Notes on Spare Drives using the Easy RAID Setting (EZ)
When EZ is function is ENABLED, the auto-rebuilding to spare drive is automatic.
T E C H N O L O G I E S
The degraded RAID group will start rebuilding automatically by using the existing
spare drive.
* Spare drive can be either plugged before RAID building or a new drive can be plug
as the spare drive when RAID rebuild is required.
A.
Which port acts as a spare drive?
The last drive will automatically become the spare drive.
For a 3-drive RAID5 with spare:
Drives connected to SATA ports 1~3 belong to the active RAID5 array and
drive connected to port 4 is the spare.
For a 4-drive RAID10 with spare:
Drives connected to SATA ports 1~4 belong to the active RAID10 array and
drive connected to port 5 is the spare.
R
For a 2-drive RAID1 with spare:
Drives connected to SATA ports 1& 4 belong to the active RAID1 array and
drive connected to port 5 is the spare.
B.
When will rebuild action start?
•
When the raid fails and EZ is enabled, the HPM-XA will
automatically rebuild the RAID group using the spare.
•
When the raid fails and EZ is disabled, the HPM-XA will NOT
rebuild the raid group unless you install a good drive to replace the
failed drive.
User Guide
RAIDTower III
(RT3DAHEU3)
v8.1.11
CONTACT US
Technical Support
If you need any assistance to get your unit functioning properly, please have your
product information ready and contact Addonics Technical Support at:
Phone:
Fax:
408-573-8580
408-573-8588
Email:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Default factory DIP Switch setting:
Setting or Modifying the RAID Mode Using the JMicron
HW RAID Manager Utility Program:
SW1 – RAID Setting DIP Switch
1.
For Windows users, install the JMicron HW RAID Manager located on the
SATA Controller CD. In the CD, go to Configuration Utilities > JMB393. This
manager can be use to create and monitor the status of the RAID volume.
BZS – Error buzzer function
EZ – Automatic rebuilding to spare drive (one of the drives on the raid is set as a
spare). If EZ is ENABLED anda drive failure occurs, the spare will
automatically act as a drive replacement and rebuilding will automatically
start.
It is recommended to use the default factory RAID DIP switch setting when
using the JMicron HW RAID Manager.
M2 – RAID mode 2
M1 – RAID mode 1
2.
Modify the RAID mode on the 5-port HPM-XA using DIP switch
M0 – RAID mode 0
SW1
Recommended to be used on operating system without JMicron HW RAID
Manager support like Linux, Mac & Solaris. Windows users can also use the
procedure below.
1
2
3
4
5
BZS EZ M2 M1 M0
1.
2.
3.
Error buzzer function is ENABLED (BZS) when dip switch is in OFF position
Auto-rebuilding to spare drive is DISABLED (EZ)
Individual drive mode is ENABLED (M0~M2)
Note: Steps A to D need to be performed each time the raid mode is modified.
a.
Set the DIP switch to factory default setting.
Note: When the default factory RAID setting is used, independent drive configuration
and optical drive are supported only when connecting to controllers with Silicon
Image Sil3124, Sil3132 chip set or controllers that are Port Multiplier (PM)
compatible. Simultaneous DVD writing was tested using the Nero Burning Rom.
SW1
1
2
3
4
5
LED Pin Header
BZS EZ M2 M1 M0
J3
J1
b.
Press the RAID setting button with a ball point pen.
c.
While pressing the RAID setting button turn on the system power
where the HPM is connected. The buzzer will sound while holding the
RAID setting button. Release it after at least 5 seconds for hardware
initialization. A single beep will be heard to indicate initialization is
completed. The above steps act as a reset.
P5 P0 P1 P2 P3 P4
P5 P0 P1 P2 P3 P4
Error LED
Activity LED
J1 – Drive Activity LED
P5 – Activity LED for eSATA host port lights up when it is connected to a
SATA controller card.
d.
Power off the system power.
P0, P1, P2, P3 & P4 - Activity LEDs for port 0, 1, 2, 3, 4 & 5 light up when a drive is
connected and blinks when there’s drive activity.
J3 – Error LED
P5 – error LED for eSATA host port
P0, P1, P2, P3 & P4 - error LED for port 0, 1, 2, 3, 4 & 5
3
4
Technical Support (M-F 8:30am - 6:00pm PST)
Phone: 408-453-6212
SATA Ports
e.
On the DIP switch, change (M0 to M2) setting to the
desired RAID mode using the diagram below.
All settings on the diagram shows
•
•
Error buzzer function is ENABLED
EZ function is DISABLED.
RAID 0 Mode
Clone Mode
Error
and
Buzzer
Alarm
Drive
Activity
LEDs
SW1
SW1
SW1
SW1
SW1
1
2
3
4
5
1
2
3
4
5
Floppy
Power
Connector
BZS EZ M2 M1 M0
BZS EZ M2 M1 M0
RAID 1& RAID 10 Mode
Large Mode
USB 3.0/2.0 Host Port
eSATA Host Port (Port 5)
Dip Switch
RAID Setting Button
1
2
3
4
5
1
2
3
4
5
BZS EZ M2 M1 M0
BZS EZ M2 M1 M0
Dip Switch Settings
Raid Mode
1
2
3
4
5
RAID 3 Mode
Individual Drives Mode
Individual Drive
(Factory Default)
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
ON
ON
OFF
ON
0
SW1
1
2
3
4
5
1
2
3
4
5
1 and 10
3
ON
OFF
OFF
OFF
ON
BZS EZ M2 M1 M0
BZS EZ M2 M1 M0
ON
5
OFF
OFF
ON
RAID 5 Mode
Clone
Large
OFF
ON
SW1
Enable
ERR Buzzer Rebuilding
Function
Auto-
Port Multiplier Mode
1
2
3
4
5
to Spare
Drive
BZS EZ M2 M1 M0
5
2
Technical Support (M-F 8:30am - 6:00pm PST)
Phone: 408-453-6212
|