TOWN SQUARE® 27"
PEDESTAL SINK
FIRECLAY
BARRIER FREE
TOWN SQUARE® 27" PEDESTAL SINK
• American classic design
• Clean straight lines with classic ogee curves
• Rear overflow
• Supplied with mounting kit
• Design-matched to Town Square®
fixture and faucets
• Right Height™ for greater comfort during use
• Made from fireclay
❏ 0780.400 Faucet holes on 4" (102mm) centers
❏ 0780.800 Faucet holes on 8" (203mm) centers
❏ 0780.100 Center hole only
Nominal Dimensions:
27" x 21-1/4" x 36"
(686 x 540 x 914mm)
20-1/4" (514mm)
4"
2-5/8"
(67mm)
4"
FINISHED WALL
(102mm)
(102mm)
Separate Components:
❏ 0780.004 Pedestal top 4" (102mm) centers
❏ 0780.008 Pedestal top 8" (203mm) centers
❏ 0780.001 Center hole only
9-5/8"
(244mm)
5/8"
(16mm)
21-1/4"
(540mm)
1-3/4" DIA.
STD. DRAIN
OUTLET
❏ 0031.000 Pedestal only
Bowl sizes:
15" (381mm) wide
12-1/2 (318mm) front to back
6-1/2" (165mm) deep
PED BASE
OUTLINE
PED TOP
OUTLINE
27"
(686mm)
3-3/4" (95mm)
DRAIN
CHASE
8"
(203mm)
3/8" (10mm) DIA.
SLAB ANCHOR
SCREW HOLES
ON 20-1/4" (514mm)
CTRS
Compliance Certifications -
6"
Meets or Exceeds the Following Specifications:
• ASME A112.19.9M for Non-Vitreous Ceramic Fixtures
• CAN/CSA B45 Series
(152mm)
SUPPLIES AS
REQUIRED
36"
(914mm)
1-1/4" O.D.
WASTE
1-1/4" O.D.
TAILPIECE
24"
*
(610mm)
28"
(711mm)
OPEN
TO
FLOOR
22"
*
(559mm)
To Be Specified:
❏ Color: ❏ White ❏ Bone ❏ Linen
3/8" (10mm) DIA.
BASE ANCHOR
SCREW HOLES
ON 6" (152mm)
CTRS
❏ Silver ❏ Black
❏ Town Square Faucet:
❏ Centerset Lavatory Faucet: 2555.201
❏ Widespread Lavatory Faucet: 2555.801
(shown)
10"
(254mm)
FINISHED
FLOOR
6"
(152mm)
❏ Other Lavatory Faucet*:
❏ Faucet Finish:
❏ Supplies:
NOTES:
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE
*
SUGGESTED.
▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED.
■ FOR REINFORCEMENT ONLY. TAKE ACTUAL DIMENSIONS FROM
FIXTURE.
❏ 1-1/4" Trap:
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.
* See faucet section for additional models available
IMPORTANT: Dimensions of fixtures are nominal and may vary within the
range of tolerances established by ANSI Standard A112.19.9M.
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided pages.
J3
© 2008 AS America Inc.
Revised 2/08
|