The Quick Reference Card provides a quick overview of your spa's main
functions and the operations accessible with your digital control pad.
SC-MP-DY1 / Dual-Pump System
Starting Pump 1:
Turning the light on:
Neptune Series Spas feature an easy-to-change selection of nine
different LED color/display settings. To activate the LED lights,
press the "LIGHT" button on the topside panel one time. To
advance to the next color/display setting, press the "LIGHT" button
twice in a row. The LED's will go off with the first press, then back
on in the next setting with the second press. If the LED's remain off
for more than 5 seconds, the color/display sequence will reset and
start back at the beginning the next time the "LIGHT" button is
pressed. The color/display sequence is:
Press Pump 1 to turn Pump 1 on at low speed.
Press a second time to turn pump to high speed.
Press a third time to turn pump off. When at high
speed, a built-in timer turns pump off after 20 min-
utes and when at low speed after 2 hours, unless
manually deactivated first.
The "Pump 1" indicator lights up
when Pump 1 is on at high speed.
It flashes when Pump 1 is on at low
speed.
Setting #1 LED's light up and slowly cycle throught all six color.
The slow cycle then restarts at the beginning and repeats.
Setting#2 LED's light up and remain on in Aqua.
Setting#3 LED's light up and remain on in Purple.
Setting#4 LED's light up and remain on in Blue.
Starting Pump 2:
Press Pump 2 to turn Pump 2 on. Press a second
time to turn Pump 2 off. A built-in timer automati-
cally turns pump off after 20 minutes, unless pump
has been manually deactivated.
Setting#5 LED's light up and remain on in Gold.
Setting#6 LED's light up and remain on in Green.
Setting#7 LED's light up and remain on in Red.
Setting#8 LED's light up for 2 sec, flash off, then flash on in the
next color, until all six colors have been displayed. The flashing
cycle then restarts at the beginning and repeats.
The "Pump 2" indicator lights up
when Pump 2 is on.
Setting#9 LED's flash on/off quickly, for a strobe light effect.
The LED lights will automatically turn themselves off after 2 hours
in any one setting.
Setting water temperature:
Use Up or Down arrow keys to regulate water
temperature. The temperature setting will be
displayed for 5 seconds to confirm your new
selection.
Automatic water heater start:
When water temperature is 1˚F (0.5˚C) lower
than the Set Point, the heater will automatically
turn on until water temperature reaches Set Point
plus 1˚F (0.5˚C).
The "Set Point" indicator displays the
desired temperature, NOT the current
water temperature!
The "Heater" indicator lights up when
the heater is on. It flashes when there
is a request for more heat but the heater
has not yet started.
Water temperature can be adjusted by 1˚ in-
crements from 59 to 104˚F (15 to 40˚C).
N.B.: If your system is configured in Low Current Mode,
the heater will not start if a pump is on at high speed.
Temperature display unit:
Press and hold Light key for 5 seconds to display
water temperature in either Fahrenheit (˚F) or
Celsius (˚C). If a power-up occurs, system re-
turns to default setting (˚F).
Economy mode:
Press Econo key to switch from Normal mode to
Economy mode. In Economy mode, system main-
tains temperature at the desired Set Point during
filter cycles only. Set Point is 20˚F (11˚C) below
the Normal mode Set Point for the rest of the
time. In Economy mode, the display will toggle
between the current water temperature and the
"Econ" message.
Quick Reference Card
|