Spot Lifter®
POWERBRUSH
H A N D H E L D D E E P C L E A N E R
U S E R ’ S G U I D E
1716 SERIES
3
4
5
Safety Instructions
Product View
Product Features
6-7
8-9
Operations
Maintenance and care
9-10
Troubleshooting
Consumer Services
Replacement Parts
Warranty
10
11
12
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic
precautions should be observed, including
the following:
■ Always connect to a properly grounded outlet; see
grounding instructions.
■ Do not modify the 3-prong grounded plug.
Read all instructions before using your
Spot Lifter® Powerbrush
SAVE THESE
WARNING - To
reduce the risk of fire,
electric shock, or injury:
INSTRUCTIONS
GROUNDING
■ Do not use for any purpose other than described in
this User’s Guide.
INSTRUCTIONS
■ Use only BISSELL cleaning products intended for
This appliance must be connected to a grounded wir-
ing system. If it should malfunction or break down,
grounding provides a safe path of least resistance
for electrical current, reducing the risk of electrical
shock. The cord for this appliance has an equip-
ment-grounding conductor and a grounding plug. It
must only be plugged into an outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
use in this appliance.
■ Use only manufacturer’s recommended
attachments.
■ Do not expose to rain, store indoors.
■ Do not handle plug or appliance with wet hands.
■ Do not leave Spot Lifter® PowerBrush when it is
plugged in.
■ Do not put any object into appliance openings or use
with blocked openings. Keep free of dust, lint, hair, and
anything that may reduce air flow.
Grounded
Outlets
■ Do not expose hair, loose clothing, fingers or body
parts to openings or moving parts.
■ Be extra careful when cleaning stairs.
Grounding Pin
■ Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
■ Do not pick up hot or burning objects.
WARNING:
Improper
■ Do not pick up flammable or combustible materials (lighter
fluid, gasoline, kerosene, etc.) or use in the presence of
explosive liquids or vapor.
connection of the equipment-grounding
conductor can result in a risk of electrical
shock. Check with a qualified electrician
or service person if you aren’t sure if the
outlet is properly grounded. DO NOT MODIFY
THE PLUG. If it will not fit the outlet, have
a proper outlet installed by a qualified
electrician. This appliance is designed for
use on a nominal 120-volt circuit, and has
a grounding attachment plug that looks like
the plug in the drawing above. Make certain
that the appliance is connected to an outlet
having the same configuration as the plug.
No plug adapter should be used with this
appliance.
■ Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, gasoline, etc.).
■ Do not use appliance in an enclosed space filled with
vapors given off by oil base paint, paint thinner, some
moth proofing substances, flammable dust,or other
explosive or toxic vapors.
■ Do not pull or carry by cord, use cord as a handle,
close door on cord, pull cord around sharp corners
or edges, run appliance over cord, or expose cord
to heated surfaces.
■ Do not use with damaged cord or plug.
■ Do not immerse. Use only on surface moistened by
cleaning process.
■ Do not use Spot Lifter® PowerBrush if it has been
dropped, damaged, left outdoors or dropped into water.
Have it repaired at an Authorized Service Center.
This model is for household use only.
■ Turn off all controls before unplugging.
■ Unplug from outlet when not in use and before
conducting maintenance and troubleshooting.
■ Unplug by grasping the plug, not the cord. Do not
unplug by pulling on cord.
3
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Product view
Solution Tank
Solution Tank
Release Tabs
Power Switch
Spray Trigger
Power Cord
Removable Brush
Cartridge with Dual
PowerBrushes
Collection Tank
Belt Cover Door
Circuit Interrupting
Device (C.I.D.)
Spray Nozzle
CAUTION:
Only use one of BISSELL's
advanced formulas for portable deep cleaning
machines in your cleaner. Use of cleaning formulas
which contain lemon or pine oil may damage this
appliance and void warranty. Do not use chemical
spot cleaners or solvent-based soil removers. These
products may react with the plastic materials used in
your cleaner, causing cracking or pitting.
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
4
Product features
Solution tank. Holds 2X Little Green® formula
and water.
Collection tank. Collects dirty water and solution.
You will need to remove the solution tank
before you can remove the collection tank.
Spray trigger. Dispenses water
and solution.
Solution tank release tabs. Gently press in to
remove the clean/solution Tank.
Circuit Interrupting Device (C.I.D.).
Because you will be using this product in
wet environments, such as bathrooms, we
have equipped this unit with this added
safety feature. The C.I.D. shuts off the
product in potentially hazardous situations.
The C.I.D. has test (white) and reset (red)
buttons which should be operated each time
the product is plugged in.
Removable brush cartridge with dual
PowerBrushes. Double the cleaning action
to lift and remove stains and dirt. Removable
for easy cleaning.
WARNING:
Do not use an extension cord with this
product. The use of an extension cord may
result in a severe electrical shock, particularly
if the extension cord does not have an
electrical rating higher than that of the
product, OR if the extension cord does not
have a three-prong grounding plug and if
the extension cord is not plugged into a
circuit box with a ground fault circuit inter-
rupter. Safety precautions such as keeping all
connections off the ground and dry will not
eliminate the danger.
5
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Operations
Filling the solution tank
1. Remove the solution tank by gently pressing
the quick release tabs on the solution tank
and sliding the tank off of the unit.
1.
2. Open the tank by unscrewing and remov-
ing the cap. Add water and formula* to the
indicated fill lines on the solution tank.
*NOTE: Your Spot Lifter PowerBrush
includes an 8 oz. trial size formula.
2.
3. Replace the cap before placing the tank
back on the unit.
Pre-treating
To aid in the removal of tough, stubborn stains,
pre-treating the stain may be necessary.
1. Hold the unit above the area to be cleaned.
Using the manual trigger spray, apply a sufficient
amount of water and solution to the stain.
2. Wait 3-5 minutes before cleaning.
Cleaning
1. Plug in the unit.
2. While holding the Spot Lifter PowerBrush above
the area to be cleaned, apply water and formula
by pressing the manual trigger spray,
2.
dispensing fluid to the soiled/stained area.
3. Turn the power switch to the “ON” position. ( I )
4. Brushing and suction can be done separately,
based on how you hold and use the unit.
3.
To Use The Dual PowerBrushes Only:
Tilt the unit forward slightly, placing both brushes
in contact with the carpet.The flat surface of the
brush cartridge should be parallel to the surface
being cleaned.
For Suction Only:
Tilt the unit forward, pressing the front of the
Spot Lifter Powerbrush firmly against the sur-
face area to be cleaned, lifting the brushes up
off the surface. Pull toward you to remove the
soil and cleaning solution.
Note: Step #4 may be repeated until no
more dirty water is removed or until the
area to be cleaned meets your satisfaction.
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
6
Operations
Cleaning (continued)
5. Check the collection tank and empty the tank
if it is full (See To empty the collection tank,
page 8).
Tip:
You may also spray water
and formula, with the
manual trigger spray, while
the unit is turned on and
you are using the dual
PowerBrushes then suction
to clean.
6. If the Spot Lifter PowerBrush stops
spraying, turn off the unit and check the
cleaning solution level in the solution tank.
Refill if needed. Never run the unit without
water or cleaning solution.
Spot cleaning upholstery
1. Check manufacturer’s tag before cleaning.
“W” or “WS” on the tag means you can use
your Spot Lifter PowerBrush. If tag is coded
with an “S” (with diagonal strike-through) or
states “Dry Clean Only”, do not proceed.
Tip:
When cleaning a vertical
surface (ie: chair back, auto
interior, etc.) begin with a
completely empty collection
tank.
2. If manufacturer’s tag is missing or not
coded, check with your furniture dealer.
3. If possible, check upholstery stuffing.
Colored stuffing may bleed through fabric
when wet.
7
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Maintenance and care
Machine care
1. Turn the power switch to the “OFF”
position. ( O )
2. Unplug the unit.
1.
3. Carry the Spot Lifter PowerBrush to the sink
or drain.
To empty the collection tank
1. Begin by removing the solution tank. Gently
press the quick release tabs on the solution
tank and slide the tank off of the unit.
2.
3.
2. Grasp the collection tank and pull to
remove.
3. While at the sink, remove the tank cap by
unscrewing and lifting out.
4. Empty the tank. Rinse the collection tank
with warm water.
5. Replace cap by turning to the right, until snug.
6. Slide the collection tank into the unit.
Replace the solution tank.
Note: If a significant amount of water and
formula remains in the solution tank, you
may leave it in the solution tank for your
next cleaning task.
To clean the dual powerbrush
1.
2.
NOTE: Make sure the Power Switch is in
the “OFF” ( O ) position and the unit is
unplugged.
1. Firmly grasp the brush cartridge from the
side of the unit and pull out from the unit.
2. To remove any debris that may have
collected around the dual PowerBrushes,
rinse the brush cartridge under
warm water.
3. Replace the brush cartridge into the unit
by gently guiding the cartridge in the unit.
Once it is in place, firmly “snap” the brush
cartridge in place.
NOTE: Do not attempt to remove or insert
the brush cartridge while the unit is
running. This will damage your unit.
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
8
Maintenance and care (continued)
Storage
Store in a dry area, at room temperature
to avoid freezing.
Tip:
If you do not have the Brush
Cartridge in all the way, the
Dual PowerBrushes will not
rotate. Firmly push the
cartridge in place, while
listening for the “snap” to
assure proper placement.
To replace the powerbrush belt
If the belt should break, to replace:
1.
1. Remove the screw in the belt cover using a
Phillips Screwdriver.
2. Remove the broken belt.
3. Replace the new belt over the 2 belt gears.
4. Replace the belt cover door.
WARNING:
To reduce the risk of
fire, electric shock or
injury, unplug from outlet
before servicing.
Troubleshooting
Cleaner won’t run
Possible causes
Remedies
1. Power cord not plugged in
1. Check electrical plug
2. Blown fuse/tripped breaker
3. C.I.D. needs to be reset
2. Check/replace fuse or reset breaker.
3. Reset C.I.D. (page 5).
Reduced spray or no spray
Possible causes
Remedies
1. Spray nozzle clogged
1. Clean spray nozzle
2. Solution tank empty
2. Check/refill tank
3. Tank not inserted properly
3. Make sure tank is inserted properly
Deep cleaner won't pick up cleaning solution
Possible causes
Remedies
1. Collection tank is full
1. Empty collection tank
2. Collection tank drain plug is loose
2. Check plug for snug fit
9
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Troubleshooting (continued)
Dual PowerBrushes are not rotating
Possible causes
Remedies
1. Removable cartridge not inserted
1. Make sure to firmly "snap" the
properly/all the way
brush cartridge in place
2. Broken belt
2. Replace belt (page 9)
Water coming out of vents
Possible causes
Remedies
1. Tank is past full line
1. Empty tank
2. Unit may be tipped upright causing dirty
2. Empty collection tank
water to leak from collection tank
Other maintenance or service not included in the manual should be performed by an
authorized service representative.
Thank you for selecting a BISSELL product.
If you should happen to need assistance during assembly or operation, call 1-800-237-7691.
Please do not return this product to the store.
For any questions or concerns, BISSELL is happy to be of service.
Contact us directly at 1-800-237-7691.
BISSELL Consumer Services
For information about repairs or replacement parts, or questions about your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
Saturday
Or write:
8 a.m. — 10 p.m. ET
9 a.m. — 8 p.m. ET
BISSELL HOMECARE, INC
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com or www.2Xbissell.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event
of a warranty claim. See Warranty on page 12 for details.
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
10
Replacement parts
Item
1
Part No.
203-2557
Part Name
Solution tank w/cap
2
3
4
5
6
7
8
203-2552
203-2554
203-2514
203-2517
203-2537
79B9
Collection/solution tank cap
Collection tank w/cap
Brush cartridge
Belt Cover
Belt
2X Little Green® Formula 32 oz.
2X Little Green® Formula 16 oz.
2X Pet Stain & Odor Formula 32 oz.
2X Pet Stain & Odor Formula 16 oz.
79B9-1
9
74R7
10
74R7-1
1
6
2
3
4
5
7/8
9/10
Please register your new BISSELL product at
Earn Rewards Points!
To qualify you for discounts, rebates, and other BISSELL perks.
11
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Warranty - BISSELL Spot Lifter® PowerBrush
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to
state. If you need additional instruction regarding this warranty or have questions regarding what it may cover,
please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.
Keep your original sales receipt — it is your proof of warranty.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL
Homecare, Inc. will repair or replace (with new or remanufactured components or products), at BISSELL’s option,
free of charge from the date of purchase by the original purchaser, for one year any defective or
malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply
to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negli-
gence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is
not covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about your warranty,
contact BISSELL Consumer Services.
Website or E-mail:
Or visit: www.2Xbissell.com
Or call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
Or Write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE
ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE
OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES
EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY
OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR
DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty lasts, so
the above limitation may not apply to you.
©2009 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 120-4146
Rev 10/09
Visit our website at:
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
12
|