2-Port USB SuperBooster
Receiver Wall Plate
Part #29345
User Manual
Features
•
•
Extends the distance of a USB device from a USB-enabled computer up to 150ft
One part of a total solution- transmitter is purchased separately giving you the
flexibility to customize the configuration to your specific needs
Transmitter options include a wall plate (part #29344) or a dongle (part #29348)
Ideal for use with USB projectors, interactive whiteboards, cameras, printers,
web cams, hubs, and other USB devices
•
•
•
•
•
•
Fits a standard J-box
Compatible with Leviton Decora® brand cover plates
Bus-powered so no external power source is required
Uses standard Cat5/Cat5E/Cat6 patch cord (not included) for ease of use and
flexibility
•
•
•
Included tool-less IDC RJ45 connector allows you to terminate your own cable
Compliant with USB Specification 1.1
Connectors:
o Transmitter (sold separately): USB Type B Female; RJ45 Female
o Receiver: Two USB Type A Female Ports; RJ45 Female
*Decora™ is a registered trademark of Leviton Manufacturing Company, Inc. This Product is not manufactured or endorsed by the
Leviton Manufacturing Company, Inc.
Package Contents
• USB SuperBooster Wall Plate- Receiver Unit
• (1) One RJ45 tool-less IDC connector
• (2) Two #6x32 slotted/phillips screws
• User Guide
2
Installing your USB SuperBooster Wall Plate
The USB SuperBooster solution has a transmitter unit (sold separately) and a receiver
unit. Make certain you install the transmitter unit at your computer or
source side. The receiver unit needs to be installed on the device side.
1) Install the Wall Plate Transmitter in a standard J-box where you want your
source/computer or connect the Dongle Transmitter to your computer
2) Install the Receiver Wall Plate unit in a standard J-box where you want your USB
device
3) Use a pre-terminated Cat5/Cat5E/Cat6 cable (recommended) or terminate your
own cable using the tool-less RJ45 connectors included to connect the transmitter
and receiver together (see below for instructions on terminating your own cable)
4) If using a Wall Plate Transmitter, plug your computer into the transmitter end
(USB B side) using a standard A/B USB cable (The green LED will light to
indicate you have a good connection to the wall plate) or skip this step if using a
Dongle Transmitter as you connected your computer in step 1
5) Plug your device into the receiver end (USB A side) using a standard A/B (or
A/Mini-B) USB cable (The green LED will light to indicate you have a good
connection to the wall plate)
6) Turn your computer/source on and begin using your device
Terminating a Cat5/Cat5E/Cat6 Cable Using the Tool-less IDC
1) Open the plug by lifting the clear
plastic end
2) Pin 1 of the connector is on the
left side of the clear plastic shell
while Pin 8 is on the right side of
the connector (with RJ45
connector facing away from you)
3) Thread the white/orange
conductor on your Cat5/5E/6
cable into Pin 1
9) Thread the white/brown
conductor on your Cat5/5E/6
cable into Pin 7
10) Thread the brown conductor on
your Cat5/5E/6 cable into Pin 8
11) Repeat steps 1-10 to terminate
the other end of your Cat5/5E/6
cable
4) Thread the orange conductor on
your Cat5/5E/6 cable into Pin 2
5) Thread the white/green
conductor on your Cat5/5E/6
cable into Pin 3
Pin 1
6) Thread the blue conductor on
your Cat5/5E/6 cable into Pin 4
7) Thread the white/blue conductor
on your Cat5/5E/6 cable into Pin
5
Pin 8
8) Thread the green conductor on
your Cat5/5E/6 cable into Pin 6
3
Termination Chart
Pin Number Network (Cat5/5E/6)
Conductor Color
1
2
3
4
5
6
7
8
white/orange
orange
White/green
Blue
White/blue
Green
White/brown
brown
Application Diagram
Transmitter
Receiver
3555 Kettering Blvd.
Moraine, Ohio 45439
1-800-293-4970
1
|