Dryer
DC 1560
1 Important safety information
This section includes safety information that will
help protection from risks of personal injuries
or materialistic damages. Failure to follow
these instructions shall cause any warranty and
reliability commitment to become void.
General safety
fuel oil, dry-laundry solvents and other
combustible or explosive materials as
well as the items that are contaminated
or spotted with such materials should not
be dried in the product since they emit
flammable or explosive vapor.
•
Do not dry items cleaned with industrial
chemicals in the dryer.
•
Never place the machine on a carpet-
covered floor, otherwise, lack of airflow
beneath the machine may cause electrical
parts to overheat. This will cause problems
with your machine.
•
•
Do not dry unwashed items in the dryer.
Items soiled with cooking oils, acetone,
alcohol, fuel oil, kerosene, stain remover,
turpentine, paraffin and paraffin removers
must be washed in hot water with plenty of
detergent before being dried in the dryer.
Garments or pillows bolstered with rubber
foam (latex foam), shower bonnets, water
resistant textiles, materials with rubber
reinforcement and rubber foam pads
should not be dried in the dryer.
•
•
If the power cable or mains plug is
damaged, you must call Authorised Service
Agent for repair.
•
The product should not be plugged in
during installation, maintenance and repair
works. Such works should always be made
by the technical service. Manufacturer
shall not be held responsible for damages
arising from processes carried out by
unauthorised persons.
Connect the product to a grounded outlet
protected by a fuse of suitable capacity as
stated in the technical specifications table.
Operate your product at temperatures
between +5°C and +35°C.
Do not use electrical devices in the
product.
•
•
Do not use fabric softeners and anti-static
products unless they are recommended by
the manufacturers of the fabric softener or
the product.
•
This product must be grounded.
Grounding installation decreases the risk of
electric shock by opening a path with low
resistance for the electricity flow in case of
a malfunction or failure. Power cable of this
product is equipped with a conductor and
a grounding plug that allows for grounding
the product. This plug must be installed
appropriately and inserted into a socket
which is grounded in accordance with the
local laws and regulations.
•
•
•
Do not connect the air exit of the product
to the chimney holes which are used for
the exhaust fumes of the devices operating
with gas or other types of fuel.
•
You must provide enough ventilation in
order to prevent gases exiting from devices
operating with other types of fuels including
the naked flame from accumulating in the
room due to the back fire effect.
Always clean the lint filter before or after
each loading.
•
•
Do not install the product behind a door
with a lock, sliding door or a door that has
a hinge against the hinge of the dryer.
Do not install or leave this product in
places where it will be exposed to outdoor
conditions.
•
•
•
Never operate your dryer without the lint
filter installed.
•
•
Do not tamper with the controls.
Do not perform any repair or part replacing
procedures on the product even if you
know or have the ability to perform unless
it is clearly suggested in the operating
instructions or the published service
manual.
Do not allow fibre, dust and dirt
accumulation around the exhaust exit and
at adjacent areas.
Power cable plug must be within easy
reach after installation.
•
•
Do not use extension cords, multi-plugs
or adaptors to connect the dryer to power
supply in order to decrease the risk of
electric shock.
•
•
Inside and exhaust duct of the product
must be cleaned by the qualified service
personnel periodically.
Wrong connection of grounding conductor
of the product can cause electric shock. If
you have any suspect about the grounding
connection, have it checked by a qualified
electrician, service representative or service
personnel.
•
•
Do not make any changes on the plug
supplied with the product. If it is not
compatible with the socket, have a
qualified electrician change the socket with
a suitable one.
Items cleaned or washed with gasoil/
Download from Www.Somanuals.3co-m.EANll Manuals Search And Download.
•
Do not reach into the machine when the
drum is spinning.
Unplug the machine when it is not in use.
Never wash down the appliance with
water! There is the risk of electric shock!
Always disconnect by unplugging from the
mains before cleaning.
are attended by a person who will be
responsible for their safety or who will
instruct them accordingly for use of the
product.
•
•
Children’s safety
•
Electrical appliances are dangerous for
the children. Keep children away from the
machine when it is operating. Do not let
them tamper with the machine.
Packaging materials are dangerous to
children. Keep the packaging materials out
of reach of children or dispose them by
classifying according to waste directives.
Do not allow children sit/climb on or enter
in the product.
Children should be supervised to ensure
that they do not play with the product.
Close the loading door when you leave the
area where the product is located.
•
Never touch the plug with wet hands.
Never unplug by pulling on the cable,
always pull out by grabbing the plug only.
Do not operate the machine if the power
cable or plug is damaged!
•
•
•
Never attempt to repair the machine
yourself, otherwise, you will be putting your
life and others’ lives in danger.
•
•
•
For malfunctions that cannot be solved by
following the information given in the safety
instructions:
Turn off the machine, turn off and contact
an authorised service agent.
•
Do not stop the dryer before the drying
cycle comes to an end unless you will
remove all laundry from the dryer fast in
order to lay them and dissipate the heat.
Remove the door of the drying
•
•
compartment before decommissioning or
disposing of the product.
The final step of the drying cycle (cool-
down cycle) occurs without applying
heat to ensure that the items are left at a
temperature that will not damage them.
Fabric softeners or similar products should
be used as specified by the fabric softener
instructions.
•
•
Underwear that contains metal
reinforcements should not be placed in
a dryer. Damage to the dryer can result if
metal reinforcements come loose during
drying.
•
•
Check all garments for forgotten lighters,
coins, metal pieces, needles, etc. before
loading.
At times when your dryer is not in use or
after the laundry is taken out following the
completion of drying process, turn off by
using the On/Off button. In cases when
the On/Off button is on (while the dryer
is energized), keep the door of the dryer
closed.
Intended use
•
This product has been designed for
domestic use. It should not be used for
other purposes.
•
•
•
Use the product only for drying laundry
that are marked accordingly.
Dry only those articles in your product that
are stated in this manual.
This product is not intended to be used by
persons with physical, sensory or mental
disorders or unlearned or inexperienced
people (including children) unless they
4 - EN
2
Installation
Refer to the nearest Authorised Service Agent
reach 180 kg when they are full. Therefore,
the floor must be capable of carrying the
load on it!
for installation of your product.
CPreparation of location and electrical
installation for the product is under
customer’s responsibility.
Ventilation hose and connection
(for products equipped with an
BInstallation and electrical connections must
be carried out by a qualified personnel.
APrior to installation, visually check if the
product has any defects on it. If so, do not
have it installed. Damaged products will
cause risks for your safety.
outlet vent)
Ventilation hose allows exhaust air from inside
the machine
Vented dryer has 1 air outlet.
Stainless sheet metal or aluminum pipes can
be used instead of a hose. The pipe diameter
should be minimum 10 cm.
Appropriate installation location
Maximum hose and pipe lengths are given in
the table below.
•
Install the product in an environment which
has no risk of freezing and is in a stable
and level position.
Hose
4 m
-1.0 m
-1.8 m
Pipe
•
•
Operate your product in a well ventilated,
dust-free environment.
Maximum length
1 elbow 45°
1 elbow 90°
1 elbow 90° short
1 wall passage
5 m
Do not block the air ducts in front of and
under the product with materials such as
long pile rugs and wooden bands.
Do not place your product on a long pile
rug or on similar surfaces.
-0.3 m
-0.6 m
-2.7 m
-2.0 m
•
•
-2.0 m
Do not install the product behind a door
with a lock, sliding door or a hinged door
which can strike the product.
CEach elbow and other passages should
be subtracted from the maximum length
stated above.
•
Once the product is installed, it should stay
at the same place where its connections
have been made. When installing the
product, make sure that the rear wall of it
does not touch anywhere (tap, socket, etc.)
and also pay attention to install the product
at a place where it will stay permanently.
To connect a ventilation hose;
1. Connect the air outlet hose to the
hose spacer piece by turning it
counterclockwise.
2. Make the hose passages as shown below.
CExhaust of humid air from the dryer into the
room is inconvenient. It may damage the
walls and furniture in the room.
BDo not place the product on top of the
power cable.
•
Keep at least 1.5 cm distance to walls of
other furniture.
CThe ventilation hose can be routed outdoors
via a window or it can be connected to the
air outlet in the bathroom.
CAir outlet hose must be routed directly to the
outdoors. There must be a limited number
of elbows as not to hinder ventilation.
CTo prevent water accumulation in the hose,
make sure that it is not folded on the floor.
Under counter installation
•
A special part (Part no: 295 970 0100)
replacing the top trim must be provided
and installed by the Authorised Service
Agent in order to use the machine under a
counter or in a cupboard. It should never
be operated without the top trim.
•
Leave at least 3 cm of space between
the side and rear walls of the product and
the walls of the counter/cupboard when
installing your product under a counter or in
a cupboard.
Mounting over a washing machine
•
A fitting device should be used between
the two machines when installing above a
washing machine. The bracket (Part no.
296 280 0100 white/296 280 0200 grey)
must be installed by the Authorised Service
Agent.
•
Place the product on a firm floor. If it will be
placed on top of a washing machine, the
approximate weight of both machines may
BThe ventilation hose should not be
connected to the chimney of a stove or a
Download from Www.Somanuals.5co-m.EANll Manuals Search And Download.
fireplace.
BDo not operate your product at the same
time with heaters such as a coal or gas
stove. Airflow may cause the chimney to
flare up.
Connection to water drain (Products
with a condenser);
In products equipped with condenser unit,
water accumulated during the drying cycle
accumulates in the water tank. You should drain
accumulated water after each drying cycle.
You can directly drain accumulated water
through the water drain hose supplied with
the product instead of periodically draining the
water collected in the water tank.
Connecting the water drain hose:
1. Pull the hose out by its end to remove it
from the product. Do not use any tools to
remove the hose. Attach the drain hose
adaptor to the end of this hose.
2. Connect the special drain hose supplied
with the product to the hose adaptor
fitting.
Important:
CThere is no pump in the machine, so ensure
that the hose is placed to allow a easy
water flow.
3. Connect the other end of the drain hose
directly to the wastewater drain or to the
washbasin. The fitting must always be
secured in every type of connection. Your
house may flood if the hose comes out of
its housing during water discharge.
CWhen you direct the water drain to outside,
“Water Tank” warning light will turn on at
the end of each programme.
CThe end of the hose should never be higher
than the level of the water outlet on the
machine. Otherwise, the “tank full” light of
your machine will illuminate and stop the
programme.
CIf the dryer is mounted on the washing
machine by means of a bracket, use of the
water drain hose is recommended. The
drain hose should be directed downwards
as shown in the figure.
Adjusting feet
In order to ensure that your product operates
more silently and vibration-free, it must stand
level and balanced on its feet. Front feet of your
product can be adjusted. Balance the machine
by adjusting the feet.
Important:
•
•
•
The hose should be attached to a height of
maximum 80 cm.
Make sure that the hose is not pinched or
bend.
The end of the hose should not be bent,
it should not be stepped on and it must
not be folded between the drain and the
product.
1. Loosen the feet by hand.
2. Adjust the feet until the product stands level
and firmly on the floor.
Connecting the water drain hose for
models with the water tank at the
bottom;
CDo not use any tools to loosen the
adjustable feet, otherwise, they can be
damaged.
Connection pipe to water drain is at the bottom
rear of your machine.
CNever remove the adjustable feet from their
housings.
1. Remove the bracket and the rubber cap.
2. Attach the drain hose and replace the
bracket to its position.
2 plastic pieces supplied along with the user
manual prevent your machine from slipping on
6 - EN
wet and slippery surfaces. To install the plastic
parts:
First use
•
To have the product ready for operation
1. Tilt your product to backwards.
2. Fit the plastic parts on to the front
adjustable feet. Press on the plastic parts
to snap them into their seating.
3. Check the balance of your product
again and readjust the adjustable feet if
necessary.
before calling the authorised service agent,
make sure that its location and power
supply installations are appropriate. If they
are not, call a qualified electrician to have
any necessary arrangements carried out.
Make sure that the power connections of
the product are in accordance with the
instructions given in relevant chapters of
this manual.
•
Electrical connection
Connect the machine to a grounded outlet
protected by a fuse of suitable capacity as
stated in the technical specifications table. Our
company shall not be liable for any damages
that will arise when the machine is used on a
circuit without grounding.
Disposing of packaging material
Packaging materials are dangerous to children.
Keep packaging materials in a safe place out
of reach of children. Packaging materials of
your product are manufactured from recyclable
materials. Sort and dispose of them in
accordance with recycled waste instructions.
Do not dispose of them with normal domestic
waste.
•
Connection must comply with national
regulations.
•
If the current value of the fuse or breaker
in the house is less than 16 Amps, have a
qualified electrician install a 16 Amp fuse.
Power cable plug must be within easy
reach after installation.
Transportation of the machine
1. Unplug the machine from the mains.
2. Remove the water drain (if any) and
chimney connections.
3. Drain water remained in the machine
completely before transportation.
•
•
The voltage and allowed fuse or breaker
protection are specified in the “Technical
Specifications” section.
•
•
•
The specified voltage must be equal to
your mains voltage.
Disposing of the old machine
Dispose of your old machine in an
environmentally friendly manner.
Refer to your local dealer or solid waste
collection centre in your area to learn how to
dispose of your machine.
Before disposing of your old machine, cut off
the power cable plug and make the loading
door lock unusable to avoid dangerous
conditions to children.
Do not make connections via extension
cables or multi-plugs.
The main fuse and switches must have a
contact distance of minimum 3 mm.
BDamaged power cable must only be
replaced by a qualified electrician.
BIf the product is faulty, it must not be
operated unless it is repaired! There is the
risk of electric shock!
Technical Specifications
EN
2
Height (adjustable)
Width
85.0 cm
59.5 cm
54 cm
6 kg
Depth
Capacity (max.)
Weight (net)
37 kg
Voltage
Rated power input
Model code
See type label
Type label is located behind the loading door.
Download from Www.Somanuals.7co-m.EANll Manuals Search And Download.
3 Initial preparations for drying
Things to be done for energy saving:
• Make sure that you operate the product
at its full capacity but pay attention to
not exceeding it.
• Spin your laundry at the highest speed
possible when washing them. Thus,
the drying time is shortened and energy
consumption is decreased.
• Pay attention to dry same types of
laundry together.
A B C D
Low
l n m
o p q
• Follow the instructions in the user
manual for programme selection.
• Make sure that sufficient clearance
is provided at the front and rear side
of the dryer for air circulation. Do not
block the grill at the front side of the
product.
• Do not open the door of the machine
during drying unless necessary. If you
must certainly open the door, pay
Laundry unsuitable for drying in the
attention not to keep it open for a long
time.
machine
• Do not add new (wet) laundry during
drying.
• Laundry items with metal attachments
such as belt buckles and metal buttons
can damage your dryer.
• Lint and fibres released from the
laundry to the air during the drying
cycle are collected in the “Lint Filter”.
Make sure that you clean the filters
before or after each drying.
• Do not dry items such as woollens, silk
garments and nylon stockings, delicate
embroidered fabrics, laundry with metal
accessories and items such as sleeping
bags in the dryer.
• In models with condenser, make sure
that you clean the condenser regularly
at least once every month or after every
15 drying cycles.
• In vented models, follow the chimney
connection rules in the user manual
and pay attention to the chimney
cleaning.
• Ventilate the room, where the dryer is
located, well during drying.
• “For power saving in models with lamps, at
times when your dryer is not in use, keep
the door closed if the On/Off button is
pressed (if the dryer is energized).”
• Laundry made of delicate and valuable
fabrics as well as lace curtains can be
creased. Do not dry them in the dryer!
• Do not dry items made of hermetic
fibres such as pillows and quilts in the
dryer.
• Laundry made of foam or rubber will be
deformed.
• Do not dry laundry containing rubber in
the dryer.
• Do not dry laundry exposed to
petroleum, oil, combustible or explosive
agents in the dryer even if they are
washed beforehand.
• Overly wet laundry or laundry with
dripping water must not be put into the
dryer.
• Items cleaned or washed with gasoil/
fuel oil, dry-laundry solvents and other
combustible or explosive materials as
well as the items that are contaminated
or spotted with such materials should
Laundry suitable for drying in the machine
C Always follow the suggestions on the
laundry labels. Dry only the laundry
having a label stating that they are
suitable for drying in a dryer and make
sure that you select the appropriate
programme.
8 - EN
not be dried in the product since they
emit flammable or explosive vapor.
Do not dry items cleaned with industrial
chemicals in the dryer.
A Consider the information in the
"Programme Selection Table". Always
start the programme in accordance
with the maximum load capacity.
C Adding laundry to the machine more
than the level shown in the figure is not
recommended. Drying performance
will degrade when the machine is
overloaded. Furthermore, your dryer
and your laundry can be damaged.
C Place your laundry into the drum
loosely so that they will not get tangled.
CLarge pieces (E.g.: bed sheets, quilt
covers, large tablecloths) may bunch-
up. Stop the dryer 1-2 times during
drying process to separate bunched-up
laundry.
•
•
•
Do not dry your unwashed laundry in the
dryer.
Items soiled with cooking oils, acetone,
alcohol, fuel oil, kerosene, stain remover,
turpentine, paraffin and paraffin removers
must be washed in hot water with plenty of
detergent before being dried in the dryer.
Garments or pillows bolstered with rubber
foam (latex foam), shower bonnets, water
resistant textiles, materials with rubber
reinforcement and rubber foam pads
should not be dried in the dryer.
Do not use fabric softeners and anti-static
products unless they are recommended by
the manufacturers of the fabric softener or
the product.
•
•
•
Following weights are given as examples.
Do not dry the underwear reinforced with
metal parts in the dryer. If these metal
reinforcements loosen and break during
drying, they will damage your dryer.
Approximate
weights (g)
Home articles
Cotton quit covers (double)
Cotton quit covers (single)
Bed sheets (double)
Bed sheets (single)
Large tablecloths
Small tablecloths
Tea napkins
1500
1000
500
350
700
250
100
700
350
Preparing laundry for drying
• Check all laundry items before loading
them into the product to make sure that
there are no lighters, coins, metal items,
needles and etc. in their pockets or on
any part of them.
• Fabric softeners and similar products
must be used in accordance with the
instructions of the manufacturer of the
relevant products.
• All laundry must be spun at the highest
spin speed that your washing machine
allows for the laundry type.
• Laundry may be tangled after washing.
Separate your laundry before placing
them into your dryer.
• Sort your laundry according to their
types and thicknesses. Dry the same
type of laundry together. E.g.: fine
kitchen towels and table cloths dry
faster than the thick bath towels.
Correct load capacity
Bath towels
Hand towels
Approximate
weights (g)
Garments
Blouses
Cotton shirts
Shirts
Cotton dresses
Dresses
Jeans
150
300
200
500
350
700
100
125
Handkerchiefs (10 pieces)
T-Shirts
Loading
•
•
•
Open the loading door.
Place laundry items loosely into the dryer.
Push the loading door to close. Ensure that
no items are caught in the door.
Download from Www.Somanuals.9co-m.EANll Manuals Search And Download.
4 Selecting a Program and OperatingYour Machine
Control panel
1
2
3
4
6
5
7
1. Filter cleaning warning light
6. Start/Pause/Cancel button
Warning light turns on when the filter is full.
2. Program follow-up indicator
Used to follow-up the progress of the
current programme.
Used to start, pause or cancel the
programme.
7. Water tank warning light*
Warning light turns on when the water tank
is full.
8.Time delay selection button*
Used to set the time delay.
3. Cancel audio warning
Used to cancel the audio warning given at
the end of the programme.
4. On/Off button
Used to turn on and off the machine.
5. Programme selection knob
Used to select a programme.
* It may change according to the specifications
of your dryer
Drying
Cottons
Synthetics Delicates
Timer
program
Ventilation
End
/Anti-
creasing
Ready to Extra Ready Ready to
Iron
to Wear
Wear
Timer
follow-up
indicator
Low
temparature temparature Audio
select Warning
Low
Cancel
Spin
On/Off Start/Pause/
Cancel
Filter
cleaning
Tank
full
Child-proof
lock
10 - EN
laundry from creasing will be activated if you
do not take the laundry out after the program
has come to an end. This program rotates
the laundry in 10 minutes intervals to prevent
creasing.
Preparing the machine
1. Plug in your machine.
2. Place the laundry in the machine.
3. Press the “On/Off” button.
C Pressing the “On/Off” button does not
necessarily mean that the programme has
started. Press "Start/Pause/Cancel" button
of the machine to start the programme.
Program selection
Special programs
For special cases, there are also extra programs
available:
C Additional programs may differ according
to the model of your machine.
Decide the appropriate program from the table
below which includes drying temperature in
degrees. Select the desired program with the
program selection button.
Delicates
You can dry at a lower temperature your very
delicate laundry (silk blouses, fine underwear,
etc.) that are suitable for drying or laundry which
is advised to be hand-washed.
C It is recommended to use a cloth bag
to avoid certain delicate garments and
laundry from getting creased or damaged.
Take your garments immediately out of the
dryer and hang them after the programme
ends in order to prevent them being
creased.
Dry at high temperature
only for cotton laundry.
Thick and multi layered
laundry (E.g.: towels,
linens, jeans) are dried in
a way that they do not
require ironing before
placing in the wardrobe.
Extra dry
•Ventilation
Only ventilation is performed for 10 minutes
without blowing hot air. You can air your clothes
that have been kept at closed environments for
a long time thanks to this program to deodorize
unpleasant odors.
Normal laundry (E.g.:
tablecloths, underwear)
are dried in a way that
they do not require ironing
before placing in the
drawers.
•Timer programs
Ready to Wear
Ready to Iron
You can select one of the 10 min., 20 min., 40
min. and 60 min. timer programs to achieve the
desired final drying level at low temperatures.
Program dries at the selected time regardless of
the drying level.
Normal laundry (E.g.,
Shirts, dresses) are dried
ready to be ironed.
C For further program details, see, “Program
Selection Table”
Main programs
Depending on the type of textile, the following
main programs are available:
•Cottons
You can dry your durable clothes with this
program. Dries at a higher temperature. It is
recommended to use for your cotton items
(such as bed sheets, quilt cover, underclothing,
etc.).
•Synthetics
You can dry your less durable clothes with
this program. It dries at a lower temperature
compared to the cottons program. It is
recommended for your synthetic clothes (such
as shirts, blouses, synthetic/cotton blended
garments, etc.).
C Do not dry curtains and lace in your
machine.
•Anti-creasing
A 2-hour anti creasing program to prevent
11 - EN
Program selection and consumption table
EN
2
Program table
Approximate
amount of
remaining
humidity
Capacity Spin speed in washing
Drying time
(minutes)
Programs
(kg)
machine (rpm)
Cottons / Coloreds
1200-1000
900-800
% 60
% 70
% 60
% 70
% 60
% 70
% 60
% 70
130
150
6
3
6
3
Ready to Wear
A
1200-1000
900-800
80-60
100-80
130-100
130
1200-1000
900-800
Ready to Iron
A
1200-1000
900-800
80-60
80-60
Synthetics
800
600
800
600
% 40
% 50
% 40
% 50
80-60
130-100
60-30
3
Ready to Wear
B
1.5
60-30
Delicates
Ready to Wear
1.5
600
% 50
40
B
Energy consumption values
Approximate
amount of
remaining
humidity
Energy
consumption
value kWh
Capacity Spin speed in washing
Programs
(kg)
machine (rpm)
Cottons linen Ready to wear*
Cottons Ready to iron
6
6
3
1000
1000
600
% 60
% 60
%50
3.84
3.40
1.60
Synthetics Ready to wear
* : Energy Label standard program (EN 61121:2005)
All values given in the table have been fixed according to EN 61121:2005 Standard. These values
may deviate from the table according to the laundry type, laundry spin speed, environmental
conditions and voltage fluctuations.
12 - EN
Auxiliary function
Changing the program after the
program has started
Buzzer Cancel Models Equiped
Your machine will send out an buzzer warning
when the program comes to an end. If you
do not want to hear this buzzing, you need to
press the “Cancel Audio Warning” button. The
relevant LED will light up when this button is
pressed and an audio warning will not be given
when the program comes to an end.
Warning indicators
You can use this feature to dry your clothes
under higher or lower temperatures after your
dryer has started.
For example;
1. Press and hold the “Start/Pause/Cancel”
button for about 3 seconds to “Cancel”
the programme in order to select “Extra
Dry” programme instead of “Iron Dry”
programme.
C Warning indicators may differ according to
the model of your machine.
Filter cleaning
2. Select the “Extra Dry” programme by
rotating the programme selection button.
3. Press “Start/Pause/Cancel” button to start
the programme.
A warning LED will light up to remind filter
cleaning after the program finishes.
C If the filter cleaning warning LED lights up
continuously, please refer to, “Solution
suggestions for problems”.
C Press "Start/Pause/Cancel" button for
3 seconds to cancel the programme or
turn the programme selection knob in any
direction to end the programme while the
machine is running. Water tank and filter
cleaning warning lights turn on to warn the
user when the programme is cancelled by
pressing the "Start/Pause/Cancel" button
for 3 seconds. However, the warning
lights do not turn on when the programme
is cancelled by turning the programme
selection knob. Only the drying light turns
on and the machine remains in hold until
a new programme is selected and the
"Start/Pause/Cancel" button is pressed.
Child-proof lock of the machine should not
be active in order to perform these two
operations. If the child-proof lock is active,
deactivate it before performing these
operations.
Water tank
Warning light starts flashing when the tank is
filled with water. The dryer stops operating if
the warning light turns on when a programme
is running. Drain the water in the water tank
to restart the dryer. Press “Start/Pause/
Cancel” button to start the programme after
you have emptied the water tank. The warning
light turns off and the programme resumes
operating.
Starting the programme
1. Press “Start/Pause/Cancel” button to start
the programme.
2. Light of the “Start/Pause/Cancel” button
will turn on to indicate that the programme
has started.
Progress of program
Progress of a running program is shown
through the program follow-up indicator.
At the beginning of every program step, the
relevant indicator LED will light up and light of
the completed step will turn off.
“Drying”:
Adding/removing laundry in standby mode
In order to add or remove laundry after the
programme starts:
1. Press the “Start/Pause/Cancel” button to
switch the dryer to “Pause” mode. Drying
process will stop.
- Drying level will be illuminated during the whole
drying process until the drying degree reaches “
Ready to Iron “.
2. Open the door at “Pause” position and
close it again after adding or taking out
laundry.
“ Ready to Iron “:
3. Press “Start/Pause/Cancel” button to start
- Starts to illuminate when the drying degree
reaches “ Ready to Iron “ step and remains
illuminated until the next step.
the programme.
C Any laundry added after the drying process
has started may cause the dried clothes in
the machine intermingle with wet clothes
and the result will be wet laundry after the
drying process is over.
“ Ready to Wear “:
- Starts to illuminate when the drying degree
reaches “ Ready to Iron “ step and remains
illuminated until the next step.
C Laundry may be added or taken out
“Final / Anti-creasing”:
as much as desired during a drying
- Illuminates when the program comes to an
end and anti-creasing function is activated.
C If more than one LED light up or
flash concurrently, it means there is
malfunctioning or a failure (please see,
Solution suggestions for problems).
13 - EN
process, but this process will extend the
programme duration and increase energy
consumption since the drying will be
interrupted continuously. Therefore, it is
recommended to add laundry before the
drying programme has started.
3 seconds. The “Filter cleaning”, “Water tank”
and “End/ Anti-creasing” warning lights will
turn on at the end of this period for reminding
purposes.
AAs the inside of the dryer will be excessively
hot when you cancel the programme while
the dryer is running, activate the ventilation
programme to cool it down.
Child-proof lock
There is a childproof lock to prevent any program
interruption due to the pressing of keys while
the program is on. The loading door and all
keys except the “On/Off” key on the panel
are deactivated when the child-proof lock is
active.
In order to activate the childproof lock, press
on the “Start/Pause/Cancel” and “Cancel audio
warning” buttons simultaneously for 3 seconds.
To start a new program after the program is
over or to interrupt the program, the childproof
lock should be deactivated. To deactivate the
childproof lock, press the same buttons for 3 sec.
C Child-proof lock is deactivated when the
machine is restarted by pressing the On/Off
button.
End of program
The “End/Anti-creasing”, “Filter cleaning” and
“Water tank” warning lights on the programme
follow up indicator will turn on when the
programme comes to an end. The door can be
opened and the machine becomes ready for a
second cycle.
Press “On/Off” button to turn off the dryer.
C Final step of the drying cycle (cooling step)
is performed without heat application in
order to keep the items at a temperature
that would not harm them.
C A 2-hour anti creasing programme to
prevent laundry from creasing will be
activated if you do not take the laundry out
after the programme has come to an end.
C If you will not take the laundry out
immediately, do not stop the dryer before
the drying process is complete.
C Clean the filter after each drying (please
see, Filter cleaning).
C Drain the water tank after each drying
(please see, Water tank)
C Press the relevant buttons for 3 seconds
to activate the child-proof lock. A long
beep will be heard and the child-proof lock
will be activated. A double beep will be
heard if you press any button or turn the
programme selection knob while the child-
proof lock is active. Press the buttons for 3
seconds to deactivate the child-proof lock.
Single beep will be heard and child-proof
lock will be deactivated.
AA double beep will be heard if you turn
the programme selection knob when the
machine is running and the child-proof
lock is active. If you deactivate the child-
proof lock without returning the program
selection knob to its previous position,
the programme will be terminated since
the position of the programme selection
knob is changed. The drying LED turns on
and the machine remains on hold until a
new programme is selected and the Start
button is pressed.
Ending the program through canceling
A new programme can be selected and
started after “Programme cancel” is activated
in order to change the drying programme.
To cancel any selected programme:
Press “Start/Pause/Cancel” button for about
14 - EN
5 Maintenance and cleaning
since these materials can cause fire and
explosion!
Cover filter
Lint and fibres released from the laundry to the
air during the drying cycle are collected in the
“Cover Filter”.
Water tank (Products equipped with a
condenser);
The moisture in the damp laundry is taken from
the laundry and condensed. Drain the water
tank after each drying cycle or during drying
when “Water tank” warning light turns on.
CYou can use the water in the water tank in
your steam irons or air humidifiers.
ACondensed water is not drinkable!
ANever take out the water tank when the
programme is running!
CSuch fibre and lint are generally formed
during wearing and washing.
Water tank may be located in two different
places as indicated below, depending on the
model of your dryer.
CAlways clean the filter after each drying
process.
-
-
Inside the drawer on the panel
Behind the kick plate cover
CYou can clean the filter and filter area by
vacuum cleaner.
If you forget to drain the water tank, your dryer
will stop during the following drying cycles
when the water tank is full and the “Water
tank” warning light will turn on. If this is the
case, press the “Start/Pause/Cancel” button to
resume the drying cycle after draining the water
tank.
To clean the filter:
1. Open the loading door.
2. Remove the cover filter by pulling it up and
open the filter.
3. Clean lint, fibre, and cotton raveling by
hand or with a soft piece of cloth.
4. Close the filter and place it back into its
seat.
CClogging may arise on the filter surface after
using your machine for some time; if this
occurs, wash the filter with water and dry it
before using again.
Sensor (models with a sensor)
There are humidity sensors in your dryer that
detect whether the laundry is dry or not.
To drain the water tank:
1. Carefully remove the water tank by
opening the kick plate cover/pulling the
drawer.
2. Drain the water by opening the water tank
cover.
3. If there is lint accumulation in the water
tank cover, clean it and press to close.
4. Place the water tank into its seat.
For the condenser (products with a
condenser)
Hot and humid air in the condenser is cooled
with the cold air from the room. Thus, the
humid air circulating in your dryer is condensed
and then pumped into the tank.
CClean the condenser after every 15 drying
cycles or once a month.
To clean the sensor:
1. Open the loading door of the dryer.
2. Allow the machine to cool down if drying
has been carried out.
To clean the condenser:
1. If a drying process has been carried out,
open the door of the product and wait until
it cools down.
3. Wipe the metal sensors with a soft cloth,
dampened with vinegar and dry them.
CClean metal sensors 4 times a year.
ANever use solvents, cleaning agents
or similar substances when cleaning
2. Unlock the 4 condenser locks after
opening the kick plate.
3. Pull out the condenser.
15 - EN
4. Clean the condenser with pressurized
water and wait until the water drains.
5. Replace the condenser with the side of it
labelled with “Top” facing upwards. Lock
the 4 condenser locks. Make sure that
the red lock on the upper right corner is
engaged securely.
6. Close the kick plate cover.
Close properly and
check the locking
latchs?
16 - EN
6
Solution suggestions for problems
Drying process takes too much time
•
Meshes of the filter may be clogged. Wash with water.
Laundry come out wet at the end of drying.
•
•
Meshes of the filter may be clogged. Wash with water.
Excessive laundry might have been loaded in. Do not overload the machine.
Machine does not switch on or the program does not start. Machine is not activated when set.
•
•
•
It might have not been plugged in. Make sure that the machine is plugged in.
The loading door may be ajar. Make sure that the loading door is properly closed.
Program might have not been set or the «Start/Pause/Cancel» button might have not been
pressed. Make sure that the program has been set and it is not in “Pause” mode.
«Childproof lock» might have been activated. Deactivate the childproof lock.
The condenser cover on the models with a condenser might not be closed securely. Make
sure that the condenser cover and the red lock is closed securely.
•
•
Program has been interrupted without any cause.
•
•
•
The loading door may be ajar. Make sure that the loading door is properly closed.
Electricity may be cut off. Press «Start/Pause/Cancel» button to start the program.
The condenser cover on the models with a condenser might not be closed securely. Make
sure that the condenser cover and the red lock is closed securely.
Laundry has shrunk, become felted or deteriorated.
•
A program suitable for the laundry type might have not been used. Dry only the laundry
which is suitable for drying in your machine after checking the labels on your clothes.
Select a program with suitable low temperature for the laundry type to dry your clothes.
•
Drum lightning does not come on. (for models equipped with a lamp)
•
The machine might have not been started by using the On/Off button. Make sure that the
machine is On.
•
•
Bulb may have blown. Call the authorized service to replace the bulb.
The condenser cover on the models with a condenser might not be closed securely. Make
sure that the condenser cover and the red lock is closed securely.
2 beeps heard when the buttons are pressed or the program selection knob is turned.
•
•
Childproof lock» might have been activated. Deactivate the childproof lock.
Program selection knob might be turned to an undefined position. Select one of the
defined programs.
“Filter cleaning” light is flashing.
Filter might have not been cleaned. Clean the cover filter.
“Final / Anti-creasing” LED is on.
Program has come to an end. Turn off the machine and take out the laundry.
3 beeps are heard when you press the Start/Pause/Cancel button
•
•
•
•
The loading door may be ajar. Make sure that the machine is plugged in.
Make sure that the condenser cover and the red lock is closed securely.
Also for products equipped with a condenser:
“Water tank” warning LED is flashing.
•
•
Water may be full.
Drain the water in the water tank.
ACall an authorised service agent if the problem persists.
17 - EN
|