Black Decker Work Light 90515795 User Manual

SL102B_ManualEN_051007.qxp 5/10/07 9:13 AM Page i  
V-1 MILLION POWER SERIES SPOTLIGHT  
INSTRUCTION MANUAL  
Catalog Number SL102B  
Thank you for choosing Black & Decker!  
Go to www.BlackandDecker.com/NewOwner  
to register your new product  
BEFORE RETURNING THIS PRODUCT  
FOR ANY REASON PLEASE CALL  
1-800-544-6986  
BEFORE YOU CALL, HAVE THE CATALOG No, AND DATE CODE  
AVAILABLE. IN MOST CASES, A BLACK & DECKER REPRESENTATIVE  
CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE A  
SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS  
VITAL TO BLACK & DECKER.  
TO REDUCE THE RISK OF INJURY, THE USER MUST READ AND  
UNDERSTAND THE INSTRUCTION MANUAL  
SAVE THIS MANUAL FOR FUTURE REFERENCE.  
Cat. # SL102B  
April ’07  
Form # 90515795  
Copyright © 2007 Black & Decker  
Printed in China  
 
SL102B_ManualEN_051007.qxp 5/10/07 9:13 AM Page 2  
• EXTENSION CORDS. Make sure your extension cord is in good condition. When using an  
extension cord, be sure to use one heavy enough to carry the current your product will draw. An  
undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The  
following table shows the correct size to use depending on cord length and nameplate ampere  
rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.  
SAFETY GUIDELINES / DEFINITIONS  
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.  
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.  
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.  
CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided,  
may result in property damage.  
RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions should always be  
followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or  
equipment could result in serious injury and property damage. There are certain applications for which tools  
and equipment are designed. Black & Decker strongly recommends that this product NOT be modified and/or  
used for any application other than for which it was designed. Read and understand all warnings and operating  
instructions before using any tool or equipment.  
SAVE THESE INSTRUCTIONS  
THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR THE V-1 MILLION  
POWER SERIES SPOTLIGHT MODEL SL102B.  
WARNING: TO REDUCE THE RISK OF INJURY:  
• Follow these instructions and those published by the manufacturer of any equipment you intend to use with  
this unit. Review cautionary markings on these products.  
IMPORTANT SAFETY INSTRUCTIONS  
WARNING: This product or its power cord contains lead, a chemical known to the State of California to  
cause cancer and birth defect or other reproductive harm. Wash hands after handling.  
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK:  
Do not plug in a power supply without the bulb lens and cover in place.  
WARNING: FIRE HAZARD: Never contact combustible material to the lens and never tape or tie the switch in  
the on position.  
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:  
• All halogen lights give off heat:  
– Do not touch lens while operating.  
– Keep combustibles away from spotlight lens. Extreme heat can cause fires.  
– Never place the light face-down on any surface when lit.  
• Never look directly into the light or shine the light into another person’s eyes.  
• Keep sharp objects away from lens — it is glass and can break.  
• Do not immerse spotlight in water.  
• Do not drop or throw spotlight. It contains glass and a sealed lead acid battery.  
• Only replace bulb with type indicated in specifications (6 volt, H3 55 watt quartz halogen).  
• Use only with AC or DC charging adapters that are provided with unit. Plug in the charging adapter at the  
spotlight first, then plug into the charging source.  
• Do not overcharge:  
– AC recharge up to 14 hours maximum.  
– DC recharge up to 14 hours maximum.  
• NEVER ATTEMPT TO USE THE AC CHARGER AND DC CHARGING PORT SIMULTANEOUSLY.  
• After charging/recharging, disconnect charging adapter or extension cord and wait 5 minutes before use.  
• Do not crush, cut, pull or expose charging adapter cords to extreme heat.  
2
 
SL102B_ManualEN_051007.qxp 5/10/07 9:13 AM Page 3  
• Position charging adapter cords so they do not become entangled or become a safety hazard. Keep charging  
adapter cords away from sharp edges.  
• Use in a dry location only.  
• Do not open body casing. There are no user-serviceable parts inside.  
• To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting from the  
120 Volt AC Charger.  
• Do not attempt to charge the unit if the 120 Volt AC Charger plug is damaged— return the unit to  
manufacturer for repair.  
INTRODUCTION  
Thank you for choosing the Black & Decker® V-1 Million Power SeriesSpotlight. Please read this  
guide carefully before use to ensure optimum performance and to avoid damage to the unit.  
FEATURES  
• Powerful, focused quartz halogen beam  
• Protective rubber safety guard (bezel) around lens  
• Rubber safety cap protects battery compartment  
• Comfortable pistol grip  
• Battery Status LED Indicator  
• UL listed, built-in 120 volt AC charger that works with a standard household extension cord (not included)  
• 12 volt DC charging adapter included  
• Rechargeable, non-spillable, sealed lead acid battery  
RUBBER BEZEL  
BATTERY STATUS LED  
INDICATOR  
120 VOLT AC CHARGER  
(BACK OF UNIT)  
QUARTZ HALOGEN BULB  
DC CHARGING  
PORT  
TRIGGER ON/OFF  
TRIGGER LOCK  
PISTOL GRIP HANDLE  
CHARGING/RECHARGING THE SPOTLIGHT  
This unit is shipped in a partially charged state. Charge unit BEFORE first use using the 120 Volt AC  
Charger for 12-14 hours or until the red Battery Status LED flashes. Charge after each use until red  
LED flashes.  
Charging/Recharging Using the 120 Volt AC Charger and a Standard Household  
Extension Cord (not included)  
Plug a standard North American 120 volt AC extension cord (not included) into the 120 Volt AC  
Charger on the back of the unit.  
BATTERY STATUS LED  
INDICATOR  
BUILT-IN 120V AC  
CHARGER  
Make sure the Spotlight is OFF (the Trigger Lock is in the OFF position and the Trigger is not depressed).  
3
 
SL102B_ManualEN_051007.qxp 5/10/07 9:13 AM Page 4  
Charge until the Battery Status LED Indicator red LED flashes (approximately 12-14 hours). DO NOT  
CHARGE FOR LONGER THAN 14 HOURS.  
Charging/Recharging Using the 12 Volt DC Charging Adapter  
Plug the barrel tip of the supplied 12 Volt DC Charging Adapter into the 12 Volt DC Charging Port.  
12 VOLT DC CHARGING  
PORT  
12 VOLT DC CHARGING ADAPTER  
Insert the 12 volt DC plug end into the accessory outlet of your vehicle or other 12 volt DC power source.  
Make sure the Spotlight is OFF (the Trigger Lock is in the OFF position and the Trigger is not depressed).  
Charge until the Battery Status LED Indicator red LED flashes (approximately 12-14 hours). DO NOT  
CHARGE FOR LONGER THAN 14 HOURS.  
Make sure the DC source (jump-starter, battery pack, vehicle accessory outlet, etc.) is 12 volt DC  
and is able to supply at least one half amp at 12 volt DC for 8 hours. This means a battery pack  
should be charged with at least 4 amp hours capacity.  
Note: When using a vehicle’s 12 volt DC accessory outlet as a charging source, be aware that some  
vehicles require you to turn on the ignition to power the accessory outlet.  
WARNING: NEVER ATTEMPT TO USE THE AC CHARGER AND DC CHARGING PORT SIMULTANEOUSLY.  
OPERATING INSTRUCTIONS  
To turn the Spotlight ON, depress the Trigger. To lock the  
Trigger in the ON position, depress the Trigger, then slide  
TRIGGER  
the Trigger Lock up. The spotlight will stay on until the  
lock is moved to the OFF position and the trigger is  
released.  
TRIGGER LOCK  
CARE AND MAINTENANCE  
All batteries lose charge with time, especially when they are warm. Recharge the unit every two  
months when not in frequent use, preferably using the 120 volt AC method.  
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the spotlight unit  
with a soft cloth moistened with a mild solution of water and detergent.  
The quartz halogen bulb is the only user-replaceable part in the Spotlight. Periodically inspect the  
condition of adapters, connectors and wires. Contact Technical Support toll-free at 1-800-544-6986 to  
replace any components that have become worn or broken.  
Spotlight Bulb Replacement  
To replace the bulb, you will need a small Phillips screwdriver and a 6 volt H3 55 watt replacement bulb.  
During installation, avoid touching the glass part of the bulb. Bulb life may be shortened by installing a  
bulb with dirt or fingerprints on it. The bulb can be wiped clean with a cloth moistened with alcohol.  
QUARTZ HALOGEN  
BULB  
RUBBER  
END CAP  
TRIGGER  
SWITCH  
REFLECTOR  
TRIGGER LOCK  
RUBBER  
RETAINING RING  
“O” RING  
RUBBER BEZEL COVER  
4
 
SL102B_ManualEN_051007.qxp 5/10/07 9:13 AM Page 5  
1. Disconnect the unit from any charging adapters.  
2. Push the rubber bezel forward toward the front of the spotlight to reveal two small Phillips screws in  
the retaining ring.  
3. Using the screwdriver, remove (counterclockwise) the two screws. Set them aside.  
4. Lift off the retaining ring, glass lens and rubber “O” ring and set them aside.  
5. Carefully remove the reflector and bulb assembly.  
HAIRPIN RETAINING  
WIRES  
PHILLIPS  
HEAD  
SCREWS  
BULB  
REFLECTOR  
6. Disconnect the bulb wire from the red power wire.  
7. Unsnap the hairpin retaining wires from the reflector’s flange.  
8. Using the screwdriver, loosen the retaining screw to remove the bulb from the reflector (no need  
to completely remove this screw).  
9. Lift out the bulb and detach wire.  
10. Insert the replacement bulb into the reflector’s flange.  
11. Put back and secure the hairpin retaining wires.  
12. Connect the bulb power wire to the red power wire.  
13. Tighten the retaining screw on the flange.  
14. Place the reflector in position in the body of the spotlight.  
15. Replace the rubber “O” ring in the groove around the perimeter of the reflector.  
16. Replace glass and retaining ring so the screw holes are aligned.  
17. Secure retaining ring with two screws.  
18. Replace rubber bezel.  
19. Operate switch to ensure proper operation of spotlight.  
WARNING: To reduce the risk of electric shock, replace bulb with 6 volt H3 55 watt only.  
Battery Replacement/Disposal  
Battery Replacement  
The battery should last the service life of the unit. Contact Technical Support toll-free at 1-800-544-  
6986 for any information you may need.  
Safe Battery Disposal  
Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be disposed  
of properly. Recycling is required, contact your local authority for information. Failure to  
comply with local, state and federal regulations can result in fines, or imprisonment.  
WARNINGS:  
• Do not dispose of the battery in fire as this may result in an explosion.  
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to  
prevent shorting (shorting can result in injury or fire).  
• Do not expose battery to fire or intense heat as it may explode.  
• For more information on recycling this battery, call toll-free (877) 288-7722.  
5
 
SL102B_ManualEN_051007.qxp 5/10/07 9:13 AM Page 6  
TROUBLESHOOTING  
The Battery Status Indicator LED Does Not Light When Charging  
1. Check connection to the 120 Volt AC Charger or 12 Volt DC Charging Port.  
2. Check connection to AC or DC power source.  
3. Confirm there is a functioning AC or DC current.  
Unit Will Not Operate  
1. The Spotlight will not operate when charging. Be sure all adapters are disconnected before  
Spotlight use.  
2. If you suspect the bulb is blown, check the filament. If the filament is coiled and unbroken, the  
bulb is not blown. If bulb is blown, replace it.  
3. The battery may be completely discharged. Charge the unit following the directions on page 3.  
4. If the Spotlight does not operate after recharging as directed, contact Technical Support toll-free  
at 1-800-544-6986.  
For assistance with your product, visit our website www.blackanddecker.com for the location of the  
service center nearest you or call the BLACK & DECKER help line at 1-800-544-6986.  
Accessories  
Recommended accessories for use with your tool are available from your local dealer or authorized  
service center. If you need assistance regarding accessories, please call: 1-800-544-6986.  
WARNING: The use of any accessory not recommended for use with this tool could be hazardous.  
SERVICE INFORMATION  
All Black & Decker Service Centers are staffed with trained personnel to provide customers with  
efficient and reliable power tool service. Whether you need technical advice, repair, or genuine  
factory replacement parts, contact the Black & Decker location nearest you. To find your local  
service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-544-6986 or  
FULL TWO-YEAR HOME USE WARRANTY  
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or  
workmanship. The defective product will be replaced or repaired at no charge in either of two ways.  
The first, which will result in exchanges only, is to return the product to the retailer from whom it  
was purchased (provided that the store is a participating retailer). Returns should be made within  
the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of  
purchase may be required. Please check with the retailer for their specific return policy regarding  
returns that are beyond the time set for exchanges.  
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized  
Service Center for repair or replacement at our option. Proof of purchase may be required. Black &  
Decker owned and authorized Service Centers are listed under "Tools-Electric" in the yellow pages of  
This warranty does not apply to accessories. This warranty gives you specific legal rights and you  
may have other rights which vary from state to state or province to province. Should you have any  
questions, contact the manager of your nearest Black & Decker Service Center. This product is not  
intended for commercial use.  
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call  
1-800-544-6986 for a free replacement.  
6
 
SL102B_ManualEN_051007.qxp 5/10/07 9:13 AM Page 7  
SPECIFICATIONS  
Spotlight Bulb:  
Battery:  
6 volt, H3 series, 55 watt  
Maintenance-free, sealed lead acid,  
6 volt, 3 amp hour  
AC Charger:  
DC Plug Fuse:  
UL Listed Class 2, 12 volt DC (300 mA)  
0.5A/250 V  
Imported by  
Black & Decker (U.S.) Inc.,  
701 E. Joppa Rd.  
Towson, MD 21286 U.S.A.  
Vector Products, Inc.  
4140 S.W. 30th Ave.  
Fort Lauderdale, FL 33312  
7
 

Black Decker Kitchen Grill IG100 User Manual
Blaupunkt Car Stereo System RDM 127 User Manual
Bodum Mixer 11381 User Manual
Bosch Appliances Oven WALL OVENS User Manual
Bradley Smoker Plumbing Product WS 1X User Manual
Bryan Boilers Boiler CL Series User Manual
Califone Headphones 3068AV User Manual
Capcom Games MotoGP08 User Manual
Casio Computer Hardware CS 53P User Manual
Chevrolet Automobile 2004 TRACKER User Manual