Bose Stereo System AM325319 User Manual
SOUNDDOCK® SERIES II  
DIGITAL MUSIC SYSTEM  
Owner’s Guide | Guía de usuario | Notice d’utilisation  
 
English  
TAB 2  
TAB 3  
TAB 4  
TAB 5  
TAB 6  
TAB 7  
TAB 8  
IMPORTANT SAFETY INSTRUCTIONS  
1. Read these instructions – for all components before using this product.  
2. Keep these instructions – for future reference.  
3. Heed all warnings – on the product and in the owner’s guide.  
4. Follow all instructions.  
13. Refer all servicing to qualified service personnel. Servicing is required  
when the apparatus has been damaged in any way: such as power  
supply cord or plug is damaged; liquid has been spilled or objects have  
fallen into the apparatus; the apparatus has been exposed to rain or  
moisture, does not operate normally, or has been dropped – Do not  
attempt to service this product yourself. Opening or removing covers may  
expose you to dangerous voltages or other hazards. Please call Bose to be  
referred to an authorized service center near you.  
5. Do not use this apparatus near water or moisture – Do not use this  
product near a bathtub, washbowl, kitchen sink, laundry tub, in a wet  
basement, near a swimming pool, or anywhere else that water or moisture  
are present.  
14. To prevent risk of fire or electric shock, avoid overloading wall outlets,  
extension cords, or integral convenience receptacles.  
6. Clean only with a dry cloth – and as directed by Bose Corporation.  
15. Do not let objects or liquids enter the product – as they may touch  
dangerous voltage points or short-out parts that could result in a fire or  
electric shock.  
Unplug this product from the wall outlet before cleaning.  
7. Do not block any ventilation openings. Install in accordance with the  
manufacturer’s instructions – To ensure reliable operation of the product  
and to protect it from overheating, put the product in a position and loca-  
tion that will not interfere with its proper ventilation. For example, do not  
place the product on a bed, sofa, or similar surface that may block the  
ventilation openings. Do not put it in a built-in system, such as a bookcase  
or a cabinet that may keep air from flowing through its ventilation openings.  
16. See product enclosure for safety related markings.  
17. Use proper power sources – Plug the product into a proper power source,  
as described in the operating instructions or as marked on the product.  
Information about products that generate  
electrical noise  
8. Do not install near any heat sources, such as radiators, heat registers,  
stoves or other apparatus (including amplifiers) that produce heat.  
If applicable, this equipment has been tested and found to comply with  
the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.  
These limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses, and  
can radiate radio frequency energy and, if not installed and used in accordance  
with the instructions, may cause harmful interference to radio communications.  
However, this is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off  
and on, you are encouraged to try to correct the interference by one or more  
of the following measures:  
9. Protect the power cord from being walked on or pinched, particularly  
at plugs, convenience receptacles, and the point where they exit from  
the apparatus.  
10. Only use attachments/accessories specified by the manufacturer.  
11. Use only with the cart, stand, tripod, bracket or table  
specified by the manufacturer or sold with the apparatus.  
When a cart is used, use caution when moving the cart/  
apparatus combination to avoid injury from tip-over.  
12. Unplug this apparatus during lightning storms or when  
unused for long periods of time – to prevent damage to  
this product.  
• Reorient or relocate the antenna in the device receiving the interference.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment to an outlet on a different circuit than the one to  
which the receiver is connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
This product complies with the Canadian RSS-310 Class B specification.  
iii  
 
TAB 8  
TAB 7  
TAB 6  
TAB 5  
TAB 4  
TAB 3  
TAB 2  
English  
SOUNDDOCK® SERIES II DIGITAL MUSIC SYSTEM  
1. Place the system on a firm and level surface.  
Thank you for your purchase  
Congratulations on your choice of the SoundDock® Series II  
2. Plug the power pack into the DC POWER connector on  
the rear of the system.  
digital music system from Bose.  
3. Plug the small end of the power cord into the connector  
Designed specifically to work with your iPod or iPhone,  
this system provides high-quality audio performance that  
invites your music to come out and play. Whether the music  
is from your iPod/iPhone or from another connected device,  
you’ll find that it attracts a wide audience of people who love  
the sound.  
on the power pack.  
4. Plug the other end of this cord into a wall outlet. You will  
hear a short tone indicating a power connection has been  
made.  
Unpacking and setting up  
Check the carton for all of the parts shown. Save the carton  
for possible future use. It provides the best means to repack  
the system for transporting it outside your residence.  
❏ Remote control  
DC POWER  
Power  
cord  
Power  
pack  
❏ Power pack  
❏ SoundDock Series II  
digital music system  
❏ Power cord  
2
 
English  
TAB 2  
TAB 3  
TAB 4  
TAB 5  
TAB 6  
TAB 7  
TAB 8  
SOUNDDOCK® SERIES II DIGITAL MUSIC SYSTEM  
To replace the universal adapter:  
Using your iPod/iPhone  
1. Insert a fingernail into the adapter slot and pull up to  
remove the adapter from the well of the dock. Or use an  
object that fits into the slot to gently pry out the adapter.  
You can use the system right away, with the universal dock  
adapter already installed. Or you can replace the installed  
adapter with the insert supplied with your iPod/iPhone.  
With either the adapter or your insert in place:  
1. Set your iPod/iPhone to play, then firmly insert it into the  
dock.  
The system begins to play immediately.  
2. Place your insert into the well and press on the edges until  
they are flush with the dock.  
+ and – volume buttons  
2. Adjust the volume using buttons on the system dock or  
the remote control volume buttons.  
Note: Whenever you press either button, a small light on the  
front of the system flashes briefly.  
3
 
TAB 8  
TAB 7  
TAB 6  
TAB 5  
TAB 4  
TAB 3  
TAB 2  
English  
SOUNDDOCK® SERIES II DIGITAL MUSIC SYSTEM  
Using the remote  
Using another audio device  
Touch any button (except Off) to turn on the SoundDock  
system.  
You can play another audio by connecting it to the system.  
This requires a cable with a 3.5mm mini plug at one end.  
Off  
Play/Pause  
• Halts and resumes  
play.  
• Press and hold to  
play another  
connected device  
while your iPod/  
iPhone charges.  
1. Set the audio device to slightly below full volume, then  
• Turns off both your  
iPod/IPhone and  
the system.  
plug it into the AUDIO INPUT connector.  
Volume  
• Press and hold to  
change the volume  
quickly.  
Playlist select  
• Moves to the next  
or previous playlist.  
Skip/scan back  
Skip/scan forward  
• Press once to skip  
to the beginning of  
the current track.  
• Press twice to skip  
to the beginning of  
the previous track.  
• Press and hold to  
scan backward  
• Press once to skip to  
the next track.  
• Press and hold  
to scan forward  
quickly.  
2. If your iPod/iPhone is in the system dock and charging,  
press and hold the Play/Pause button for three seconds to  
hear the other device.  
3. Adjust the volume using buttons on the system dock or  
quickly.  
the remote control volume buttons.  
Other buttons on the remote do not control this other  
device. To return to listening to your iPod/iPhone, press  
the Play/Pause button once.  
Note: Each time you press a button on the remote control, a  
small light on the front of the system flashes briefly.  
4
 
 
English  
TAB 2  
TAB 3  
TAB 4  
TAB 5  
TAB 6  
TAB 7  
TAB 8  
SOUNDDOCK® SERIES II DIGITAL MUSIC SYSTEM  
Maintaining the system  
WARNINGS:  
• Keep the remote control battery away from children. It may  
cause a fire or chemical burn if mishandled. Do not recharge,  
disassemble, heat above 140°F (60°C), or incinerate.  
Changing the remote control battery is the only regular  
maintenance that is required. You may also clean the system.  
• Dispose of used batteries promptly. Replace only with a  
battery of the correct type and model number.  
• Danger of explosion if battery is incorrectly replaced.  
Replace only with Duracell, Eveready, Energizer, Maxell,  
Toshiba, Sanyo, CR2032 or DL2032 3-volt lithium.  
Replacing the remote battery  
When the remote stops operating or its range seems  
reduced, it is time to change the remote battery.  
1. Using a coin, turn the battery cover  
slightly counterclockwise.  
2. Remove the cover and insert the  
new battery (CR2032 or DL2032)  
flat side up, with the + symbol in  
view.  
Cleaning the system  
Wipe the system using a soft, dry cloth. You can also lightly  
vacuum the grille.  
• Do not use solvents, chemicals, or sprays.  
3. Reseat the cover and turn it  
• Do not allow liquids to spill or objects to drop into any  
openings.  
clockwise to lock into place.  
5
 
TAB 8  
TAB 7  
TAB 6  
TAB 5  
TAB 4  
TAB 3  
TAB 2  
English  
SOUNDDOCK® SERIES II DIGITAL MUSIC SYSTEM  
Troubleshooting  
Problem  
What to do  
Your iPod/iPhone does not  
dock properly  
• Remove your iPod/iPhone from the dock and check for obstructions on the connectors in the dock and on  
your iPod/iPhone. Then reseat it in the dock.  
• Remove your iPod/iPhone from the dock, wait five seconds, then firmly reseat it. You may need to do this a  
few times.  
No sound  
• Increase the volume setting for the system.  
• Increase the volume on the iPod/iPhone or your second audio device, if it is playing.  
• Make sure the system is plugged in, your iPod/iPhone or other audio device is turned on, and audio is  
playing.  
• Press the Play/stop button on the remote control. Press and hold this button to hear a second device while  
the iPod/iPhone is charging.  
• Unplug the power cord for one minute, then plug it back in. This resets the system (you should hear a tone  
when the system is powered back on).  
• Make sure you have the latest version of software on your iPod/iPhone.  
• Make sure there are no empty playlists on your iPod/iPhone.  
Your iPod/iPhone does not  
navigate playlists using  
the remote  
6
 
English  
TAB 2  
TAB 3  
TAB 4  
TAB 5  
TAB 6  
TAB 7  
TAB 8  
SOUNDDOCK® SERIES II DIGITAL MUSIC SYSTEM  
Problem  
What to do  
Your iPod/iPhone does not  
respond to the SoundDock®  
remote control buttons  
shown:  
• Remove your iPod/iPhone from the dock, wait five seconds, then firmly reseat the iPod/iPhone.  
• Try the remote from a different location. If it works there, check for interference from bright room lights or  
sunlight. Wipe off the small lens on the front end of the remote with a clean, dry cloth.  
• Make sure there is a clear pathway between the remote lens and your SoundDocksystem.  
• Remove and reinsert the battery as shown on page 5.  
• Replace the remote control battery as shown on page 5.  
Your SoundDockdoes not  
respond to any controls  
• Unplug the power cord for one minute, then plug it back in. This resets the system (you should hear a tone  
when the system is powered back on).  
• Contact your local Bose® dealer about the problem.  
Your iPod/iPhone does not  
charge  
• Remove your iPod/iPhone from the dock and check for any connection obstructions. Reseat the iPod/  
iPhone firmly.  
• Make sure your iPod is a compatible model (one that does not have four buttons above the click  
wheel).  
7
 
TAB 8  
TAB 7  
TAB 6  
TAB 5  
TAB 4  
TAB 3  
TAB 2  
English  
SOUNDDOCK® SERIES II DIGITAL MUSIC SYSTEM  
Warranty  
Customer Service  
®
Your Bose SoundDock Series II digital music system is  
covered by a limited transferable warranty. Details of the  
limited warranty are provided on the product registration  
card that is included in the carton. Please refer to the card for  
instructions on how to register. Failure to do so will not affect  
your limited warranty rights.  
For questions about the SoundDocksystem, contact your  
local Bose® dealer. To contact Bose directly, see the address  
list included in the carton.  
Technical Information  
What you must do to obtain Limited Warranty Service:  
Power rating  
1. Return product, with proof of purchase from an authorized  
100-240V  
50-60Hz, 1.5A, 81-100VA  
Bose dealer, using the following procedures:  
System size and weight  
6.65"H x 11.91"W x 6.48"D (16.89 cm x 30.26 cm x 16.47 cm)  
2. Contact the Bose organization in your country/region  
(visit Global.Bose.com/register for Bose contact  
information in your country/region) for specific return  
and shipping instructions;  
4.56 lb (2.1 kg)  
Compatibility  
The SoundDock digital music system is compatible with all  
iPhones and most iPod models.  
3. Label and ship the product, freight prepaid, to the address  
provided by the Bose organization in your country;  
and place any necessary return authorization number  
prominently on the outside of the carton. Cartons not  
bearing a return authorization number, where required,  
will be refused.  
Not compatible with 3rd generation with dock connector  
(iPod has four buttons above the touch wheel).  
8
 
English  
TAB 2  
TAB 3  
TAB 4  
TAB 5  
TAB 6  
TAB 7  
TAB 8  
SOUNDDOCK® SERIES II DIGITAL MUSIC SYSTEM  
SoundDock and the SoundDock system design are registered trademarks of  
Bose Corporation in the U.S. and other countries.  
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.  
iPhone is a trademark of Apple Inc. All other marks are property of Bose  
Corporation.  
“Made for iPod” means that an electronic accessory has been designed to  
connect specifically to iPod and has been certified by the developer to meet  
Apple performance standards.  
“Works with iPhone” means that an electronic accessory has been designed to  
connect specifically to iPhone and has been certified by the developer to meet  
Apple performance standards.  
Apple is not responsible for the operation of this device or its compliance with  
safety and regulatory standards.  
9
 
©2009 Bose Corporation, The Mountain,  
Framingham, MA 01701-9168 USA  
AM325319 Rev.00  
 

Belkin Universal Remote F4F315 T User Manual
Billy Goat Blower SV50HR User Manual
Black Decker Coffeemaker TCMKT850C User Manual
Black Decker Sander 90527869 User Manual
Bosch Appliances Network Router ATM POS Bridge User Manual
Braun Electric Shaver 360S 3 User Manual
Brother Photo Printer DCP 135C User Manual
Bushnell Boating Equipment 70 0001 User Manual
Chicago Electric Work Light 94761 User Manual
Chromalox Air Conditioner PF490 5 User Manual