© 2012 CASIO COMPUTER CO., LTD.
MA1205-EA
Operation Guide DQ-950S
ILLUSTRATION
1
2
3
SNOOZE/LIGHT
RESET
MAX/MIN
MAX/MIN
4
SET
DEMO
8
SNOOZE/LIGHT
ALARM
SNOOZE
ON
ALARM
OFF
5
6
7
SNOOZE
ON
SET
DEMO
OFF
RESET
RESET
• A sticker is affixed to the glass of the clock when you purchase it. Be sure to remove the sticker before using the
clock.
• Depending on the clock model, the configuration of your clock may differ somewhat from that shown in the
illustration.
Alarm Off
Snooze Alarm On
PM
indicator
Alarm on
indicator
Current time
(Hour, minutes,
seconds)
Snooze on
indicator
Day of the week
DATE
(month - date)
Alarm time
Current Temperature
Current Humidity
1
Operation Guide DQ-950S
USING THE ALARM
THERMOMETER AND HYGROMETER FUNCTIONS
The alarm sounds when the alarm time you set is reached. You can also use the Alarm Mode selector (8) to
select the snooze alarm feature.
A built-in sensor measures temperature and humidity, and shows the measured value on the display.
The readout from the temperature sensor can also be switched between Celsius (°C) and Fahrenheit (°F).
Setting the Alarm Time
Temperature Measurements
• The temperature display shows “LO” for temperatures below –19.9°C (–3.8°F) and “HI” for temperatures above
49.9°C (121.8°F).
• Though temperature readings are displayed up to 0°C (32°F) and greater than 41°C (105°F), note that such
readings are actually outside the guaranteed temperature range of this clock.
Use the – (DOWN) and + (UP) buttons (4) to set the alarm time.
Pressing the – (DOWN) and + (UP) buttons (4) causes the alarm time to appear in place of the date on the
display.
Switching between Celsius and Fahrenheit
MAX/MIN
• Push the °C/°F button (3) to select either Celsius (°C) or Fahrenheit (°F).
• Switching between Celsius and Fahrenheit causes current high temperature/humidity and low temperature/
humidity memory contents to be cleared.
Press to change the alarm
time setting ( ).
Press to change the alarm
time setting (+).
—
Celsius (°C)
Fahrenheit (°F)
• Holding down + (UP) or – (DOWN) changes the digits at high speed.
°C/°F button (3)
Turning the Alarm On and Off
Use the Alarm Mode selector (8) on the side of the clock to turn the alarm on and off, and to select the snooze
°C
°F
feature.
Humidity Measurements
Alarm Mode selector
SNOOZE
Description
• The humidity display shows “LO” for humidity below 10% and “HI” for humidity above 90%.
The alarm sounds at the preset time for one minute, and seven more times every five
minutes thereafter. Even if you stop the alarm by pressing the SNOOZE/LIGHT
button (1), the alarm sounds again about five minutes later.
• Whenever the current temperature is outside the range of 0°C to 49.9°C, the humidity display will show “– –”.
Daily High Temperature/Humidity, Low Temperature/Humidity Memory
• The indicator
activated.
flashes on the display to indicate that the snooze feature is
• The clock remembers the highest and lowest temperature and humidity readings for the current 24-hour day.
Each press of the MAX/MIN button (2) cycles between screens as illustrated below.
• Daily high and low temperature/humidity memory contents are cleared each day at midnight.
ON
The alarm sounds at the preset time for one minute.
The alarm does not sound.
Changing the Temperature/Humidity Display Screen
• Press of the MAX/MIN button (2). Each press cycles between screens as shown below.
OFF
Current temperature and humidity
• The alarm time appears in place of the date on the display whenever the Alarm Mode selector (8) is set to ON
or SNOOZE.
• The volume of the alarm sound cycles through five levels as it sounds.
MAX/MIN button (2)
MAX/MIN button (2)
Stopping the Alarm
• When alarm is sounding, press the SNOOZE/LIGHT button (1) to stop it. When the snooze feature is turned on,
the alarm will sound again in about five minutes.
• To turn off the snooze feature, slide the Alarm Mode selector (8) to OFF.
High temperature and humidity
Low temperature and humidity
MAX/MIN button (2)
USING THE LIGHT
Pressing the SNOOZE/LIGHT button (1) turns on the light and illuminates the display for easy reading in the dark.
Turning On Temperature/Humidity Screen Auto Cycling
• Hold down the MAX/MIN button (2) for about one second. This will turn on temperature/humidity screen auto
cycling, which causes the screen contents to cycle from one screen to the next at regular intervals.
Important!
• Overuse of the light can shorten battery life.
Current temperature and humidity
High temperature and humidity
Low temperature and humidity
• To turn off temperature/humidity screen auto cycling, press the MAX/MIN button (2).
3
Operation Guide DQ-950S
BATTERY REPLACEMENT
Replace batteries whenever the display of the clock becomes dim and difficult to read.
1. Open the battery compartment cover as shown in the illustration.
2. Remove all of the old batteries.
3. Load a full set of new batteries. Make sure that their positive (+) and negative (–) ends face in the correct
directions. If you load batteries incorrectly, they can burst and damage the clock.
4. Press the RESET button (7). Be sure to press the RESET button (7) after replacing batteries.
5. Replace the battery compartment cover.
Battery precautions
• Keep batteries out of the reach of small children. If a battery is accidentally swallowed, contact your physician
immediately.
• Be sure to load the batteries with their positive (+) and negative (–) ends facing correctly.
• Never mix old and new batteries, or batteries of different brands.
• Never charge the batteries that come with the clock.
• Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto your
skin.
• Replace the batteries at least once a year, even if the current batteries are working properly.
• The batteries that come with the clock lose some of their power during transport and storage.
SPECIFICATIONS
Accuracy at Normal Temperature: ±60 seconds a month
Calendar System: Auto-calendar pre-programmed from the year 2000 to 2099
Alarm: Daily Alarm, Snooze Alarm (7 repeats)
Thermometer Functions: Measuring range: –19.9°C to 49.9°C (–3.8°F to 121.8°F)
Though temperature readings are displayed up to 0°C (32°F) and greater than 41°C (105°F), note that such
readings are actually outside the guaranteed temperature range of this clock.
High/Low Temperature Memory, Celsius (°C)/Fahrenheit (°F) switching
Temperature Sensor Precision: ±2°C (±4°F) in range of 0°C to 40°C (32°F to 104°F)
Hygrometer Function: Measuring range: 10% to 90%, when temperature is 0°C to 40°C (32°F to 104°F)
High/Low Humidity Memory
Humidity Sensor Precision: ±10%, when temperature is 5°C to 40°C (41°F to 104°F)
Other: LED light; 12/24-hour timekeeping
Battery: Two AAA size batteries (Type: R03)
Battery Life: Approximately 1 year
• 1 minute alarm operation per day
• 5 seconds light operation per day
Operating Temperature: 0°C to 40°C (32°F to 104°F)
4
|