RS-485 Digital I/O Module
Model 485SDD16
Document ation Number 485SDD16-1005
pn#3605-r1
This product
Designed and Manufactured
In Ottawa, Illinois
USA
of domestic and imported parts by
B&B Electronics Mfg. Co. Inc.
707 Dayton Road -- P.O. Box 1040 -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Internet:
B&B Electronics -- Revised February 2005
485SDD16-1005 Manual
Cover Page
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Chapter 1- Introduction
485SDD16 Features
The 485SDD16 is a general purpose control module that
operates through an RS-485 interface. The 485SDD16 offers 16
discrete digital I/O lines. With these features, the module can be
used to sense external ON/OFF conditions and to control a variety
of devices.
Each of the sixteen I/O lines can be defined as either an input or
an output. The digital outputs are CMOS compatible. The digital
inputs are CMOS/TTL compatible. The digital I/O lines are available
through a DB-25S (female) connector.
The 485SDD16 connects to the host computer’s RS-485 or RS-
422 serial port using terminal blocks. The address and turn-around
delay are software programmable to allow for use of multiple
devices or connection to existing multi-node systems. The unit
automatically detects baud rates from 1200 to 9600. A data format
of 8 data bits, 1 stop bit and no parity is used.
Configuration parameters are stored in non-volatile memory.
These parameters consists of module address, communication turn-
around delay, I/O definitions, and output power-up states.
The unit is powered by connecting +12Vdc to terminal blocks or
to the DB-25S I/O connector.
Figure 1.2 - Simplified Block Diagram
Packing List
Examine the shipping carton and contents for physical damage.
The following items should be in the shipping carton:
1. 485SDD16 unit
2. Software
3. This instruction manual
If any of these items are damaged or missing contact B&B
Electronics immediately.
485SDD16 Specifications
I/O Lines
Total:
16 (Factory default = inputs)
Inputs
Voltage Range:
Low Voltage:
High Voltage:
Leakage Current:
0 Vdc to 5 Vdc
1.0 Vdc max.
2.0 Vdc min.
Figure 1.1 - 485SDD16 Module
1 microamp max.
Outputs
Low Voltage:
High Voltage:
0.6 Vdc @ 8.3 milliamps (Sink)
4.3 Vdc @ -3.1 milliamps (Source)
485SDD16-1005 Manual
1
2
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Power Supply
Input Voltage:
8 Vdc to 16 Vdc @ 35 milliamps
(Doesn’t include the power
consumption of external devices.)
Terminal Blocks or DB-25S
Connection:
Communications
Standard:
RS-422/485
Addresses:
Turn-around Delay:
256 (Factory default = 48 decimal)
Software programmable from 0 to
255 character transmission times.
(Factory default = 1)
Baud Rate:
Format:
Connection:
1200 to 9600 (automatic detection)
8 data bits, 1 stop bit, no parity
Terminal Blocks
Optical Isolation: If optical isolation is required, use B&B’s
485HSPR high-speed optically isolated converter with this product.
Size
0.7" x 2.1" x 5.2"
485SDD16-1005 Manual
3
4
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Serial Port Connections
Chapter 2 - Connections
In order to communicate to the 485SDD16 module it must be
connected to an RS-422/RS-485 serial port. The 485SDD16 will
work on a 2-wire or 4-wire RS-485 multi-node network. Refer to
B&B Electronics’ free RS-422/485 Application Note for more
information. The unit automatically detects baud rates from 1200 to
9600. A data format of 8 data bits, 1 stop bit and no parity is used.
Connections are made using terminal blocks. Table 2.2 shows the
terminal blocks and their functions.
This chapter will cover the connections required for the
485SDD16. There are three sets of connections: digital I/O, serial
port, and power supply. Do not make any connections to the
485SDD16 until you have read this chapter.
Digital I/O Connections
Connections to the I/O lines are made through the DB25S
(female) I/O port connector. Refer to Table 2.1. See Chapter 5 for
I/O interfacing examples.
Table 2.2 - RS-485 Terminal Block Connections
Signal
Digital Inputs
TB
Label
Direction at
485SDD16
The digital input lines are CMOS/TTL compatible and can handle
voltages from 0Vdc to +5Vdc.
Digital Outputs
The digital output lines have a maximum voltage of +5Vdc and
are CMOS compatible.
Ground
Signal
Frame
Notes
FR
-
Connection for frame ground.
GND Ground
TD(A) Transmit
Data (A)
TD(B) Transmit
Data (B)
RD(A) Receive
Data (A)
RD(B) Receive
Data (B)
Output
Output
Input
Input
Input
-
Connection is required. [Loop to
RD(A) for 2-wire hookup]
Connection is required. [Loop to
RD(B) for 2-wire hookup]
Connection is required. [Loop to
TD(A) for 2-wire hookup]
Connection is required. [Loop to
TD(B) for 2-wire hookup]
This pin should be connected to the external digital devices
ground.
Table 2.1 - 485SDD16 I/O Port Pinout
DB-25S
DB-25S
+12V +12 Vdc
Power
GND Ground
Connection is required.
Pin #
Function
Pin #
Function
I/O #15
1
2
3
4
5
6
7
8
9
10
11
12
13
No connection
No connection
No connection
No connection
No connection
No connection
Ground
+12Vdc Input
I/O #0
I/O #1
14
15
16
17
18
19
20
21
22
23
24
25
Connection for Signal GND and
Power Supply GND.
I/O #14
I/O #13
I/O #12
I/O #11
I/O #10
No connection
I/O #9
I/O #8
I/O #7
I/O #6
I/O #5
A typical 2-wire RS-485 connection is shown in Figure 2.3 and a
typical RS-422 (or RS-485 4-wire) connection is shown in Figure
2.4. Note that the 485SDD16 data line labels use “A” and “B”
designators (per EIA RS-485 Specification). However, some RS-485
equipment uses “+” and “-“ as designators. In almost all cases, the
“A” line is the equivalent of the “-“ line and the “B” is the equivalent of
the “+” line. With an RS-485/422 system there are other factors that
require consideration, such as termination and turn-around delay.
For more information refer to B&B Electronics’ free RS-422/485
Application Note.
I/O #2
I/O #3
I/O #4
485SDD16-1005 Manual
5
6
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Figure 2.3 - RS-422 4-wire Connection
Figure 2.1 - Example of Multi-Node Network
Power Supply Connections
485SDD16
485SDD16
485SDD16
Power to the 485SDD16 must be supplied by an external power
supply connected to the +12Vdc and GND terminal blocks or to the
I/O connector. An external power supply must be able to supply 8 to
16 Vdc at 35ma.
NOTE: Power requirements of the module does not include the
power consumption of any external devices connected to the
module. Therefore, any current that is sourced by the digital outputs
must be added to this value and the current must not exceed the
maximum output source current. Refer to the 485SDD16
Specification Section of Chapter 1.
Figure 2.2 - RS-485 2-wire Connection
485SDD16-1005 Manual
7
8
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Table 3.2 - Equivalent Values
ASCII Decimal Hexadecimal
Chapter 3 - Commands
There are only two commands required to control the 485SDD16:
set output lines, and read I/O lines. Five additional commands are
used for configuring the module: set module address, set turn-
around delay, define I/O lines, set power-up states, and read
configuration. Command strings are from four to six bytes in length:
the “!” character, an address byte, two command characters, and
one or two data bytes (if required). (See Table 3.1).
!
0
33
48
65
67
68
79
82
83
21h
30h
41h
43h
44h
4Fh
52h
53h
A
C
D
O
R
S
Table 3.1 - 485SDD16 Commands
Function
Command
Response
Read I/O Lines
Set Output Lines
!{addr}RD
!{addr}SO{I/O msb}{I/O
lsb}
{I/O msb}{I/O lsb}
no response
Syntax
Command strings consist of four to six bytes. The first byte is the
start of message byte. The start of message byte is always the
ASCII “!” character. The second byte is the address byte. This byte
allows each unit to have a unique address. The factory default
address is the ASCII "0" character. The next two bytes are the
command characters. These bytes are ASCII characters and used
to specify which command will be executed by the module. Some
commands require an argument field containing a fifth and
sometimes a sixth data byte. Commands that manipulate I/O lines
require two data bytes, a Most Significant and a Least Significant
data byte respectively.
Set Module Address !{addr}SA{new adr}
no response
no response
Set Turn-around
Delay
!{addr}SC{#}
Define I/O Lines
!{addr}SD{I/O msb}{I/O lsb} no response
Set Power-up States !{addr}SS{I/O msb}{I/O lsb} no response
I/O Definitions
Read Configuration
!{addr}RC
{I/O msb}{I/O lsb}
Power-up States
{I/O msb}{I/O msb}
RS-485 Config.
{addr}{t-a delay}
Command Syntax: !
0
|
|
|
|
_
|
|
|
|
_
|
|
_
|
|
_
|
Symbols: {...} represents one byte
<...> represents a numeric value
|
|
|
|
|
|
6th Data Byte
|
5th Data Byte
Before going into the specifics of each command, it is important
to understand that a byte has a numeric value from 0 to 255. The
byte's value can be represented in decimal (0 - 255) format,
hexadecimal (00 - FF) format, binary (00000000 - 11111111) format,
or as an ASCII character. The fixed bytes of each command will be
represented as ASCII characters. For example the Read I/O
command contains the following ASCII characters: “!" and "RD”.
Refer to Table 3.1. However, it is important to remember that an
ASCII character has a numeric value. Example: the ASCII "0" (zero)
does not have a numeric value of zero but has a value of 48. The
decimal and hexadecimal equivalents of some ASCII characters are
shown in Table 3.2. Some commands require additional data bytes
to complete the command. These data bytes may be represented in
any of the formats list above. Refer to Appendix A for more ASCII
and decimal equivalents.
2nd Command Byte
|
1stCommand Byte
Address Byte
Start of Message Byte
I/O Data Bytes
When constructing commands to manipulate output lines or
when reading the state of the I/O lines it is necessary to know how to
select and interpret the I/O data bytes. The sixteen I/O lines are
represented by two data bytes. The Most Significant data byte
represents I/O lines #15 through #8 and the Least Significant data
byte represents I/O lines #7 through #0. The Most Significant byte is
always sent and received first followed by the Least Significant byte.
485SDD16-1005 Manual
9
10
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Read I/O Lines Command
A byte represents an eight-bit binary number (11111111),
therefore each byte can represent eight I/O lines. Each bit is
assigned a bit position and a weight (value). Refer to Table 3.3.
The Read I/O Lines command returns two data bytes that reflect
the state of the I/O lines. The first data byte contains the most
significant I/O lines (15 - 8). The second data byte contains the least
significant I/O lines (7 - 0). If a bit is a "0" then the state of that I/O
line is LOW. If a bit is a "1" then the state of that I/O line is HIGH.
Table 3.3 - Bit Assignments for I/O Lines
MOST SIGNIFICANT I/O BYTE
Command: !{addr}RD
Argument: none
Response: the state of the 16 I/O lines in two 8 bit bytes. (shown in
bold face)
ASCII Example:!0RDÈR
Dec. Example: !0RD<200><82>
Hex. Example: !0RD<C8><52>
Bin. Example: !0RD<11001000><01010010>
Description: Read module 0's (decimal 48) I/O lines. The first byte
indicates that I/O lines #15, 14, & 11 are HIGH and I/O lines # 13,
12, 10, 9, & 8 are LOW; the second byte indicates that I/O lines # 6,
4, & 1 are HIGH and I/O lines # 7, 5, 3, 2, & 0 are LOW.
I/O Line #
Bit Position
Hex Weight
15
14
13
12
11
10
9
1
2
2
8
0
1
1
7
6
5
4
3
2
4
4
80
40
20
32
10
16
8
8
Dec. Weight 128 64
LEAST SIGNIFICANT I/O BYTE
I/O Line #
Bit Position
Hex Weight
7
7
80
6
6
40
5
5
20
32
4
4
10
16
3
3
8
8
2
2
4
4
1
1
2
2
0
0
1
1
Dec. Weight 128 64
To set an output to a HIGH state the corresponding bit position
must be set to a "1". Conversely to set an output LOW the
corresponding bit position must be set to a "0". When reading I/O
lines, any bit set to a "0" indicates the corresponding I/O line is in
the LOW state and any bit set to a "1" indicates the corresponding
I/O line is in the HIGH state.
Set Output Lines Command
The Set Output Lines command is used to set the states of the
output lines. This command requires two data bytes. These data
bytes specify the output state of each output line. The first data byte
represents the most significant I/O lines (15 - 8). The second data
byte represents the least significant I/O lines (7 - 0). If a bit position
is set to a "0" then the state of that output line will be set LOW. If a
bit position is set to a "1" then the state of that output line will be set
HIGH.
Example 3.1 - To set outputs 15, 8, 1, and 0 to a HIGH state, and all
other outputs to a LOW state (shown in bold face) -
MS Byte
10000001
129
LS Byte
00000011
3
(2+1)
3
Shown in binary -
Shown in decimal -
NOTE: Refer to the "Define I/O Lines" command to define an I/O line
as an output.
(128+1)
81
Shown in hexadecimal -
(80h+1h)
(2h+1h)
Command: !{addr}SO
Argument: {I/O msb}{I/O lsb}
Response: none
ASCII Example:!0SOUA
Dec. Example: !0SO<85><65>
Example 3.2 - Reply from Read I/O command (shown in bold face) -
MS Byte
11001000
200
LS Byte
01010010
82
Shown in binary -
Shown in decimal -
Hex. Example: !0SO <55><41>
(128+64+8)
C8
(64+16+2)
52
Bin. Example: !0SO<01010101><01000001>
Description: Set module 0's (decimal 48) output lines. The first byte
sets output lines #14, 12, 10, & 8 HIGH and output lines #15, 13,
11, & 9 LOW; the second byte sets output lines #6, & 0 HIGH and
output lines # 7, 5, 4, 3, 2, & 1 LOW. Note: If any of these lines are
defined as inputs the bit settings are ignored.
Shown in hexadecimal -
(80h+40h+8h)
(40h+10h+2h)
I/O lines #15, 14, 11, 6, 4, 1 are HIGH and all other I/O lines are
LOW.
485SDD16-1005 Manual
11
12
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Define I/O Lines Command
The Define I/O Lines command is used to define each of the 16
I/O lines as either an input or an output. This command requires two
data bytes. Each data byte defines eight I/O lines. The first data
byte defines the eight most significant I/O lines (15 - 8). The second
data byte defines the eight least significant digital I/O lines (7 - 0). If
a bit position is set to a "0" then the I/O line will defined as an input.
If a bit position set to a "1" then the I/O line will be defined as an
output.
Set Module Address Command
The Set Module Address command is used to change the
address of a 485SDD16. This commands requires one data byte.
This data byte is used to specify the module's new address.
Addresses can be assigned any decimal value from 0 to 255. The
address is stored in non-volatile memory and is effective
immediately. Each module must be assigned its own unique
address when connected to an RS-485 muti-node network.
Command: !{addr}SD
Argument: {I/O msb}{I/O lsb}
Response: none
ASCII Example:!0SDUA
Dec. Example: !0SD<85><65>
Command: !{addr}SA
Argument: {new address}
Response: none
ASCII Example:!0SA9
Hex. Example: !0SD<55><41>
Dec. Example: !0SA<57>
Bin. Example: !0SD<01010101><01000001>
Description: Define module 0's (decimal 48) I/O lines. The first byte
define I/O lines #14, 12, 10, & 8 as outputs and I/O lines #15, 13,
11, & 9 as inputs; the second byte define I/O lines #6, & 0 as outputs
and I/O lines #7, 5, 4, 3, 2, & 1 as inputs.
Hex. Example: !0SA<39>
Bin. Example: !0SA<00111001>
Description: Change module address from ASCII "0" (48 decimal) to
address ASCII "9" (57 decimal).
Set Turn-around Delay Command
The Set Turn-around Delay command sets the amount of time
the 485SDD16 waits before transmitting its response. This ensures
that no two drivers are enabled at the same time on a two-wire RS-
485 network. The turn-around delay is stored in non-volatile
memory. This command requires a data byte that specifies the turn-
around delay. Where {turn-around delay} is a number from 0 to 255.
One unit of turn-around is equal to one character transmission time.
The turn-around delay can be computed as follows:
character time = (1 / baud rate) * 10
turn-around delay = character time * data byte
Command: !{addr}SC
Argument: {turn-around delay}
Response: none
ASCII Example:!9SC♦
Dec. Example: !9SC<04>
Hex. Example: !9SC<04>
Bin. Example: !9SC<00000100>
Description: Set module 9's (decimal 57) turn-around delay to four
character transmission times (@ 9600 baud the turn-around delay =
4.17ms).
485SDD16-1005 Manual
13
14
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
ASCII Example:!9RCUAP@9♦
Dec. Example: !9RC<85><65><80><64><57><04>
Hex. Example: !9RC<55><41><50><40><39><04>
Bin. Example: !0RC<01010101><01000001><01010000><01000000>
<00111001><00000100>
Description: Read module 9's (decimal 57) configuration. The first
byte (MSB of I/O definitions) - I/O lines #14, 12, 10, & 8 are outputs
and I/O lines #15, 13, 11, & 9 are inputs; the second byte (LSB of
I/O definitions) - I/O lines #6, & 0 are outputs and I/O lines #7, 5, 4,
3, 2, & 1 are inputs; the third byte (MSB of output power-up states) -
output lines #14, & 12 HIGH and output lines #10, & 8 LOW at
power-up; the fourth byte (LSB of output power-up states) - output
line #6 HIGH and output line #0 LOW at power-up; the fifth byte
(module address) is set ASCII "9" (decimal 57); the sixth byte (turn-
around delay) is a decimal 4.
Set Power-up States Command
The Set Power-up States command is used to set the states of
output lines when the module's power is recycled. This command
requires two data bytes. These data bytes specify the output state
of each output line. The first data byte represents the eight most
significant I/O lines (15 - 8). The second data byte represents the
eight least significant I/O lines (7 - 0). If a bit position is set to a "0"
then the state of that output line will be set LOW. If a bit position is
set to a "1" then the state of that output line will be set HIGH.
Command: !{addr}SS
Argument: {I/O msb}{I/O lsb}
Response: none
ASCII Example:!0SSÛ@
Dec. Example: !0SS<219><64>
Hex. Example: !0SS<DB><40>
Bin. Example: !0SS<11011011><01000000>
Description: Set module 0's (decimal 48) power-up states. The first
byte sets output lines #15, 14, 12, 11, 9, & 8 HIGH and output lines
#13, & 10 LOW at power-up; the second byte sets output line #6
HIGH and output lines #7, 5, 4, 3, 2, 1, & 0 LOW at power-up.
NOTE: If any of these lines are defined as inputs the bit settings are
ignored.
Read Configuration Command
The Read Configuration command returns the module's I/O
definitions, the outputs power-up state, the module's address, and
the turn-around delay. Six data bytes are returned. The first two
data bytes contain the definition of the eight most significant I/O lines
(15 - 8) and the eight least significant I/O lines (7 - 0) respectively. If
a bit position is set to a "0" the I/O line is defined as an input, if set to
a "1" the I/O line is defined as an output. The second two data bytes
contain the power-up states of the most significant output lines (15 -
8) and the least significant output lines (7 - 0) respectively. If a bit
position is set to a "0" the power-up state of the output will be LOW,
if set to a "1" the output will be HIGH. The fifth data byte is the
module's address. The sixth data byte is the turn-around delay.
Command: !{addr}RC
Argument: none
Response: definition of the sixteen I/O lines in two 8 bit bytes, and
the power-up states in two 8 bit bytes. (shown in bold face)
485SDD16-1005 Manual
15
16
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Chapter 4 - I/O Interfacing
This chapter will explain "HIGH" and "LOW" states and show
some general examples of how to interface to the I/O lines. Caution
must be taken not to exceed 485SDD16 specifications listed in
Chapter 1 when interfacing to external devices. Failure to stay
within these specifications could result in damage to the unit and will
void warranty.
Digital Inputs
As stated earlier, digital input lines are CMOS/TTL compatible
and can only handle voltages from 0Vdc to +5Vdc.
Digital inputs are used to sense a HIGH or a LOW state. This
can be accomplished via switch closures, contact closures, or a
solid state digital signal. When an I/O line, defined as an input,
senses a voltage level above +2.0Vdc it will be considered "HIGH"
and it's input state will be read as a "1". Conversely, when an input
senses a voltage level below +1.0Vdc it will be considered "LOW"
and it's input state will be read as a "0".
Figure 4.2 - Solid State Input
Inputs can also be used to sense AC voltages by using
mechanical or solid state relays. Solid state relays are available
from many manufacturers.
Figures 4.1 - 4.4 show examples of some typical input interfaces.
Figure 4.3 - Isolated Mechanical Input
Figure 4.1 - Switch Input
485SDD16-1005 Manual
17
18
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Figure 4.4 - Isolated Solid State Input
Digital Outputs
Figure 4.6 - Isolated Solid State Output
Digital outputs are used to turn on or turn off external devices.
Digital outputs are CMOS compatible and operate between 0Vdc
and +5Vdc. Outputs can be used to control solid state output
modules, CMOS and TTL logic circuits. Caution must be taken not
to exceed the power capability of the outputs. Refer to the output
specifications in Chapter 1.
Setting an output line to a "1" forces the output HIGH, and setting
an output line to a "0" forces the output LOW.
Figures 4.5 - 4.6 show examples of some typical output
interfaces.
Figure 4.5 - Solid State Output
485SDD16-1005 Manual
19
20
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Example 5.1 - Determining the status of I/O lines #2 & #10 of
module #5.
Chapter 5 - Software
Maddr = 5
mask = &H4
Cmnd$ = "!" + CHR$(Maddr) + "RD"
PRINT #1, Cmnd$;
MSIO$ = INPUT$(1,#1)
This chapter will be divided into two sections. The first section
covers programming techniques for constructing a command string,
receiving data and manipulating data in QuickBASIC. The second
section discusses how to install and run the demonstration program
on an IBM PC or compatible.
LSIO$ = INPUT$(1,#1)
MSIO = ASC(MSIO$)
LSIO = ASC(LSIO$)
Programming Techniques
MSstatus = MSIO AND mask
LSstatus = LSIO AND mask
If LSstatus equals zero then I/O line #2 is LOW. If LSstatus is not
equal to zero then I/O line #2 is HIGH. If MSstatus equals zero then
I/O line #10 is LOW. If MSstatus is not equal to zero then I/O line
#10 is HIGH.
This section shows steps and examples of programming the
485SDD16 in QuickBasic. If you are programming in another
language, this section can be helpful as a guideline for programming
the 485SDD16.
Read I/O Lines Command
The Read I/O Lines command returns two data bytes that
represents the states of the module's I/O lines. Refer to this
command in Chapter 3 for more information.
Step 1 - Constructing the command string:
Cmnd$ = "!" + CHR$(Maddr) + "RD"
Where Maddr is the address of the module that is to return its I/O
states.
Step 2 - Transmitting the command string:
PRINT #1, Cmnd$;
Step 3 - Receiving the data:
MSIO$ = INPUT$(1,#1)
Table 5.1 - Digital I/O Mask Values
Mask Values
I/O Line #
Hexadecimal
Decimal
0 & 8
1 & 9
1H
2H
1
2
2 & 10
3 & 11
4 & 12
5 & 13
6 & 14
7 & 15
4H
8H
10H
20H
40H
80H
4
8
16
32
64
128
LSIO$ = INPUT$(1,#1)
Step 4 - Manipulating the data:
MSIO = ASC(MSIO$)
LSIO = ASC(LSIO$)
Read Configuration Command
The Read Configuration command reads the module's I/O
definitions, Power-up states, Address, and Turn-around delay
respectively. Refer to this command in Chapter 3 for more
information.
Step 1 - Constructing the command string:
Cmnd$ = "!" + CHR$(Maddr) + "RC"
Where Maddr is the address of the module that is to return its
configuration.
Step 5 - Determining an I/O's status:
MSstatus = MSIO AND mask
LSstatus = LSIO AND mask
By "ANDing" the value of MSIO or LSIO with the appropriate
mask of an I/O line, the status of the I/O line can be determined.
If the status is equal to zero the I/O line is LOW. If the status is not
equal to zero the I/O line is HIGH. Table 5.1 shows the mask
values for each I/O line.
Step 2 - Transmitting the command string:
PRINT #1, Cmnd$;
Step 6 - Repeat Step 5 until the status of each I/O line has been
determined.
485SDD16-1005 Manual
21
22
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Maddr = 5
Step 3 - Receiving the data:
mask = &H4
MSdefs$ = INPUT$(1,#1)
Cmnd$ = "!" + CHR$(Maddr) + "RC"
PRINT #1, Cmnd$;
LSdefs$ = INPUT$(1,#1)
MSpups$ = INPUT$(1,#1)
MSdefs$ = INPUT$(1,#1)
LSdefs$ = INPUT$(1,#1)
MSpups$ = INPUT$(1,#1)
LSpups$ = INPUT$(1,#1)
Maddr$ = INPUT$(1,#1)
Mtdly$ = INPUT$(1,#1)
MSdefs = ASC(MSdefs$)
LSdefs = ASC(LSdefs$)
MSpups = ASC(MSpups$)
LSpups = ASC(LSpups$)
Maddr = ASC(Maddr$)
Mtdly = ASC(Mtdly$)
LSpups$ = INPUT$(1,#1)
Maddr$ = INPUT$(1,#1)
Mtdly$ = INPUT$(1,#1)
Step 4 - Manipulating the data:
MSdefs = ASC(MSdefs$)
LSdefs = ASC(LSdefs$)
MSpups = ASC(MSpups$)
LSpups = ASC(LSpups$)
Maddr = ASC(Maddr$)
Mtdly = ASC(Mtdly$)
Step 5 - Determining the I/O line definitions:
MSdefs = MSdefs AND mask
LSdefs = LSdefs AND mask
MSdefs = MSdefs AND mask
LSdefs = LSdefs AND mask
MSpups = MSpups AND mask
LSpups = LSpups AND mask
By "ANDing" the value of MSdefs or LSdefs with the appropriate
mask of an I/O line, the I/O line definition can be determined. If
the status is equal to zero the I/O line is an INPUT. If the status is
not equal to zero the I/O line is an OUTPUT. Table 5.1 shows the
mask values for each I/O line.
Step 6 - Repeat Step 5 until the status of each I/O line has been
determined.
Step 7 - Determining an OUTPUT's Power-up state:
MSpups = MSpups AND mask
If LSdefs equals zero then I/O line #2 is an INPUT and if not equal
to zero then I/O line #2 is an OUTPUT. If MSdefs equals zero then
I/O line #10 is an INPUT and if not equal to zero then I/O line #10 is
an OUTPUT. If LSpups equals zero then Output line #2's power-up
state is LOW and if not equal to zero then Output line #2's power-up
state is HIGH. If MSpups equals zero then Output line #10's power-
up state is LOW and if not equal to zero then Output line #10's
power-up state is HIGH. Maddr is the decimal address of the
module. Mtdly is the decimal number of character times that make
up the turn-around delay.
LSpups = LSpups AND mask
By "ANDing" the value of MSpups or LSpups with the appropriate
mask of an Output line, the Output line definition can be
determined. If the status is equal to zero the Output power-up
state will be LOW. If the status is not equal to zero the Output
power-up state will be HIGH. Table 5.1 shows the mask values
for each I/O line.
Set Output States Command
The Set Output States command is used to set the states of any
I/O line that is defined as an output. This command requires two
data bytes. Refer to this command in Chapter 3 for more
information.
Step 1a - Construct the command string:
Set appropriate outputs HIGH
Step 8 - Repeat Step 7 until the power-up state of each Output line
has been determined.
Example 5.2 - Determining the definition and power-up state of I/O
lines #2 & #10 of module #5.
MSstates = MSstates OR mask
LSstates = LSstates OR mask
By "ORing" the current states with the appropriate mask of a
digital output line, the output's bit will be set to a "1" (HIGH).
485SDD16-1005 Manual
23
24
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Step 1b - Define an I/O line as an Input
MSdefs = MSdefs AND (NOT(mask))
Step 1b - Set appropriate outputs LOW
MSstates = MSstates AND (NOT(mask))
LSstates = LSstates AND (NOT(mask))
By "ANDing" the current states with the complement of the
appropriate mask of a digital output line, the output's bit will be set
to a "0" (LOW).
Step 1c - Completing the command string:
Cmnd$ = "!" + CHR$(Maddr) + "SO" + CHR$(MSstates) +
CHR$(LSstates)
LSdefs = LSdefs AND (NOT(mask))
By "ANDing" the current definitions with the complement of the
appropriate I/O line mask the I/O line's data bit will be set to a "0"
(LOW) and the I/O line will be defined as an Input.
Step 1c - Completing the command string:
Cmnd$ = "!" + CHR$(Maddr) + "SD" + CHR$(MSdefs) +
CHR$(LSdefs)
Step 2 - Transmitting the command string:
Print #1, Cmnd$;
Step 2 - Transmitting the command string:
Print #1, Cmnd$;
Example 5.4 - Define I/O line #7 as an Output (HIGH) and I/O line #8
as an input (LOW) on module #4.
'Set module's address to 4.
Maddr = 4
'Set bit 7 of LSdefs to make I/O line #7 an Output (HIGH).
LSdefs = LSdefs OR &H80
'Clear bit 0 of MSdefs to make I/O line #8 an Input (LOW).
MSdefs = MSdefs AND (NOT(&H1))
Cmnd$ = "!" + CHR$(Maddr) + "SD" + CHR$(MSdefs) +
CHR$(LSdefs)
PRINT #1, Cmnd$;
MSIO$ = INPUT$(1,#1)
Example 5.3 - Set Output #0 HIGH and Output #14 LOW of module
#5.
'Set module address.
Maddr = 5
'Set bit 0 of LSstates to make Output #0 HIGH.
LSstates = LSstates OR &H1
'Clear bit 4 of MSstates to make Output #14 LOW.
MSstates = MSstates AND (NOT(&H40))
Cmnd$ = "!" + CHR$(Maddr) + "SO" + CHR$(MSstates) +
CHR$(LSstates)
I/O #7 will be defined as an Output (HIGH) and I/O line #8 will be
defined as an Input (LOW) of module #4. All other I/O definitions will
not be changed.
PRINT #1, Cmnd$;
Output #0 will be set HIGH and output #14 will be set LOW of
module #5. All other output settings of module #5 will not be
changed.
Set Power-up States Command
The Set Power-up States command is used to set the states of
the digital outputs at power-up. This command requires two data
bytes. Refer to this command in Chapter 3 for more information.
Step 1a - Construct the command string:
Set appropriate outputs power-up states HIGH
MSpups = MSpups OR mask
Define I/O Lines Command
The Define I/O Lines command is used to define each of the
module's I/O lines as either an input or an output. This command
requires two data bytes. Refer to this command in Chapter 3 for
more information.
LSpups = LSpups OR mask
Step 1a - Construct the command string:
Define an I/O line as Output
MSdefs = MSdefs OR mask
By "ORing" the current power-up states with the appropriate mask
of a digital output line, the power-up state's data bit will be set to a
"1" (HIGH).
LSdefs = LSdefs OR mask
By "ORing" the current definitions with the appropriate I/O line
mask, the I/O line's data bit will be set to a "1" (HIGH) and the I/O
line will be defined as an Output.
485SDD16-1005 Manual
25
26
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Example 5.6 - Change the address of module with a current address
of 4 decimal to the new address of 5 decimal.
Step 1b - Set appropriate outputs power-up states LOW
MSpups = MSpups AND (NOT(mask))
LSpups = LSpups AND (NOT(mask))
Maddr = 4
Naddr = 5
Cmnd$ = "!" + CHR$(Maddr) + "SA" + CHR$(Naddr)
Print #1, Cmnd$;
By "ANDing" the current power-up states with the complement of
the appropriate mask of a digital output line, the power-up state's
data bit will be set to a "0" (LOW).
Step 1c - Completing the command string:
Cmnd$ = "!" + CHR$(Maddr) + "SS" + CHR$(MSpups) +
CHR$(LSpups)
Set Turn-around Delay Command
The Set Turn-around Delay command is used to set the amount
of time the module will wait after receiving a command before it
sends the response message. This ensures that no two
communication drivers will be enabled at the same time, and is
necessary when multiple modules share the same communica-
tion lines. The command requires one data byte to specify the turn-
around delay. Refer to this command in Chapter 3 for more
information.
Step 2 - Transmitting the command string:
Print #1, Cmnd$;
Example 5.5 - Set Output #5's power-up state HIGH and Output
#13's power-up state LOW on module #4.
'Set module address to 4.
Step 1 - Construct the command string:
Maddr = 4
Cmnd$ = "!" + CHR$(Maddr) + "SC" + CHR$(Ntdly)
Where Maddr if the module's address and Ntdly is the module's
new turn-around delay.
Step 2 - Transmitting the command string:
Print #1, Cmnd$;
'Set bit 0 of LSpups to make Output #5's power-up state HIGH.
LSpups = LSpups OR &H20
'Clear bit 4 of MSpups to make Output #13's power-up state LOW.
MSpups = MSpups AND (NOT(&H20))
Cmnd$ = "!" + CHR$(Maddr) + "SS" + CHR$(MSpups) +
CHR$(LSpups)
PRINT #1, Cmnd$;
MSIO$ = INPUT$(1,#1)
Module's #4 output line #5's power-up state will be set HIGH and
output line #13's power-up state will be set LOW. All other output
power-up states will not be changed.
Example 5.7 - Set the turn-around delay of module #5 to 10
character times.
Maddr = 5
Ntdly = 10
Cmnd$ = "!" + CHR$(Maddr) + "SC" + CHR$(Naddr)
Print #1, Cmnd$;
Set Module Address Command
The Set Module Address command is used to change the
address of the 485SDD16. This command requires a data byte.
The data byte is used to specify the new address of the module.
Step 1 - Construct the command string:
Cmnd$ = "!" + CHR$(Maddr) + "SA" + CHR$(Naddr)
Where Maddr if the module's current address and Naddr is the
module's new address.
Step 2 - Transmitting the command string:
Print #1, Cmnd$;
485SDD16-1005 Manual
27
28
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Demonstration Program
The 485SDD16 Demonstration (SDD16) Program (IBM PC or
Compatible) provides the user with examples of how to receive and
transmit commands to the 485SDD16. The SDD16.EXE is the
executable program, the SDD16.BAS file is the source code in
QuickBASIC. The source code provides an illustration of how to
send and receive commands from the 485SDD16.
NOTE: This is a demonstration program only and not intended for
system applications.
Running Demonstration Program
Before you can run the demonstration program you must run the
install program in the Hard Drive Installation section. If you are
running Windows, exit Windows to DOS.
To run the program follow these steps from the DOS prompt:
1. Type CD \485SDD16 and press the <Enter> key.
2. Type SDD16 and press the <Enter> key.
485SDD16-1005 Manual
29
30
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Decimal ASCII
Decimal ............ASCII
39 .................. "
40 .................. (
41 .................. )
42 .................. *
43 .................. +
44 .................. "
45 .................. -
46 .................. .
47 .................. /
48 .................. 0
49 .................. 1
50 .................. 2
51 .................. 3
52 .................. 4
53 .................. 5
54 .................. 6
57 .................. 9
58 .................. :
59 .................. ;
60 .................. <
61 .................. =
62 .................. >
63 .................. ?
64 .................. @
65 .................. A
66 .................. B
67 .................. C
68 .................. D
69 .................. E
70 .................. F
71 .................. G
72 .................. H
73 .................. I
74 .................. J
75 .................. K
76 .................. L
77 .................. M
78 .................. N
79 .................. O
0 ................... NUL
1 ................... SOH
2 ................... STX
3 ................... ETX
4 ................... EOT
5 ................... ENQ
6 ................... ACK
7 ................... BEL
8 ................... BS
9 ................... HT
10 ................. LF
11 ................. VT
12 ................. FF
13 ................. CR
14 ................. SO
15 ................. SI
16 ................. DLE
17 ................. DC1
18 ................. DC2
19 ................. DC3
20 ................. DC4
21 ................. NAK
22 ................. SYN
23 ................. ETB
24 ................. CAN
25 ................. EM
26 ................. SUB
27 ................. ESC
28 ................. FS
29 ................. GS
30 ................. RS
31 ................. US
32 ................. SP
33 ................. !
APPENDIX A
ASCII Character Codes
34 ................. "
35 ................. #
36 ................. $
37 ................. %
38 ................. &
485SDD16-1005 Manual
Appendix A
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
A-1
A-2
Appendix A
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Decimal............ ASCII
80 ................. P
81 ................. Q
82 ................. R
83 ................. S
84 ................. T
85 ................. U
86 ................. V
87 ................. W
88 ................. X
89 ................. Y
90 ................. Z
91 ................. [
92 ................. \
93 ................. ]
94 ................. ^
95 ................. _
96 ................. '
97 ................. a
98 ................. b
99 ................. c
100 ............... d
101 ............... e
102 ............... f
103 ............... g
104 ............... h
105 ............... i
106 ............... j
107 ............... k
108 ............... l
109 ............... m
110 ............... n
111 ............... o
112 ............... p
113 ............... q
114 ............... r
115 ............... s
116 ............... t
117 ............... u
118 ............... v
Decimal ...........ASCII
119 ................ w
120 ................ x
121 ................ y
122 ................ z
123 ................ {
124 ................ |
125 ................ }
126 ................ ~
127 ................ DEL
128 ................
129 ................
130 ................
•
•
•
.................
.................
.................
255 ................
485SDD16-1005 Manual
Appendix A
A-3
A-4
Appendix A
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
The decimal (base 10) numbering system represents each
position in successive powers of 10, with each decimal symbol
having a value from 0 to 9. The hexadecimal (base 16) numbering
system represents each position in successive powers of 16 with
each hex symbol having a value of 0 to 15. Since each hex position
must have a single symbol, the symbols "A" through "F" are
assigned to values 10 through 15 respectively. Refer to Table 1.
The information and examples to follow will explain how to convert
from a decimal number to a hexadecimal number and vice versa.
Table 1.
Decimal
Hexadecimal
Value
Symbol
0
1
0
1
2
2
3
3
4
4
5
5
6
6
7
7
8
9
8
9
APPENDIX B
Hexadecimal/Decimal Conversions
10
11
12
13
14
15
A
B
C
D
E
F
485SDD16-1005 Manual
Appendix B
B-1
B-2
Appendix B
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Hexadecimal to Decimal Conversion:
Decimal = (1st Hex digit x 4096) +
(2nd Hex digit x 256) +
(3rd Hex digit x 16) +
(4th Hex digit)
Each "Hex digit" is the decimal equivalent value of the
hexadecimal symbol.
Example: Convert 10FC hexadecimal to decimal.
1
0
15
12
x
x
x
x
4096
256
16
=
=
=
=
4096
0
240
12
1
4348
10FC hex equals 4348 decimal.
Decimal to Hexadecimal Conversion:
Example: Convert 4348 decimal to hexadecimal.
4096 4348
4096
=
=
=
=
1
0
=
=
=
=
1
0
(1st Hex digit)
(2nd Hex digit)
(3rd Hex digit)
(4th Hex digit)
256
16
1
252
0
252
240
12
12
0
15
12
F
C
4348 decimal equals 10FC hexadecimal.
485SDD16-1005 Manual
Appendix B
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B-3
B-4
Appendix B
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
DTB25
The DTB25 connects to the SDD16 models to provide easy
access to the available I/O lines. The DTB25 plugs directly into the
SDD16's DB25S I/O port connector. Each of the twenty-five pins on
the connector is brought out to a terminal block. Refer to Table C.1.
Dimensions: 0.5" x 2.1" x 4.3". An enclosure for the DTB25 is
available.
APPENDIX C
Interface Modules for SDD16 Models
Figure C.1 - DTB25 Outline Drawing
Before connecting any external devices to the DTB25 make sure
the SDD16 module has been properly configured (I/O lines defined,
power-up states set). This will avoid possible damage to the module
and to the external devices. Make sure not to exceed the voltage
and current limits of the SDD16 module, failure to do so could result
in damage to the module and will void the warranty. Refer to the
Specification Section of this Manual.
485SDD16-1005 Manual
Appendix C
C-1
C-2
Appendix C
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Table C.2 - DBM16 I/O Connections
Table C.1 - DTB25 Connections
T.B.1
T.B.2
Label
Function
Label
Function
DB-25P
Pin #
T.B. DB-25P
T.B.
#
Function
Unused.
#
Pin #
Function
I/O7 I/O Line #7
GND Ground
I/O6 I/O Line #6
I/O5 I/O Line #5
GND Ground
I/O4 I/O Line #4
I/O3 I/O Line #3
GND Ground
I/O2 I/O Line #2
I/O1 I/O Line #1
GND Ground
I/O0 I/O Line #0
GND Ground
+12 +12Vdc Input
ITS Inductive-load
Transient
I/O8 I/O Line #8
GND Ground
I/O9 I/O Line #9
I/O10 I/O Line #10
GND Ground
I/O11 I/O LIne #11
I/O12 I/O Line #12
GND Ground
I/O13 I/O LIne #13
I/O14 I/O Line #14
GND Ground
1
2
3
4
5
6
7
8
9
10
11
12
13
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
I/O #15
I/O #14
I/O #13
I/O #12
I/O #11
I/O #10
Unused.
I/O #9
I/O #8
I/O #7
I/O #6
I/O #5
14
15
16
17
18
19
20
21
22
23
24
25
Unused.
Unused.
Unused.
Unused.
Unused.
Ground
+12Vdc Input
I/O #0
I/O #1
I/O #2
I/O #3
I/O #4
I/O15 I/O LIne #15
DBM16
Suppression
The DBM16 module provides buffering and increased power
handling for all the sixteen I/O lines of the SDD16 models. Each of
the I/O lines can be programmed as an input or as an output by
setting a jumper on the board. The DBM16 plugs directly into the
SDD16's DB25S I/O Port connector. Terminal blocks are provided
for all I/O line, power, and ground connections. Refer to Table C.2.
An enclosure for the DBM16 is available.
DBM16 Interfacing
This section will show some general examples of how to
interface the DBM16 I/O lines to external devices. Caution must be
taken not to exceed the DBM16 specifications, failure to do so could
result in damage to the DBM16 and will void the warranty.
Before connecting the DBM16 to the SDD16 module and
connecting any external device to the DBM16 determine which I/O
lines on the SDD16 module are inputs and which are outputs. Once
the inputs and outputs are known, set the jumpers on the DBM16
accordingly. Refer to Figure C.2.
485SDD16-1005 Manual
Appendix C
C-3
C-4
Appendix C
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Figure C.4 - Solid State Input
Figure C.2 - DBM16 Outline Drawing
Inputs
Digital inputs are used to sense "HIGH" and "LOW" states based
on voltage levels. This is accomplished via switch closures, contact
closures or a solid state digital signals. Each DBM16 input is pulled
up through a resistor and will be read as a logic "1" (HIGH) by the
SDD16 module. When an input on the DBM16 is grounded (below
+1.5Vdc), a logic "0" (LOW) will be read by the SDD16 module.
Figures C.3 - C.6 show examples of some typical input interfaces.
Figure C.5 - Isolated Mechanical Input
Figure C.3 - Switch Input
Figure C.6 - Isolated Solid State Input
485SDD16-1005 Manual
Appendix C
C-5
C-6
Appendix C
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Outputs
Digital outputs are used to turn "ON" or turn "OFF" external
devices. Outputs can be used to control solid state output modules,
logic circuits, and relays. Caution must be taken not to exceed the
power capability of the outputs. Refer to the DBM16 output
specifications.
Setting the SDD16 module's output line to a "1" turns "ON" the
DBM16's output line. Setting the SDD16 module's output line to a
"0" turns "OFF" the DBM16's output driver. The DBM16 outputs are
open collector current sinking drivers. Figures C.7 - C.9 show
examples of some typical output interfaces.
Figure C.9 - Isolated Solid State Output
DBM16 Specifications
I/O Lines
Total:
16 (Factory default - set to inputs)
Inputs
Voltage range:
Low Voltage:
High Voltage:
Internal pull-up current:
0Vdc to +50Vdc
0Vdc to +1.5Vdc
+2.5Vdc to +50Vdc
0.5 ma
Outputs
Figure C.7 - Solid State Output
Output Voltage:
Output current:
+50Vdc max.
350 ma max. - only 1 output on
100 ma max. - all outputs on
50 micro amp max.
Output leakage current:
Output saturation voltage: 1.1Vdc max. @ 100ma
CAUTION: Total output power cannot exceed 2 watts for I/O's #0-
7 and 2 watts for I/O #8-15 @ 25 degrees C.
Power Supply
Input Voltage:
8Vdc to 16Vdc @ 10milliamps
(Doesn't include the power
consumption of external devices.)
Terminal Blocks
Connections:
Size:
0.5" x 2.1" x 4.5"
Figure C.8 - Isolated Mechanical Output
485SDD16-1005 Manual
Appendix C
C-7
C-8
Appendix C
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Figure C.10 - DBM16 Schematic
485SDD16-1005 Manual
Appendix C
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
C-9
C-10
Appendix C
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
With serial communications in a laboratory environment, the
possibility of a communication error occurring is minimal. However,
in a harsh or an industrial environment the possibility increases. A
communication error occurs when a bit transmitted as a “1” is
received as a “0” or vice versa. If the 485SDD16 receives a error in
one or more of the first four command characters (“!0xx”), the unit
will not execute the command. However, if the 485SDD16 receives
an communication error on a data byte (I/O byte for Read Digital
command or state byte for Set Output State command), the
command will be executed since the unit has no way of knowing that
there was an error.
To provide the 485SDD16 with a way of detecting errors in the
data fields, an additional set of commands can be used. This set of
commands begins with the “#” (23h) character, instead of the “!”
(21h) character. Refer to Table D-1. With these commands every
data byte that is transmitted or received is followed by its
complement. For example: To read I/O lines:
Command syntax:
#{addr}RD
Response syntax:
{I/O msb}{~ I/O msb}{I/O lsb} {~ I/O lsb}
Where “~” is used to indicate the “complement of.” If I/O has a
reading of 1, the following would be received:
APPENDIX D
Adding Data Field Comfirmation
{00}{FF}{01}{FE}
Where FFh is the complement of 0 and FEh is the complement of
1. The complement of number “x” can be calculated in QuickBasic
as follows:
comp = (NOT x) AND &HFF
485SDD16-1005 Manual
Appendix D
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
D-1
D-2
Appendix D
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
Table D-1 Extended Commands
Function
Command
Response
Read I/O Lines
#{addr}RD
{I/O msb}{~I/O msb}{I/O
lsb}{~I/O lsb}
Set Output Lines
#{addr}SO{I/O
msb}{~I/O msb}{I/O
lsb}{~I/O lsb}
no response
Set Module
Address
#{addr}SA{new
addr}{~new addr}
no response
no response
no response
Set Turn-around
Delay
#{addr}SC{x}{~x}
Define I/O Lines
#{addr}SD{I/O
msb}{~I/O msb}{I/O
msb}{~I/O msb}
#{addr}SS{I/O
msb}{~I/O msb}{I/O
lsb}{~I/O lsb}
Set Power-up
States
no response
Read
Configuration
#{addr}RC
{I/O msb}{~I/O msb}{I/O
lsb}{~I/O lsb}{I/O powerup
msb states}{~I/O powerup
msb states}{I/O powerup
lsb states}{~I/O powerup
lsb states}{addr}{~addr}{turn-
around delay}{~turn-around
delay}
Where “x” is the required data byte and “~” signifies the complement
of the specified byte.
485SDD16-1005 Manual
Appendix D
D-3
D-4
Appendix D
485SDD16-1005 Manual
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
B&B Electronics -- 707 Dayton Road -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 433-5104
|