USEnglisch.bk : Griff.fm5 Seite 1 Freitag, Februar 1, 2002 10:33 AM
Operation Guide
Mode d’emploi
ENGLISH
FRANCAIS
USEnglisch.bk : Inhalt.fm5 Seite 3 Freitag, Februar 1, 2002 10:33 AM
Contents
CD/MD Changer Operation
19
Compact Disc (CD) instructions
Operational readiness of CD/MD changer
CD magazine - load / unload
Playing CD/MDs
19
19
20
20
21
21
21
Track skip - forwards / reverse
Scan search
Fast forward / rewind
Relative time, number of tracks, total playing time 22
Random play
Direct track selection
22
22
User Menu
23
User menu - request / quit
DRIVER setting
User memory
23
23
24
24
24
25
25
26
LED setting
GAL setting
Telephone mute characteristics (PHONE)
Viewing angle setting (ANGLE)
Country setting (COUNTRY)
Connection Instructions
General Instructions
27
28
RBDS system
PTY (Program Type)
28
28
Technical Data
29
3
USEnglisch.bk : TASTEN.fm Seite 4 Freitag, Februar 1, 2002 10:33 AM
Bottom Arrangements
2
8
3
4
5
6
7
9
1
10
11
12
1
Volume control
On / off switch (
Tone button (
9
Tape eject button (
)
2
3
4
5
6
7
8
)
10 Right rotary control
11 Multifunction buttons
12 Display
)
Road traffic announcement button (
LED
Operating mode switching button (
)
Mode)
Function button (
Waveband switching button (
)
Band)
4
USEnglisch.bk : DIEB.fm Seite 5 Freitag, Februar 1, 2002 10:33 AM
Anti-theft Device
Code number entry
If the car radio is disconnected from the power supply, it is theft-protected upon
reconnection. After switching on at the
followed by 4 stars is displayed.
The four-digit code must then be entered using the multifunction buttons “1-0”.
button, the prompt CODE,
Example : Code number 1530 (the code number can be found on the enclosed
CODE CARD).
Enter code number using the multifunction buttons.
The first star is extinguished after entry of the first digit. The second star is
extinguished after entry of the second digit, etc. The unit switches on
automatically after entry of the 4th digit if this and all other digits have been
correctly entered.
Note :
It is essential that the CODE CARD be kept in a safe place outside
the vehicle. Thus, illegal use is not possible. The accompanying
sticker should be attached to the inside of the vehicle windshield/
window.
If an incorrect code number is entered, the prompt CODE with the four stars is
displayed again. After entering incorrect code three times WAIT is displayed
and the unit is disabled for approx. 60 minutes. Three further incorrect entries
block the unit again for 60 minutes.
Note :
The waiting time applies only to ignition and unit switched on.
5
USEnglisch.bk : DIEB.fm Seite 6 Freitag, Februar 1, 2002 10:33 AM
Anti-theft Device
Remove portable panel
As an effective anti-theft device, the portable panel (A) can be removed from
the unit.
For this purpose, press and hold
The portable component can then be pulled out.
button. The display folds forwards.
The volume is limited to a maximum value after the display has been folded
down. After 20 seconds an audible signal indicates that the control component
is folded down. The unit is switched to mute. The unit switches off after a
further 10 seconds.
A
Note :
Note :
For safety reasons, it is not permissible to leave the portable panel
open when driving
Please insert the portable panel in the accompanying protective
cover after removal.
Do not touch the metal contacts on the portable panel or on the
radio.
Inserting portable panel
Insert the portable panel so that it engages first in the lower left catch and then
in the lower right. Then press the portable panel into the upper catches.
Or position portable panel directly over all four catches and press in firmly to
engage.
For proper functioning, ensure that the portable panel is firmly engaged in all
four catches.
If a new portable panel or one from another unit is utilised, the code number
must be entered, as previously described, in order to activate the unit.
6
USEnglisch.bk : Allgemeine.fm Seite 7 Freitag, Februar 1, 2002 10:33 AM
General Operation
Switch on / off
Press
button.
Further on / off switching possibilities: Via ignition. In order to switch on via
the ignition, the unit must previously have been switched off via the ignition.
After switching off the ignition, the unit can be prevented from switching off
by pressing the
button within 3 seconds.
Note :
The unit can also be switched on with the ignition switched off via
the button, but will switch off automatically after 1 hour.
Adjust volume
Turn volume control to right / left. The volume is increased or decreased. The
current volume level is shown on the display.
Mute function
The unit can be switched to mute in each operating mode by pressing the
volume control. MUTE appears on the display.
The mute function is cancelled by pressing the volume control, changing the
operating mode, changing the waveband or inserting a tape/CD.
Activate tone menu
Press
button. The tone menu is activated. The following functions can be
called up: BASS (Bass), TREB (Treble), BAL (Balance), FAD (Fader),
LOUD (Loudness) and STEREO (Reception optimization).
Bass and treble settings for the AM/FM wavebands, for road traffic
announcements and tape/CD operation are stored separately (values from -7 to
+7). The settings for fader, balance and loudness (no loudness with AM) are
stored together for all operating modes (values from -7 to +7).
7
USEnglisch.bk : Allgemeine.fm Seite 8 Freitag, Februar 1, 2002 10:33 AM
General Operation
Adjust bass
Press
button and then multifunction button “-” or “+”. BASS and the set
value are displayed. Set the desired bass via both buttons.
Center setting: Press both buttons simultaneously.
Adjust treble
Press
button and then multifunction button “-” or “+”. TREB and the set
value are displayed. Set the desired treble via both buttons.
Center setting: Press both buttons simultaneously.
Adjust balance
Press button and then multifunction button “ ” or “ ”. BAL and the set
value are displayed. Set the desired balance via both buttons.
Center setting: Press both buttons simultaneously.
Fader
Press button and then multifunction button “ ” or “ ”. FAD and the set
value are displayed. Set the desired fade level via both buttons.
Center setting: Press both buttons simultaneously.
8
USEnglisch.bk : Allgemeine.fm Seite 9 Freitag, Februar 1, 2002 10:33 AM
General Operation
Loudness on /off
Press button and then multifunction button “LD”. LOUD ON or LOUD
OFF are displayed. The loudness can be switched on or off alternately by
pressing the multifunction button.
Linear adjustment
Activate tone menu. Then again press and hold button for more than 2
seconds. The tone values for the set signal source (e.g. radio/FM) are set to an
average value FM LINEAR.
Press and hold button for more than 4 seconds. All tone values for the
signal sources radio and tape / CD are set to an average value ALL LINEAR.
Adjust mono / stereo
Three different reception optimisation settings can be set in order to suppress
reception dependent interference and reflections.
Repeatedly press multifunction button “ST” in tone menu until the desired
optimisation is set.
AUTO: Setting for normal operation - i.e., the unit switches from stereo to
mono and back depending upon reception location (provides the optimum
setting for almost all reception areas).
STEREO: Setting for unusal reception situations - i.e. the unit is set
permanently to stereo (e.g. for private radio stations in city areas)
MONO: Setting for reception conditions in which reflections constantly occur
- i.e., the unit is set constantly to mono.
The setting is effective immediately after pressing the multifunction button
“ST” and is also retained on switching off.
9
USEnglisch.bk : RUNDFUNK.fm Seite 10 Freitag, Februar 1, 2002 10:33 AM
Radio Operation
Select operating mode
Press button. The operating modes Radio, TAPE or CD/MD changer (for
connected CD/MD changer) can be selected.
The last selected operating mode is selected after the button is pressed for the
first time. If the other operating modes are to be selected, press the
quickly and repeatedly until the desired operating mode is selected.
button
Note :
If you switch often between FM and TAPE, first select FM and
then through quick pressing TAPE. Subsequently, press the
button after a pause of more than 2 seconds, switching only takes
place between FM and TAPE.
Select waveband
Press
selected.
When changing the waveband, the last selected station is selected.
button repeatedly until desired waveband FM 1, FM 2 or AM is
Switch on radio menu mode
Press
button. The radio menu mode is switched on and displayed. The unit
switches back to the normal display if no buttons are pressed within the next 8
seconds.
10
USEnglisch.bk : RUNDFUNK.fm Seite 11 Freitag, Februar 1, 2002 10:33 AM
Radio Operation
Setting procedures for station selection
The desired broadcasting station can be selected via station search, scan search,
manual tuning, autostore, direct frequency input and station buttons.
FM, AM station search
Turn the right rotary control to the left/right in desired waveband. The radio
searches in descending/ascending order.
Scan search
In the desired waveband (FM or AM) press the right rotary control, SC is
displayed. An automatic station search is started. The first search is performed
on an insensitive plane, all further searches on a sensitive plane. Receivable
stations can be heard for 8 seconds. Press the right rotary control if the received
program should be retained.
Direct frequency input
Select radio menu mode and then, within 8 seconds, enter the frequency using
the multifunction buttons.
11
USEnglisch.bk : RUNDFUNK.fm Seite 12 Freitag, Februar 1, 2002 10:33 AM
Radio Operation
Program type display/search (PTY)
Select radio menu mode and then and press multifunction button “PT”. The
selected station program type is displayed for 10 seconds (e.g. SOFT RCK =
soft rock). If the selected station has no PTY characteristic (see also page 28)
NO PTY appears.
In order to activate search, select radio menu mode and then and press
multifunction button “PT”. Pre-select the desired PTY code using the
multifunction button “ ” or “ ”. Turn the right rotary control within the next
10 seconds. PTY-SEEK is displayed. The previous program is selected if no
station with the selected PTY code is receivable. The unit switches to station
button plane if there is no further actuation within 10 seconds.
FM 1/FM 2 station - retrieve/store
Store: 10 frequencies or programs can be stored on each of wavebands FM 1
and FM 2.
Press multifunction button for 2 - 4 seconds in order to store the desired station
or program.
Retrieve: Press multifunction button “1 - 0”. The stored station is requested.
The frequency is displayed if the station cannot be identified.
12
USEnglisch.bk : RUNDFUNK.fm Seite 13 Freitag, Februar 1, 2002 10:33 AM
Radio Operation
AM station - retrieve/store
Retrieve: Press multifunction button “1 - 0”. The stored station is requested.
Store: 10 stations can be stored under station buttons. Search for the desired
station and press the multifunction button until the station button number is
displayed.
AM / FM autostore
Select desired waveband. Select radio menu mode. Then press multifunction
button “AS” repeatedly until AS-SEEK is displayed. The 10 stations with the
best reception are stored under the station buttons in order of quality. The
autostore plane is identified on the display by AS.
Select radio menu mode in order to quit the autostore storage plane.
Then press multifunction button “AS”. The radio switches back to the station
button plane
Manual tuning
Select radio menu mode and then turn the right rotary control.
Tuning steps of 200 kHz (FM) or 10 kHz (AM) are performed.
Pressing the right rotary control switches to fine tuning (1kHz steps) for AM.
The function is quit if there is no further actuation within 10 seconds.
13
USEnglisch.bk : RUNDFUNK.fm Seite 14 Freitag, Februar 1, 2002 10:33 AM
Radio Operation
Traffic Program (TP)
The traffic program system offers the advantage that current traffic news can
be received and heard despite the fact that Tape or CD/MDC are selected. For
this purpose, it is essential that a traffic program station is selected in the FM
waveband and that the traffic program is activated.
Traffic program station - display / select
If a traffic program station is selected, the abbreviation T appears.
Press the button and a station search will begin to locate the next station
broadcasting the TP identifier.
The station can also be selected by station search or by direct frequency entry.
Announcement standby - switch on/off
If the selected traffic program station should interrupt the tape, CD/MDC
operation for traffic announcements, the
abbreviation TP is displayed.
button must be pressed until the
If traffic announcements are not desired, the
the abbreviation T appears.
button must be pressed until
Note :
During the traffic announcement, the desired increase in volume
can be set via the volume button. An announcement which is
currently being heard can be terminated by pressing the
button.
The unit then immediately switches back to the previously selected
operating mode. However, the next traffic announcement is
connected through again.
14
USEnglisch.bk : RUNDFUNK.fm Seite 15 Freitag, Februar 1, 2002 10:33 AM
Radio Operation
Telephone mute function
The telephone characteristics can be set in the user menu (see also page 25) if
a telephone system is installed in the vehicle and the mute function lead for the
car telephone is connected to the car radio.
For the setting PH OFF, the radio is switched to mute if a call is received.
For the setting PH ON, the telephone sound is connected through the radio unit
if a call is received.
However, this is only possible if, in addition to the telephone, a handsfree unit
with loudspeaker output is installed and connected to the radio. In both cases,
PHONE is displayed.
Time request
Select radio menu mode in FM waveband. Then press multifunction button
“T”. The current time in hours and minutes is displayed. This display is only
possible if the time signal is received via RBDS. If no time signal has been
received, --:-- is displayed.
15
USEnglisch.bk : CC.fm Seite 16 Freitag, Februar 1, 2002 10:33 AM
Tape Operation
Cassettes - insert / eject
Press button briefly; the display folds downwards and the cassette slot
becomes visible. Push in cassette with tape-side to the right until it engages and
press lightly. The cassette is pulled in automatically. Then fold the display up
again.
The unit switches automatically to cassette operation. TAPE and TRACK 1
are displayed.
If there is already a cassette in the cassette slot, press
until TAPE appears on the display.
button repeatedly
In order to eject a cassette, press
button briefly; the display folds
downwards and the cassette is ejected and can be removed. Then fold the
display up again.
Note :
The cassette is not ejected when the unit is switched off but
remains in the cassette slot.
Track switching
The track is changed automatically at the end of the tape.
The tape track can be switched at any desired position by pressing briefly one
of the multifunction buttons for track switching. The track currently playing is
shown on the display.
Radio operation during forward / rewind
During forward / rewind, the radio (FM) can be switched through by turning
the volume control. Operation of the radio functions is, however, not possible.
16
USEnglisch.bk : CC.fm Seite 17 Freitag, Februar 1, 2002 10:33 AM
Tape Operaiton
Fast forward / rewind
During cassette operation, fast forward / rewind can be activated using the
multifunction buttons.
In order to cancel the function, press or turn the right rotary control, or press
the track switching buttons or the fast forward / rewind buttons.
Music search - forwards / backwards
In order to activate the forward music search, turn the right rotary control to the
right until the desired number of tracks to be skipped (max. 9) is set.
In order to activate the backward music search, turn the right rotary control to
the left until the desired number of tracks to be skipped (max. 9) is set.
The beginning of a track can only be found if there is a pause of at least 4
seconds between tracks. In order to cancel the function, press or turn the right
rotary control, or press the track switching buttons or the fast forward / rewind
buttons.
Dolby NR
For the playing of cassettes which have been recorded using Dolby NR, press
the multifunction button repeatedly until the desired noise reduction mode
(Dolby B or Dolby C) appears on the display.
For the playing of non-Dolby cassettes, press the button repeatedly until the
Dolby NR display is extinguished.
17
USEnglisch.bk : CC.fm Seite 18 Freitag, Februar 1, 2002 10:33 AM
Tape Operation
Skip blank
If skip blank is active, automatic forward is activated at blank tape sections
which are longer than 10 to 15 seconds.
In order to activate the function, press the multifunction button “SB” until SB
is shown on the display.
Scan - search
Press the right rotary control to start the scan search.
SC appears on the display. Each track is played for approx. 10 seconds.
In order to cancel the function, press the track switching buttons or the fast
forward / rewind buttons.
Cleaning the cassette mechanism
After a time, the reproduction quality of cassettes is reduced due to
unavoidable dirt and dust deposits on the sound head. The drive components in
the cassette mechanism also become soiled. For this reason the cassette
mechanism should be cleaned from time to time. The prompt CLEAN appears
on the display after each 30 hours' running time.
Use a cleaning cassette suitable for reverse operation for this purpose. The
cleaning cassette should be removed again after 30 seconds.
18
USEnglisch.bk : CD.fm Seite 19 Freitag, Februar 1, 2002 10:33 AM
CD/MD Changer Operation
Compact Disc (CD) instructions
Sound interruptions may occur if the CD is soiled. In order to ensure optimum
tone quality, please note the following:
-
Always touch the CD at the edges only. Keep the CD clean and never touch
the surface.
Never stick anything on the CD.
Correct
Incorrect
Correct
-
-
Protect the CDs against direct sunlight and from heat sources such as
heaters, etc.
-
Before playing, clean the CD with a commercially available cleaning cloth,
wiping from the center outwards. Solvents such as petrol, thinners and
other commercially available cleaners and antistatic sprays must not be
used.
Incorrect
Operational readiness of CD/MD changer
If a CD/MD changer is connected to the car radio, this is ready for operation as
soon as it has been loaded with the filled CD magazine or with MDs. Close the
sliding cover after loading. Further operation is performed via the car radio
control panel.
19
USEnglisch.bk : CD.fm Seite 20 Freitag, Februar 1, 2002 10:33 AM
CD/MD Changer Operation
CD magazine - load / unload
In order to remove the CD magazine, open the sliding cover on the changer and
press the eject button. The magazine is ejected and can be removed.
When inserting CDs in the magazine, please note imprint on magazine.
Note :
Note :
Incorrectly inserted CDs will not be played.
In order to ensure the fastest possible CD change, the magazine
should be fully loaded from compartment 1.
Playing CD/MDs
Press
button repeatedly until the CD/MD changer operation is switched
on. The last CD/MD which was being played, is played from the position in
which it was left before switching off.
The desired CD/MD can be selected via the multifunction buttons “1 - 6”.
During the selection time CD X LOADING or MD X LOADING is
displayed. Subsequently, the magazine compartment number and the number
of the current track for the selected CD/MD are displayed.
If no CD/MD is present in the selected magazine compartment (e.g.
compartment 2), NO CD 2 or NO MD 2 appears briefly on the display.
After playing the last track of a CD/MD, the next CD/MD in the magazine is
automatically selected and played.
20
USEnglisch.bk : CD.fm Seite 21 Freitag, Februar 1, 2002 10:33 AM
CD/MD Changer Operation
Track skip - forwards / reverse
Turn right rotary control to right / left.
If the track has been playing for longer than 10 seconds when the return
function is triggered, a return to the beginning of the track takes place.
Through further turning of the right rotary control, several tracks can be
skipped over in forward or reverse directions. Skip returns to the first track
when the last track has been reached. Analogously, it jumps from the first to
the last track.
Scan search
Press and hold the right rotary control, until the prompt SC appears on the
display. All following CD tracks are played for 8 seconds each. Press the rotary
control again to terminate the scan search.
Fast forward / rewind
Press
button after which fast forward (audible) is activated by pressing the
multifunction button “
the multifunction button “
function.
” and fast rewind (audible) is activated by pressing
”. The relative time is displayed during this
Fast forward / rewind is terminated by releasing the multifunction button. The
relative time is displayed for a further 8 seconds.
21
USEnglisch.bk : CD.fm Seite 22 Freitag, Februar 1, 2002 10:33 AM
CD/MD Changer Operation
Relative time, number of tracks, total playing time
Press
button after which by pressing the multifunction button “T”, the
relative time for the track currently being played is displayed for approx. 10
seconds.
By again pressing the multifunction button “T” (within 10 seconds), the
number of tracks and total playing time of the CD currently being played are
displayed for approx. 10 seconds.
Random play
Press
button after which the random play is activated by pressing the
multifunction button “RP”. The tracks of the current CD are then played in
random order. The abbreviation RP appears on the display.
The random play function is terminated by repeated pressing of the
multifunction button “RP”.
Direct track selection
Press button after which the unit is switched to select mode by pressing the
multifunction button “0”.
The digits 1 - 0 and TRACK _ _ are displayed.
A track can be selected directly by using the multifunction buttons “1-0”. The
unit switches back to CD menu mode if no buttons are actuated for approx. 8
seconds.
22
USEnglisch.bk : USER.fm Seite 23 Freitag, Februar 1, 2002 10:33 AM
User Menu
User menu - request / quit
After requesting the user menu, the following basic settings can be entered
according to your personal preference.
USER
-
-
-
-
-
-
user memory
search mode
SEEK
GAL
speed dependent volume control
LHD / RHD setting
telephone characteristics
viewing angle setting
country setting
DRIVER
PHONE
ANGLE
COUNTRY -
END
-
quit user menu
The user menu is requested by pressing the
button for longer than 8
seconds. SEL USER appears on the display. Further actuation must take place
within 4 seconds, otherwise the user menu is quit automatically.
In order to quit the user menu, set END using the right rotary control. The user
menu is quit after 4 seconds.
DRIVER setting
If a telephone system with handsfree unit is installed the telephone
conversation is conducted via one loudspeaker side. The relevant loudspeaker
side (LHD / RHD) is selected using the DRIVER setting.
For selection, request user menu. Then set DRIVER using the right rotary
control. Using the multifunction buttons “ ” or “ ” select between DRV L
(LHD) and DRV R (RHD). The setting is stored automatically.
23
USEnglisch.bk : USER.fm Seite 24 Freitag, Februar 1, 2002 10:33 AM
User Menu
User memory
Request user menu, then set USER using the right rotary control. Using the
multifunction buttons “ ” or “ ” a choice of three different users is available.
Both tone settings and the last selected station as the unit was switched off are
stored in each user memory.
LED setting
The flashing of the LED (flashes when unit is switched off) can be switched on
or off using this function.
Request user menu, then set LED using the right rotary control. Pressing the
multifunction buttons “ ” or “ ” enables a choice between LED ON and LED
OFF.
GAL setting
The GAL is a car radio control circuit which automatically adjusts the car radio
volume according to vehicle speed. This results in compensation of the driving
noise produced at higher speeds.
Request user menu, then set GAL using the right rotary control. Pressing the
multifunction buttons “ ” or “ ” enables a choice between GAL OFF and
GAL 7. With the GAL setting, the amount of volume control can be specified
according to vehicle speed.
The setting is stored automatically.
Explanation of terms:
00
01
07
-
-
-
no volume control
minimal volume adjustment
maximal volume adjustment
24
USEnglisch.bk : USER.fm Seite 25 Freitag, Februar 1, 2002 10:33 AM
User Menu
Telephone mute characteristics (PHONE)
If a telephone system with handsfree unit is installed in the vehicle, the
telephone conversation can be conducted via the car radio system. Thus,
installation of the normally required additional loudspeaker is not necessary.
However, the signal cables (AF - telephone input and earth - telephone input)
must be connected to the car radio (see page 29).
In order to activate, request user menu then set PHONE using the right rotary
control. Then, the multifunction buttons “ ” or “ ” can be used to select
between
PH OFF
PH ON
-
-
telephone mute function and
telephone conversation via car radio.
are selected. The setting is effective immediately after actuating the
multifunction button.
Viewing angle setting (ANGLE)
Request user menu, then set ANGLE using the right rotary control. Using the
multifunction buttons “ ” or “ ” enables a choice between four different
viewing angle settings (VIEW 1-4) for the display. The setting is effective
immediately after actuating the multifunction button.
25
USEnglisch.bk : USER.fm Seite 26 Freitag, Februar 1, 2002 10:33 AM
User Menu
Country setting (COUNTRY)
Various countries can be set using this function, i.e. the search steps or the
received waveband are changed according to the selected setting.
Request user menu, then set COUNTRY using the right rotary control. Choose
one of the settings listed below using the multifunction buttons “ ” or “ ”.
The setting is stored automatically.
Possible settings are:
USA
for the USA
S-AMERIC for South America
AUSTRALI for Australia
ASIA
for Asia
The band limits and search steps are listed on page 29. For the ASIA setting the
SW (short wave) wave band is additionally activated.
26
USEnglisch.bk : Anschluss.fm Seite 27 Freitag, Februar 1, 2002 10:33 AM
Connection Instructions
C3
C2
C1
B
A
Socket A
Socket C1
1
2
3
4
5
6
7
8
Speed-dependent volume control
not assigned
Telephone mute / clearing function
Permanent positive (terminal 30)
Control output for automatic aerial / amplifier
not assigned
1
2
3
4
5
6
LineOut rear left
LineOut rear right
AF earth
LineOut front links
LineOut front right
not assigned
Switched positive (terminal 15)
Earth (terminal 31)
Socket C2
7-12 Special connection for Becker CD changer /
Sony MD changer
Socket B
1
2
3
4
5
6
7
8
Loudspeaker rear right +
Loudspeaker rear right -
Loudspeaker front right +
Loudspeaker front right -
Loudspeaker front left +
Loudspeaker front left -
Loudspeaker rear left +
Loudspeaker rear left -
Socket C3
13 AF telephone input
14 Earth - telephone input
15-20 Special connection for Becker CD changer /
Sony MD changer
27
USEnglisch.bk : Erläuterung.fm Seite 28 Freitag, Februar 1, 2002 10:33 AM
General Instructions
RBDS system
This car radio is capable of receiving RBDS signals (RBDS = Radio -
Broadcasting - Data - System) in the FM range. RBDS is a technique which
enables the transmission of inaudible additional information in the FM
broadcasting range. This means that the transmitter broadcasts information
which can be evaluated by the car radio.
PTY (Program Type)
Specific types of programme, such as e.g. sport, pop music, classical music
etc., can be selected using the PTY function.
The PTY is broadcast by the RBDS transmitter, provided that the transmitter is
equipped with this function. The selected transmitter programme type can be
displayed or a search of a specific PTY transmitter can be performed.
Examples of programme types are:
NEWS
News service
Information programs
sports reports
Talk
SOFT
NOSTALGANostalgia
JAZZ Jazz
CLASSICL Classical
R&B R&B
Soft
INFORM
SPORTS
TALK
ROCK
Rock
CLS ROCK Classic rock
ADLT HIT Adult hits
SOFT RCK Soft rock
SOFT R&B Soft R&B
LANGUAGELanguage
REL MUSC Religious music
REL TALK Religious talk
PERSNLTY Personality
TOP 40
COUNTRY Country
OLDIES Oldies
WEATHER Weather forecast
NO PTY No programme type
Top 40
PUBLIC Public
PTY 24-28 not specified
28
USEnglisch.bk : TECHDAT.fm Seite 29 Freitag, Februar 1, 2002 10:33 AM
Technical Data
Wavebands
:
FM 87.9 MHz - 107.9 MHz (USA); FM 87.5 MHz - 107.9 MHz (S-AMERIC, AUSTRALI)
FM 87.5 MHz - 108 MHz (ASIA)
AM 530 kHz - 1700 kHz (USA, S-AMERIC); AM 531 kHz - 1602 kHz (AUSTRALI, ASIA)
for ASIA additionally SW with 5900 kHz - 6250 kHz
Search steps
FM: 200 kHz (USA, S-AMERIC); 100 kHz (S-AMERIC); 50 kHz (ASIA)
AM: 10 kHz (USA, S-AMERIC); 9 kHz (S-AMERIC, ASIA)
SW: 5 kHz (ASIA)
Frequency range
:
50 Hz - 14 kHz for cassette operation
20 Hz - 20 kHz for CD/MD operation
30 Hz - 15 kHz for FM
50 Hz - 2.5 kHz for AM
Output power
:
:
4 x 18 Watt
Line cross-section
min. 0.75 mm²
Loudspeaker impedance: min. 4 9
Line out
:
:
:
:
:
:
:
4 x analogue line out (Va max 3Veff at 10 k9)
GAL
For speed dependent volume control, the adjustment is performed in 8 - 19 steps of 1.25 dB.
Aerial
Impedance 50 9
Max. input voltage 8 V
Low active level < 2 Volt
12 Volt
AF telephone input
Telephone mute
Supply voltage
CD/MD connection
The Becker CD changer Silverstone (2660 or 2630), or the Sony MD changers MDX 60 and
MDX 61 can be connected.
Playable CDs
:
Only CDs which conform to DIN EN 60908 may be used.
The use of 8 cm CDs with adapter is not recommended.
29
|