Belkin Pet Fence 8820bt01379 User Manual

TuneBase™ AUX with Hands-Free  
User Manual  
8820bt01379 Rev. A00 F8J037bt  
 
INTRODUCTION  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
Features  
iPhone only  
iPod and iPhone  
Receive calls from your iPhone and talk  
hands-free  
Play your iPod through your car’s stereo  
Keep your iPod in its case  
Listen to calls through your car stereo  
Built-in mic for hands-free phone calls  
Easily activate and use Siri Assistant  
Rotate your iPod to horizontal view  
Secure and flexible cradling for any size iPod  
 
TuneBaseDirect with Hands-Free  
1
INTRODUCTION  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
What’s in the Box  
2.  
3.  
1.  
1. TuneBase AUX with Hands-Free  
2. Fit Ring (optional)  
3. 3.5mm Audio Cable  
 
TuneBaseDirect with Hands-Free  
2
SET UP YOUR TUNEBASE  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
Plug In Your TuneBase  
Follow the steps in this section to set up your TuneBase AUX with Hands-Free (the TuneBase).  
These steps coincide with those in the Quick Install Guide but provide more detail.  
2. Test the tightness of fit in the power  
outlet. The TuneBase should give some  
resistance when you try to rotate it inside  
the power outlet. It should not rotate or  
move on its own.  
1. Insert your TuneBase into the power  
outlet in your car.  
If the TuneBase is too loose or too tight in  
the power outlet, see the troubleshooting  
section for instructions on adjusting  
the fit.  
Warning: Do not rotate the TuneBase in the  
power outlet. If you experience resistance,  
unplug the TuneBase and reinsert it in  
the desired position. Failure to do so may  
damage the cigarette lighter adapter or  
power outlet.  
 
TuneBaseDirect with Hands-Free  
3
SET UP YOUR TUNEBASE  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
Dock Your iPod  
1. Push the button on the springboard and  
2. Connect your iPod to the TuneBase dock  
slide it to its maximum height.  
connector, making sure it is fully seated.  
 
TuneBaseDirect with Hands-Free  
4
SET UP YOUR TUNEBASE  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
3. Push the front of the iPod back until the  
back of the iPod touches the front of  
the springboard.  
4. Push down on the top of the springboard  
until it holds your iPod securely in place.  
Note: After you have adjusted the height of  
the springboard, there is no need to adjust  
the TuneBase to insert and remove your iPod.  
 
TuneBaseDirect with Hands-Free  
5
SET UP YOUR TUNEBASE  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
5. Connect the audio cable to the  
headphone jack on your iPod.  
 
TuneBaseDirect with Hands-Free  
6
SET UP YOUR TUNEBASE  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
6. Bend the flexible neck to position your iPod.  
Warning: Do not remove the TuneBase from  
the cigarette lighter adapter when an iPod is  
in the cradle.  
Do not position your TuneBase as follows:  
 
TuneBaseDirect with Hands-Free  
7
SET UP YOUR TUNEBASE  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
Remove your Device from your TuneBase  
1. Disconnect the audio cable from your iPod.  
2. Push back on the front of the springboard and tilt your iPod forward until it clears the  
lip of the springboard.  
3. Lift your iPod out of the cradle.  
1
2
3
 
TuneBaseDirect with Hands-Free  
8
SET UP YOUR TUNEBASE  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
Dock Your Device After Initial Setup  
After you have adjusted the TuneBase to fit your iPod, you can insert and remove your iPod  
without further adjustment.  
1. Seat your iPod on the dock connector.  
2. Push the face of the iPod so that it snaps  
into place under the lip of the springboard.  
 
TuneBaseDirect with Hands-Free  
9
SET UP YOUR TUNEBASE  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
3. Connect the audio cable from your  
Power behavior  
TuneBase to your iPod.  
Your iPod will automatically pause when you  
remove it from the TuneBase.  
Your TuneBase will automatically turn on  
when your iPod is connected and power is  
available. It turns off when you remove the  
iPod or power becomes unavailable.  
In some cases, the iPod will remain on and  
playing if docked in the TuneBase, even if  
there is no power. Be sure to undock your  
iPod completely to avoid draining the battery  
when not in use.  
You only need to adjust the height of the  
springboard when you are using a different  
iPod or different case.  
 
TuneBaseDirect with Hands-Free  
10  
USE YOUR TUNEBASE  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
Connect Your TuneBase to Your Car Stereo  
The 3.5mm audio-out jack on the TuneBase lets you connect to the aux-in jack on your car  
stereo. You can also use the jack to connect to your car’s cassette tape player using a tape  
adapter (sold separately).  
1. Make sure your car stereo and TuneBase  
3. Connect the audio cable to the audio-out  
are powered off.  
jack on the TuneBase.  
2. Connect the 3.5mm audio cable to the  
aux-in jack on your car stereo.  
4. Power on your car stereo and TuneBase.  
5. On your car stereo, change the source  
to “aux”.  
6. You are now ready to listen to your iPod.  
 
TuneBaseDirect with Hands-Free  
11  
USE YOUR TUNEBASE  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
Adjust your car stereo’s volume to get the  
right level of sound. If the volume remains  
too faint, increase the volume on your iPod to  
boost the signal.  
Play Music  
Use the controls on your iPod to navigate to  
your playlists. Then, use the Multifunction  
button to play and pause music.  
Note: Make sure you select the correct  
source on your car stereo.  
1. On your iPod, select the track you want  
to play.  
Select “aux” when the cable is connected  
to the aux-in on your stereo.  
2. Adjust the volume on your iPod to  
get adequate signal strength without  
distortion.  
Select “tape” if you are using a  
cassette adapter.  
3. Press the Multifunction button to play  
Warning: To prevent damage to your  
TuneBase, turn off your car stereo and  
TuneBase before connecting an audio cable.  
and pause music.  
Activate Siri Assistant  
To activate the Siri Assistant, press and hold  
the multifunction button.  
 
TuneBaseDirect with Hands-Free  
12  
USE YOUR TUNEBASE  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
To play or pause music, press the  
Multifunction button once.  
Receive Calls  
When there is an incoming call, the music will  
automatically pause to allow you to hear the  
ringtone of your iPhone.  
To skip to the next track, press the  
Multifunction button twice.  
To skip to the previous track, press the  
Multifunction button three times.  
Receive calls through your TuneBase  
Note: Your iPod will automatically pause when  
you remove it from the TuneBase. In some  
cases, the iPhone/iPod will remain on and  
playing if docked in the TuneBase even if there  
is no power or the car keys are removed. Be  
sure to undock your iPhone/iPod completely  
to avoid draining the battery when not in use.  
The TuneBase has a built-in microphone  
that lets you talk without a headset. The  
caller’s voice will play through your car  
stereo speakers.  
1. Press the Multifunction button to receive  
an incoming call.  
2. Press the Multifunction  
button again to hang up.  
Your music will resume  
when the call ends.  
 
TuneBaseDirect with Hands-Free  
13  
USE YOUR TUNEBASE  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
Hearing the other party  
Receive calls through your  
Bluetooth® headset  
If you cannot hear the other party through  
your car speakers, do the following:  
If you have a Bluetooth headset paired with  
your iPhone, you can receive calls on your  
headset. Press the button on your headset  
to receive an incoming call. Your music will  
resume when you hang up.  
1. Set the phone volume on your iPhone to  
maximum.  
2. If necessary, slowly turn up the volume  
on your car stereo until you can hear the  
caller’s voice.  
Reduce echo  
If you hear an echo when talking hands-free,  
do the following:  
1. Position your iPhone so that its screen  
is facing toward you and away from your  
car’s speakers.  
2. Set the phone volume on your iPhone to  
maximum and turn down the volume on  
your car stereo until you no longer hear  
the echo.  
 
TuneBaseDirect with Hands-Free  
14  
TROUBLESHOOTING  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
You can quickly solve most problems with your TuneBase by following the advice in this section.  
You cannot hear the other party.  
Your iPod or iPhone is not charging.  
Solution  
Solution  
Set the phone volume on your iPhone  
to maximum.  
Make sure your TuneBase has a good  
connection to your car’s power outlet.  
If necessary, slowly turn up the volume  
on your car stereo until you can hear the  
caller’s voice.  
Make sure your iPod or iPhone is fully  
seated in the cradle.  
Make sure the power outlet is receiving  
power. Some vehicles do not provide  
power to the power outlet unless the  
vehicle is in ignition mode or the engine  
is running.  
The other party experiences an echo  
when you’re talking hands-free.  
Solution  
Position your iPhone so that its screen  
is facing toward you and away from your  
car’s speakers.  
Your TuneBase and iPhone/iPod are in  
the way of your vehicle’s controls.  
Make sure the phone volume on your  
iPhone is set to maximum.  
Solution  
Use the flexible gooseneck and the  
articulation behind the docking cradle to  
position your TuneBase away from your  
vehicle’s controls. Position the gooseneck in  
as upright a position as possible in relation to  
the power adapter.  
Turn down your stereo volume until they  
no longer hear an echo.  
 
TuneBaseDirect with Hands-Free  
15  
TROUBLESHOOTING  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
Your TuneBase rotates out of position  
around the center of the power outlet.  
Solution 3  
The fit ring may be too large for some cars’  
power adapters. Use scissors to carefully  
cut as many prongs as you need. Try to fit  
your TuneBase into the power outlet after  
each cut. When cutting multiple prongs, cut  
prongs on opposing sides.  
Solution 1  
Be sure to solidly attach the cigarette lighter  
adapter of the TuneBase to the power outlet.  
Test the stability by pushing it sideways  
before driving.  
CUT  
Solution 2  
CUT  
CUT  
In some vehicles, the power outlet is wider  
than the cigarette lighter adapter of the  
TuneBase. You may notice a wiggle in your  
TuneBase when you push it. In that case,  
slide the fit ring around the cigarette lighter  
adapter of the TuneBase. Then, insert the  
cigarette lighter adapter into the power  
outlet, making sure that all four prongs of the  
fit ring securely fit in the power outlet. If the  
fit is too tight, you can cut off one or more of  
the prongs on the fit ring and try the fit again  
(see Solution 3).  
 
TuneBaseDirect with Hands-Free  
16  
TROUBLESHOOTING  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
Your TuneBase connects firmly to the  
power outlet, but it still rotates.  
The rubber friction washer remained in  
the power outlet when you removed  
your TuneBase.  
Solution  
Solution  
Check to see if the power outlet rotates in its  
socket. If so, please consult your vehicle’s  
manufacturer.  
This is rare, but if it occurs you can remove  
the rubber washer from the power outlet and  
place it back on the cigarette lighter adapter.  
Warning: Disconnect the vehicle’s battery.  
Any attempt to remove the washer  
without disconnecting the battery may  
result in physical harm to you or damage  
to the vehicle.  
You cannot insert the cigarette lighter  
adapter into the power outlet.  
Solution  
The cigarette lighter adapter’s rubber friction  
washer may need to be centered. Follow the  
steps below to center the friction washer.  
Use pliers to carefully remove the friction  
washer from the power outlet. Place the  
friction washer back on the cigarette lighter  
adapter. Then, reconnect the vehicle’s  
battery.  
1. Use pliers to loosen the nut on the front of  
the cigarette lighter adapter slightly. It is  
not necessary to remove the nut.  
2. Move the friction washer back into  
centered position.  
3. Tighten the nut firmly.  
 
TuneBaseDirect with Hands-Free  
17  
SAFETY WARNINGS  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
Your TuneBase requires full concentration  
and both hands to install. Do not attempt  
to connect your TuneBase while driving.  
Make sure your TuneBase fits securely and  
firmly into the power outlet before driving.  
After installation, make sure your TuneBase  
does not freely rotate in the power outlet.  
Do not insert any objects other than the  
cigarette lighter adapter into the power  
outlet without disconnecting the battery  
of the vehicle first. Failure to observe  
this safety warning can result in injury or  
property damage.  
Belkin does not assume any responsibility for  
personal injury or property damage incurred  
due to hazardous driving as a result of  
interaction with the TuneBase, the iPod and  
iPhone, or the vehicle’s power outlet.  
Do not attempt to adjust or retrieve  
an unsecured TuneBase or iPod while  
driving. Adjust the position of your TuneBase  
so that it and your iPod do not interfere with  
any of the operating controls of the vehicle.  
 
TuneBaseDirect with Hands-Free  
18  
INFORMATION  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
FCC Statement  
radiate radio frequency energy and, if not  
installed and used in accordance with the  
DECLARATION OF CONFORMITY WITH  
FCC RULES FOR ELECTROMAGNETIC  
COMPATIBILITY  
instructions, may cause harmful interference  
to radio communications. However, there  
is no guarantee that interference will not  
occur in a particular installation. If this  
equipment does cause harmful interference  
to radio or television reception, which can be  
determined by turning the equipment off and  
on, the user is encouraged to try to correct  
the interference by one of the following  
measures:  
We, Belkin International, Inc., of 12045 E.  
Waterfront Drive, Playa Vista, CA 90094,  
declare under our sole responsibility that  
the product, SKU No: F8J037, to which this  
declaration relates, complies with Part 15  
of the FCC Rules. Operation is subject to  
the following two conditions: (1) this device  
may not cause harmful interference, and (2)  
this device must accept any interference  
received, including interference that may  
cause undesired operation.  
• Reorient or relocate the receiving antenna.  
Increase the distance between the  
equipment and the receiver.  
Connect the equipment to an outlet on  
a circuit different from that to which the  
receiver is connected.  
Federal Communications  
Commission Notice  
Consult the dealer or an experienced  
radio/TV technician for help.  
This equipment has been tested and found  
to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC  
Rules. These limits are designed to provide  
reasonable protection against harmful  
interference in a residential installation.  
FCC Caution: Any changes or modifications  
not expressly approved by the party  
responsible for compliance could void the  
user’s authority to operate this equipment.  
This equipment generates, uses, and can  
 
TuneBaseDirect with Hands-Free  
19  
INFORMATION  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
IMPORTANT NOTE:  
IC Statement:  
This digital apparatus complies with CAN  
ICES-3(B)/NMB-3 (B)  
Industry Canada Statement  
This device complies with ICES-003 of the  
Industry Canada Rules. Operation is subject  
to the following two conditions:  
1) This device may not cause  
interference, and  
2) This device must accept any interference,  
including interference that may cause  
undesired operation of the device.  
Ce dispositif est conforme a la norme  
CNR- standards d’Industrie Canada  
applicable aux appareils radio pas produire  
de brouillage prejudiciable, et (2) ce dispositif  
doit accepter tout brouillage recu, y compris  
un brouillage susceptible de provoquer un  
fonctionnement indesirable.  
 
TuneBaseDirect with Hands-Free  
20  
INFORMATION  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
CE Declaration of Conformity  
encouraged to try to correct the interference  
by one of the following measures:  
• Reorient or relocate the receiving antenna.  
We, Belkin International, Inc., declare under  
our sole responsibility that the product  
F8J037, to which this declaration relates, are  
in conformity with EMC Directive 2004/108/  
EC, Low Voltage Directive 2006/95/EC  
Energy Directive 2005/32/EC & 2009/125/EC  
RoHS Directive 2011/65/EU (Recast).  
• Increase the separation between the  
equipment and receiver.  
• Connect the equipment into an outlet on  
a circuit different from that to which the  
receiver is connected.  
• Consult the dealer or an experienced radio/  
TV technician for help.  
We further declare that the product meets the  
essential requirement of the above Directives.  
The limits contain in these articles are  
designed to provide reasonable protection  
against harmful interference in a residential  
installation. This equipment generates uses  
and can radiate radio frequency energy  
and, if not installed and used in accordance  
with the instructions, may cause harmful  
interference to radio communications.  
However, there is no guarantee that  
Caution: Any changes or modifications not  
expressly approved by the party responsible  
for compliance could void the user’s authority  
to operate this equipment.  
interference will not occur in a particular  
installation. If this equipment does cause  
harmful interference to radio or television  
reception, which can be determined by  
turning the equipment off and on, the user is  
 
TuneBaseDirect with Hands-Free  
21  
INFORMATION  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
Belkin International, Inc., Limited 2-Year Limited Product Warranty  
What this warranty covers.  
evidenced on the original purchase receipt as  
discounted by its natural use.  
Belkin International, Inc. (“Belkin”) warrants to  
the original purchaser of this Belkin product  
that the product shall be free of defects in  
design, assembly, material, or workmanship.  
What is not covered by this warranty?  
All above warranties are null and void if the  
Belkin product is not provided to Belkin  
for inspection upon Belkin’s request at the  
sole expense of the purchaser, or if Belkin  
determines that the Belkin product has been  
improperly installed, altered in any way, or  
tampered with. The Belkin Product Warranty  
does not protect against acts of God such as  
flood, lightning, earthquake, war, vandalism,  
theft, normal-use wear and tear, erosion,  
depletion, obsolescence, abuse, damage due  
to low voltage disturbances (i.e. brownouts  
or sags), non-authorized program, or system  
equipment modification or alteration.  
What the period of coverage is.  
Belkin warrants the Belkin product for  
two years.  
What will we do to correct problems?  
Product Warranty.  
Belkin will repair or replace, at its option, any  
defective product free of charge (except for  
shipping charges for the product). Belkin  
reserves the right to discontinue any of its  
products without notice, and disclaims any  
limited warranty to repair or replace any  
such discontinued products. In the event  
that Belkin is unable to repair or replace the  
product (for example, because it has been  
discontinued), Belkin will offer either a refund  
or a credit toward the purchase of another  
product from Belkin.com in an amount equal  
to the purchase price of the product as  
 
TuneBaseDirect with Hands-Free  
22  
INFORMATION  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
How to get service.  
2. Your Belkin Customer Service  
To get service for your Belkin product you  
must take the following steps:  
Representative will then instruct you on  
how to forward your receipt and Belkin  
product and how to proceed with  
your claim.  
1. Contact Belkin International, Inc., at  
12045 E. Waterfront Drive, Playa Vista,  
CA 90094, Attn: Customer Service, or  
call (800)-223-5546, within 15 days of the  
Occurrence. Be prepared to provide the  
following information:  
Belkin reserves the right to review the  
damaged Belkin product. All costs of  
shipping the Belkin product to Belkin for  
inspection shall be borne solely by the  
purchaser. If Belkin determines, in its sole  
discretion, that it is impractical to ship the  
damaged equipment to Belkin, Belkin may  
designate, in its sole discretion, an equipment  
repair facility to inspect and estimate the  
cost to repair such equipment. The cost, if  
any, of shipping the equipment to and from  
such repair facility and of such estimate  
shall be borne solely by the purchaser.  
Damaged equipment must remain available  
for inspection until the claim is finalized.  
Whenever claims are settled, Belkin reserves  
the right to be subrogated under any existing  
insurance policies the purchaser may have.  
a. The part number of the Belkin product.  
b. Where you purchased the product.  
c. When you purchased the product.  
d. Copy of original receipt.  
 
TuneBaseDirect with Hands-Free  
23  
INFORMATION  
Table of Contents  
SECTIONS  
1
2
3
4
5
6
How state law relates to the warranty.  
THIS WARRANTY CONTAINS THE SOLE  
WARRANTY OF BELKIN. THERE ARE  
NO OTHER WARRANTIES, EXPRESSED  
OR, EXCEPT AS REQUIRED BY LAW,  
IMPLIED, INCLUDING THE IMPLIED  
WARRANTY OR CONDITION OF QUALITY,  
MERCHANTABILITY OR FITNESS FOR  
A PARTICULAR PURPOSE, AND SUCH  
IMPLIED WARRANTIES, IF ANY, ARE  
LIMITED IN DURATION TO THE TERM OF  
THIS WARRANTY.  
IN NO EVENT SHALL BELKIN BE LIABLE  
FOR INCIDENTAL, SPECIAL, DIRECT,  
INDIRECT, CONSEQUENTIAL OR MULTIPLE  
DAMAGES SUCH AS, BUT NOT LIMITED  
TO, LOST BUSINESS OR PROFITS ARISING  
OUT OF THE SALE OR USE OF ANY BELKIN  
PRODUCT, EVEN IF ADVISED OF THE  
POSSIBILITY OF SUCH DAMAGES.  
This warranty gives you specific legal rights,  
and you may also have other rights, which  
may vary from state to state. Some states  
do not allow the exclusion or limitation of  
incidental, consequential, or other damages,  
so the above limitations may not apply to you.  
Some states do not allow limitations on how  
long an implied warranty lasts, so the above  
limitations may not apply to you.  
Licensed Under U.S. Patent No. 6,591,085  
 
TuneBaseDirect with Hands-Free  
24  
Belkin Tech Support  
US  
UK  
Australia  
New Zealand  
Singapore  
1800 622 1130  
Europe  
© 2013 Belkin International, Inc. All rights reserved. All trade names are registered trademarks of  
respective manufacturers listed. iPhone and iPod are trademarks of Apple Inc., registered in the U.S. and  
other countries. The Bluetooth name and the Bluetooth trademarks are owned by Bluetooth SIG, Inc.,  
and are used by Belkin International, Inc., under license.  
“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed  
to connect specifically to iPod or iPhone, respectively, and has been certified by the developer  
to meet Apple performance standards. Apple is not responsible for the operation of this  
device or its compliance with safety and regulatory standards. Please note that the use of this  
accessory with iPod or iPhone may affect wireless performance.  
 

Black Decker Fryer EF40 User Manual
Blue Rhino Insect Control Equipment CPSV002704 User Manual
Boca Research Network Card 11Mbps User Manual
Bookendz Laptop Docking Station BE 10350 User Manual
Broan Ventilation Hood L100 Series User Manual
Brother Toaster PT H500LI User Manual
Bryan Boilers Water Heater BE 210 WT4T7 User Manual
Cabletron Systems Switch 6E122 26 User Manual
C Crane Digital Camera 024 S User Manual
Chamberlain Intercom System NLS1 User Manual