1
2
3
4
What’s in the Box?
XpressRC functions
5-way navigation knob
If you placed the XM antenna on the front
of the vehicle, route the cable across the
top of the windshield. Gently pry up the
rubber weather seal and tuck the cable
underneath. Follow the weather seal
down to the door jam. Tuck the cable into
the door jam and up to the dash or under
the carpet to the car cradle as shown.
• Turn the knob to scroll through a list.
60-Minute Replay Buttons
Pause and replay up to 60
minutes of live XM broadcast.
Display
Customize the way you view
content on the display
• Press the center of the XM button to make a selection.
• Press the edge of the XM button to select display, jump,
info
display
mute
menu
+
or
.
Power Button
1
2
5
8
0
3
6
Cassett Adaptor
4
7
XM Button
Confirms selection for
channel and menu items, also
press and hold to GameSelect,
to TuneSelect or to save a song.
9
XpressRC
Swivel Mount
Preparation Kit
jump
fav
Remote Control
Left and Right Arrows
Search for channels by
category.
Press center button Toggle right
(XM button)
Toggle left
Toggle up
Toggle down
Swivel Mount
Vent Mount
If you placed the XM antenna on the
rear of the vehicle, route the cable
under the weather seal of the rear
window. Route it into the trunk and
through any existing wire passages or
cargo passages to the rear passenger
compartment. Tuck the cable under the
door jam trim or under the carpet to
the radio as shown.
5-way Navigation
Knob
Previews channels; also selects
various menu options.
Car Power Adapter
Vehicle Installation
Car Cradle
Step 1: Mount the XM Antenna
Menu
1
Choose the best location for your XM
antenna considering your own
XM Car Antenna
Access advanced features
and configuration options.
WARNINGS:
•
personal situation. Pay particular
attention to any accessories that you
may have like luggage racks and how
frequently you may use them.
When using this product it is always important to keep your eyes on the road and hands on
Fav
Number Keys
Enter a channel
directly, select your
Info
Jump
the wheel. Not doing so could result in personal injury, death, and/or damage to your XpressRC
Receiver, accessories, and/or to your vehicle or other property.
Choose among direct
channel entry, favorite
channels, and SongSaver
mode.
Displays either your
personal stock or info
Switches between
current channel and
previous channel.
Magnet
TIP! Always be careful to include enough slack in your cable to accommodate
open doors or trunk lids. Use things typically found around the home, like
electrical tape, to secure cables in areas so that hinges do not pinch the cable
with the door. Hide any excess cable in the trim.
favorite channels, or extras information.
access songs saved
• XpressRC should be placed in your vehicle where it will not interfere with the function of
safety features, e.g., deployment of airbags. Failure to correctly place Xpress may result in injury
to you or others if the unit becomes detached during an accident and/or obstructs the deploy-
ment of an airbag.
in SongSaver.
The XM antenna contains a strong magnet which
will stick to any metal parts of your vehicle.
5
7
6
8
Step 3: Connect your XpressRC
Step 2: Install the vent or swivel mount
You can use either the vent mount or the swivel mount for your
XpressRC depending on your particular situation.
Installing the swivel mount
1
2
3
Plug the antenna into ANT IN on the cradle.
CAUTION: The adhesive used with the swivel mount may make it difficult to remove. Do not
install this mount on leather surfaces and make sure the air temperature is at least 60°F (15°C).
Plug the power adapter into DC IN on the cradle.
Plug the audio adapter into AUDIO OUT on the cradle.
Installing the vent mount
1
Locate a flat surface for the mount. Make sure there is ample room
for the XM cradle and radio when installed.
1
Locate a vent with horizontal slats sturdy enough
to hold your XM cradle and radio.
• Use the Cassette Adapter if your vehicle has a built-in cassette player.
• Use a mini audio cable (sold separately) if your vehicle has
an audio input jack.
Vent Mount
DC IN
ANT IN
AU
D
IO OUT
2
3
Clean the surface with the preparation kit and let it dry thoroughly.
2
3
Adjust the clamps to fit your vent.
Snap the mount onto the vent.
Peel off the adhesive liner. Position, press, and hold the swivel mount
in place for 30 seconds.
XpressRC Car Cradle
Extra Adhesive
Pad
4
5
Insert the cradle into the mount.
Insert your XpressRC into the cradle.
To remove, push the mount into the vent, then lift up.
IMPORTANT: Let the adhesive cure for 24 hours before attaching the XM
cradle and radio to the mount.
NOTE: If your car does not contain a cassette player or an audio input, you will need to
use either the XM SureConnect (sold separately) or the FM Direct adapter (sold separately).
4
Turn the swivel to accommodate the XM cradle and radio. Adjust the tension via
the center screw.
Power Adapter
• XM SureConnect (sold separately): You can listen to your XpressRC through your car
stereo by using XpressRC’s built-in FM modulator and the XM SureConnect. Simply find
an unused FM frequency on the stereo and set your XpressRC to transmit on that same
frequency. Refer to Set the FM frequency page in your user guide for more information.
Dash
Dash
Swivel Mount
You can adjust this screw
to adjust the tension of the
mount with a screwdriver.
XM Antenna
Vent
Vent
FM Direct Adapter (sold separately): This option directly connects the XpressRC to your
•
car’s audio system and antenna. A professional installation is recommended if you choose
to use this method.
Cassette Adapter
To remove, carefully lift the adhesive pad with your fingers or a spoon. Warming
the pad with a hair dryer for several minutes will help soften the adhesive.
You can reinstall the swivel mount using the extra adhesive pad.
|