XM6
Owner’s Manual
Use and Care
In normal daily use, the TERK XM6 Outdoor Home Antenna is
a rugged, high-performance antenna that does not require any
special attention.
Troubleshooting
When a problem occurs with the installation of the XM6
antenna the receiver will display one of the following error
messages.
ANTENNA
The antenna is not connected properly.
-Check and make sure that all the connections between
the antenna, adapter and receiver are secure.
NO SIGNAL
XM signal is being blocked from reaching the XM antenna.
- Keep in mind that the antenna needs to be in the line
of sight with the XM satellites. The antenna needs to
be located on the outside of your house or building
with an unobstructed view of the open sky.
Other Symptoms
If there are issues with your receiver, please review the
reciever owners manual. Should any problem persist with
your antenna after you have made the above checks, call
Audiovox at the number listed below.
12 Months Limited Warranty
AUDIOVOX ELECTRONICS CORPORATION (the Company) warrants to the original retail
purchaser of this product that should this productor any part there of, under normal use
and conditions, be proven defective in material or workmanship within 12 months from the
date of original purchase, such defect(s) will be repaired or replaced with new or
reconditioned product (at the Company's option) without charge for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be
delivered with proof of warranty coverage (e.g. dated bill of sale), specification of
defect(s), transportation prepaid, to an approved warranty station or the Company at the
address shown below.
This Warranty does not extend to the elimination of externally generated static or noise,
to costs incurred for installation, removal or reinstallation of the product, damage to
speakers, accessories, or vehicle and home electrical systems, malfunction of satellite
transmissions, repeater signal or receiver unit.
This Warranty does not apply to any product or part thereof which, in the opinion of the
Company, has suffered or been damaged through alteration, improper installation,
mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial
number/bar code label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS
WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN
NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY
PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL
BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR
BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 48 MONTHS FROM DATE
OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or representative is
authorized to assume for the Company any liability other than expressed herein in
connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential damage so the above limitations or
exclusions may not apply to you. This Warranty gives you specific legal rights and you
may also have other rights which vary from state to state.
U.S.A. : AUDIOVOX ELECTRONICS CORPORATION, 150 MARCUS BLVD., HAUPPAUGE,
NEW YORK 11788 • 1-800-645-4994 CANADA : CALL 1-800-645-4994
FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA
128-7351
About XM Satellite Radio
For more information about
XM Satellite Radio service,
To activate your XM service
please call 1-888-539-7474
For Customer Service
Visit Our Website At
For customer service and
technical information::1.800.290.6650
Product Information, Photos,
FAQ’s, Owner’s Manuals
XM6
TERK and the TERK logo are registered trademarks of AUDIOVOX Corp.
The XM name and related logos are trademarks of XM Satellite Radio Inc.
Outdoor XM Satellite Radio Home Antenna
Installation
Installation
Now that you have determined where to place the antenna,
you have three different mounting options. Each option is
described below.
We recommend mounting the antenna on a roof as high
up as possible as shown on page 4. The antenna should
not be blocked by an obstruction like trees or a chimney.
Once you have determined your mounting location, place
the mounting bracket on that location on the roof. Take
your drill and pre-drill holes, using a 3/32 drill bit, through
the top two holes on the mounting bracket. Screw in two
of the #10 screws included with this package, through the
mounting bracket into the pre-drilled holes in the roof.
Repeat this step for the bottom two holes. At this point,
move onto the Adjustment section of the owner’s manual
on page 6.
Wall Mount
Mast Mount
or
Please determine where to mount the antenna. Once
the mounting location has been determined, take a
pencil and mark through the bracket, onto the house
wall, the four screw locations. Then set the mounting
bracket down and pre-drill holes in the four locations
you just marked (drill bit size 3/32 is recommended with
#10 screws). Position the mounting bracket over the four
pre-drilled holes and screw in the top two #10 screws,
that are included with this package through the mounting
bracket into the wall of the house. Then screw in the
bottom two. At this point, move onto the Adjustment
section of the owner‘s manual on page 6.
The XM6 can be mounted to most masts. We recommend
mounting the antenna to a mast on the roof or on the mast
of a satellite TV dish. You will need the 2 U-bolts, 2 mount
brackets and 4 nuts for this installation. Once you have
determined where on the mast you wish to mount the
antenna, place the mounting bracket in that location against
the mast. Put one of the U-bolts through the top two holes
on the mounting bracket. Take one of the mount brackets
and insert it through the two ends of the U-bolt on the other
side of the mast. Make sure the inside of the curve of the
mount bracket is towards the mast. Using one hand to hold
the mounting bracket and U-bolt bracket take your other
hand and place one nut on one end of the U-bolt, then turn
the nut four or five complete rotations and then place one
nut on the other end of the U-bolt, turn the nut four or five
complete rotations. Make sure the mounting bracket is in
the desired location and tighten both nuts until the mounting
bracket is secure on the mast. Before mounting the bottom
U-bolt, please refer to the last step on the Cable Installation
section on page 6. Repeat these steps for the second U-bolt.
Once complete, move to the Adjustment section of the
owner’s manual on page 6.
Roof Mount
4
5
Adjustments
Specifications
To make sure the antenna is level please make the
Electrical Specifications
Antenna
Frequency:
Bandwidth:
Impedance:
adjustments to the antenna arm and the antenna radome.
You will have to loosen the Phillips screws to rotate and
adjust. Once the adjustment has been made to the desired
position, tighten the Phillips screw. Be careful not to over
tighten. We recommend that you make the adjustments,
if needed, to each area in the order that is shown below.
2332.5 to 2345 MHz
12.5 MHz
50 ohms
Polarization:
LHCP (Circular)
LNA
Gain:
2
30 dB, typical
1 dB, typical
70 mA, maximum
Noise Figure :
Current Drain:
Mechanical Specifications
Antenna Dimensions:
Radome:
1
3 1/4” x 3 1/4"
8”
Arm Length:
Mounting bracket:
4 3/4" x 2 7/8”
Cable Type:
Cable Length:
RG-6 coaxial (sold separetly)
Up to 100 feet
Cable Installation
Connectors Antenna:
Connectors Cable:
Adapter:
F connector
F connector
F connector to SMB
At this point you are ready to attach the RG6 coaxial cable
(sold separately). Take either end of cable and insert it
through the rubber boot then screw the connector onto
the bottom of the antenna as shown below. Screw the
connector on by hand as far as it can go. It is not necessary
to use any special tools for this.
Mounting Hardware
Nuts:
Screws and U-Bolts:
Weight including cable:
Stainless Steel
Stainless Steel
1.75 lbs
Once the cable is secured
onto the antenna, slide
the rubber onto the
antenna as shown.
For improved wire
Other Specifications
Temperature:
-40 °F to +185 °F, operating
Quality and Performance Tests
XM Approved:
management, the
Per Specification
coaxial cable can be
inserted into a notch
near the bottom of
mounting bracket.
RX000002H-010000
At this point, please determine the best way to route the
rest of the cable into your home to the XM home receiver
or XM Plug & Play system.
If additional cable length is required an in-line amplifer
(XMAMP18) is needed for each additional 100 feet of
RG6 coaxial cable.
6
7
|