Bosch Appliances Radio LE10 User Manual

LE10 Radio Receiver  
CRS-URE-0100 | F.01U.278.517 | V2.0 | 2012.11  
en User Manual  
 
LE10 Radio Receiver  
Table of Contents | en  
3
Table of Contents  
Safety instructions  
General safety instructions  
Environmental conditions  
Electrostatic Discharge (ESD)  
Product information  
General description  
Compatible transmitters  
Main applications  
Description of the different modes  
Installation  
Unpacking  
Connecting the power supply  
Power supply with the RJ12 power socket  
Power supply connected to a wired installation  
Wall installation  
Connection compartment  
Connecting ports  
Mode selection  
Mode indication after power on  
Programming  
Enter programming mode  
Program a transmitter in modes 1, 2 or 5  
Delete a transmitter  
Delete all transmitters  
Program a door address in modes 3 or 4  
Programming in modes 6 or 7  
Operation  
Standby mode  
Standby with no transmitter programmed  
Standby with at least one transmitter programmed  
Bosch Security Systems  
User Manual  
F.01U.278.517 | V2.0 | 2012.11  
 
4
en | Table of Contents  
LE10 Radio Receiver  
Normal mode (modes 1 and 2)  
Activation of a transmitter in normal mode  
Dementia (mode 3)  
Activation of a MIYS37L Wristband Transmitter  
Detection of a MIYS37E Wristband Transmitter alone  
Detection of a MIYS37L Wristband Transmitter with a MIYS37E  
Wristband Transmitter nearby  
Dementia with Accompany (mode 4)  
Activation of a MIYS37L Wristband Transmitter  
Remote control (mode 5)  
Activation of a programmed transmitter  
Activation of a programmed transmitter with a battery-low  
message or with a new battery  
Open receiver (modes 6 and 7)  
Activation of a transmitter in the reception range  
Daily messages in modes 1, 2 or 5  
Daily message with battery-low signal  
Reset of a battery-low indication with button T1  
Extended MIYN46 (mode 8, only with SW 1.10)  
Dual channel receiver (mode 9, only with SW 1.10)  
Technical data  
F.01U.278.517 | V2.0 | 2012.11  
User Manual  
Bosch Security Systems  
 
LE10 Radio Receiver  
Safety instructions | en  
5
1
Safety instructions  
1.1  
General safety instructions  
Installation and initial operation should only be carried out by  
trained service personnel.  
1.2  
Environmental conditions  
The LE10 Radio Receiver must not be located near a water tap  
or any other source of water. The electrical safety of the LE10  
Radio Receiver is only guaranteed if the electrical installation is  
in accordance with the national regulations and if this  
installation works properly. The LE10 Radio Receiver may not  
be used in buildings prone to fire and explosion hazards.  
The LE10 Radio Receiver may not be used under exposure to  
direct sunlight, to heat, to dust or to an excessive humidity  
(only use the equipment in a clean environment).  
1.3  
Electrostatic Discharge (ESD)  
WARNING!  
The LE10 Radio Receiver contains highly sensitive electronic  
components. It should be opened only in an ESD protected  
environment with respect to the following precautions.  
Discharge yourself from electrostatic loads by touching a  
grounded conductive surface before opening the unit. Avoid  
touching conductive parts inside the LE10 Radio Receiver if not  
absolutely necessary.  
Bosch Security Systems  
User Manual  
F.01U.278.517 | V2.0 | 2012.11  
 
       
6
en | Product information  
LE10 Radio Receiver  
2
Product information  
2.1  
General description  
The LE10 Radio Receiver is designed to receive radio signals  
from different Bosch radio transmitters at the frequency of  
434.01 MHz. After receiving radio signals from either  
programmed or not programmed wireless transmitters, the  
LE10 Radio Receiver reacts by activating its two green and red  
LEDs and by switching relay outputs of two relays.  
LED 1 (green)  
LED 2 (red)  
Figure 2.1 Front view of the LE10 Radio Receiver  
2.2  
Compatible transmitters  
All of the following Bosch wireless transmitters are compatible  
with the LE10 Radio Receiver:  
MIYS37 Wristband Transmitters  
MIYS37L Wristband Transmitters with Locating function  
MIYS37E Wristband Transmitters with Accompany function  
MIYS35 Pendant Transmitters  
MIYMD ManDown Sensors  
MIYRAC Wireless Contact  
F.01U.278.517 | V2.0 | 2012.11  
User Manual  
Bosch Security Systems  
 
     
LE10 Radio Receiver  
Product information | en  
7
2.3  
Main applications  
LE10 Radio Receiver as small stand alone call system  
After receiving a radio signal from a programmed radio  
transmitter, the relay output switches a siren or a lamp to  
indicate locally a wireless call.  
LE10 Radio Receiver connected to a emergency call system  
via relay contact  
After receiving a radio signal from a programmed radio  
transmitter, the relay will be switched. This relay output is  
connected to a wired emergency call system by wire and hereby  
a call will be generated or forwarded.  
LE10 Radio Receiver as part of a Resident Alert System  
monitoring dementia  
After receiving a signal from a dementia transmitter, the relay  
will be activated to close a monitored door.  
2.4  
Description of the different modes  
Mode Name  
Description  
1
Normal  
20 wireless transmitters can be programmed.  
Calls are indicated by the red LED and Relay 1.  
A battery-low signal is indicated by the red  
LED and Relay 2.  
2
3
Normal, with red LED The same functions as in mode 1 are available,  
deactivated at except for the battery-low signal which is not  
battery-low indication indicated by the red LED, but only by Relay 2.  
Dementia  
The MIYS37L and MIYS37E wireless  
transmitters are detected. Relay 1 can be used  
to lock a monitored door. Relay 2 can be used  
to interrupt a monitoring loop.  
Bosch Security Systems  
User Manual  
F.01U.278.517 | V2.0 | 2012.11  
 
   
8
en | Product information  
LE10 Radio Receiver  
Mode Name  
Description  
4
Dementia with  
Accompany  
This mode allows to connect the LE10 Radio  
Receiver to a wired emergency call system, in  
which the Accompany function can be  
implemented. It will wait 10 seconds after  
receiving a signal from a MIYS37L transmitter.  
If it detects a MIYS37E transmitter in this lapse  
of time, no alarm is generated. If not, Relay 1 is  
activated for 2 seconds.  
5
6
7
8
9
Remote control  
Open receiver  
20 wireless transmitters can be programmed.  
Per sequence, only the same transmitter can  
switch on and off the Relay1. A battery-low  
signal is indicated by the red LED and Relay 2.  
No wireless transmitter needs to be  
programmed. Any transmitter within reception  
range of the LE10 Radio Receiver can activate  
the device.  
Open receiver with  
reduced range  
Same functions as in mode 6, but with  
reduced range. This functionality is designed  
to improve reception of transmitters located  
closer to the LE10 Radio Receiver.  
Extended MIYN46  
transmitter  
Additional MIYN46 transmitters can be  
programmed. Behavior is similar to normal  
mode 1, with certain differences according to  
the transmitter that is activated.  
programming  
(only with SW 1.10)  
Dual channel receiver Only MIYS37 wireless transmitters can be  
(only with SW 1.10)  
programmed. Calls are indicated by Relay 1 or  
Relay 2, according to the slot in which the  
MIYS37 wireless transmitter is programmed. A  
battery-low signal is indicated by the red LED.  
NOTICE!  
Factory setting is normal mode 1, in which 20 wireless  
transmitters can be programmed. Calls are indicated by the red  
LED and Relay 1. A battery-low signal is indicated by the red  
LED and Relay 2.  
F.01U.278.517 | V2.0 | 2012.11  
User Manual  
Bosch Security Systems  
 
LE10 Radio Receiver  
Installation | en  
9
3
Installation  
3.1  
Unpacking  
The LE10 Radio Receiver is carefully packed for transportation.  
The components contained in the box are protected, but should  
be handled with care. Store the packaging material for further  
use (storage or transport). In case of defective or missing  
equipment, do not try to install the LE10 Radio Receiver.  
Contact immediately your local representative.  
1. Take all components out of the box and place the LE10 Radio  
Receiver on the working space.  
2. Check that the following accessories are delivered: the  
fixings (2 screws and 2 screw anchors) and this user manual.  
3. Check that the LE10 Radio Receiver and its accessories have  
not been damaged during transportation.  
3.2  
Connecting the power supply  
There are two different ways to connect the power supply of  
the LE10 Radio Receiver. After connection, the LE10 Radio  
Receiver will be in standby mode.  
3.2.1  
Power supply with the RJ12 power socket  
The LE10 Radio Receiver can be powered by a power supply  
unit (PSU). The PSU should be plugged in the RJ12 socket on  
the rear side of the unit and should be easily accessible at any  
time. See Section 4.1 Connecting ports, page 11 for access to  
information about the power supply.  
3.2.2  
Power supply connected to a wired installation  
The LE10 Radio Receiver can be powered by connecting a wired  
input into poles 1 and 2 of the connection board. See  
Section 4.1 Connecting ports, page 11 for information about the  
power supply.  
Bosch Security Systems  
User Manual  
F.01U.278.517 | V2.0 | 2012.11  
 
         
10 en | Installation  
LE10 Radio Receiver  
3.3  
Wall installation  
You can fasten the LE10 Radio Receiver on a smooth wall  
surface using two screws. Installation cables should be placed  
inside the cable channels on the bottom.  
3.4 in (80 mm)  
2.2 in (53.8 mm)  
0.51 in  
(13.1 mm)  
0.15 in  
(3.7 mm)  
0.63 in (16 mm)  
0.26 in (6.6 mm)  
1.06 in (27 mm  
5.16 in (131 mm)  
2.36 in (59.9 mm)  
0.71 in (18.1 mm)  
1.62 in  
(26 mm)  
0.15 in  
(3.7 mm)  
0.08 in  
(2 mm)  
Figure 3.1 Dimensions of the backside of the LE10 Radio Receiver  
F.01U.278.517 | V2.0 | 2012.11  
User Manual  
Bosch Security Systems  
 
 
LE10 Radio Receiver  
Connection compartment | en 11  
4
Connection compartment  
4.1  
Connecting ports  
To open the device:  
hold the LE10 Radio Receiver in one hand, facing you, so  
that you can see the Bosch logo and the two LEDs.  
grab the connection compartment housing with the other  
hand and slide it towards you.  
you can now see the components as in the following  
illustration:  
Relay 2  
output  
ON  
OFF  
S3  
Relay 1  
output  
1 2 3 4 5  
6
1
T1  
P133  
RJ12  
+
8 - 30 VDC  
6
5
4
3
2
1
+
Relay 1 output  
Figure 4.1 LE10 Radio Receiver connection compartment  
NOTICE!  
The standby conditions of Relay 1 and Relay 2 are as shown in  
this illustration.  
Bosch Security Systems  
User Manual  
F.01U.278.517 | V2.0 | 2012.11  
 
   
12 en | Connection compartment  
LE10 Radio Receiver  
4.2  
Mode selection  
Modes 1 to 9 can be selected by operating switches 1 to 5 of  
the 5-digits micro switch S3.  
CAUTION!  
After selecting the mode, disconnect the power supply and  
connect it again.  
Mode Description  
Switch number  
1
2
3
4
5
1
2
Normal mode  
off off off off off  
on off off off off  
Normal mode, with the red LED  
deactivated at battery-low indication  
3
4
5
6
7
8
9
Dementia mode  
off on off off off  
on on off off off  
off off on off off  
on off on off off  
off on on off off  
on on on off off  
Dementia with Accompany mode  
Remote control  
Open receiver  
Open receiver with reduced range  
Extended N46 (only with SW 1.10)  
Dual channel receiver (only with SW 1.10) off off off on off  
NOTICE!  
Factory setting is all switches set to off.  
4.2.1  
Mode indication after power on  
When the power supply is connected to the LE10 Radio  
Receiver, the green LED will light up permanently for 2  
seconds. Afterwards, the device will display the current  
mode through the green LED, by blinking as many times as  
the number of the mode. The green LED will then light up  
permanently.  
Example: In mode 8, the green LED will blink 8 times.  
When changing the mode, all programmed transmitters will  
be deleted.  
F.01U.278.517 | V2.0 | 2012.11  
User Manual  
Bosch Security Systems  
 
   
LE10 Radio Receiver  
Programming | en 13  
5
Programming  
5.1  
Enter programming mode  
To enter programming mode, press simply button T1 for the  
NOTICE!  
Both relays will not be activated in the programming mode.  
5.2  
Program a transmitter in modes 1, 2 or 5  
NOTICE!  
Per programming sequence only one transmitter can be  
matched. You can program up to 20 transmitters.  
To start programming  
Press button T1 for min. 1 second and max. 3 seconds.  
Device behavior  
The green LED stays permanently on.  
The red LED blinks slowly for maximum 30 seconds.  
Within these 30 seconds, activate the transmitter that you want  
to match, the following behavior should be observed:  
The green LED and the red LED blink alternating for 6  
seconds.  
This indication confirms that the transmitter is programmed.  
If the transmitter is already programmed, then the red LED  
blinks fast for 6 seconds after activating the transmitter.  
If 20 transmitters are already programmed, then the red  
LED blinks fast for 10 seconds directly after activating the  
button T1 between 1 and 3 seconds.  
You can repeat the sequence with another transmitter.  
Bosch Security Systems  
User Manual  
F.01U.278.517 | V2.0 | 2012.11  
 
     
14 en | Programming  
LE10 Radio Receiver  
5.3  
Delete a transmitter  
NOTICE!  
Per sequence only one transmitter can be deleted.  
To start deleting:  
Press button T1 for min. 5 seconds and max. 10 seconds.  
Device behavior  
The green LED stays permanently on, then after 5 seconds  
blinks fast 5 times.  
The red LED stays off and then blinks for 30 seconds.  
Within these 30 seconds, activate the transmitter that you want  
to delete, the following behavior should be observed:  
The green LED stays permanently on.  
The red LED stays permanently on for 5 seconds and then  
turns off.  
This indication confirms that the transmitter is deleted. You can  
repeat the sequence with another transmitter.  
5.4  
Delete all transmitters  
To start deleting  
Press button T1 for minimum 20 seconds and maximum 40  
seconds.  
Device behavior  
The green LED stays permanently on, then after 5 seconds,  
blinks fast 5 times. After 20 seconds, the green LED will  
blink for 20 seconds.  
At that moment, the red LED lights up permanently for 5  
seconds then turns off.  
This indication confirms that all transmitters are then deleted.  
NOTICE!  
If button T1 is pressed longer than 40 seconds, then the LE10  
Radio Receiver will jump out of the programming mode.  
F.01U.278.517 | V2.0 | 2012.11  
User Manual  
Bosch Security Systems  
 
   
LE10 Radio Receiver  
Programming | en 15  
5.5  
Program a door address in modes 3 or 4  
You can program a door address stored in a MIYS37L Wristband  
Transmitter with Locating function, in modes 3 or 4.  
NOTICE!  
A door address must be stored beforehand in a MIYS37L  
Wristband Transmitter with Locating function.  
NOTICE!  
Only one door address of a MIYS37L Wristband Transmitter  
with Locating function can be matched in the LE10 Radio  
Receiver.  
To start programming  
Press button T1 min. 1 second and max. 3 seconds.  
Device behavior  
The green LED stays permanently on.  
The red LED blinks slow for max. 30 seconds.  
Activate the S37L Wristband Transmitter, which you desire  
to match, before the end of the 30 seconds.  
Upon activating the transmitter, the green LED and the red  
LED blink alternating quick for 6 seconds.  
This indication confirms that the door address in the MIYS37L  
Wristband Transmitter is matched in the LE10 Radio Receiver.  
CAUTION!  
When a new door address stored in a MIYS37L Wristband  
Transmitter is programmed, it overwrites the current door  
address.  
5.5.1  
Programming in modes 6 or 7  
It is neither possible nor necessary to program a transmitter in  
modes 6 or 7 (Open Receiver).  
Bosch Security Systems  
User Manual  
F.01U.278.517 | V2.0 | 2012.11  
 
   
16 en | Operation  
LE10 Radio Receiver  
6
Operation  
6.1  
Standby mode  
The LE10 Radio Receiver enters standby mode when the power  
supply is connected. Both relays are off. See Section 4.2.1 Mode  
6.1.1  
6.1.2  
Standby with no transmitter programmed  
Device behavior  
The green LED stays permanently on.  
The red LED blinks 3 times every 10 seconds.  
Standby with at least one transmitter programmed  
Device behavior  
The green LED stays permanently on.  
The red LED stays permanently off.  
6.2  
Normal mode (modes 1 and 2)  
6.2.1  
Activation of a transmitter in normal mode  
Device behavior  
The green LED stays permanently on.  
When a matched transmitter is activated:  
The red LED lights up permanently for 10 seconds.  
Relay 1 switches on for 10 seconds.  
Relay 2 stays off.  
If the same or another matched transmitter is activated within  
10 seconds, the alarm will be retriggered for 10 seconds.  
Device behavior when a transmitter has a low battery  
The green LED stays permanently on.  
When the transmitter is activated:  
The red LED blinks twice for 2 seconds, then lights up  
permanently for 8 seconds. It then blinks once every 10  
seconds.  
Relay 1 switches on for 10 seconds.  
F.01U.278.517 | V2.0 | 2012.11  
User Manual  
Bosch Security Systems  
 
             
LE10 Radio Receiver  
Operation | en 17  
Relay 2 switches on permanently until the battery is  
replaced and the transmitter is activated again.  
NOTICE!  
In normal mode 2, the red LED is deactivated regarding battery-  
low indication and will not blink every 10 seconds.  
Device behavior when the battery is replaced in a transmitter  
The green LED stays permanently on.  
When the transmitter is activated:  
The red LED stops blinking every 10 seconds, and lights up  
permanently for 10 seconds.  
Relay 1 switches on for 10 seconds.  
Relay 2 switches off.  
6.3  
Dementia (mode 3)  
6.3.1  
Activation of a MIYS37L Wristband Transmitter  
Device behavior  
The green LED stays permanently on.  
When a MIYS37L transmitter is activated:  
The red LED lights up permanently for 7 seconds.  
Relay 1 switches on for 7 seconds.  
1 second after Relay 1, Relay 2 switches on for 3 seconds.  
The procedure is repeated if a MIYS37L transmitter is activated  
again.  
Device behavior when a MIYS37L transmitter has a low  
battery  
The green LED stays permanently on.  
When the MIYS37L transmitter is activated:  
The red LED blinks twice for 2 seconds and then lights up  
permanently red for 5 seconds.  
Relay 1 and Relay 2 behave as above.  
Bosch Security Systems  
User Manual  
F.01U.278.517 | V2.0 | 2012.11  
 
   
18 en | Operation  
LE10 Radio Receiver  
6.3.2  
Detection of a MIYS37E Wristband Transmitter  
alone  
Device behavior  
The green LED stays permanently on.  
When a MIYS37E transmitter is detected:  
The red LED lights up permanently for 30 seconds.  
Relay 1 stays off for 30 seconds.  
Relay 2 switches on for 25 seconds.  
During these 30 seconds, all radio reception is fully blocked.  
This allows a person wearing the MIYS37E to cross the  
monitored area without generating an accompany signal.  
6.3.3  
Detection of a MIYS37L Wristband Transmitter  
with a MIYS37E Wristband Transmitter nearby  
Device behavior  
The green LED stays permanently on.  
When a MIYS37L transmitter and a MIYS37E transmitter are  
detected by the monitored area:  
The red LED lights up permanently.  
Relay 1 switches on until the MIYS37E transmitter is  
detected.  
1 second after Relay 1, Relay 2 switches on for 3 seconds.  
When the MIYS37E transmitter sends its signal (approx. 4  
seconds after the MIYS37L):  
The red LED lights up permanently for 30 seconds.  
Relay 1 switches off for 30 seconds.  
Relay 2 stays on for another 25 seconds.  
After the detection of the MIYS37E transmitter, all radio  
reception is fully blocked during 30 seconds. This allows a  
person wearing the MIYS37E transmitter to accompany a  
person wearing the MIYS37L transmitter through the monitored  
area without generating an accompany signal.  
F.01U.278.517 | V2.0 | 2012.11  
User Manual  
Bosch Security Systems  
 
   
LE10 Radio Receiver  
Operation | en 19  
6.4  
Dementia with Accompany (mode 4)  
6.4.1  
Activation of a MIYS37L Wristband Transmitter  
Device behavior  
The green LED stays permanently on.  
When a MIYS37L transmitter is activated, a 10-second time slot  
starts.  
If, during these 10 seconds, a MIYS37E transmitter is detected:  
There is no change of the LEDs and the relays.  
If, during these 10 seconds, no MIYS37E transmitter is  
detected:  
The red LED lights up for 2 seconds.  
Relay 1 switches on for 2 seconds.  
Relay 2 stays off.  
NOTICE!  
In mode 4, there is no battery-low indication.  
6.5  
Remote control (mode 5)  
6.5.1  
Activation of a programmed transmitter  
Device behavior  
The green LED stays permanently on.  
The red LED lights up.  
Relay 1 switches on.  
Relay 2 stays off.  
When the same transmitter is activated again:  
The red LED turns off.  
Relay 1 switches off.  
NOTICE!  
No other transmitter is able to switch the Relay 1 off, when it  
has been already switched on by a transmitter.  
Bosch Security Systems  
User Manual  
F.01U.278.517 | V2.0 | 2012.11  
 
       
20 en | Operation  
LE10 Radio Receiver  
6.5.2  
Activation of a programmed transmitter with a  
battery-low message or with a new battery  
The behavior of the device is the same as in  
6.6  
Open receiver (modes 6 and 7)  
6.6.1  
Activation of a transmitter in the reception range  
Device behavior  
The green LED stays permanently on.  
The red LED lights up for 10 seconds.  
Relay 1 switches on for 10 seconds.  
Relay 2 switches on for 2 seconds.  
Activation of any transmitter during these 10 seconds will  
retrigger the procedure.  
NOTICE!  
In these modes 6 and 7, there is no battery-low indication.  
6.7  
Daily messages in modes 1, 2 or 5  
6.7.1  
Daily message with battery-low signal  
Device behavior  
The green LED stays permanently on.  
Upon receiving a daily message with battery-low signal:  
The red LED blinks every 10 seconds.  
Relay 1 stays off.  
Relay 2 switches on, until the battery is changed.  
When the battery is changed, the red LED and Relay 2 switch  
off if a daily message or a transmitter activation is detected.  
NOTICE!  
In Normal mode 2, the red LED is deactivated regarding battery-  
low indication and will not show any indication.  
F.01U.278.517 | V2.0 | 2012.11  
User Manual  
Bosch Security Systems  
 
         
LE10 Radio Receiver  
Operation | en 21  
6.7.2  
Reset of a battery-low indication with button T1  
Device behavior  
The green LED stays permanently on.  
The red LED is already blinking every 10 seconds.  
Upon pressing button T1 min. 1 second, there is a reset of the  
battery-low indication:  
The red LED turns off.  
Relay 2 switches off.  
NOTICE!  
If you disconnect and reconnect the power supply, the battery-  
low indication will be reset as well.  
6.8  
Extended MIYN46 (mode 8, only with SW  
1.10)  
Programming and deleting of transmitters is done as in Mode 1.  
Standby  
The green LED stays permanently on.  
The red LED is off.  
Relay 1 is switched off.  
Relay 2 is switched off.  
When a MIYS37 transmitter, MIYS35 transmitter, MIYRAC  
contact, MIYMD ManDown Sensor are activated:  
The green LED stays permanently on.  
The red LED turns on for 2 seconds.  
Relay 1 is switched on for 2 seconds.  
Relay 2 is switched off.  
When a MIYN46 transmitter’s red or blue button is pressed,  
or when one of its inputs is activated:  
The green LED stays permanently on.  
The red LED and Relay 1 switch on for 6 minutes or until  
the green button of the MIYN46 transmitter is pressed.  
Relay 2 is switched off.  
Bosch Security Systems  
User Manual  
F.01U.278.517 | V2.0 | 2012.11  
 
   
22 en | Operation  
LE10 Radio Receiver  
NOTICE!  
A MIYN46 transmitter in repeated alarm mode extends the  
behavior of the LE10 by approximately 26 minutes. If several  
MIYN46 transmitters are programmed, each activated  
transmitter stops the sequence and starts its own sequence.  
Battery-low indication:  
Relay 2 switches on for 2 seconds.  
The red LED flashes for 2 seconds, then blinks 1 second  
every 10 seconds.  
For all MIYS35 and MIYS37 transmitters, the battery low status  
is triggered when the transmitter is activated or with the daily  
message. For all MIYN46 transmitters, the battery low status is  
triggered only with the daily message.  
6.9  
Dual channel receiver (mode 9, only with  
SW 1.10)  
Programming and deleting of transmitters is done as in Mode 1.  
Standby  
The green LED stays permanently on.  
The red LED is off.  
Relay 1 is switched off.  
Relay 2 is switched off.  
When a transmitter, that is matched on a odd position (1, 3, 5,  
etc.), is activated:  
Relay 1 switches on for 2 seconds.  
The red LED turns on for 2 seconds.  
When a transmitter, that is matched on a even position (2, 4,  
6, etc.), is activated:  
Relay 2 switches on for 2 seconds.  
The red LED blinks 1 second on, 1 second off, 1 second on.  
Battery low indication (until the battery is exchanged)  
The red LED flashes during 2 seconds, then flashes 1  
second every 10 seconds.  
F.01U.278.517 | V2.0 | 2012.11  
User Manual  
Bosch Security Systems  
 
 
LE10 Radio Receiver  
Technical data | en 23  
7
Technical data  
Dimensions  
5.3 x 3.2 x 1.0 inches  
(133 x 82 x 26 mm)  
3.9 oz (110 g)  
ABS  
Weight  
Material  
Color  
Top: white, similar to RAL 9010  
Bottom: charcoal  
External power supply  
Current consumption  
Outputs  
8-30 VDC  
< 25 mA  
2 relays, with max 28 V DC or  
AC, 250 mA maximum  
Indication  
2 LEDs, one green, one red  
434.01 MHz  
Frequency  
Protection class  
IP21  
Operating temperature range 32°F - 113°F (0°C - 45 °C)  
Bosch Security Systems  
User Manual  
F.01U.278.517 | V2.0 | 2012.11  
 
 
Bosch Security Systems  
2400 Geng Road, Suite 200  
Palo Alto, CA 94303  
U.S.A.  
© Bosch Security Systems, 2012  
 

Bolens Tiller 12067 User Manual
Bosch Power Tools Cordless Sander PS50 User Manual
Brinkmann Gas Grill Series 4615 User Manual
Broan Range 413002 User Manual
Cadet Patio Heater CEH 003M User Manual
Cambridge Audio Stereo Amplifier 340A User Manual
Campbell Hausfeld Power Roller AL2270 User Manual
Cannon Scanner DR 2580C User Manual
Canon Film Camera 312 XL S User Manual
Chamberlain Automobile Electronics 942FP User Manual