Cavalry Storage Washer Dryer CADA C32A User Manual

User's Manual  
CADA-C32A Series  
 
Thank you for choosing Cavalry.  
We at Cavalry extend our sincere gratitude for your purchase of this product.  
We hope our dedication to delivering high quality products with excellent  
customer service will ensure your continued interest in our products.  
This manual will assist in the operation of the product. To optimize your  
experience with this product, we recommend reading this entire manual  
before usage. Please keep this manual for future reference.  
3
 
Table of Contents  
Preface ....................................................................................................  
List of Accessories .............................................................................  
Product Illustrations ...........................................................................  
Features .............................................................................................  
Setup Instructions ..............................................................................  
RAID ..................................................................................................  
Troubleshooting .................................................................................  
Warranty and Contact ........................................................................  
2
5
6
8
9
13  
16  
19  
4
 
List of Accessories  
1.  
2.  
3.  
4.  
5.  
External power adapter / power cord (look may vary with product)  
FireWire 400 cable  
3
FireWire 800 cable  
USB 2.0 cable  
Resources CD  
4
2
1
5
5
 
Front  
1
1. LED status indicators  
6
 
Back  
2. Power switch  
3
4
5
2
3. Power jack  
4. FireWire 400 port  
5. FireWire 800 port (2)  
6. USB 2.0 port  
7. Ventilation fan  
6
7
7
 
Features  
Plug-and-play for Mac OS X and above  
USB 2.0 and FireWire 400/800 capability  
Pre-formatted in Mac OS X Extended  
Supports RAID  
Exceptional heat dissipating ability  
LED light indicators  
Nearly silent operation  
8
 
Setup Instructions  
Follow the steps below to successfully setup your Cavalry External Hard  
Drive with your computer.  
Step 1. Start your computer and wait for the Mac OS to load completely.  
Step 2. Connect the power adapter to the drive. Then  
plug the power adapter into an electrical outlet.  
NOTE: Make sure the flat end of the plug is facing  
toward the power switch to prevent damage to the pins.  
9
 
Step 3. Connect the square end of the USB cable to the hard drive. Then  
connect the flat end of the USB cable to the USB port on your computer.  
USB Cable Plug  
USB Port  
NOTE: The same procedure applies for FireWire users.  
Step 4. Turn the power switch on.  
NOTE: Connect the USB cable to the drive before connecting the cable to  
the computer. To disconnect, remove the cable from the computer first.  
10  
 
Step 5. Installing drivers for the Cavalry External Hard Drive.  
Mac OS X  
Plug-and-play. No device drivers or configuration required. The  
computer will automatically detect the USB External Hard Drive as a  
new USB device and will be ready to use.  
Windows 2000/XP/Vista  
No drivers required. But reformatting the hard disk is a requirement.  
1. Right-click on My Computer and select "Manage".  
2. In the left column go under "Storage" and select "Disk  
Management".  
3. Right-click on the new drive on the bottom and select "Format".  
4. Select "NTFS" under "File System". Click OK.  
Formatting may take a few minutes to complete.  
11  
 
Windows 98SE/Me  
1. Make sure Windows 98SE/Me is fully updated  
and click on "Windows 98 Driver". Extract the file.  
3. Navigate the device manager.  
4. Right-click on the yellow question mark indicating an unknown  
external storage device.  
5. When the device driver wizard starts, click on the "Browse" button  
to select the search directory to find drivers.  
6. Find the USB 2.0-98 driver in the extracted file.  
7. Click "Next" to continue.  
Step 6. Your external hard drive is now ready to use.  
12  
 
RAID  
Your product has been preconfigured as RAID 1 (mirrored). "Mirrored"  
means that each of the two disks in your disk array contains the same data,  
providing protection against one drive failing; however, when the drive  
appears on your computer, it will be recognized as a single hard drive.  
NOTE: Although the box indicates two hard drives are included, the total  
capacity in RAID 1 mode will not equal the sum of the two because the  
second drive is used as a "backup" of the first drive. (e.g. two 250GB drives  
do not have a 500GB capacity. Instead, only 250GB is available for storage,  
while the other 250GB is a backup of that data.)  
Please contact us at [email protected] if you would like  
to reconfigure the RAID settings on your drive.  
13  
 
Troubleshooting  
LED light indicator does not turn on  
Make sure the power adapter is securely connected to a working electrical  
outlet. Secondly, make sure the USB / FireWire cable is inserted correctly  
into the hard drive and the computer. Turn on the power switch (page 7).  
Computer does not detect hard drive  
Make sure the USB / FireWire cables are securely connected. If this does  
not work, attach another known working device and working cable into the  
USB / FireWire port on the computer. If your computer does not detect your  
known working device, the problem could be your computer's USB / FireWire  
port. If the port and cable both work, and the hard drive is still not detected,  
please contact customer support.  
14  
 
Loud noises coming from external hard drive  
In most cases, loud noises coming from the drive suggest it may either be  
defective or a part is loose. We apologize for any inconvenience this may  
cause. Please contact customer service for assistance.  
"HDD1 ERROR" or "HDD2 ERROR" lights appear  
This indicates one of the drives may need replacing. If the drive is set up with  
RAID1, the hard drive must be replaced by another hard drive of the same  
capacity, brand, and model number. Open the enclosure, remove the failed  
hard drive and replace with the new drive. After inserting the new drive and  
closing the unit, turn it on and the new hard drive will automatically be rebuilt  
using a copy of the data from the good hard drive. The unit does not need to  
be connected to the computer in order to be rebuilt. Do not turn off the power  
during the rebuilding process.  
15  
 
Hard drive will not work with my PC  
This hard drive is formatted for Macs. Format the hard drive according to the  
instructions provided in the Setup Instruction section. Alternatively, see the  
"Formatting Instructions.pdf" located in the "Contents" folder of the  
Resources CD.  
If you have more questions, please refer to the Frequently Asked  
further inquiries, you may contact Bason/Cavalry tech support at  
16  
 
Warranty  
This product comes with a one year warranty from the date of purchase.  
activate the warranty. Please have your Serial Number and Model Number  
ready. We are not responsible for any loss of data. Please back up your data  
often to avoid unexpected losses.  
Contact  
Cavalry Storage, Inc.  
555 E. Easy St.  
Simi Valley, CA 93065  
17  
 
CA1043  
061008  
 

Beko Washer WMB71642S User Manual
Belkin Mouse F8E874 User Manual
Billy Goat Chipper KD510 User Manual
Bose Home Theater System AM314482 User Manual
Breville Cooktop BSG520XL Brushed Silver User Manual
Brinkmann Gas Grill Two Burner User Manual
Calphalon Slow Cooker 1779208 User Manual
Casio Watch 2299 User Manual
Casio Watch AWG101 1A User Manual
CDA Washer CI240 User Manual