OPERATING INSTRUCTIONS
INSTRUCCIONES DE MANEJO
MODE D’EMPLOI
MM-VX200
MP3 PLAYER
REPRODUCTOR MP3
ENGLISH
ESPAÑOL
FRANÇAIS
OWNER’S RECORD
For your convenience, record the
model number (you will find it on
the rear of your set) and the serial
number (you will find it in the
cassette holder of your set) in the
space provided below.
Pleasereferthemwhenyoucontact
yourAiwadealerincaseofdifficulty.
Model No.
Serial No.
For assistance and information,
call toll free 1-800-BUY-AIWA.
(United States and Puerto Rico)
8A-HZ1-911-01
000721AYO-O-K
Printed in Korea
CONTENTS
2
Chapter 1
PREPARATION BEFORE USE
Thefollowingaresuppliedwiththisplayer.
Check to be sure all the items are in the
package.
1 SYSTEM REQUIREMENTS . . . . . 3
2 CONTENTS . . . . . . . . . . . . . . . . . 3
3 PRECAUTIONS . . . . . . . . . . . . . . 4
4 INSERTING A BATTERY . . . . . . . 5
5 CONNECTING THE PLAYER TO
YOUR PC . . . . . . . . . . . . . . . . . . . 6
• Player
6
SmartMedia-ID INSTALLATION . . . .
6
• USB cable
SYSTEM REQUIREMENTS
1
The VX200 manager software requires
the following system:
• Remote control
• Stereo headphones
• Windows 98, Windows 98 second
edition*
• Pentium 200 MHz MMX or faster
• 1 available USB Port
• CD-ROM drive supporting digital audio
extraction
• 15MB free hard-disk space (may vary
depending on the size of the MP3 files
you wish to use)
• 32MB RAM
• Full duplex Sound card and speakers
• 16-bit color video card
• Installation CD-ROM
• 32 MB SmartMedia-ID
• Carrying case
*For use only PC systems in which
Microsoft Windows 98 or Windows 98
SecondEditionhasbeenpreinstalledby
the manufacturer.
• Operating instructions, etc.
ENGLISH 3
PRECAUTIONS
3
The following are precautions that you
shouldalwayskeepinmind. Anyviolation
ofoneormoreofthefollowingprecautions
may cause damage and will void the
4 ENGLISH
Battery indicator
INSERTING A BATTERY
4
The battery indicator on the display
changes depending on the remaining
power of the battery.
An alkaline battery is recommended for
use with this player.
→
→
→
→
Empty
1 Open the cover of the battery
compartment.
Full
→
Battery replacement
Replace the battery when
battery indicator lights.
of the
Note on dry cell battery
• Make sure that 0 and 9 marks are
correctly aligned.
• Topreventtheriskofelectrolyteleakage
orexplosions,neverrechargethebattery,
apply heat to it, or take it apart.
• When not using the battery, remove it to
prevent needless battery wear.
• If the liquid leaks out from the battery,
wipe thoroughly to remove.
2 Insert a size AA (LR6) alkaline
battery with the 0 and 9 marks
correctly aligned, then close the
cover.
ENGLISH 5
Connecting an AC adaptor
CONNECTING THE
5
TouseonAChousecurrent, contactyour
nearest Aiwa service personnel and
purchase an AC adaptor Aiwa AC-D302.
Connect the AC adaptor:
1 to the DC 3 V jack of the player
2 to a wall outlet
PLAYER TO YOUR PC
Use the supplied USB cable to connect
this player to your PC, as follows:
Connect the series B connector to the
USB port connector of the player and the
other plug to the USB port connector of
your PC.
AC-D302
DC3V
SmartMedia-ID
INSTALLATION
Series B
connector
6
USB port connector
BeforeinsertingaSmartMedia-ID,besure
to turn off the power of the player and
disconnect the USB plug from the USB
port connector.
Supplied USB cable
Insert the SmartMedia-ID into the slot in
the correct direction as follows.
Series A connector
USB port
If a plug is already connected to the USB
port connector of your PC, disconnect it
before connecting this player.
Do not disconnect the USB plug during
downloading or uploading the files to
prevent the error of your PC.
6 ENGLISH
To eject the SmartMedia-ID
Slide the EJECT switch as follows.
Use for data storage
Withupto64MBmemory,including32MB
in the SmartMedia-ID, you can store not
only MP3 files but also any data files such
as doc, gif, txt, bmp, wav, etc. files, as
long as no file is larger than 32MB.
Supplied label for SmartMedia-ID
contact area
write protect area
index area
You can paste the supplied protecting
label on the write protect area on the
SmartMedia-ID.
Donotpasteanylabelonthecontactarea
on the SmartMedia-ID.
Note
• InserttheSmartMedia-IDcompletelyinto
the slot. If it is not inserted completely,
VX200 Manager will not recognize the
data in the SmartMedia-ID.
• When using a SmartMedia-ID for the
first time, initialize the SmartMedia-ID
using the VX200 Manager software.
• The MP3 files in the SmartMedia-ID
cannot be played back with other player
bythesecurityofcopyrightconsideration.
To use a SmartMedia-ID with other
player, you need to initialize the
SmartMedia-ID (See page 16).
ENGLISH 7
INSTALLING THE VX200
MANAGER SOFTWARE
1
Chapter 2
SOFTWARE INSTALLATION
Before installation, check your system
matching to the system that you need
again (see SYSTEM REQUIREMENTS
in Chapter 1) and quit all application
software in use.
VX200 Manager is communication
software that allows your computer to
shareinformationwiththeplayer. Inorder
for the player to work properly, the VX200
Manager software must be installed
correctly under Windows 98.
1 InserttheinstallationCDintoyour
CD-ROM drive.
2 Double-clickontheCD-ROMdrive
icon to open it.
1 INSTALLING THE VX200
MANAGER SOFTWARE . . . . . . . . 8
2 INSTALLING THE USB
DRIVER . . . . . . . . . . . . . . . . . . . . 10
3 INSTALLING THE WAVE DRIVER
(ADPCM Driver) . . . . . . . . . . . . . 10
4 UNINSTALLING THE VX200
MANAGER SOFTWARE . . . . . . . 11
5 UNINSTALLING THE WAVE
DRIVER (ADPCM Driver) . . . . . . 11
8 ENGLISH
3 Double-click on the VX200
Manager folder to open it.
1In the Welcome! dialog box, click
on the Next button to continue
software installation.
2Ifyouwishtochangethedestination
folder to a folder other than the
default folder shown in the dialog
box, click on the Browse button to
select the folder to which you wish
to copy the VX200 Manager
software files.
Next, click on the Next button to
continue installation.
3You can click on the Back button to
reconfigure the installation
information.Tocontinueinstallation,
click on the Next button to start
copying the necessary files into the
installation folder.
4Wait until files for the VX200
Manager software are copied.
5Now, click on the Finish button.
This completes VX200 Manager
software setup.
4 The setup file for the VX200
Manager software is setup.
Double-click on setup to start
installation of VX200 Manager
software.
6The VX200 will be created on the
/Start/Programs/Vx200 menu on
the Windows menu bar, and a
VX200 icon will be created on your
Windows desktop.
7You can start VX200 Manager by
either clicking on the VX200 icon or
clicking on the Vx200 in the Start
menu.
ENGLISH 9
1 InserttheinstallationCDintoyour
CD-ROM drive.
INSTALLING THE USB
DRIVER
2
2 Double-clickontheCD-ROMdrive
icon to open it.
If the USB driver is not installed into your
PC, youcannotdownloadtheMP3filesto
the player.
3 Double-click on the ADPCM
Drivers folder to open it.
To install the USB driver, connect the
player with the supplied USB cable and
insert the supplied CD-ROM into the CD-
ROM drive of your PC.
4 Double-click on ADPCM Driver to
start installation.
1In the Welcome! dialog box, click
on the Next button to continue
software installation.
1 Click “Next” on the “Add New
Hardware Wizard.”
2Ifyouwishtochangethedestination
folder to a folder other than the
default folder shown in the dialog
box, click on the Browse button to
select the folder to which you wish
to copy the ADPCM Driver files.
Now, click on the Next button to
continue installation.
3You can click on the Back button to
reconfigure the installation
information.Tocontinueinstallation,
click on the Next button to start
copying the necessary files into the
installation folder.
4Waituntilthenecessaryfilesforthe
ADPCM Driver have been copied.
5Now, click on the Finish button.
This completes ADPCM Driver
setup.
6The Uninstall ADPCM Drivers item
will be created on the /Start/
Programs/ADPCMDriversmenuon
the Windows menu bar.
2 Select “Search for best driver for
your device” clicking the button
of upper side and click “Next”.
3 Check CD-ROM drive and click
“Next”.
4 Click “Next” according to the
message.
5 AfterinstallationoftheUSBdriver
for MM-VX200, click “Finish”.
INSTALLING THE WAVE
DRIVER (ADPCM Driver)
3
You do not need to install this ADPCM
Wave Driver if you have already installed
theVX200Managersoftwareasdescribed
in the above section.
• The ADPCM Driver lets you play WAV
files converted from voice files you have
recorded using built-in microphone of
the player.
• If you wish to send your voice recorded
as WAV files to someone who does not
have an MM-VX200 player, that person
will have to install the ADPCM Wave
Driver as described below.
If you need to install only the ADPCM
Wave Driver, proceed as follows:
10 ENGLISH
UNINSTALLING THE VX200
MANAGER SOFTWARE
4
TouninstalltheVX200Managersoftware,
choose the /Start/Programs/Vx200/
Uninstall item from the Windows menu
bar. This will remove all VX200 files and
the VX200 folder.
UNINSTALLING THE
WAVE DRIVER (ADPCM
Driver)
5
If you wish to uninstall the ADPCM Driver
from your system, choose the /Start/
Programs/ADPCM Drivers/Uninstall
ADPCM Drivers item from the Windows
menu bar. This will automatically remove
the ADPCM Wave Drivers from your PC.
ENGLISH 11
PREPARING MP3 FILES
2
Chapter 3
Before operating VX200 Manager,
prepare your MP3 file on your PC.
On the supplied Installation CD, you can
find RealJukebox Basic (version 1.0) in
the RealJukebox folder. You can convert
youraudioCDdatatoMP3datausingthe
RealJukebox.
After preparing an MP3 file on your PC,
download the MP3 file to the player to
play back the MP3 files with the player
(see Page 15).
SOFTWARE OPERATION
VX200Managerissoftwarethatinteracts
with the player and a PC. MP3 files and
datafilescanbedownloadedtothisplayer.
However, you can upload only data files
or recorded voice files to the PC.
1 OPENING VX200 MANAGER. . . 12
2 PREPARING MP3 FILES . . . . . . 12
3
OPERATING VX200 MANAGER . . 14
Note
• Do not install the RealJukebox Basic
onto a PC in which RealJukebox Plus
has been already installed. The
application will be replaced with
RealJukebox Basic.
• The RealJukebox supplied in the
installation CD-ROM does not have the
function to communicate with MM-
VX200.
OPENING VX200
1
MANAGER
Before you begin, make sure that the
player is properly connected to the USB
Port of your PC and the VX200 Manager
software has been properly installed.
• AIWA Co., Ltd. does not provide
technical support for the RealJukebox
software.
Access the following URL for details on
operation,support,andotherinformation
on RealJukebox.
1 Double-click on the VX200 icon
on the Windows desktop or
choose the /Vx200 from the Start
menu to activate the program.
12 ENGLISH
AfterinstallingtheRealJukeboxsoftware,
change the encoding options as follows.
ENGLISH 13
OPERATING VX200 MANAGER
3
1
2 3 4 5 6 7 8 9 10 11 12
13 14 15 16
17
18
19
20
1 Option button
2 Firmware button
The Option button brings up the Setup
menu that allows you to specify the path
for an MP3 player on your PC. You can
alsoaccesstheSetupdialogboxfromthe
Tools/Option menu.
You need not use this button for usual
operation. This button has a function for
reprogramming the firmware. Aiwa will
provide the updated firmware and the
usage information for this button on the
following URL when it is required.
Click the Browse button and select your
preferred MP3 player, then click OK.
3 About button
Clicking on this button will display the
version of VX200 Manager and its
copyright information.
14 ENGLISH
4 List of File Type box
The default file type argument *.mp3 can
be used to display the MP3 files in the
current folder.
12 Initialize, Download, and
Upload buttons (Flash Memory)
Initialize button
Select the file type argument *.wav to
display WAV files.
Selectthefiletypeargument*.*todisplay
all types of files.
This will initialize the Flash Memory in the
player. All files stored in Flash Memory
will be erased. You may need to initialize
Flash Memory when for some reason the
player is not being recognized by the
VX200 Manager software.
5–9 Cut, Copy, Paste, Delete, and
Rename buttons
Send to VX200 (Download) button
These buttons work the same as those of
Microsoft Windows Explorer. You can
cut, copy, paste, delete, rename or move
the files you select in the display list box
(localdisplaylistbox)ofthePC.However,
folders will not be moved or copied.
TocopyMP3filesanddatafilesfromyour
PC to the player, drag and drop or use the
Send to VX200 (Download) button
.
Using the mouse, just select the files you
wish to download to the player. Then,
drag and drop them into the display list
box of Flash Memory.
If you wish to copy some files to a folder,
select the files and drag and drop them
while holding the Ctrl key pressed.
Note
• VX200 Manager will not allow you to
download the MP3 files more than 3
times.
10 New Folder button
A new folder under the selected folder in
the local display list box will be created.
• The file name of “xxx.mp3” will be
changed
to
“xxx.mpm”
after
downloading.
11 Update button on the local
display list box
If the information in the local display list
box has been changed, click the Update
button to refresh the local display list box.
• You can download the MP3 files only
from the hard disc drive of your PC. For
example, theMP3filesintheCD-Rdrive
cannot be downloaded with the VX200
Manager.
• You cannot download any files during
playback of voice recording.
In this case, stop playback or voice
recording and click the Update button
(section 15 ) to download the files.
Send to PC (Upload) button
You can also copy data files and PCM
(voice recording) files from the player to
the selected folder on your PC. If you use
the Send to PC (Upload) button
to
copy them onto your PC, you must select
one folder as a destination. The MP3 files
storedintheplayercannotbecopiedonto
your PC.
ENGLISH 15
Note
14 Delete button
• VX200 Manager will not allow you to
upload MP3 files from the player to your
PCbecauseofcopyrightconsiderations.
Only data files and voice files can be
uploaded to your PC.
A selected file in either Flash Memory or
SmartMedia-IDwillbehighlightedinblue.
Just click on the Delete button to remove
a file highlighted in blue.
• If the player is turned off during a copy
process on purpose or because of
insufficientbatterypower,thetransferred
datamightbecorrupted.Youmightneed
to initialize the player.
• You cannot upload any files during
playback of voice recording.
In this case, stop playback or voice
recording and click the Update button
(section 15 ) to upload the files.
15 Update button (Flash Memory)
If the information in the display list box
has been changed, click on the Update
buttontorefreshtheFlashmemorydisplay
list box.
Note
You cannot download or upload any files
during playback of voice recording.
In this case, stop playback or voice
recording and click this Update button
to download or upload the files.
Caution
Before you copy a data file or an PCM file
onto your PC, be sure to rename the file.
If a file with the same filename already
existswhenyoucopythefiles,theprevious
copied file will be erased automatically
and the file will be replaced with a new
one.
16 SmartMedia-ID format button
If you use the SmartMedia-ID formatted
by VX200 Manager with a digital camera
orotherplayers,clickthisbuttontoformat.
17 Local Display list box
13 Initialize , Download
and Upload buttons
(SmartMedia-ID)
These buttons operate as described in
section 12.
If you insert a new SmartMedia-ID, you
must initialize the SmartMedia-ID by
clicking on the Initialize button.
,
Thislistboxshowsthefilesstoredonyour
PC, such as the MP3 files and data files
that you want to copy to the player. The
defaultfiletypeargument*.mp3willdisplay
only MP3 files in the current folder. You
may also select the file type argument *.*
to display all files or specify a type of file
to be displayed.
You may also select *.wav to display the
voice files you recorded. Even if you see
the standard wave format files, however,
you can play back only the voice file
recorded with the MM-VX200 player.
Note
• VX200 Manager will not allow you to
download the MP3 files more than 3
times.
• You cannot copy any MP3 files from the
player to your PC.
• The file name of “xxx.mp3” will be
changed
to
“xxx.mpm”
after
downloading.
• The MP3 files in the SmartMedia-ID
cannot be played back with other player
due to SmartMedia-ID.
16 ENGLISH
To select multiple files
MP3 file info
• While holding the Ctrl key on the
keyboard pressed, click on the desired
files. If you click on a highlighted file, the
file will be unselected.
• If you click on a file while holding the
Shift key pressed, the files between the
first click and the release of the mouse
button will be highlighted.
Youcanmodifyfiledescriptions(ID3tags)
for any MP3 files selected in the local
display list box. ID3 tag information can
be changed by selecting the MP3 Info
from the menu. Clicking on the Modify
buttonwillreplacetheID3taginformation
of the selected MP3 file with the ID3 tag
information you have input.
• The total size of the selected files in the
local display list box will be displayed
below the list box.
ClickingontheRemovebuttonwillremove
the ID3 tag information from the selected
MP3 file.
Click on the Modify button to update the
ID3taginformationaftermakingachange.
Otherwise, the information does not
change even if you have input new data.
18 Flash Memory Display list box
TheupperrightlistboxofVX200Manager
is the Flash Memory display list box.
All files in Flash Memory (built-in memory
of the player) will be displayed in this list
box.
Thesizesoftotalandavailablememoryin
theplayeraredisplayedinkilobytesbelow
the list box.
Note
The filename displayed on the display of
the player will be the Title, Artist name
andAlbumtitleiftheyarecontainedinthe
ID3 tag of the MP3 file. If the ID3 tag does
not contain the Title, Artist name and
Album title, only the MP3 filename,
excluding the MP3 extension, will be
displayed on the display.
ENGLISH 17
1 PLAYER OVERVIEW . . . . . . . . . 18
2 DISPLAY OVERVIEW. . . . . . . . . 20
3 PLAYER OPERATION . . . . . . . . 21
Chapter 4
PLAYER OPERATION
This chapter provides an overview of the
display and operation of the player.
PLAYER OVERVIEW
1
Main unit
1MP3 button
Press to enter MP3 mode, in which you
can play MP3 files.
Press repeatedly to display the MP3
song information such as MPEG Type,
Sampling Rate and Bit Rate.
2\ jack
Connect the supplied remote control.
3Display window
5s POWER OFF button
Press to stop playback or recording.
Keep pressed for 1 second to turn off
the power.
6r button
Press to go back to the beginning of
the current track or previous track.
Keep pressed during playback to
search for a desired point.
7A-B button
Press to repeat a certain portion of the
current track.
8USB port connector
Connect the Series B connector of the
supplied USB cable to connect the
player to your PC.
4HOLD switch
Release before use to activate the
buttons. When not in use, set it to the
HOLD position to prevent unintentional
operation.
18 ENGLISH
9VOLUME button
%t button
Press to adjust the volume. The volume
level ranges from 0 to 20.
0VOICE button
Press to enter Voice mode, in which
you can create and play voice files.
Press again to display the sampling
frequency of the voice file for 3
seconds.
Press to skip to the beginning of the
next or succeeding track.
Keep pressed during playback to
search for a desired point.
^PLAY MODE button
Press repeatedly to select the playback
mode.
&DTP button
Press repeatedly to select the preset
!ERASE button
Press to erase the current MP3 or
equalizer.
voice file.
*REC/STOP button
@Built-in microphone
Records your voice messages.
#DC 3 V jack
Connect the AC adaptor Aiwa AC-D302
(not supplied).
$e POWER ON button
Keep pressed for 1 second to turn on
the power.
Press to start recording using the built-
in microphone in Voice mode.
Press again to stop recording.
• You cannot start recording while any
MP3 or voice file is being played.
(Battery compartment
Insert an LR6 (size AA) alkaline
battery.
)SmartMedia-ID slot
Insert your SmartMedia-ID (16MB,
32MB, or 64MB) into this slot.
Press to start playback of an MP3 or
voice file.
Press during playback to pause, and
press again to resume.
Remote control
1VOL control
2Headphone jack
3e button
4s POWER OFF button
5HOLD switch
6DTP button
7t button
8r button
ENGLISH 19
DISPLAY OVERVIEW
2
Display window
12 3 4 5 6 7
@
! 0 9 8
1Battery Indicator
This displays the remaining battery
power.
2HOLD Icon
This indicates that the HOLD switch is
set to the HOLD position.
3Playback mode Icon
This indicates the selected playback
mode.
7Elapsed playback/recording time
This indicates the elapsed time in
minutes and seconds separated by a
colon of the track currently being
played or recorded.
8Remaining recording time
This appears during voice recording.
9Total number of tracks
This indicates the total number of MP3
files or voice files.
(No Icon) Normal
Repeat
Repeat All
Random
Random Repeat All
0Current track number
This indicates the file number of the
current MP3 or voice file.
!Title
The MP3 title or voice file name is
displayed during playback or voice
files. A voice filename will look like
PAGE xx; where xx is a file number
from 0 to 99. If an MP3 file contains the
Title, Artist name and Album title in its
ID3 tag, the Title, Artist name and
Album title will be displayed. If the MP3
file does not contain the Title, Artist
name and Album title, only the MP3
filename excluding the extension
(.MP3) will be displayed.
4Segment Repeat (A-B)
This indicates the specified location (a
portion being repeated) of the currently
playing file.
5Volume Icon
This indicates the volume level on a
scale of 0 to 20.
@Status
6Memory Icon
This box shows information on the
current status of play, pause and
record.
This indicates the remaining available
memory in megabytes.
20 ENGLISH
MP3 playback
PLAYER OPERATION
3
Turning the power on and off
2
3
\
1
DTP
POWER
OFF
HOLD
POWER
ON
POWER
OFF
PLAY
MODE
A-B
4
POWER OFF
DTP
HOLD
POWER OFF
1 Connect the supplied remote
control to the \ jack of the player
and connect the supplied
headphones to the remote
control.
First, releasetheHOLDswitchtoactivate
the buttons of the player.
Press the e POWER ON button to
turn on the player.
The power will turned off automatically
after about 3 minutes from the last
operation (Auto Power Off function). To
turn off the power before the Auto Power
Off function turns off the power, keep the
sPOWER OFF button pressed for 1
second.
2 Press the MP3 button to select
MP3 playback mode.
3 Press the e button to start
playback.
Playback starts from the MP3 file that
you played last time.
4 Adjust the volume.
When operating with the remote control
Press the e button.
The power is turned on, and playback of
MP3 files starts automatically.
After use, press the s POWER OFF
button to stop playback. The power is
turned off automatically.
Press the r or t button to change
the track number.
To stop playback, press the s POWER
OFF button.
ENGLISH 21
To select a preset equalizer
PresstheDTPbuttonrepeatedlytoselect
a desired equalizer mode.
Classic – Normal sound setting
Rock – Optimized sound setting for
Rock music
Note
You can specify a location to be repeated
only in one MP3 file at a time. If the end of
the current track is reached before you
press the A-B button again, repeat
playback is canceled automatically.
Pop
– Optimized sound setting for
Pop music
Voice recording
Jazz
– Optimized sound setting for
Jazz music
1
2
To select other playback modes
PressthePLAYMODEbuttonrepeatedly
toselectaplaybackmodeofthefollowings.
Each time the button is pressed, the
playback mode changes in the following
order.
POWER
OFF
Normal
– Plays all stored MP3 songs
in order, then stops after
the last song.
3
Repeat
– Plays the current song
repeatedly.
Youcanrecordyourvoicemessageinthe
built-in Flash Memory of the player.
Repeat All – Plays all stored MP3 songs
repeatedly.
Random – Plays all stored MP3 songs
in random order.
1 Press the VOICE button to select
voice mode.
2 Orient the built-in microphone to
the sound source.
Random Repeat All
– Plays all stored MP3 songs
inrandomorderrepeatedly.
3 Press the REC/STOP button to
start recording.
To repeat a certain area
Procedure during MP3 playback
To stop recording, press the REC/
STOP button or the s POWER OFF
button.
Eachtimerecordingstopsbypressing
the REC/STOP button or the s
POWER OFF button, the recording
track number increases.
1 Press the A-B button at the
beginning of the phrase to be
repeated.
2 Press the A-B button again at the
end of the phrase to be repeated.
Playback starts between the marked
locations repeatedly. When the end of
thelocationisreached,playbackstarts
againfromthebeginningofthemarked
location automatically.
Note
You cannot record voice messages
directly into the SmartMedia-ID in the
player.
To cancel repeat playback of the
location, press the A-B button during
repeat playback.
22 ENGLISH
To playback a recorded voice
message
Erasing Files
2,3
1
2
3
\
1
POWER
OFF
MP3 or voice files can be erased without
using VX200 Manager.
1 Connect the supplied remote
control to the \ jack of the player
and connect the supplied
headphones to the remote
control.
1 During stop mode, press the r
or t button to select a track to
be erased from an MP3 file or
voice file.
2 Press the ERASE button.
2 Press the VOICE button to select
voice file playback mode.
3 Press the ERASE button again to
erase the current track.
To cancel erasing, press a button other
3 Press the e button to start
playback.
than the ERASE button.
Press the e button to pause, and
press it again to resume playback.
Presstherortbuttontochange
the track number.
To stop playback, press the s POWER
OFF button.
ENGLISH 23
NOTE
FOR USE IN THE U.S.A.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
Thisequipmentgenerates,uses,andcanradiateradiofrequencyenergyand,ifnotinstalledand
usedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Modifications or adjustments to this product, which are not expressly approved by the
manufacturer, may void the user’s right or authority to operate this product.
DECLARATION OF CONFORMITY
AIWA AMERICA INC. declares, in sole responsibility, that the following product referred to
in the declaration conforms to the following standard, tested on the basis of FCC standard
with the Class B device.
Type of product : Portable MP3 Player
Brand Name
Model Name
: AIWA
: MM-VX200
ANSI C63.4 1992
FCC PART 15 SUBPART B
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference; and (2) this device must accept
any interference received, including interference that may cause undesired operation.
AIWA AMERICA INC.
800 Corporate Drive, Mahwah NJ 07430-2048 U.S.A.
Tel: 201-512-3600
Fax: 201-512-3710
For assistance and information,
call toll free 1-800-BUY-AIWA. (United States and Puerto Rico)
8A-HZ1-911-01
000721AYO-O-K
Printed in Korea
|