Cambo Automobile Accessories LCMR5RP User Manual

Rearview Mirror with 4.5" Color LCD with  
Navigation and 2 Camera inputs  
Model: LCMR5RP  
Installation Manual  
Features:  
Rearview Mirror with 4.5" LCD  
Rearview Camera Input  
Interior Camera Input  
Navigation Input  
NTSC /PAL Camera Compatible  
 
TABLE OF CONTENTS  
Cautions!  
Preface  
1
3
WARNING  
Packing list  
3
3
1.Installation Instructions  
2.Signal Inputs  
4
5
3.Controls and Indicators  
7
Specifications  
9
Maintenance  
10  
11  
12  
Troubleshooting  
Illustration of connections  
2
 
Preface  
This replacement mirror /monitor can display up to 3 different video  
inputs. The inputs are Navigation, Rear observation camera and Interior  
observation camera.  
Not all rearview mirrors attach to the vehicle with the same style mount.  
Please consult the application guide for the appropriate mounting bracket  
for your vehicle or call Tech Service at 800-225-6074.  
There is a blind spot that exists at the back of a vehicle while the vehicle is  
in reverse. Equipped with a camera, this electronic rearview mirror  
ensures safety by providing the driver with a clear and wide image of the  
area behind the vehicle while it is in reverse.  
WARNING:  
Backing up vehicle  
Do not back up the vehicle while watching the mirror/monitor screen.  
Always look in the direction of vehicle motion. Use the mirror/monitor as  
an aid in safety confirmation. The distance looks different in the monitor.  
Packing list  
The Rear view mirror Model LCMR5RP consists of the following items:  
1. Rear View Mirror-1  
2. Camera Cable-2  
3. Control Box-1  
4. Control Box Monitor Cable -1  
3
 
1. Installation Instructions  
(1) Mount the mirror/monitor  
a)  
b)  
Remove the original factory mirror. (Do not use excessive force when  
removing factory mirror.) Check to make sure that the factory mirror mount you  
remove matches the mirror mount on the replacement mirror. If it does not  
match, consult the application guide or call Technical Service at 800-225-6074.  
Slide the receiving bracket on the back of the new mirror stalk onto the  
windshield mounting button. Move the bracket back and forth until completely  
seated.  
c) Tightly the T-20 mounting bracket screw.  
(2) Navigation monitor connection: Insert the connector from the navigation  
monitor cable into the receptacle at the backside of the mirror/monitor. Route the rest  
of the monitor cable under the headliner, down the A pillar to the Navigation  
computer.  
(3) Control box connection: Connect the 8-pin extension cable to the rearview  
mirror/monitor 8 pin cable. Route the cable under the headliner of the windshield then  
down the A pillar behind the plastic shroud to the under dash area. Connect the 8-pin  
cable to the control box 8 pin connector.  
4
 
(4) Electrical Connections: Connect the 4 wires in the following manner.  
a) Red wire - 12 volt constant (positive)  
b) Black wire - Chassis ground (negative)  
c) Blue wire - 12-volt ignition (12 volt with ignition on)  
d) Green wire - Reverse light switch (12 volt when vehicle is in the reverse gear)  
WARNING: Observe polarity when connecting the wires.  
Figure 2  
2. Signal Inputs  
The signal input connections for the system include:  
(1)  
Rear Camera: Plug the RJ 11 camera cable end into the control box  
AVin-1 location, route the cable to the rear camera and plug the 4-pin connector  
into camera 4 pin connector. Users can see the rearview camera image when the car  
is shifted into reverse.  
(2) Interior Camera: Plug the RJ 11 camera cable end into the control box AVin-2,  
Users can see the interior camera image when the “CAM” button is pressed.  
(3)  
Navigation: The navigation signal is supplied via the monitor cable  
plugged directly into the rear of the mirror.  
(4) Navigation Image (optional Navigation System required)  
The Navigation Image is the default mode, and will only be overridden  
when the vehicle gear selector is moved into reverse, or if the CAM button  
on the mirror is pressed.  
5
 
Some operators may find that leaving the Navigation Image on the LCD  
monitor at all times becomes a distraction while operating their motor  
vehicle. For the convenience of those operators, a ‘Display Timer Slide  
Control Switch’ has been added to the mirror.  
A. When the Slide Control Switch is moved to the far right end position,  
the Navigation image will remain on at all times.  
B. When the Slide Control Switch is moved to the far left end position,  
the Navigation image will remain off at all times.  
C. Positioning the Slide Control Switch anywhere in the center area will  
automatically enable an internal timer. The timer is adjustable between 10  
Seconds (further left) to 3 minutes (further right).  
D. When the Navigation System is in guidance mode, every time a turn-  
by-turn voice guidance command is received, the Navigation image will  
automatically turn on and remain on for the pre-selected time set by the  
Slide Switch. After the pre-set time has expired, the Navigation display will  
turn off and remain off until the next voice command is received.  
HINT 1: When entering a new address into the Navigation Address Book, it  
will be easier to move the Slide Control Switch all the way to the right to  
keep the LCD display on until the address has been completed.  
HINT 2: When in Timed Display Mode, you can press the “+” or “-“ button on  
the mirror to turn the Navigation image on for the full extent of the pre-set  
time.  
6
 
Figure 5  
3. Controls and Indicators  
Figure 5 shows the function controls of the rear view mirror.  
A: 4.5" LCD Panel  
B: Rearview Mirror Glass  
C: “+”Button (optional Navigation System required)  
Incrementally increase volume level of the navigation voice command when pressed.  
Note: Will only operate when the Navigation System remote control is removed from the  
cradle.  
D: “CAM”Button  
- If you have installed an optional interior view camera, pressing the CAM button will  
display the image from the interior view camera on the LCD panel. - If you do not have an  
interior view camera installed, but have installed a back up camera, then pressing the CAM  
button will display the image from the back up camera on the LCD panel.  
- Either image will be displayed for as long as the CAM button is held on. As soon as the  
button is released, the LCD will automatically switch back to the original setting.  
E: “MAP”Button (optional Navigation System required)  
Each time the “MAP” button is pressed, the navigation display will toggle between Map,  
Icon only and split screen while in navigation mode.  
7
 
Note: Will only operate when the Navigation System remote control is removed from the  
cradle.  
F: “-” Button (optional Navigation System required)  
Incrementally decrease volume level of the navigation voice command when pressed.  
Note: Will only operate when the Navigation System remote control is removed from the  
cradle.  
G: Internal Speaker  
H: LCD Brightness Control  
I: Internal Infra-RED Receiver for use with Navigation System Remote Control.  
J: Power LED (Red when Power is on)  
K: Display Timer Slide Control Switch : (optional Navigation System required)  
Refer to page 5 Signal Inputs #4 for detailed operation notes.  
M: Internal Speaker Switch: Used to turn mirror speaker on/off. Move this switch to the  
Off position when using the external speaker interface included with the optional  
Navigation System.  
8
 
Specifications  
General  
Power Supply  
12VDC  
<12W  
Power Consumption  
Current Draw  
<800mA  
Video Input  
1Vp-p/ 75 Impedance  
Audio Input  
<=1V  
Audio Power Output  
Operating Temperature Range  
0.5W × 1 (16)  
0to 50℃  
Display System  
Screen  
4.5” TFT Color LCD  
400 cd/㎡  
Brightness  
Contrast Ratio  
Backlight Life  
Resolution  
150 : 1  
10000 hours  
960×234  
Video Format  
Display Format  
Navigation input  
PAL/NTSC auto detect  
16 : 9  
RGB  
9
 
Maintenance  
Though your Rearview mirror requires little care, you can still maintain its  
condition and performance by following the procedures below.  
Keep your system away from excessive moisture, extreme heat or cold,  
and magnetic fields.  
Keep liquids away from the display and mirror.  
To avoid damage, do not place external devices or other objects on the  
top of the mirror.  
Occasionally wipe the rearview mirror set with a soft, damp cloth.  
Occasionally clean the surface of the mirror with a soft cloth moistened  
with water or window cleaner.  
10  
 
Troubleshooting  
Symptoms  
Solutions  
1. Check the installation-wiring diagram.  
2. Ensure that the parallel red and black line from  
the control box is connected properly.  
3. Check for 12 volts on the blue wire while the  
ignition on.  
The ON/OFF signal light <E> is  
not on after the car is started?  
1. Check the rearview Camera lens.  
2. Check the rearview Camera wiring and  
connection.  
3. Check the cable from the rearview mirror is  
connected to the control box.  
No video signal appears while  
reversing the car?  
4. Check out the wire connection (to find out  
whether the system’s reverse wire cable is  
connected to the reverse switch gear of the car)  
Video image is not sharp enough?  
Clean the lens of the camera.  
 
Illustration of Connections  
Figure 6  
12  
 
© 2005 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788  
128-7381  
 

Beko Washer WI 1382 User Manual
Blackberry Cell Phone Smartphones User Manual
Bosch Appliances Boiler 24i junior User Manual
Bosch Appliances Home Security System NDN 921 User Manual
Boss Audio Systems Stereo System GT1000M User Manual
Brother All in One Printer MFC4420C User Manual
Canon Photo Scanner MG3520 User Manual
Canon Scanner FAX L240 User Manual
Casio Printer KL 100E User Manual
Casio Watch MA0506 EA User Manual