40 Oz. Steam Cleaner
OWNER’S MANUAL
Model EP922HA
120V., 60 Hz, 1550 Watts
EURO-PRO Operating LLC
94 Main Mill Street, Door 16
Plattsburgh, NY 12901
Tel.: 1 (800) 798-7398
TIPS ON HOW TO USE YOUR SYSTEM
IMPORTANT SAFETY INSTRUCTIONS
Hints
Blinds
When using your Steam Cleaner, basic safety precautions should always be
Use the nylon bristle brush to clean
blinds. Move the brush over the
surface, allowing enough time for the
vapor to penetrate. Work quickly on
PVC blinds. Test for color fastness on
fabric blinds before using. Finish by
wiping with a towel.
observed, including the following:
ALWAYS FINISH CLEANING BY WIPING
DOWN THE CLEANED SURFACE WITH A
TOWEL
To reduce the risk of fire, electric shock, or
injury:
1. Read all instructions before using your
steam cleaner.
2. Use the system only for its intended use.
3. To protect against a risk of electric shock,
do not immerse any part of the system in
water or other liquids.
4. Never yank cord to disconnect from
outlet; instead, grasp plug and pull to
disconnect.
•
Do not leave the steam cleaner plugged
in when unattended. Unplug the electrical
cord when not in use and before servicing or
refilling water tank.
The steam cleaner has many uses that
have not been mentioned. This was
meant only to give you a general idea of
what can be achieved with the unit.
However, the ways in which to use the
attachments and brushes are in most
cases universal. It is most helpful to
always have a terry cloth towel or paper
towel ready to use for removal of
moisture and residue. 100% white
cotton towels work best.
You can clean the brushes with your
steam cleaner. When cleaning the detail
brush, use a pair of pliers to hold and
blow dirt as above or place in the basket
of your dishwasher.
Automotive
•
•
•
Do not allow to be used as a toy. Close
attention is necessary when used near
children, pets or plants.
Use only as described in this manual. Use
only manufacturer’s recommended
accessories.
Do not pull cord, use cord as a handle, close
a door on cord, or pull cord around sharp
edges or corners. Keep cord away from
heated surfaces.
For detailing the wheels, use the
concentrator and the bristle brush.
Exterior windows are cleaned best by
using the window squeegee.
To clean bicycles, use the bristle brush.
To clean equipment, use the bristle
brush, depending on the surface area.
Finish by wiping down with a towel.
Artificial Plants
5. Do not allow cord to touch hot surfaces.
Let the system cool completely before
putting away or opening water tank
(removing the safety cap). Wrap cord
loosely around system when storing.
6. Always disconnect system from electrical
outlet when filling with water or emptying
and when not in use. Always turn the
safety cap slowly when opening the water
tank . This will allow any remaining steam
to escape gradually.
7. Do not operate the system with a damaged
cord or plug, or if the appliance or any other
part of the system has been dropped or
damaged. To avoid the risk of electric
shock, do not disassemble or attempt to
repair the steam cleaner. Return the
system to EURO-PRO Operating LLC (see
warranty) for examination and repair.
Incorrect re-assembly or repair can cause a
risk of electrical shock or injury to persons
when the steam cleaner is used.
8. Close supervision is necessary for any
appliance being used by or near children.
Do not leave the system unattended while
connected to electrical outlet or when hot.
9. Burns can occur from touching hot metal
parts, hot water or steam. Use caution
when draining unit after use as there may
be hot water in the unit. Never direct steam
at any person. The steam is very hot and
can cause burns.
10. Do not operate in the presence of
explosive and/or flammable fumes.
11. This appliance is intended only for
household use. Follow all user instructions
in this manual.
•
•
•
•
•
•
Do not use extension cords or outlets with
inadequate current carrying capacity.
Do turn off all controls as applicable before
unplugging from electrical outlet.
Do not unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
Do not handle plug or steam cleaner with wet
hands or operate without shoes.
Do not put any objects into openings. Do not
use with any opening blocked.
Use the concentrator without a brush
attached to blow off the dust and dirt.
Clothing
A vapor cleaning system is excellent for
removing wrinkles from fabrics. Simply
“vaporize” the surface from a distance
(12”-18”) and pull or stretch the fabric to
remove the wrinkles. The dry vapor
removes wrinkles without leaving the
fabric wet like ordinary fabric steamers
do.
Note: Wipe with a towel immediately
before the cleaned area dries. When
cleaning the oven, use the detail brush
to clean around the elements and drip
trays. Use the detail brush for cracks,
crevices, and hard to reach areas.
ALWAYS STORE YOUR APPLIANCE
INDOORS in a cool, dry area.
•
•
Do keep your work area well lit.
Refrigerator - Use the concentrator to
blow away dirt in the ice machine and
on door seals. The vapor will not dry
out or crack the seals as chemicals
often do. Can openers and other
kitchen equipment can be easily
cleaned with the detail brush to get into
all the nooks and crannies. Mold stains
around door gaskets can be removed
with the detail brush.
To clean microwaves or other small
appliances use the detail brush for
small areas.
Note: When cleaning small electrical
appliances always unplug them from
outlet before cleaning.
Do Not turn the appliance over or on its
side. Never direct steam towards people,
animals or plants.
Nicotine and Tar
Nicotine and tar dissolves at high
temperatures and becomes a light
yellow oil that has the consistency of
sewing machine oil. When the
nicotine/tar film is touched by steam
pocket, it immediately dissolves and
flows into the steam pocket towel. You
can remove it from flat surfaces as fast
as you can move the steam pocket over
the surface.
•
•
Do not immerse the steam cleaner into water
or other liquids. Always unplug the power
cord from the electrical socket when filling the
steam cleaner.
Do NOT add cleaning solutions, scented
perfumes, oils or any other chemicals to
the water used in this appliance as this
may damage the unit or make it unsafe for
use. Use tap water or distilled/purified
water if the tap water in your area is very hard.
Removing Wax, Tar, Etc.
Many stains are only stuck on the
surface of materials and can be easily
and quickly removed by “blowing”
excess material away from the surface
from the side. This is accomplished by
using the concentrator. Hold the terry
cloth towel to the side to catch the loose
residue as it is blown by the
12. Never use any chemicals or substance
other than tap water in the machine. Use of
chemicals may damage the machine. Use
of chemicals will automatically void your
warranty.
To clean counter tops, use the steam
pocket frame and steam pocket. For
heavily soiled areas, use the detail
brush first in order to loosen the debris,
then follow with a terry cloth towel to
finish.
concentrator. Note: Always vacuum
any loose residue off the surface before
you apply vapor to it.
SAVE THESE INSTRUCTIONS
For Household Use Only
12
1
Rev. 05/05
TIPS ON HOW TO USE YOUR SYSTEM
ADDITIONAL IMPORTANT SAFEGUARDS
Fiberglass or Stainless Steel Surfaces
1. To avoid circuit overload, do not operate another appliance on the same socket
(circuit) as the steam cleaner.
2. If an extension cord is absolutely necessary, an extension cord rated a minimum
of 15 ampere, 14 gage cord should be used. Cords rated for less amperage may
overheat. Care should be taken to arrange cord so that it cannot be pulled or
tripped over.
Spot Cleaning (Carpets)
Use the bristle brush. Slowly move the
brush over the surface to be cleaned.
The vapor will emulsify the dirt and
grease on the surface. Follow behind
with a terry cloth towel over the brush to
remove excess moisture and residue.
Tip: An old idea for polishing stainless
steel is to wipe it down with seltzer soda
water after it is cleaned.
Use the concentrator with or without the
bristle brush. Move slowly over the soiled
area, allowing the steam to penetrate.
Agitate with bristle brush or clean towel.
Dab the spot with the towel (do not rub).
Repeat as necessary to remove stain.
Vacuum only after the carpet has
completely dried.
Always test color fastness of carpet in an
inconspicuous area before cleaning.
If your steam cleaner fails to remove
stubborn stains a commercially available
carpet shampoo may be required. Do
NOT add cleaning solutions, scented
perfumes, oils or any other chemicals to
the water used in this appliance as this
may damage the unit or make it unsafe
for use.
CAUTION: Always determine the color-
fastness of any fabric-especially with
reds or blues - by taking a clean, moist,
warm towel and gently rubbing a small
area as far down on the back or other out
of the way place on the furniture as
possible. If color comes off on the towel,
you may need to have the piece dry
cleaned.
3. Do not leave unattended when the system is connected to a power
supply/electrical outlet.
Bathroom Areas
WARNING: This appliance is equipped with a grounded-
type 3-wire cord (3-prong plug). This plug will only fit into an
electrical outlet made for a 3-prong plug. This is a safety
feature. If the plug should fail to fit the outlet, contact an
electrician to replace the outlet. Do not attempt to defeat the
safety purpose of the grounding pin, part of the 3-prong plug.
To clean the bathtub or shower area, use
the bristle brush for grout, shower door
tracks, hard to get areas and heavily
soiled areas. The window squeegee will
be the most efficient way to clean the rest
of the area. Allow plenty of time for the
heat to penetrate the surface. This is
especially helpful in the shower area if
there is tile or grout. Wipe with towel.
Removal of soap scum on tile, grout, and
shower doors is also easier with the
steam cleaner.
To clean sanitary fixtures, use the
concentrator with or without bristle brush.
Use a terry cloth towel or paper towel to
wipe up excess moisture and residue.
To clean the sink and faucets, use bristle
brush then finish by wiping with a towel.
Soap Scum
Soap scum dissolves almost immediately
under a combination of heat and
moisture. Rinse the surface with a small
amount of water afterwards or go back
over it once more with a clean terry cloth
towel.
Note: Soap scum sometimes will
develop a hard surface from waterborne
minerals. If this is the case, use the
bristle brush to break up this surface - or
spray or wipe first with lemon, vinegar or
seltzer soda water to soften the minerals.
Moving too slowly can dry out the soap
scum and cause it to granulate on the
surface. The surface will have a gritty
feel. If this happens, apply vapor to the
surface with the bristle brush again and
re-clean.
CAUTION: Always drain condensed water from hose
before use or if unit has been left idle for a period of time. To
drain hose, direct nozzle into an appropriate container or sink
and depress hand grip steam trigger. Once hose has been
drained, normal use may be resumed. Never direct nozzle
towards people, animals or plants.
WARNING: Your Steam Cleaner is designed to clean hard surfaces
and upholstery that will withstand high heat. Do not use on soft plastics
and cold glass. On surfaces that have been treated with wax or some no
wax floors, the sheen may be removed by the heat and steam action. Do
not use on unsealed wood. This could cause the wood grain to rise. It is
therefore recommended to test an isolated area of the surface to be
cleaned before proceeding.
Window, Glass Surfaces and Mirrors
Use the window squeegee. Work with
the vapor jet on using the top to bottom
movements. Use the squeegee with the
vapor off to clear the water from the
glass. To do this without leaving streaks,
use lateral movements from the top to
the bottom of the surface.
CAUTION: When cleaning windows,
always avoid any sudden changes in
temperature to prevent glass breakage or
cracks.
IMPORTANT: Do NOT add cleaning solutions, scented perfumes, oils or
any other chemicals to the water used in this appliance.
Use regular water or distilled/purified water if the tap
water in your area is very hard.
WARNING: Danger of Scalding. Please use caution when using
the steam cleaner. The steam emitted from this aperture is very
hot.
Garden Furniture
Use the brushes depending on the
surface area. Work quickly when
cleaning resin outdoor furniture. Finish by
wiping with a towel.
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
2
11
TIPS ON HOW TO USE YOUR SYSTEM
GETTING TO KNOW YOUR STEAM CLEANER
Water
Wood, Vinyl and Marble Floors
Use the steam pocket. Move the steam
pocket across the floor as if you are
•
Use tap water for all your cleaning
needs.
•
However, if you live in an area with
hard water, use de-mineralized /
distilled water when steaming light
colored fabrics to eliminate the
possibility of hard water stains.
mopping. When one side of the towel is
soiled, turn the steam pocket frame and
use the other side. If you are working
on a very dirty area, you can move the
steam pocket over the area slowly,
several times. If it is a wood floor, move
fast to avoid heat or moisture buildup in
the wood.
To Clean Waxed Floors: Use the
steam pocket with quick strokes. This
will cause the dirt to be removed but not
the wax.
IMPORTANT: Do NOT add cleaning
solutions, scented perfumes, oils or any
other chemicals to the water used in
this appliance. Use tap water or
distilled/purified water if the tap
water in your area is very hard.
WARNING: A towel wrapped
around the steam pocket frame
Vinyl Floors: Do not allow heat to
buildup in any kind of vinyl, since it can
soften it enough to affect its texture.
Work fast on vinyl.
can become hot enough to burn. Make
sure that you let the towel cool off for 5
minutes before touching it.
Using Towels
•
For best results use 100% cotton
white terry cloth towels.
Tile Floors: Use the concentrator with
the bristle brush attached to an
extension. Have the steam pocket
ready as well. Clean the grout between
the tiles with the bristle brush. Remove
the bristle brush and attach the steam
pocket, move the steam pocket across
the floor to clean the tile and remove
excess moisture and residue. Do not let
the area dry before you wipe with a
towel.
•
The purpose of using a towel is to
absorb moisture and dirt being
removed. Always use dry towels.
A wet towel will smear the dirt.
Wash towels with strong detergent
and bleach.
Using scented fabric softener while
washing the towels will cause the
scent to be released into the air
when using the towels with your
steam system.
•
•
Efficient Work
•
For vertical surfaces, wipe with a
towel from the top down, in this
way the dirty water will not soil
surfaces already cleaned.
Avoid changing brushes back and
forth while cleaning.
Start with the smallest brush to
clean tight spots and corners first.
Use a towel to wipe dirt as soon as
possible, otherwise it will dry and
re-adhere to the surface.
1. Safety Filler Cap
10. Power Cord
2. Shoulder Strap
3. Power “On” Light (Red)
4. Steam Ready Light (Green)
5. Flexible Hose
6. Hand Grip
7. Steam Switch
11. Extension Tubes (x2)
12. Window Squeegee
13. Steam Pocket Frame
14. Micro-fiber Steam Pocket
15. Micro-fiber Towel
16. Concentrator
17. Detail Brushes (x2)
18. Casters (x4)
19. Funnel
•
•
•
8. Variable Steam
9. Locking Button
Technical Specifications
Voltage:
Power:
120V., 60Hz.
1550 Watts
Water Capacity:
Steam Generator:
40 US Fl. Oz. (1200 ml.)
Stainless Steel
3
10
FEATURES OF STEAM CLEANER
CARE & MAINTENANCE
If you consistently use demineralized or
distilled water, cleaning the tank is
unnecessary.
To Descale the Steam Cleaner
Step 1: Unplug the steam cleaner from
the power source before you
5. Variable Steam:
Allows you to adapt the
steam flow to the job.
1. No more detergents or
chemicals. Just add water.
descale the boiler. Allow to cool.
Rinsing Out the Steam Cleaner
Normally, a periodic rinse of your steam
cleaner will free it from deposits. This is
recommended every 10-15 tankfulls, to
free up any scale deposits from the tank.
Fill the boiler with 20 oz. of water and
shake the cleaner vigorously. Tilt the
cleaner upside down to empty the boiler of
water and any scale deposits.
Step 2: Fill the boiler with 1 part
vinegar and 5 parts water and
leave overnight or for a period
of approximately 8 hours. Do
not screw the safety/filler cap
onto the steam cleaner while
you are descaling the boiler.
Do not use the steam cleaner
while descaling solution is
inside the boiler.
2. Portable
Descaling Your Steam Cleaner
If the tap water in you area contains a high
level of calcium deposits and you have
been using tap water to do your steam
cleaning, you should descale your unit
after 10-15 tankfulls.
Step 3: After the period of soaking, turn
the steam cleaner upside down
to empty solution from the
6. Versatile, quick-change
accessories
boiler. Due to the fact that a
small amount of solution will be
left in the boiler, it is necessary
to rinse the boiler out with clean
water 2 or 3 times. Your steam
cleaner is now ready for use.
3. Stainless Steel Boiler:
Non-corroding, stainless
steel boiler. Welded
construction.
6. Indoor and Outdoor Use:
Bathrooms, kitchens, living
areas, pet areas and
appliances.
Automotive, patio and
windows.
4. Heavy-duty crush-resistant
hose.
4
9
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Attaching the Shoulder Strap
Attaching the Casters to the
Steam Cleaner
Care & Maintenance of the Steam
Pocket Towel
Due to the unique cleaning ability of this
cloth, proper care of your micro-fiber towel
is required to ensure long life and continued
cleaning ability.
• The first thing you should do when
you get a new micro-fiber towel is to
wash and dry it. During the manufacturing
process the fabric has a tendency to
become flat as it picks up contaminants
from the air and machinery. There will
also be a number of loose threads that,
while they cause no harm, can be
annoying the first time you use the towel.
• To clean the towel, simply wash it in your
washing machine using the warm water
setting.
CAUTION: Be aware of hand placement
and take care not to actuate the steam
discharge switch while installing or
removing accessories.
Using the detachable shoulder strap
allows for greater freedom of movement
when both hands are needed for
various cleaning tasks.
To attach the shoulder strap to the
steam cleaner, simply snap the
shoulder strap hooks onto the
connecting rings on the unit body.
See Fig. 1, 2 & 3.
The casters for the steam cleaner are
packed and shipped unassembled. To
assemble the casters to the steam
cleaner, simply snap the casters onto
the pegs that are in the base of the
unit. (Fig. 4) Repeat for the next three
(3) casters.
Attaching the Accessories to the
Flexible Steam Hose
NOTE: Allow the unit to cool for 5 minutes
before changing accessories.
Window Squeegee
Connection
Points
This attachment is very useful for
cleaning large windows, plastic material,
ceramic, tiled or marble surfaces.
To use: Connect the tile
Fig. 1
squeegee to the hand
grip or use with
extension tube for
hard to reach surfaces.
• Always wash your towels separately from
other fabrics. They have a tendency to
pick up lint and other particles from other
fabrics and the next time you use your
towel, this lint will transfer to the surface
being cleaned.
• ONLY USE LIQUID DETERGENTS,
never use dry detergents as many times
the granules do not fully dissolve and
become trapped in the towel. This can
scratch the surface that you are cleaning.
• NEVER USE BLEACH OR FABRIC
SOFTENERS! Bleach will damage the
micro-fiber fabric and fabric softeners
deposit a coating on the micro-fiber fabric
that will not allow the cloth to clean
efficiently.
• Air dry the towel. Do not put in a clothes
dryer as high heat will cause the towel to
shrink and the micro-fibers to break down.
• If you wash your towels on a regular basis
and don’t let them get too dirty, they will
last much longer. As with any fabric, dirt
particles, grease and other contaminants
can cause the fibers to break down,
therefore regular cleaning will help
preserve your micro-fiber towels.
• As you use the micro-fiber towel, you will
notice that sometimes a thread will loosen
or pull out. This is normal and you should
NEVER PULL AT THE LOOSE
Apply steam abundantly, rub with the
soft spongy edge, then remove excess
water and dirt with the glass wiping
edge.
Fig. 4
IMPORTANT: When cleaning
windows, always avoid any sudden
changes in temperature to prevent glass
breakage or cracks.
Fig. 2
After you have inserted the castors to
the base of the steam cleaner, turn the
unit right side up on a flat, level
surface.
Concentrator
Attach the concentrator
to the handgrip or to the
extension tubes. Then
attach the detail brushes
to the concentrator.
IMPORTANT: Always insert the
casters before you fill the unit.
Detail Brush
It is best for cleaning grout in-between
the tiles, ceramic and marble.
To use: Attach the detail
brush on to the end of the
concentrator, which
then may be used directly
on the hand grip or with extension tubes
Micro-Fiber Towel
It is best for cleaning up
after using the steam
Fig. 3
accessories. Lifting the
dirt away from the surface
To clean: Follow the cleaning
instructions for the steam pocket.
IMPORTANT: When using the
steam cleaner with the shoulder
strap, avoid rocking or tilting the
unit excessively as this may
cause water to enter the hose
and be discharged along with the
steam.
THREAD! Pulling the thread can cause
the weave to come undone. Instead,
simply trim the thread with a pair of sharp
scissors.
8
5
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Components
Note that the flat on the nozzle
Using the Variable Steam
Feature
Remove the funnel slowly and let
the remaining water in it to go
inside the water tank. Do Not
Overfill. Replace the Safety
Filler Cap.
must face toward the side of the
frame with the brass pin. Once
inserted, rotate it 90°.
Power “On” Light (red): This light will
illuminate when the unit is plugged into
the 120V. wall outlet. This light will cycle
on and off with the steam ready light.
CAUTION: Read the instructions
for “Filling the Water Tank” before
opening the Safety Cap.
Your steam cleaner has a variable
steam feature that allows you to adjust
the steam flow to the job that you are
doing. For example, set the variable
steam at lower settings when using
the window squeegee and at higher
settings when cleaning grout seams.
The variable steam control is located
on the handgrip. Fig. 6 To increase the
steam flow, turn the knob counter
clockwise and to decrease, turn it
clockwise.
Step 3: Insert the electrical power cord
into the outlet. Heating time
is approximately 8-10 minutes
with cold water. Filling the steam
generator with hot water will
shorten the heat up time.
Attaching the Steam Pocket
Towel to the Frame
WARNING: Always insure the unit is
“UNPLUGGED” from the wall
receptacle prior to attaching or
removing accessories.
WARNING: Allow unit to cool for
15 minutes before refilling. When
refilling the steam cleaner while the
boiler is still hot, there is a risk that
water will squirt back during filling
and cause scalding. Extreme care
should be taken when refilling the
unit. Use caution when opening the
Safety/Filler Cap as cap may become
hot during use and escaping steam
can cause scalding.
CAUTION: Always unplug
before filling. ALLOW UNIT TO
COOL FOR FIFTEEN (15)
MINUTES BEFORE REFILLING.
IMPORTANT: Do NOT add cleaning
solutions, scented perfumes, oils or any
other chemicals to the water used in this
appliance. Use tap water or
distilled/purified water if the tap water
in your area is very hard.
Step 6: Connect desired attachments
onto the Flexible Steam Hose.
Step 7: Plug the unit into a standard (120
volt, grounded) wall receptacle.
Allow approximately 8-10 minutes
for vapor to reach its working
1. Slide the steam
pocket towel over
the steam pocket
frame. (Fig. 10)
Filling or Refilling Your Steam
Cleaner With Water
Fig. 6
IMPORTANT: Always insure that the unit
is “UNPLUGGED” from the wall receptacle
prior to initial filling or re-filling the water
tank and has been allowed to cool for 15
minutes. Never attempt to fill this unit
under a water tap, always use the filling
funnel provided.
Using Your Steam Cleaner with
Steam Pocket
Fig. 10
temperature and pressure. The
green ready light will illuminate
when the unit is ready for use.
Always point nozzle outlet in a safe
direction.
2. Bring the towel all
the way to the top
of the steam
Step 1: Connect one of the extension
tubes to the hand grip on the
flexible steam hose. To
pocket frame.
attach the extension tubes
one onto the other or onto the
hand grip, press the locking
button ensuring that it fits into the
hole. (Fig. 7, Fig. 8) To
disconnect, repeat the operation
by pressing the locking button
and pulling the two sections
apart.
(Fig. 11)
Fig.11
Step 1: Before refilling the steam cleaner,
make sure that the unit is NOT
plugged in and has been allowed
to cool for fifteen (15) minutes.
Step 2: Plug the power cord in to an
electrical outlet and press the
steam switch on the hand grip to
the “ON” position to vent of any
residual steam that is in the boiler.
Step 3: Remove the power cord from the
electrical outlet and turn the steam
switch on the hand grip to the
“OFF” position.
Step 4: Place the unit on a flat, stable
surface. Slowly turn the safety
filler cap counter clockwise until it
is removed.
Step 5: Insert the funnel into the tank
opening and add 40 US Fl, Oz.
(1200 ml) of water. Place the
funnel in the tank opening as
illustrated in Fig. 5. The funnel has
been specially designed to show
when the water tank is full. When
water starts to come out of the
vent hole of the funnel, the tank is
full.
NOTE: When the steam cleaner has run
out of water, steam output will cease.
3. Bring the velcro strips
that are on the
back side of the
steam pocket towel
over the steam pocket
frame and attach to
the inside of the
Fig. 5
front side of the
steam pocket towel. (Fig. 12)
Fig. 12
NOTE: If replacing the steam pocket
towel, make sure that the steam pocket
frame has been allowed to cool before
removing or attaching a new steam
pocket towel.
Fig. 8
Fig. 7
NOTE: Fit the steam pocket frame with
the angle adapter onto the extension tube.
Step 2: If the angle adapter is not
attached to the steam pocket
frame, attach as follows: Hold
the steam pocket frame in one
hand and the
WARNING:Allow unit to cool
for 15 minutes before refilling.
Use caution when opening the
Safety/Filler Cap as cap may
become hot during use and
escaping steam can cause
scalding.
angle adapter in
other. Insert the
angle adapter
stem into the
opening of the
steam pocket frame as
shown in Fig. 9
Fig. 9
6
7
|