ELMC-1
Professional Digital Producer
Featuring:
User Guide
and Reference Manual
4/13
IMPORTANT SAFETY PRECAUTIONS
CAUTION
IMPORTANT SAFETY ITEMS FOR
U.S.A. & CANADA MODEL ONLY
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS
(POLARIZED) PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES
CAN BE CAREFULLY INSERTED TO PREVENT BLADE
EXPOSURE
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS Media Controller TO
WATER OR MOISTURE
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE
CAUTION:
1. Handle the power supply cord carefully. Do not
damage or deform; it may cause electric shock
or malfunction when used. Hold plug attach-
ment when removing from wall outlet. Do not
pull on the cord.
THE Media Controller SHOULD NOT BE ADJUSTED
OR REPAIRED BY ANYONE EXCEPT PROPERLY
QUALIFIED SERVICE PERSONNEL.
2. To avoid electric shock, do not open the top
cover when the unit is plugged in. If problems
occur with the unit, call your local American
Audio® dealer.
NOTE:
This unit may cause interference to radio and
television reception.
3. Do not place metal objects or spill liquid inside
the Media Controller. Electric shock or malfunc-
tion
may occur.
Please carefully read and understand the
instructions in this manual thoroughly before
attempting to operate this unit. These instruc-
tions contain important safety information
regarding the use and maintenance of this unit.
Take special care to follow all warning symbols
and labels both on the unit and printed in this
manual. Also, Please keep this manual with the
unit, for future reference.
CAUTION
Do not open -
Risk of electric shock
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER RACK.
THERE ARE NO USER SERVICEABLE PARTS
INSIDE REFER SERVICE TO YOUR
AUTHORIZED American Audio DEALER.
CAUTION: TO PREVENT ELECTRIC SHOCK
DO NOT USE THIS (POLARIZED) PLUG WITH
AN EXTENSION CORD, RECEPTACLE, OR
OTHER TYPE OF ELECTRICAL OUTLET
UNLESS THE WIDE BLADES CAN BE
CAREFULLY INSERTED INTO A MATCHING
WIDE SLOT.
The lightning flash with an arrow triangular
symbol is intended to alert the user to the
presence of non insulated “dangerous volt-
age” within the products enclosure, and
may be of sufficient magnitude to constitute
a risk of electric shock.
The exclamation point triangular symbol is
intended to alert the user to the presence
of important operating and maintenance
(servicing) instructions in the user manual
accompanying the Media Controller.
ATTENTION: POUR PREVENIR LES CHOCS
ELECTRIQUES NE PAS UTILISER CETTE
FICHE POLARISEE AVEC UN PROLON-
GATEUR, UNE PRISE DE COURANT OU
UNE AUTRE SORTIE DE COURANT, SAUF
SI LES LAMES PEUVENT ETRE INSEREES A
FOND SANS EN LAISSER AUCUNE PARTIE A
DECOUVERT.
©American Audio®
-
-
ELMC-1 Instruction Manual Page 3
ELECTRICAL SAFETY PRECAUTIONS
ELECTRICAL PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product'senclosurethatmaybeofsufficientmagnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER (OR BACK).
THERE ARE NO USER SERVICEABLE PARTS
INSIDE REFER SERVICE TO YOUR AUTHORIZED
AMERICAN AUDIO® SERVICE TECHNICIAN.
IMPORTANT SAFETY INSTRUCTIONS
OBJECT AND LIQUID ENTRY - Never push objects of
READ INSTRUCTIONS — All the safety and operating
GROUNDING OR POLARIZATION
instructions should be read before the product is
operated.
•
Ifthisproductisequippedwithapolarizedalternating
current line plug (a plug having one blade wider than
theother), itwillfitintotheoutlet onlyoneway. This
isasafetyfeature.Ifyouareunabletoinserttheplug
fullyintotheoutlet, tryreversingtheplug. Iftheplug
should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
any kind into this product through openings as they
may touch dangerous voltage points or short-out
parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
RETAIN INSTRUCTIONS — The safety and operating
instructionsshouldberetainedforfuturereference.
HEED WARNINGS — All warnings on the product and
in the operating instructions should be adhered to.
FOLLOW INSTRUCTIONS — All operating and use
instructions should be followed.
SERVICING — Do not attempt to service this product
yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
CLEANING — The product should be cleaned only with
a polishing cloth or a soft dry cloth. Never clean with
furniture wax, benzine, insecticides or other volatile
liquids since they may corrode the cabinet.
•
If this product is equipped with
a
three-wire
DAMAGEREQUIRINGSERVICE - Unplugthisproduct
from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
groundingtypeplug,aplughavingathird(grounding)
pin, itwillonlyfitintoagroundingtypepoweroutlet.
Thisisasafetyfeature.Ifyouareunabletoinsertthe
plug into the outlet, contact your electrician to
replace your obsolete outlet. Do not defeat the
safety purpose of the grounding type plug.
•
•
When the power-supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into
the product.
ATTACHMENTS
—
Do not use attachments not
recommendedbytheproductmanufacturerasthey
may cause hazards.
WATER AND MOISTURE — Do not use this product
near water — for example, near a bathtub, wash
bowl,kitchensink,orlaundrytub;inawetbasement;
or near a swimming pool; and the like.
ACCESSORIES — Do not place this product on an
unstable cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a child or
adult, and serious damage to the product. Use only
•
•
If the product has been exposed to rain or water.
Iftheproductdoesnotoperatenormallybyfollowing
theoperatinginstructions.Adjustonlythosecontrols
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its
normal operation.
POWER-CORD PROTECTION - Power-supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or
against them, paying particular attention to cords at
plugs,conveniencereceptacles,andthepointwhere
they exit from the product.
OUTDOOR ANTENNA GROUNDING — If an outside
antennaorcablesystemisconnectedtotheproduct,
be sure the antenna or cable system is grounded so
astoprovidesomeprotectionagainstvoltagesurges
andbuilt-upstaticcharges.Article810oftheNational
ElectricalCode,ANSI/NFPA70,providesinformation
with regard to proper grounding of the mast and
supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit,
connection to grounding electrodes, and
requirementsforthegroundingelectrode.SeeFigure
A.
LIGHTNING — For added protection for this product
duringalightningstorm,orwhenitisleftunattended
and unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product
due to lightning and power-line surges.
POWER LINES —An outside antenna system should
notbelocatedinthevicinityofoverheadpowerlines
or other electric light or power circuits, or where it
can fall into such power lines or circuits. When
installing an outside antenna system, extreme care
should be taken to keep from touching such power
lines or circuits as contact with them might be fatal.
OVERLOADING — Do not overload wall outlets,
extensioncords,orintegralconveniencereceptacles
as this can result in a risk of fire or electric shock.
•
•
If the product has been dropped or damaged in any
way.
When the product exhibits a distinct change in
performance — this indicates a need for service.
with
a
cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with
the product. Any mounting of the product should
follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the
manufacturer.
REPLACEMENT PARTS -- When replacement parts
arerequired,besuretheservicetechnicianhasused
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorizedsubstitutionsmayresultinfire,electric
shock, or other hazards.
SAFETY CHECK - Upon completion of any service or
repairs to this product, ask the service technician to
performsafetycheckstodeterminethattheproduct
is in proper operating condition.
CART — A product and cart combination should be
moved with care. Quick stops, excessive force, and
uneven surfaces may cause the product and cart
combination to overturn.
WALL OR CEILING MOUNTING — The product should
not be mounted to a wall or ceiling.
HEAT —The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce
heat.
VENTILATION — Slots and openings in the cabinet are
provided for ventilation and to ensure reliable
operation of the product and to protect it from
overheating, and these openings must not be
blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug,
or other similar surface. This product should not be
placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
POWER SOURCES —This product should be operated
only from the type of power source indicated on the
marking label. If you are not sure of the type of
power supply to your home, consult your product
dealer or local power company.
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
LOCATION – The appliance should be installed in a
stable location.
NONUSE PERIODS – The power cord of the appliance
should be unplugged from the outlet when left un-
used for a long period of time.
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
Fig. A
NEC — NATIONAL ELECTRICAL CODE
©American Audio®
-
-
ELMC-1 Instruction Manual Page 4
SAFETY INSTRUCTIONS
I. Read Instructions - All the safety and operat-
ing instructions should be read before the
Player is operated. The safety and operating
instructions should be saved for future
reference.
The serial and model number for this unit is
located on the rear panel. Please write down
the numbers here and retain for future refer-
ence.
2. Heed Warnings - All warnings on the
Player and in the operating instructions
should be adhered to.
Model No.________________________________
Serial No.________________________________
3. Water and Moisture - The player should not
be used near water - for example, near a
bath tub, kitchen sink, laundry tub, in a
wet basement or near a swimming pool, etc.
Purchase Notes:
Date of Purchase__________________________
Dealer Name______________________________
Dealer Address____________________________
_________________________________________
4. Ventilation - The Player should be situated
so that its location or position does not inter-
fere with its proper ventilation. For example,
the player should not be situated on
a bed, sofa, rug, or similar surface that may
block the ventilation openings; or, placed in
a built-in installation, such as a bookcase
or cabinet that may impede the flow of
air through the ventilation openings.
________________________________________
Dealer Phone_____________________________
5. Heat - The player should be situated
away from heat sources such as radiators,
heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
6. Power Sources - The player should be
connected to a power supply only of the
type described in the operating instructions
or as marked on the Player.
7. Servicing - The user should not attempt
to service the Player beyond that
described in the operating instructions. All
other servicing should be referred to quali-
fied service personnel. The Player should be
servicedby qualified service personnel when:
A. The power-supply cord or the plug has
been damaged.
B. Objects have fallen, or liquid has been
spilled into the Player.
C. The Player has been exposed to rain
or water.
D. The Player does not appear to
operate normally or exhibits a marked
change in performance.
©American Audio®
-
-
ELMC-1 Instruction Manual Page 5
UNPACKING
Every ELMC-1 has been thoroughly tested and has been shipped in perfect operating condition.
Carefully check the shipping carton for damage that may have occurred during shipping. If the carton
appears to be damaged, carefully inspect your player for any damage and be sure all equipment
necessary to operate the player has arrived intact. In the event damage has been found or parts are
missing, please contact our toll free customer support number for further instructions. Please do not
return the player to your dealer without first contacting customer support.
INTRODUCTION
Introduction:
Congratulations and thank you for purchasing the American Audio® ELMC-1 Media Controller. This
controller is a representation of American Audio’s continuing commitment to produce the best and
highest quality audio products possible at an affordable price. Please read and understand this manual
completely before attempting to operate your new player. This booklet contains important information
concerning the proper and safe operation of your new controller.
Customer Support:
American Audio® provides a toll free customer support line, to provide set up help and answer any
question should you encounter problems during your initial set up or operation. You may also visit us
through Friday 8:00 a.m. to 4:30 p.m. Pacific Standard Time.
Voice:
Fax:
(800) 322-6337
(323) 582-2610
E-mail:
Caution! There are no user serviceable parts inside this Media Controller. Do not attempt any repairs
yourself, without being instructed to do so by an authorized American Audio service technician. Doing
so will void your manufactures warranty. In the unlikely event your Media Controller may require ser-
vice, please contact American Audio® customer support.
Do not discard the packing carton in the trash. Please recycle when ever possible.
SET-UP PRECAUTIONS
Please be sure to make any connections before plugging the player in to an electrical outlet. All fader
and volume controls should be set to zero or minimum position, before the player is switched on. If the
player has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch
on the player immediately. The arising condensation of water might damage your device. Leave the
device switched off until it has reached room temperature.
Operating Determinations:
• When installing this player, please make sure that the device is not exposed or will not be ex-
posed to extreme heat, moisture or dust!
• Do not operate the player in extremely hot (more than 40°/104°F) or extremely cold (less than
5°C/40°F) surroundings.
• Keep the unit out of direct sunlight and away from heaters.
• Operate the player only after becoming familiar with its' functions. Do not permit operation by
persons not qualified for operating the unit. Most damages are the result of unprofessional operation.
©American Audio®
-
-
ELMC-1 Instruction Manual Page 6
MAIN FEATURES
•
•
•
MIDI Control
Master Volume Control
Crossfader
•
•
•
Seamless Loop (uninterrupted loop playback)
3 Band EQ
Durable Touch Sensitive Jog Wheel
MINIMUM SYSTEM REQUIREMENTS*
PC Requirements:
• Windows XP Sp2 or Windows Vista (32-bit & 64-bit supported)
• PIV 1.2GHz Computer (SSE2 CPU), AMD 64 or Greater
• 1024_768 SVGA Video
• 2 GIG RAM (Vista)
• 40MB Free on the Hard-Drive (Recommended 2000MB)
• DirectX 9.0
Mac Requirements:
• Mac OS X 10.5 PPC/Intel, 10.5.6 Intel, or 10.6 Intel
• 1.86GHz
• 2GB RAM
* System Requirements may differ due to manufacturer software
SET-UP
1. Checking the Contents
Be sure your ELMC-1 was shipped with the following:
1) ELMC-1 Controller
3) USB Cable
2) Operating Instructions (This Booklet)
4) Virtual DJ Software
5) Warranty card
2. Installing the Units
1) Place your unit on a flat surface or secure case.
2) Be sure the player is in a well ventilated area where it will not be exposed to direct
sunlight, high temperatures, or high humidity.
3) Place the unit as far as possible from TVs and tuners, as the unit may cause undesirable
interference.
3. Connections
1) Connect USB Cable
©American Audio®
-
-
ELMC-1 Instruction Manual Page 7
GENERAL FUNCTIONS AND CONTROLS
Figure 1
1
2
3
4 5
12
11
10
9
8
7
6
A. PLAYER - FRONT (FIGURE 1)
1. (-) PITCH BEND BUTTON - The (-) pitch bend function creates a momentary “Slow Down” in the
BPM’s (Beats per minute) while it is playing. This will allow you to match the beats between two play-
ing audio sources. Remember, this is a momentary function. When you remove your finger from the
pitch button, the BPM’s will automatically return to the set pitch value. Holding down this button will
give a maximum of -100% pitch. Use this function to slow to another playing music source. Be sure
to notice that this function is a momentary pitch adjustment, for a more precise adjustment use the
PITCH FADER to match the BPM’s with another playing music source.
(+) PITCH BEND BUTTON - The (+) pitch bend function creates a momentary “BUMP” in the
BPM’s (Beats per minute) while it is playing. This will allow you to match the beats between two play-
ing audio sources. Remember, this is a momentary function. When you remove your finger from this
button, the BPM’s will automatically return to the selected pitch. Holding down this button will give a
maximum of +100% pitch.
Hold SHIFT and the PITCH BUTTONS to adjust the pitch fader. NOTE: This feature has an auto repeat
feature so the slider will move smoothly as if a fader was being move.
2. FX SELECT/SAMPLER SELECT/LOOP ADJUSTMENT -
FX SELECT - This knob is used to set the desired FX. Once the desired effect appears in the
©American Audio®
-
-
ELMC-1 Instruction Manual Page 8
GENERAL FUNCTIONS AND CONTROLS (Cont.)
effect window in Virtual DJ, press the knob to activate the effect. Once an effect is active, this
knob will temporarily control the effect parameter till the effect is deactivated. Press the knob to
deactivate the effect.
SAMPLER SELECT - Holding SHIFT while turning this knob will set the sampler on in the sam-
ple window. Rotate the knob left or right once the the desired effect is found. Start/Stop the
sampler by pressing the knob. If a sample is active, the knob will control the volume temporarily
while the sample is playing.
LOOP ADJUSTMENT - If a loop is active, this knob can control/adjust the loop size till the loop
is exited.
3. MIXER SECTION
CHANNEL GAIN CONTROL - This adjustment is used to adjust the audio source signal input gain
for a channel. Never use the gain control to adjust a channels output volume. Setting the gain level
properly will ensure a clean output signal. An improper gain level adjustment will send a distorted
signal throughout the entire audio line which may damage speakers and amplifiers. To properly set a
channels gain level control:
1. Be sure the MASTER VOLUME CONTROL is set to level 4.
2. Set the GAIN KNOB to level 8.
3. Begin playback on an audio source connected to the channel you are adjusting.
4. Use the Gain Control to adjust an average output volume of +4 dB.
5. Repeat this step for all channels
CHANNEL TREBLE CONTROL - This knob is used to adjust the treble levels of a channel allowing
for a maximum treble gain of +6dB or maximum decrease of -100dB. Turning the knob in a counter-
clockwise direction will decrease the amount of treble applied to a channel signal, turning the knob in
a clockwise direction will increase the amount of treble applied to a channel signal.
CHANNEL MIDRANGE CONTROL - This knob is used to adjust the midrange levels of a channel
allowing for a maximum midrange gain of +6dB or maximum decrease of -100dB. Turning the knob in
a counter-clockwise direction will decrease the amount of midrange applied to a channel signal, turn-
ing the knob in a clockwise direction will increase the amount of midrange applied to a channel signal.
CHANNEL BASS CONTROL - This knob is used to adjust the low frequency levels of a channel
allowing for a maximum bass gain of +6dB or maximum signal decrease of -100dB. Turning the knob
in a counter-clockwise direction will decrease the amount of bass applied to a channel signal, turning
the knob in a clockwise direction will increase the amount of bass applied to a channel signal.
4. MASTER VOLUME CONTROL - This knob is used to control the master output level. To avoid
distorted output try to maintain an average output signal level no greater than +4dB. To avoid speaker
damage that may be caused by excessive volume, be sure this knob is always set to zero (completely
down) before turning the unit on.
5. NAVIGATION BUTTONS - These buttons allow easy navigation of your music library on your soft-
ware.
BROWSE KNOB - Turn this knob to scroll through and select your music tracks in the soft-
ware. To enter a folder or return to the last folder in the software, press the knob.
LOAD BUTTON - Press this button to load the selected track to that deck. Pressing this button
and the SHIFT button will CUE the source to the headphones.
SHIFT BUTTON - Hold this to use secondary commands for certain buttons.
©American Audio®
-
-
ELMC-1 Instruction Manual Page 9
GENERAL FUNCTIONS AND CONTROLS (Cont.)
6. LOOP - This button will set a 4 beat loop and activate loop divide and multiply functions on the
FX select knob.
7. PLAY/PAUSE BUTTON - Press this button to PLAY/PAUSE what ever music source is playing.
8. CUE - Pressing the CUE button during playback immediately pauses playback and returns the
track to the last set cue point. The red CUE LED will glow when the unit is in cue mode. The LED will
also flash every time a new CUE POINT is set. The CUE button can be held down to momentarily
play the track. When you release the CUE button it instantly returns to the CUE POINT. You can also
tap the CUE button to create a BOP EFFECT.
9. SYNC BUTTON - Use this button to set this deck to master and auto sync and the other deck's
tempo to master.
10. VINYL BUTTON - Pushing this button activates SCRATCH mode.
11. CROSSFADER - This fader is used to blend the output signals of channels A and B together.
When the fader is in the full left position (channel A), the output signal of channel A will be controlled
by the master volume level. The same fundamentals will apply for channel B. Sliding the fader from
one position to another will vary the output signals of channels A and B respectively. When the cross-
fader is set in the center position, the output signals of both the channels A and channels B will be
even.
12. JOG WHEEL - This wheel has three functions;
Attention: Make sure that NOTHING is touch or resting on the jog wheels when you power on the
ELMC-1.
A. The wheel works as a pitch bend during Playback. Turning the wheel clockwise can increase the
pitch percentage up to 100%, and turning the wheel in the counter-clockwise direction can de-
crease the pitch percentage down to -100%. The pitch bend will be determined on how long
you turn the jog wheel continuously.
B. The jog wheel also controls the scratch effect, when the scratch effect is active.
C. The jog wheel can also serve as frame search. To use frame search the track must be paused
and the scratch effect must be disabled.
Note: The inside of the wheel is touch sensitive and the outside edge of the wheel is not. Example:
You can scratch by touching the inside or center of the wheel, and pitch bend when you touch the
outside edge of the wheel.
REAR PANEL - GENERAL FUNCTIONS AND CONTROLS
13
REAR PANEL -
13. USB PORT - Connect to your PC for MIDI interface.
©American Audio®
-
-
ELMC-1 Instruction Manual Page 10
COMPUTER CONNECTION
1. CONNECTING THE ELMC-1 TO YOUR PC
Connect the ELMC-1 to your PC by using the USB ports located on the rear of the ELMC-1 and your PC.
Connect the supplied USB cable to the USB port on the rear of the ELMC-1, and the other end connects to the
USB port on your computer. NOTE: Before connecting your ELMC-1 to your computer or laptop, we highly
recommend that you install the provided software. The Virtual DJ version included with this product is
specifically tailored to work with the ELMC-1 with no setup required. The setup of other non-factory
authorized drivers and software is far more complex and in some instances not as reliable.
Simple Output Configuration
Master and Headphone Configuration
sound card is optional
and not included
©American Audio®
-
-
ELMC-1 Instruction Manual Page 11
CLEANING
Due to fog residue, smoke, and dust, cleaning the mixer should be carried out periodically to residue
build up.
1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.
2. Use a cleaner specially designed for electronics to spray in and around the knobs and switch.
This will reduce small particle built up that can effect the proper operation of the mixer.
3. Cleaning should be carried out every 30-60 days to prevent heavy built up.
4. Always be sure to dry all parts completely before plugging the mixer in.
Cleaning frequency depends on the environment in which the mixer operates (i.e. smoke, fog residue,
dust, dew).
©American Audio®
-
-
ELMC-1 Instruction Manual Page 12
WARRANTY
WARRANTY INFORMATION: The ELMC-1 carries a ONE year (365 days) limited warranty. This
warranty covers parts and labor. Please fill out the enclosed warranty card to validate your purchase
and warranty. All returned service items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. If the unit is under warranty, you must provide a copy
of your proof of purchase invoice. Please contact American Audio® customer support at (800) 322-
6337 for a R.A. number. All package not displaying a R.A. number on the outside of the package will
be returned to the shipper.
1-YEAR LIMITED WARRANTY
A. American Audio® hereby warrants, to the original purchaser, American Audio® products to be free
of manufacturing defects in material and workmanship for a period of 1 Year (365 days) from the date
of purchase. This warranty shall be valid only if the product is purchased within the United States of
America, including possessions and territories. It is the owner’s responsibility to establish the date and
place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service, send the product only to the American Audio® factory. All shipping charges
must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms
of this warranty, American Audio® will pay return shipping charges only to a designated point within the
United States. If the entire instrument is sent, it must be shipped in its original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, American Audio®
shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return
thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in
any manner which American Audio® concludes, after inspection, affects the reliability of the product;
if the product has been repaired or serviced by anyone other than the American Audio® factory unless
prior written authorization was issued to purchaser by American Audio®; if the product is damaged
because not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning or peri-
odic check-up. During the period specified above, American Audio® will replace defective parts at its
expense, and will absorb all expenses for warranty service and repair labor by reason of defects in
material or workmanship. The sole responsibility of American Audio® under this warranty shall be lim-
ited to the repair of the product, or replacement thereof, including parts, at the sole discretion of Ameri-
can Audio®. All products covered by this warranty were manufactured after January 1, 1990, and bear
identifying marks to that effect.
E. American Audio® reserves the right to make changes in design and/or improvements upon its prod-
ucts without any obligation to include these changes in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied
with products described above. Except to the extent prohibited by applicable law, all implied warran-
ties made by American Audio® in connection with this product, including warranties of merchantability
or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether
expressed or implied, including warranties of merchantability or fitness, shall apply to this product after
said period has expired. The consumer’s and or Dealer’s sole remedy shall be such repair or replace-
ment as is expressly provided above; and under no circumstances shall American Audio® be liable for
any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product.
G. This warranty is the only written warranty applicable to American Audio® Products and supersedes
all prior warranties and written descriptions of warranty terms and conditions heretofore published.
©American Audio®
-
-
ELMC-1 Instruction Manual Page 13
SPECIFICATIONS
GENERAL
Model: American Audio® ELMC-1 - PC Media Controller
Dimensions:
399(L) x 300(W) x 40(H) mm
15.7"(L) x 12(W) x 1.5"(H)
Place on flat surface or mount in flat case
10.9 Lbs. / 4.93 Kgs
Installation:
Weight:
Power supply:
USB
CHECK THE AMERICAN AUDIO WEBSITE FOR DOWNLOADABLE USER SOFTWARE
UPDATES.
©American Audio®
-
-
ELMC-1 Instruction Manual Page 15
©American Audio® World Headquarters:
6122 S. Eastern Ave., Los Angeles, CA 90040 USA
Tel: 323-582-3322 Fax: 323-582-3311
American DJ Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
|