ED200
INSTRUCTION
MANUAL
?Follow all warnings and instructions marked on the appliance.
?Do not overload wall outlets and extension cords as this
can result in fire or electric shock.
?Never push objects of any kind into his appliance through
cabinet slots as they mat touch dangerous voltage points or short
out parts that could result in fire or electric shock.
?Do not place this appliance on an unstable cart, stand,or table.
?The appliance may fall, causing serious injury to a child or
adult, and serious damage to the appliance.Use only with a cart
or stand recommended by the manufacturer,or sold with the
appliance.Wall or shelf mounting should follow the
manufacturer’s instructions, and should use a mounting kit
approved by the manufacturer. An appliance and cart combination
should be moved with care, Quick stops, excessive force,
2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER ( OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERRSONNEL.
The lightning flash with an arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the presence
of non-insulated ”dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
This symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
3
Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection. This equipment generates,
uses and can radiated radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase these paration between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
4
I. General
The ED200 Series Camera is a compact, full functioned CCD
Camera. Their stylish appearance can be applied as per installer's
ideal locations. These dome cameras can be mounted either on the
ceiling or on the wall easily. ED200 uses high sensitive 1/3" color
interline transfer CCD sensor with DSP. The sensor is featured
with Auto Electronic Shutter, Automatic Gain Control, and Auto
White Balance function.
II. Precautions
• Do not expose the camera to humidity and dust. Outdoor
application without shielding is not recommended.
• Handle with care. This camera consists of sensitive high
precision parts. Do not disassemble or install it on an
unstable base.
• Operate on DC +12V. Use a regulated power source only.
• The external adapter is optional.
• Never face the camera toward the sun directly.
5
III. Lens Available
* Standard board lens f=3.6 mm, F=2.0 mm.
* Other available lens : -2 Lens f=2.5 mm, F=2.0 mm
-4 Lens f=4.3 mm, F=2.0 mm
-6 Lens f=6.0 mm, F=2.0 mm
-8 Lens f=8.0 mm, F=2.0 mm
-3P Pinhole lens f=3.7 mm, F=3.0 mm
IV. Installation Instructions
1. Remove the plastic dome cover.
2. Loosen the two screws of the supporting bracket to
remove the camera body.
3. Using four screws to fix the camera base on the ceiling.
4. Put the camera body back to the supporting bracket, the
connector of the back panel should always be placed to
camera’s left lower corner, in order to obtain the image of
best quality. Tighten the 2 screws to fix the camera. Please
refer to the back panel diagram shows as below:
6
a. Floor Mount
b. Ceiling Mount
d. Wall mount,
aim to the left
c. Wall mount,
aim to the right
5.
Connect the BNC connector of the camera to a color
monitor, or other video device through a 75 ohm
type coaxial cable with BNC female connector at
cable extension.
7
6.
7.
Connect the DC +12V regulated power source
of the camera (DC Jack) to the DC 12V Power-
in jack with 2 mm, center+, outer- plug.
Once the image appears on the monitor, loosen
the fixing screw located at the lens mount then
adjust the focus and diaphragm of the lens to
obtain the best picture. When the ideal picture is
obtained, secure the lens mount by fixing screw
firmly again.
8.
Put the plastic cover back on the Dome Camera.
8
V. Specifications
Pickup device:
1/3“ interline transfer CCD
510 x 492 (NTSC)
Picture element:
500 x 582 (PAL)
Horizontal resolution: 380 TV Lines
Sensitivity:
0.3 Lux/F=1.2
Over 48 dB
Up to 1/100,000
Yes
S/N ratio:
Electronic shutter:
Auto white balance:
Gamma correction:
Video output:
Power source:
Sync. Mode:
0.45
1.0Vp -p, 75 ohm
12V DC ? 10%
Internal Sync.
Lens mount:
Dimension:
M12 x P0.5
106 mm (D) x 85 mm (H)
Operating temperature:-10°C to +50°C
Power consumption: 3W
9
VI. Package Contents
•
•
ED200 Camera unit
User’s manual
10
EverFocus Electronics Corp.
Head Office:
China Office:
12F, No.79 Sec. 1 Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: +886-2-26982334
FAX: +886-2-26982380
www.everfocus.com.tw
Room 609, Technology Trade Building,
Shandgdi Information Industry Base,
Haidian District, Beijing,China
TEL: +86-10-62971096
FAX: +86- 10-62971432
USA Office:
www.everfocus.com.cn
1801 Highland Ave. Unit A
Duarte, CA 91010, U.S.A.
TEL: +1-626-844- 8888
FAX: +1-626-844-8838
www.everfocus.com
Japan Office:
1809 WBG MARIBU East 18F,
2-6 Nakase.Mihama- ku.
Chiba city 261-7118, Japan
TEL : +81-43-212-8188
European Office:
Albert-Einstein-Strasse 1
D-46446Emmerich, Germany
TEL: 49-2822-9394-0
FAX: 49-2822939495
www.everfocus.de
FAX : +81-43- 297-0081
www.everfocus.com
Ihr EverFocus Produkt wurde
Your EverFocus product is designed
and manufactured with high quality
materials and components which can
entwickelt und hergestellt mit
qualitativ hochwertigen Materialien
und Komponenten, die recycelt und
wieder verwendet werden können.
be recycled and reused.
This symbol means that electrical
and electronic equipment, at their
end-of -life, should be disposed of
separately from your household
waste.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte
am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Please, dispose of this equipment at
your local community waste
Bitte entsorgen Sie dieses Ger ät bei
collection/recycling centre.
Ihrer ö rtlichen kommunalen
Sammelstelle oder im Recycling
In the European Union there are
separate collection systems for used
electrical and electronic product.
Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
Please, help us to conserve the
environment we live in!
P/N: MED2G0040A
|