (
)
OUTDOOR TEMPERATURE ( )
Press the color selection button (
projection.
) to choose between a RED or AMBER
If the projected information is hard to read or blurry, use the “FOCUS” dial on
the back of the projector to make the projected image clearer.
NOTES:
• Do not stare into the projector lens directly!
• Do not touch the projector lens.
• Some rough surfaces will not display the projection clearly.
Display Backlight
Display backlight has 6 brightness levels: 100% (default), 70%, 50%, 30%,
10% and 5%. The backlight will be ON 100% intensity by default, you may
adjust the backlight using the dimmer control buttons located on the back of
the unit.
BATTERY POWER NOTE: The display unit is intended to be plugged in during
use with included AC power adaptor; batteries are optional for maintaining
settings in case of a power outage. Please note that to conserve backup
battery power, the projector and display illumination only activate momentarily
for 10 seconds at a time when the unit is powered by batteries alone. The
display dimmer option is only available when the unit is plugged in.
10
Troubleshooting
If the wireless signal indicator shows no bars:
• Relocate the display unit and/or the outdoor sensor.
The units must be within 330 ft (100 m) of each other.
• Make sure both units are placed at least 3 feet (.9
m) away from electronics that may interfere with the
wireless communication (such as TVs, microwaves,
computers, etc).
No outdoor sensor
reception
no bars
• Use standard alkaline batteries (or lithium batteries in
sensor when temperature is below -4ºF/-20ºC). Do not
use heavy duty or rechargeable batteries. NOTE: It
may take up to 20 minutes for display unit and sensor
to synchronize after batteries are replaced.
• Verify power adapter is plugged in.
• Increase brightness using +/– buttons, located on the
back of the clock.
• The optimum viewing angle for this product is from
slightly above it.
Alarm clock display
seems dark or hard to
read
• Check that the batteries are installed correctly.
Batteries may need to be replaced.
• Reset the display by pressing the reset button, located
on the back of the display unit. Time and date will
need to be entered after a reset.
Alarm clock screen not
working
• Make sure both the display unit and sensor are
placed out of direct sunlight and away from any heat
sources or vents (see page 8).
Inaccurate
temperature
Flashing of the outdoor temperature is generally an
indication of wireless interference.
1. Bring both the sensor and display unit indoors and
remove at least one battery from each.
2. Make sure the A-B-C switch on both units match.
3. Reinstall the battery in the outdoor sensor.
4. Reinstall the battery in the display unit.
Outdoor
temperature
is flashing or
showing dashes
5. Let the units sit within a couple feet of each other
for about 20 minutes to gain a strong connection.
If your AcuRite product does not operate properly after trying
(877) 221-1252 for assistance.
11
Care & Maintenance
Display Unit Care
Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep
away from dust, dirt and moisture. Clean ventilation ports regularly with a
gentle puff of air.
Outdoor Sensor Care
Clean with a soft damp cloth. Do not use caustic cleaners or abrasives.
Replace Intelli-Time Clock Battery
Intelli-Time technology is
powered by a pre-installed
CR2032
3V
coin-cell battery that stores
the time and date settings.
The battery has a shelf life of
several years. To replace the
Intelli-Time battery:
1. Locate the coin cell battery
compartment door on the
back of the display unit.
Unscrew and remove the
compartment cover.
2. Insert 1 x CR2032 coin cell battery into the battery compartment, as shown.
Install battery with “+” positive terminal facing OUT.
3. Screw in the battery cover.
12
Specifications
Outdoor: -40ºF to 158ºF; -40ºC to 70ºC
Indoor: 32ºF to 99ºF; 0ºC to 37ºC
330 ft / 100 m depending on home construction materials
433 MHz
TEMPERATURE RANGE
WIRELESS RANGE
OPERATING FREQUENCY
POWER
Display: 5v power adapter
3 x AA alkaline batteries (optional)
Sensor: 2 x AA alkaline or lithium batteries
Outdoor data: 16 second updates
Indoor data: 60 second updates
DATA REPORTING
FCC Information
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
1- This device may NOT cause harmful interference, and
2- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, There is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
Such modifications could void the user authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.
13
Customer Support
AcuRite customer support is committed to providing you with best-in-
class service. For assistance, please have the model number of this
product available and contact us in any of the following ways:
(877) 221-1252
24/7 support at www.AcuRite.com
► Installation Videos
► Instruction Manuals
► Replacement Parts
► Register your Product
► Support User Forum
► Submit Feedback & Ideas
PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE
IMPORTANT
PRODUCT REGISTRATION
Register online
to receive 1 year
warranty protection
Register a Product
►
www.AcuRite.com
Limited One Year Warranty
warranty will not be breached, and Chaney will give no credit
for products it manufactures which have received normal wear
and tear, been damaged (including by acts of nature), tampered,
abused, improperly installed, damaged in shipping, or repaired
or altered by others than authorized representatives of Chaney.
At AcuRite, we proudly uphold our commitment
to quality technology. Chaney Instrument Co.
warrants that all products it manufactures to
be of good material and workmanship, and to
be free of defects when properly installed and
operated for a period of one year from the date
of purchase.
The above-described warranty is expressly in lieu of all other
warranties, express or implied, and all other warranties are
hereby expressly disclaimed, including without limitation the
implied warranty of merchantability and the implied warranty
of fitness for a particular purpose. Chaney expressly disclaims
all liability for special, consequential or incidental damages,
whether arising in tort or by contract from any breach of this
warranty. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation
or exclusion may not apply to you. Chaney further disclaims all
liability from personal injury relating to its products to the extent
permitted by law. By acceptance of any of Chaney’s products,
the purchaser assumes all liability for the consequences arising
from their use or misuse. No person, firm or corporation is
authorized to assume for Chaney any other liability in connection
with the sale of its products. Furthermore, no person, firm or
corporation is authorized to modify or waive the terms of this
paragraph, and the preceding paragraph, unless done in writing
and signed by a duly authorized agent of Chaney. This warranty
gives you specific legal rights, and you may also have other
rights which vary from state to state.
We recommend that you visit us at
your product. However, product registration
does not eliminate the need to retain your
original proof of purchase in order to obtain
warranty benefits.
Chaney Instrument Co. warrants that all products it manufactures
to be of good material and workmanship, and to be free of
defects when properly installed and operated for a period of
one year from the date of purchase. Remedy for breach of this
warranty is limited to repair or replacement of the defective
item(s). Any product which, under normal use and service, is
proven to breach the warranty contained herein within ONE
YEAR from date of sale will, upon examination by Chaney,
and at its sole option, be repaired or replaced by Chaney.
Transportation costs and charges for returned goods shall
be paid for by the purchaser. Chaney hereby disclaims all
responsibility for such transportation costs and charges. This
For in-warranty claims: Chaney Instrument Co.
965 Wells St., Lake Geneva, WI 53147
14
15
Weather
Stations
Temperature
& Humidity
Weather
Alert Radio
Kitchen
Thermometers
& Timers
Clocks
AcuRite offers an extensive assortment of precision instruments,
designed to provide you with information you can depend on to
Plan your day with confidence™.
www.AcuRite.com
©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of
the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and copy-
rights are the property of their respective owners. AcuRite uses patented technology.
Printed in China
13020 INST 112713
|