Fridge Freezer
CT5381APW
1 Your refrigerator
2 Warnings
Electrical Requirements .....................5
Warning! This Appliance Must Be
3
4
5 Using your refrigerator 14
FREEZING FRESH FOOD................14
DEFROSTING..................................15
A) FRIDGE COMPARTMENT ...........15
B) FREEZER COMPARTMENT.........15
Earthed .............................................5
Energy Saving Tips............................6 6 Maintenance and
cleaning
16
17
3 Installation
7
TRANSPORTATION INSTRUCTIONS.7
INSTALLATION INSTRUCTIONS........8
Replacing the interior light bulb .........9
REVERSING THE DOORS...............10
7 Do's and Don'ts
4 Before operating
13
Final Check .....................................13
EN
2
1 Your refrigerator
Congratulations on your choice of a BEKO quality Appliance which has been
designed to give you service for many years.
1
2
3
11
12
4
6
5
6
7
12
13
8
9
10
1. Freezer compartment
2. Ice cube tray
3. Interior light
4. Thermostat control
5. Fridge compartment shelves
6. Adjustable shelves
7. Defrost water collection channel-Drain tube
8. Salad crisper cover
9. Salad crisper
10. Adjustable front feet
11. Egg tray
12 .Door shelf
13. Bottle shelf
CFigures that take place in this instruction manual are schematic and may not
correspond exactly with your product. If the subject parts are not included in the
product you have purchased, then it is valid for other models.
EN
3
2 Warnings
•
To obtain the best possible
• Do not connect your appliance to
the electricity supply until all packing
and transit protectors have been
removed.
• If transported horizontally leave to
stand upright for at least 4 hours before
switching on to allow compressor oil to
settle
performance and trouble free operation
from your appliance it is very important
to carefully read these instructions.
• On delivery, check to make sure that
the product is not damaged and that all
the parts and accessories are in perfect
condition.
• Ensure that the plug remains readily
accessible. Do not use multiple adapter
or extension cable.
• Failure to observe these instructions
may invalidate your right to free service
during the guarantee period.
• Keep ventilation openings, in the
appliance enclosure or in the built-in
structure, clear of obstruction.
• If you are discarding an old
refrigerator with a lock or latch fitted to
the door, disable the lock/latch, ensure
that it is left in a safe condition to prevent
the entrapment of young children.
• This fridge/freezer must only be
used for its intended purpose i.e the
storing and freezing of edible foodstuff.
• Do not dispose of the appliance on
a fire. At BEKO, the care and protection
of our environment is an ongoing
commitment. This appliance which
is among the latest range introduced
is particularly environment friendly.
Your appliance contains non CFC /
HFC natural substances in the cooling
system (Called R600a) and in the
insulation (Called cyclopentane) which
are potentially flammable if exposed
to fire. Therefore, take care not to
damage, the cooling circuit / pipes of
the appliance in transportation and in
use. In case of damage do not expose
the appliance to fire or potential ignition
source and immediately ventilate the
room where the appliance is situated.
• We suggest you contact your local
authority for disposal information and
facilities available.
•
Do not use mechanical devices
or other means to accelerate the
defrosting process, other than those
recommended by the manufacturer.
• Do not damage the refrigerant
circuit.
• Do not use electrical appliances
inside the food storage compartments
of the appliance, unless they are
of the type recommended by the
manufacturer.
• We suggest you keep these
instructions in a safe place for easy
reference.
• This appliance is not intended for
use by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
• See Installation Instructions on
on page 8 for information on suitable
location.
EN
4
• Children should be supervised to
Colour of the replacement fuse cover
ensure that they do not play with the must be the same colour as that visible
appliance.
on the pin face of the plug. Fuse covers
are available from any good electrical
store.
Electrical Requirements
Before you insert the plug into the
wall socket make sure that the voltage
and the frequency shown on the rating
plate inside the appliance corresponds
to yourelectricity supply.
Important! Fitting A Different Plug
As the colours of the wires in the
mains lead of this appliance may not
correspond with the coloured markings
identifying the terminals in your plug
proceed as follows: (See diagram).
1. Connect the green-yellow or green
(Earth) wire to the terminal in the plug
Rating label is on the left hand side of
fridge inner liner.
We recommend that this appliance be
connected to the mains supply via a
suitable switched and fused socket.
The appliance must be positioned so
that the plug is accessible.
Should the mains lead of the appliance
become damaged or should it need
replacing at any time, it must be
replaced by a special purpose made
mains lead which can only be obtained
from a BEKO Authorised Service
Agent.
marked ‘E’ or with the symbol
or
coloured green and yellow or green.
2. Connect the blue (Neutral) wire to
the terminal in the plug marked ‘N’ or
coloured black.
3. Connect the brown (Live) wire to
the terminal in the plug marked ‘L’ or
coloured red.
With alternative plugs a 13 A fuse must
be fitted either in the plug or adaptor or
in the main fuse box. If in doubt contact
a qualified electrician.
Warning! This Appliance
Must Be Earthed
If the fitted moulded plug is not suitable
for your socket, then the plug should be
cut off and an appropriate plug fitted.
Destroy the old plug which is cut off as
a plug with bared cord could cause a
shock hazard if inserted into a socket
elsewhere in the house.
6mm.
GREEN &
YELLOW
OR
GREEN
L
BROWN
OR
RED
N
22mm.
BLUE
OR
The moulded plug on this appliance
incorporates a 13 A fuse. Should the
fuse need to be replaced an ASTABEAB
approved BS 1362 fuse of the same
rating must be used. Do not forget
to refit the fuse cover. In the event of
losing the fuse cover the plug must not
be used until a replacement fuse cover
has been fitted.
BLACK
CORD GRIP
EN
5
Energy Saving Tips
1- Ensure your appliance is installed
in a well ventilated area.
2- Ensure the time between buying
chilled/frozen food and placing them
in your appliance is kept at minimum,
particularly in summer. We recommend
you use a cool bag or a special carrier
bag to carry perishable food.
3- Do not leave the door (s) of your
appliance open longer than necessary
and ensure they are closed properly
after each opening.
4- Defrost frozen food in the fridge
compartment, so that frozen food acts
as an ice pack to assist cooling in the
fridge.
EN
6
3 Installation
IMPORTANT : Care must be taken
while cleaning / carrying the appliance
to avoid touching the bottom of the
condenser metal wires at the back of
the appliance as you might injure your
fingers and hands.
Do not attempt to sit or stand on top
of your appliance as it is not designed
for such use. You could injure yourself
or damage the appliance.
“IMPORTANT: Make sure that mains
cable is not caught under the appliance
during and after carrying / moving the
appliance, to avoid the mains cable
becoming cut or damaged.”Do not
allow children to play with the appliance
or tamper with the controls.
“IMPORTANT:This appliance is
not designed for stacking with any
otherappliance.When positioning your
appliance, take care not to damage
your flooring, pipes,wall coverings etc.
BEKO declines to accept any liability
should the instructions not be followed.
TRANSPORTATION
INSTRUCTIONS
1. The appliance should be
transported only in a vertical upright
position. The packing as supplied must
be intact during transportation.
2. If during the course of transport
the appliance has to be transported
horizontally, it must only be laid on its
right hand side when standing in the
front of the appliance. After bringing
it to upright position,it must not be
operated for at least 4 hours to allow
the system to settle.
3. Failure to comply with the
above instructions could result in
damage occuring to the appliance.
The manufacturer will not be held
responsible if these instructions are
disregarded.
4. The appliance must be protected
against rain, moisture and other
atmospheric influences.
5. When positioning your appliance
take care not to damage your flooring,
pipes, wall coverings etc. Do not move
the appliance by pulling by the door or
handle.
6. Empty any water in the drain tray
before moving. See section ‘Defrosting’
and ‘Care & cleaning’ for further
information.
EN
7
INSTALLATION
INSTRUCTIONS
1.The space in the room where the
appliance is installed must not be
smaller than 10 cubic metres.
2.Do not put your fridge freezer in a
cold room where the temperature is
likely to go below +5 degrees C (41
degrees F) during night time and/or
especially in winter.
3.Thisfridgefreezerhasbeendesigned
to operate in ambient temperatures
between +5 and +32 degrees C (41
and 90 degrees F) Therefore if the
appliance is installed in an unheated/
cold room (eg: conservatory/annex/
shed/garage etc) then the appliance
will not operate causing the freezer
compartment to run warmer and as a
result the storage time of frozen food
may be reduced.
4.Do not place the appliance near
cookers, radiators or in direct sunlight
as this will cause your appliance to
work harder. If installed next to a
source of heat or freezer, maintain
the following minimum side clearances:
6.The fridge/freezer should be located
on a smooth surface. The two front
feet
can be adjusted as required. To
ensure that your appliance is standing
upright adjust the two front feet by
turning clockwise or anti-clockwise,
until the product is in firm contact with
the floor. Correct adjustment of feet
avoids excessive vibration and noise.
7.Refer to cleaning and care section
to prepare your appliance for use.
8.A special receptacle is supplied to
store the mains plug during transit.
The receptacle is fixed at the back of
the cabinet, on the left hand side of
the compressor. (See diagram) Gently
remove the plug from the receptacle.
Never pull the mains cord, you may
damage the appliance. In the case of
transportation,ensure you locate the
plug in the receptacle provided to avoid
transit damage.
From Cookers
From Radiators
From Freezers
50 mm (2”)
300 mm (12”)
25 mm (1”)
5.Make sure that sufficient room
is provided around the appliance to
ensure free air circulation.Fit the two
plastic wall spacers supplied with the
appliance onto the condenser at the
back of the appliance by rotating 1/4
turn (See Diagram).
EN
8
Replacing the interior light
bulb
Should the light fail to work switch
off at the socket outlet and pull out
the mains plug. Follow the below
instructions to check if the light bulb
has worked itself loose.
If the light still fails to work obtain
a replacement E14 screw cap type
15 Watt (Max) bulb from your local
electrical store and then fit it as follows:
1. Switch off at the socket outlet and
pull out the mains plug. You may find
it useful to remove shelves for easy
access.
2. Remove the light diffuser cover as
shown in figure (a-b).
3. Replace the burnt-out light bulb.
4. Reassemble the light diffuser cover
as shown in figure (c).
“Push firmly to ensure cover is fitted
properly.”
5. Carefully dispose of the burnt-out
light bulb immediately.
“Replacement light bulb can easily be
obtained from a good local electrical or
DIY store.”
EN
9
2.Remove all loose items and fittings
and food, if any, from inside the
appliance and door racks.
3.Gently prise off plastic hinge cover
of upper door top trim using a small
flat-headed screwdriver. (1)
REVERSING THE DOORS
We recommend that you reverse
doors before switching on for the first
time.
Tools required: Small and medium size
flat and cross-headed screwdrivers, a
pair of pliers.
4.Gently tilt the appliance back against
a strong wall on its rear side sufficiently
to allow the lower hinge to be removed.
Take care to protect the appliance, your
wall and floor coverings. You can utilise
the original packaging to do this. Once
you tilt the appliance back, check to
make sure the appliance is completely
stable and safe before you carry on. (2)
5.Unscrew and remove the lower
hinge using a cross-headed screwdriver
while holding the lower door firmly.(3)
6.Remove lower door carefully off the
middle hinge and stand door upright in
a safe place.(4)
Spare Parts supplied in the plastic
bag: The following parts, which are
exclusively for left hand side fitted hinge
operation are supplied in a plastic bag
with the appliance:
- Upper door top trim hinge covers –
there are 2 different parts, one for each
side of top trim.
- Upper door middle hinge bushing/
door stopper assembly.
7.Open upper door and unscrew and
remove the middle hinge while holding
the upper door firmly. Use a flat-headed
screwdriver. Middle hinge will need to
be rotated 180 degrees before re-fitting
on the opposite side.(5)
We suggest you keep all the parts
supplied in the plastic bag and also
parts, which have been removed when
reversing doors, in a safe place for
possible future, re-use.
8.Remove upper door carefully off the
upper hinge and stand door upright in
a safe place.(6)
9.Unscrew and remove the upper
hinge using a flat-headed screwdriver.
(7)
10.Rotate the upper hinge 180
degrees and then unscrew and remove
the hinge pin using a pair of pliers and
re-fit to opposite side of hinge.(8)
11.Reposition plugs and hinge pin
bushings on top of doors on the
opposite side of both doors. Use small
flat-headed screwdrivers to remove
plugs and bushings. Take care not to
mark doors.(9)
IMPORTANT: We suggest you ask
somebody to help you when moving
the appliance around and to hold doors
when removing / re-fitting hinges and
doors to avoid any injury and damage
to the product.
Please refer to diagrams supplied. To
follow numbers in brackets below, refer
to the main diagram.
1.Switch off the appliance at the
socket outlet and pull out the mains
plug.
EN
10
12.Reposition left hand side feet on
22.Carefully stand the appliance
the opposite side.(10)
upright and adjust the two front feet if
13.Unscrew and remove the upper necessary.
door middle hinge pin bushing/
23.Check that doors open and close
door stopper using a cross-headed easily, they are aligned correctly and
screwdriver. Important: This part cannot that there are no gaps allowing air into
be used on the opposite side; left hand the cabinet. If there are gaps between
side middle hinge pin bushing/door the door seal and the cabinet, adjust
stopper part is supplied in the plastic the door seal by gently pulling away
bag.(11)
from the door using fingers.
14.Re-fit the upper hinge on the
24.Check that all the hinge screws
left hand side using flat-headed are tightened. Avoid over tightening the
screwdriver.(12)
screws.
15.Fit upper door left hand side
25.Put all items, fittings back in the
middle hinge pin bushing/door stopper appliance.
supplied in the plastic bag using cross-
headed screwdriver.(13)
26.Fit upper door top trim plastic
hinge cover. Upper door top trim hinge
16.Reposition three small plastic cover is supplied in the plastic bag.(21)
plugs on the left hand side, which are
covering middle hinge holes, on the
27.Wait for at least 4 hours to allow
the system to settle before switching
opposite side to cover holes left empty. on.
(14) 28.Once
the
correct
storage
17.Locate and re-fit upper door to temperatures have been reached in the
upper hinge and hold the door firmly. appliance, put back all the food.
(15)
18.Locate the middle hinge pin to
middle hinge pin bushing of upper door
on the left hand side and re-fit the
middle hinge.(16)
19.Reposition the two screws fitted
to lower hinge holes on the left hand
side at the bottom of the cabinet on the
opposite side.(17)
20.Unscrew and reposition the hinge
housing and steel pant on the right
hand side at the bottom of the door on
the opposite side. (18)
21.Locate and re-fit lower door to
middle hinge pin and then re-fit the
lower hinge on the left hand side.(19),
(20)
EN
11
20
7
1
1
6
2
14
5
11
13
9
45°
4
10
3
18
21
12
8
180°
15
16
19
17
20
EN
12
4 Before operating
Final Check
Before you start using the fridge/
freezer check that:
1. The feet have been adjusted for
perfect levelling.
2. The interior is dry and air can
circulate freely at the rear of the cabinet.
3. Clean the interior as recommended
under “CLEANING AND CARE.”
4. Insert the plug into the wall socket
and switch on the electricity supply.
• When the door is open the fridge
interior light will come on.
5. You will hear a noise as the
compressor starts up. The liquid and
gases sealed within the refrigeration
system may also give rise to noise,
whether the compressor is running or
not which is quite normal.
6. Set the setting half way between
min and max.
7. Front edges of the cabinet may
feel warm. This is normal. These areas
are designed to be warm to avoid
condensation.
8. “Do not load the appliance
immediately it is switched on. Wait until
the correct storage temperature has
been reached. We recommend that you
check the temperature with an accurate
thermometer (see; Temperature Control
and Adjustment)”
EN
13
5 Using your refrigerator
TEMPERATURE CONTROL AND
ADJUSTMENT
Rememberyoumusttakeyourreading
very quickly since the thermometer
temperature will rise very rapidly after
you remove it from the freezer.
Please remember each time the door
is opened cold air escapes and the
internal temperature rises. Therefore
never leave the door open and ensure
it is closed immediately after food is put
in or removed.
STORING FRESH FOOD
Operating temperatures are controlled
by the thermostat (Fig. 1) and may be
set at any position between 1 and 5,
5 being the coldest position. Towards
5 you will obtain a colder fridge
temperature and vice versa.
To switch off the appliance completely:
Turn the thermostat to “0” (Zero)
position.
Your freezer is suitable for the long-
term storage of commercially frozen
foods and also can be used to freeze
and store fresh food.
If there is a power failure do not open
the door. Frozen food should not be
affected if the failure lasts for less than
23 hrs. If the failure is longer, then the
food should be checked and either
eaten immediately or cooked and then
refrozen.
“Closed” setting will keep humidity
inside the salad crisper.
“Open” setting will increase air
circulation thereby reduce humidity in
the salad crisper.
If you wish to store food in the salad
crisper for longer , you should keep
the humidity adjustment in the closed
position.
FREEZING FRESH FOOD
Please
observe
the
following
instructions to obtain the best results.
Do not freeze too large a quantity at
any one time. The quality of the food
is best preserved when it is frozen
right through to the core as quickly as
The average temperature inside the
fridge depends on the following factors: possible.
• Ambient temperature in the room
(seasonal changes)
• Frequency of door opening
Do not exceed the freezing capacity
of your appliance in 24 h which is 3.5
kg (11lb)
• Placing hot food inside the product
• Position of the product inside the
room (being exposed to sun light)
We recommend that you check
the temperature with an accurate
thermometer to ensure that the storage
compartments are kept to the desired
temperature.
Placing warm food into the freezer
compartment causes the refrigeration
compressor to operate continuously
until the food is frozen solid. This can
temporarily lead to excessive cooling of
the refrigeration compartment.
EN
14
When freezing fresh food turn the
thermostat towards 5. Small quantities
of food up to 1/2 kg. (1 lb) can be
frozen without having to rotate the
temperature control knob.
You may place fresh food to be frozen
in any part of the freezer.
Take special care not to mix already
frozen food and fresh food.
B) FREEZER
COMPARTMENT
Defrosting is very easy and without
mess thanks to a special defrost
collection what is a basin.
Defrost twice a year or when a frost
layer of around 7 mm (1/4") has formed.
To start defrosting procedure switch
off the appliance at the socket outlet
and pull out the mains plug.
DEFROSTING
All food should be wrapped in several
layers of newspaper and stored in a
cool place (e.g. fridge or larder).
Containers full of warm water may be
placed carefully in the freezer to speed
up the defrosting.
Do not use pointed or sharp edged
objects such as knives, forks to remove
the frost.
A) FRIDGE COMPARTMENT
The fridge compartment defrosts
automatically. The defrosting water
runs to the drain tube via a collection
container at the back of the appliance
(1).(see diagram)
During defrosting water droplets
may form at the back of the fridge
Never use hairdryers, electrical heaters
and other similar electrical appliances
for defrosting.
compartment
where
concealed
evaporator is located.
Some droplets may remain on the
liner and refreeze when defrosting is
completed. Do not use pointed or sharp
edged objects such as knives, forks to
remove the droplets which have frozen.
If at any time the defrost water does
not drain from the collection channel,
check to ensure that no food particles
have blocked the drain tube. The drain
tube can be cleared by pushing the
special plastic plunger provided down
the drain tube (2). If the frost layer
reaches about 1/4"(7 mm), reduce
the setting (i.e. from 4 to 3) to restart
automatic defrosting.
When defrosting has finished, sponge
out any defrost water which collects at
the bottom of the freezer and dry the
interior thoroughly. Insert the plug in
to the wall socket and switch on the
electricity supply.
EN
15
6 Maintenance and cleaning
** We recommend that you switch off
the appliance at the socket outlet and
** Removal of door tray
• To remove door racks, remove all
pull out the mains plug before cleaning. the contents and then simply push the
door rack upwards from the base.
** Never use any sharp abrasive
instrument, soap, household cleaner,
detergent and wax polish for cleaning.
** To remove a freezer drawer, pull it as
far as possible, and then tilt it upwards,
and then pull it out completely.
** Use luke warm water to clean the
cabinet of the appliance and wipe it dry.
** To remove the freezer flap door, first
open the door 3” and then gently pull it
** Use a damp cloth wrung out in a off. Make sure that the flap is in place
solution of one teaspoon of bicarbonate before closing the freezer door.
of soda to one pint of water to clean the
interior and wipe it dry.
** Make sure that the special plastic
container (drain tray) at the back of
** Make sure that no water enters the the appliance which collects defrost
lamp housing.
water is clean at all times. If you want
to remove the tray to clean it follow the
** If the appliance is not going to be instructions below :
used for a long period of time switch it
• Switch off at the socket outlet and
off, remove all food, clean it and leave pull out the mains plug.
the door ajar.
• Push the lug down with the tip of
a screw driver & pull out with a jerk
** Any dust that gathers on the movement
condenser, which is located at the back
of the appliance, should be removed
once a year with a vacuum cleaner.
• Clean the drain tray and wipe it dry.
• Reassemble reversing the sequence
and operations.
** Check door seals regularly to
** Avoid spillage of food particularly
ensure they are clean and free from small items like rice, peas, beans
food particles.
through the fan guard as they may
cause the cooling system to block and
therefore operate less efficiently.
EN
16
7 Do's and Don'ts
Do- Wrap all food in aluminium foil or
freezer quality polythene bags and
make sure any air is excluded.
Do- Wrap frozen food when you buy it
and put it in to the freezer as soon
as possible.
Do- Defrost food in the fridge
compartment.
Do- Remove ice cream from the
freezer 10-20 minutes before
serving.
Don’t- Store bananas in your fridge
compartment.
Don’t- Store melon in your fridge. It
can be chilled for short periods as
long as it is wrapped to avoid it
flavouring other food.
Do- Clean your appliance regularly
(See “Cleaning and Care”)
Do- Keep raw meat and poultry below
cooked food and dairy products.
Do- Take off any unusable leaves on
vegetables and wipe off any soil.
Do- Leave lettuce, cabbage, parsley
and cauliflower on the stem.
Do- Wrap cheese firstly in greaseproof
paper and then in a polythene bag
excluding as much air as possible.
For best results take out of the
fridge compartment an hour before
eating.
Do- Wrap raw meat and poultry
loosely in polythene or aluminium
foil. This prevents drying.
Don’t- Store poisonous or any
dangerous substances in your
appliance. It has been designed
for the storage of edible foodstuffs
only.
Don’t- Consume food which has been
stored for an excessive time in the
fridge.
Don’t- Store cooked and fresh food
together in the same container.
They should be packaged and
stored seperately.
Don’t- Let defrosting food or food
juices drip onto food.
Don’t- Leave the door open for long
periods as this will make the
appliance more costly to run and
cause excessive ice formation.
Don’t- Put hot food into the appliance.
Let it cool down first.
Do- Wrap fish and offal in polythene
bags.
Do- Wrap food which have a strong
odour or can dry out in polythene
bags, aluminium foil or place in an
airtight container.
Do- Wrap bread well to keep it fresh.
Do- Chill white wines, beer, lager and
mineral water before serving.
Do- Check contents of the freezer
every so often.
Do- Keep food for as short a time
as possible and adhere to “Best
Before”, “Use by” etc. dates.
Do- Store commercially frozen food in
accordance with the instructions
given on the packets that you buy.
Do- Always choose high quality fresh
food and be sure it is thoroughly
clean before you freeze it.
Don’t- Put liquid-filled bottles or sealed
cans containing carbonated liquids
into the freezer as they may burst.
Do- Prepare fresh food for freezing
in small portions to ensure rapid
freezing.
EN
17
Don’t- Exceed the maximum freezing
loads (3,5 kg in any 24 hours)
when freezing fresh food.
Don’t- Give children ice-cream and
water ices direct from the freezer.
The low temperature may cause
‘freezer burns’ on lips.
PROBLEM SOLVING
If the appliance does not operate
when switched on, check whether:
• The plug is inserted properly in the
socket and that the power supply is
on. (To check the power supply to the
socket, plug in another appliance)
• The fuse has blown/circuit breaker
has tripped/main distribution switch
has been turned off.
Don’t- Freeze fizzy drinks.
Don’t- Try to keep frozen food which
has thawed, it should be eaten
within 24 hours or cooked and
refrozen.
Don’t- Remove items from the freezer
with wet hands.
Don’t- Close the freezer door before
placing the compartment cover in
its place.
Don’t- Leave frozen food at room
temperature to thaw; the best way
to defrost food is to put it in the
fridge to thaw slowly. Make sure
you avoid defrosting food or food
juices drip onto other food.
• The temperature control has been
set correctly and not to “0” (OFF)
• New plug is wired correctly if you
have changed the fitted moulded plug.
If the appliance is still not operating
after the above checks, please refer to
the section on “How To Obtain Service”.
Please ensure that above checks have
been made as a charge will be made if
no fault is found.
EN
18
GUARANTEE DETAILS
Your new Beko product is guaranteed against the cost of breakdown repair for
twelve months from the date of the original purchase.
What is covered?
• Repairs necessary as a result of faulty materials, defective components or
manufacturing defect.
• The cost of functional replacement parts, but excluding consumable items.
• The labour costs of a Beko approved repairer to carry out the repair.
What is not covered?
• Transit, delivery or accidental damage or misuse and abuse.
• Cabinet or appearance parts, including control knobs, flaps, handles or
container lids.
• Accessories or consumable items including but not limited to, ice trays,
scrapers, cutlery baskets, filters and light bulbs.
• Repairs required as a result of unauthorised repair or inexpert installation that
fails to meet the requirements contained in the user instruction book.
• Repairs to products used on commercial or non-residential household
premises.
• Loss of frozen food in freezers or fridge/freezers. (Food loss insurance is
often included within your household contents insurance policy, or may be
available separately from your retailer).
Important notes.
• Your Beko product is designed and built for domestic household use only.
• The guarantee will be void if the product is installed or used in commercial
or non-residential domestic household premises.
• The product must be correctly installed, located and operated in accordance
with the instructions contained in the User Instructions Booklet provided.
• Professional installation by a qualified Electrical Domestic Appliance Installer
is recommended for all Washing Machines, Dishwashers and Electric Cookers
• Gas Cookers must only be installed by a Gas Safe (or BORD GAIS) registered
Gas Installer.
• The guarantee is given only within the boundaries of the United Kingdom
and the Republic of Ireland.
• The guarantee is applicable only to new products and is not transferable if
the product is resold.
• Beko disclaims any liability for incidental or consequential damages.
The guarantee does not in anyway diminish your statutory or legal rights.
EN
19
HOW TO OBTAIN SERVICE
Please keep your purchase receipt or other proof of purchase in a safe
place; you will need to have it should the product require attention under
guarantee.
You should also complete the details below; it will help us assist you when
requesting service. (The model number is printed on the Instruction Booklet and
the serial number is printed on the Rating Label affixed to the appliance)
Model No:
Serial No:
Retailer:
Date of purchase:
For service under guarantee simply telephone the appropriate number
below
UK Mainland & Northern Ireland
Fridges & Freezers
Electric Cookers
Gas & Dual Fuel Cookers
Washing Machines
& Dishwashers
0845 6004903
0845 6004902
0845 6004905
0845 6004906
Republic of Ireland
All Refrigeration, All Cookers
Washing Machines & Dishwashers
01 862 3411
Before requesting service please check the trouble-shooting guide in
the Operating Instructions as a charge may be levied where no fault is
found even though your product may still be under guarantee.
Service once the manufacturers guarantee has expired.
If you have purchased an extended guarantee please refer to the instructions
contained within the extended guarantee agreement document. Otherwise
please call the appropriate number above where service can be obtained at a
charge.
Should you experience any difficulty in obtaining service please contact the Beko
Customer Help-Line.
EN
20
BEKO plc
Beko House
Caxton Way
Watford
Hertfordshire
WD18 8UF
Tel: 0845 6004911
Fax: 0845 6004922
e-mail: [email protected]
Printed in Turkey
Part no:
Revision no: AB
57 1218 0000
|