Operators Manual
JACK STANDS
Model 950182 - 2-1/4 Ton Capacity per pair
• Safety
• Assembly
• Operation
BEFORE using this product, read this manual
and follow all its Safety and Operating
!
instructions. Failure to do so may result in
personal injury and/or property damage.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Printed in China
SAFETY INSTRUCTIONS
!
!
WARNING
ADVERTENCIA
• Study, understand, and follow all printed
materials provided with and on this
device before use.
• Leer, comprender, y seguir las
instrucciónes antes de utilizar el aparato.
• El manual de instrucciónes y la
información de seguridad deben estar
comunicado en lengua del operador
antes del uso.
• Rated capacity is per pair! Do not
exceed rated capacity.
• Use as matched pair to support one end
of a vehicle only. Use only 1 pair per
vehicle.
• No seguir estas indicaciónes puede
causar daños personales o materiales.
• Use only on hard, level surfaces.
• Center load on saddle.
! SAFETY MESSAGE !
Be sure all tools and personnel are clear
before lowering load. No alterations shall
be made to this device. Only attachments
and/or adapters supplied by the
manufacturer shall be used. Lift only on
areas of the vehicle as specified by the
vehicle manufacturer.
• Jack stands are not to be used to
simultaneously support both ends or one
side of a vehicle.
• No alteration shall be made to this
device.
• Failure to heed these markings may
result in personal injury and/or property
damage.
INSPECTION
Inspect the Jack Stands before each use.
Do not use if bent, broken or cracked
components are noted.
ASSEMBLY
CARTON CONTENTS
RATCHET BAR
Inside the carton box, you will find:
1. Two jack stand frames.
2. Two ratchet bars.
PAWL (INSIDE,
NOT SHOWN)
LOCKING
HANDLE
3. Two lock pins.
BASE
FRAME
HOW TO ASSEMBLE JACK STANDS
(refer to Fig. 1)
LOCK PIN
1. Insert the ratchet bar into frame, orient
the racthet side to the pawl side of
frame.
2. Move the ratchet bar to lowest position
by raising the locking handle and guiding
the bar downward.
3. Support the ratchet bar with suitably
sized wooden block. With hammer and
punch or other suitable tool, drive the
lock pin into the hole at the bottom of
the ratchet bar to prevent overextension
and loss of the bar.
FIG. 1
3
OPERATION
4. Always use jack stands as a pair and
BEFORE USE
only on those parts of a vehicle which
can be fully captured between the outer
lugs of each stand’s saddle.
1. Inspect stands before each use. Do not
use if bent, broken or cracked
components are noted. Ensure that all
parts move freely.
Rated capacity of jack stands is per
!
pair, it is NOT the sum of individual
capacities unless specifically noted to
the contrary by the jack stand
manufacturer. Do Not exceed rated
capacity. Ensure that the vehicle
support points are fully captured
between the outer lugs of both jack
stands. Use a matched pair of jack
stands per vehicle to support 1 end
only. Use 1 pair per vehicle only.
Failure to do so may result in sudden
loss of load, which may cause personal
injury and/or property damage.
2. Before using this product, read the
owner’s manual and familiarize yourself
thoroughly with the product and the
hazards associated with its improper
use.
KNOW YOUR JACK STANDS
SADDLE
RATCHET
BAR
LOCKING
HANDLE
5. Slowly and carefully lower the load
completely onto the stands, ensure that
the load is centered and captured as
described in Step 4.
6. Check to ensure that load is secure on
stands before working under vehicle.
JACK STAND
FRAME
FIG. 2
HOW TO USE YOUR JACK STANDS
TO SUPPORT A VEHICLE
1. Raise the vehicle or load with an
automotive jack.
TO REMOVE AND STORE JACK
STANDS
2. Adjust jack stand height by pulling up
on ratchet bar. The weight of the locking
handle should lock the ratchet bar into
a secure position. To verify this, simply
push down on the locking handle to
ensure that the ratchet bar is secured.
1. Raise vehicle clear of stands with
suitable jack.
2. Raise the locking handle to allow ratchet
bar to glide down to lowest position.
3. Carefully remove stands.
4. Carefully lower vehicle with jack.
5. Ensure that all tools, equipment and
personnel are clear before lowering
load.
3. Carefully position the stands beneath
the load so that when load is lowered it
will contact the center of the jack stand
saddles.
SPECIFICATIONS
CAPACITY
PER PAIR
MODEL
MIN. HEIGHT MAX. HEIGHT BASE DIMENSION NET WEIGHT(2 pcs.)
10-5/8 in.
(270mm)
17-1/8 in.
(435mm)
50182 2-1/4 TON
7-1/2 X 6-3/4 in.
11.4 LBS (APPROX.)
MAINTENANCE
STORAGE
INSPECTION
Store stands in upright position and in a
clean, dry area.
Periodically inspect each stand. Ensure all
parts move freely. Do not apply oil or
grease to any portion of this product. If rust
appears, sand affected area and cover with
suitable utility paint. Please note that there
are no replacement parts applicable to this
device.
For after sale support and assistance:
Call 8:00 AM - 4:45 PM CST., Monday - Friday 1-888-332-6419
4
Get it fixed, at your home or ours!
Your Home
For repair – in your home – of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME®
Call anytime, day or night
(1-800-469-4663)
(U.S.A. and Canada)
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts and Repair Center.
1-800-488-1222 Call anytime, day or night (U.S.A. only)
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6665 (U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparación
a domicilio, y para ordenar piezas:
Au Canada pour service en français:
1-800-LE-FOYERMC
1-888-SU-HOGAR®
(1-888-784-6427)
(1-800-533-6937)
© Sears Brands, LLC
®
Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC
Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC
®
MC Marque de commerce / MD Marque déposée de Sears Brands, LLC
|