FieldServer Computer Drive FS 8700 17 User Manual

A Sierra Monitor Company  
Driver Manual  
(Supplement to the FieldServer Instruction Manual)  
FS-8700-17 Optomux  
APPLICABILITY & EFFECTIVITY  
Effective for all systems manufactured after January 1, 1999  
Instruction Manual Part Number FS-8700-01  
2/18/2004  
Rev: 1.2  
 
FS-8700-17 Optomux  
Driver Manual  
1 Optomux Driver Description  
The Optomux Driver allows the FieldServer to transfer data to and from devices over either  
RS-232 or RS-485 using the Optomux Driver protocol.  
The Optomux driver is a client only driver. This means that the driver can poll an  
Optomux protocol compliant device but cannot emulate one.  
The Optomux protocol provides a large command set. Many of the commands are used for  
OPTO22 device configuration. This driver supports the full command set and thus the  
driver may be used to configure as well as to poll OPTO22 devices.  
1.1 Operating Methods  
The Optomux driver provides three methods of operation. Users may use any  
combination of methods.  
Static Operation  
If the hardware configuration is fixed and known then this is a suitable method. The  
devices to be polled / commanded are configured using the FieldServer CSV file.  
Dynamic Operation  
If the hardware configuration may change or if hardware settings may change  
dynamically or (more realistically) if you wish to change some aspect of the hardware  
configuration such as a delay time or reset a latch without changing the CSV file and  
resetting the FieldServer then this operating method is suitable. The commands set can  
be configured by changing the values in the FieldServer’s data arrays. This operating  
mode may be considered a data driven one.  
Triggered Operation  
This operating mode allows commands to be triggered by changing the value in the  
FieldServer’s data arrays. This operating mode is useful if requiring an action triggered  
by a remote device.  
1.2 Statistics and Command Reponses  
All FieldServer drivers report communication statistics that allow the operation of the  
driver to be monitored.  
In addition to the standard statistics, this driver exposes the communication statistics for  
each port by presenting them in a user specified data array where they can be monitored  
by a remote device or HMI system.  
The Optomux driver also exposes the response status to each poll and command (if  
required) by writing the response statuses to a user specified data array. This useful  
feature allows remote devices to check whether a command has been completed  
successfully.  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 1  
 
FS-8700-17 Optomux  
Driver Manual  
2 Driver Scope of Supply  
2.1 Supplied by FieldServer Technologies for this driver  
Driver Manual.  
2.2 Provided by user  
Optomux System  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 2  
 
FS-8700-17 Optomux  
Driver Manual  
3 Hardware Connections  
The FieldServer is connected to the OPTO22 device as shown below.  
Configure the OPTO22 device according to manufacturer’s instructions.  
COM  
COM  
COM  
- + - + - + - +  
- + - + - + - +  
- + - + - + - +  
FO FH TH TO * *  
FO FH TH TO  
FO FH TH TO  
PREVIOUS OPTOMUX *  
B1 OR B2  
NEXT OPTOMUX *  
B1 OR B2  
AC30A/B  
*
B2 COMMUNICATION CONNECTIONS ARE MADE TO THE RACK (PB4AH, PA8AH OR  
PB16AH), NOT TO THE BRAIN BOARD.  
** DO NOT CONNECT ANY "COM" POINT TO EARTH GROUND.  
FS-X40  
Power  
Net  
1
Net  
2
P8  
P7  
P6  
P5  
P4  
P3  
P2  
P1  
RS 232  
Et her n et  
10 Base T  
R2  
RS 485  
(Opto - Isolated)  
R1  
GROUND  
DTR  
5
6
7
8
1
2
3
4
Rx  
CTS  
8
1
RTS  
DSR  
Tx  
GROUND  
DC AUX Power  
R2  
R1  
RS 485  
(Opto - Isolated)  
(408)-262-2299  
FIELDSERVER - OPTO22  
CONNECTION DIAGRAM  
BASE NAME:  
FILE NAME: T28700-17.VSD  
DATE: 6/27/01  
BY: MN  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 3  
 
FS-8700-17 Optomux  
Driver Manual  
4 Configuring the FieldServer as a Optomux Driver Client  
For a detailed discussion on FieldServer configuration, please refer to the FieldServer  
Configuration Manual. The information that follows describes how to expand upon the  
factory defaults provided in the configuration files included with the FieldServer (See “.csv”  
files on the driver diskette).  
This section documents and describes the parameters necessary for configuring the  
FieldServer to communicate with an Optomux Device.  
The configuration file tells the FieldServer about its interfaces, and the routing of data  
required. In order to enable the FieldServer for Optomux Driver communications, the driver  
independent FieldServer buffers need to be declared in the “Data Arrays” section, the  
destination device addresses need to be declared in the “Client Side Nodes” section, and  
the data required from the servers needs to be mapped in the “Client Side Map  
Descriptors” section. Details on how to do this can be found below.  
Note that in the tables, * indicates an optional parameter, with the bold legal value being  
the default.  
4.1 Data Arrays  
Section Title  
Data_Arrays  
Column Title  
Data_Array_Name  
Function  
Provide name for Data Array  
Legal Values  
Up to 15 alphanumeric  
characters  
Data_Format  
Provide data format. Each data array can FLOAT, BIT, UInt16, SInt16,  
only take on one format.  
Packed_Bit, Byte,  
Packed_Byte,  
Swapped_Byte  
1-10,000  
Data_Array_Length  
Number of Data Objects. Must be larger  
than the data storage area required for  
the data being placed in this array.  
Example  
//  
Data Arrays  
//  
Data_Arrays  
Data_Array_Name,  
DA_AI_01,  
DA_AO_01,  
DA_DI_01,  
DA_DO_01,  
Data_Format,  
UInt16,  
UInt16,  
Bit,  
Data_Array_Length  
200  
200  
200  
200  
Bit,  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 4  
 
FS-8700-17 Optomux  
Driver Manual  
Legal Values  
4.2 Client Side Connections  
Section Title  
Connections  
Column Title  
Port  
Function  
Specify which port the device is R1-R2, (FS-X40 Series)  
connected to the FieldServer  
Specify baud rate  
R1 (FS-X20 Series)  
110 – 115200, standard baud  
rates only  
Baud*  
At the time of publication of this  
manual the OPTO22 device’s  
support standard baud Rates in  
the range 300-38400.  
Parity*  
Data_Bits*  
Specify parity  
Specify data bits  
Even, Odd, None, Mark, Space  
7, 8  
Stop_Bits*  
Protocol  
Specify stop bits  
1
Specify protocol used  
Optomux  
Handshaking*  
Poll Delay*  
Specify hardware handshaking  
Time between internal polls  
RTS, RTS/CTS, None  
0-32000 seconds  
default 1 second  
Example  
//  
Client Side Connections  
Connections  
Port, Baud, Parity, Protocol, Handshaking, Poll_Delay  
R1, 9600, None, Opto22 , None , 0.100s  
4.3 Client Side Nodes  
Section Title  
Nodes  
Column Title  
Function  
Legal Values  
Node_Name  
Provide name for node  
Up to 32 alphanumeric  
characters  
Node_ID  
Protocol  
Port  
OPTO22 device address.  
Specify protocol used  
Specify which port the device is R1-R2, (P1-P8 with a  
connected to the FieldServer converter)  
0-255  
Optomux  
Example  
//  
Client Side Nodes  
Nodes  
Node_Name, Node_ID, Protocol, Port  
Optomux1 , 1 , Optomux , R1  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 5  
 
FS-8700-17 Optomux  
Driver Manual  
4.4 Client Side Map Descriptors  
4.4.1 FieldServer Related Map Descriptor Parameters  
Column Title  
Function  
Legal Values  
Up to 32 alphanumeric  
characters  
Map_Descriptor_Name Name of this Map Descriptor  
Data_Array_Name  
Name of Data Array where data is to be  
stored / retrieved in the FieldServer.  
One of the Data Array names  
from “Data Array” section above  
The use of this array is dependent on  
the Optomux command used in the map  
descriptor.  
For example some commands use one  
data value for all module positions to be  
affected by the command (Driver will  
only use one data array element). Other  
commands may use one data element  
per module position specified. In this  
case the FieldServer may use up to 16  
data array elements.  
To fully understand this, read the notes  
in chapter 6.  
Da_Bit_Name*  
This parameter is only required for  
dynamic module position specification.  
Ie. You intend using a data array to tell  
the driver which module positions to  
affect by a command. In this case use  
this parameter. Up to 16 elements will  
be inspected. The first element will  
always be used for the first module  
position , the 2nd element for the 2nd  
module position ….  
One of the Data Array names  
from “Data Array” section above  
Module positions are specified by setting  
the corresponding array element to a  
non-zero value. Module positions are left  
unspecified by setting the module array  
position to zero.  
The first element of this array that is  
used is determined by the  
Data_Array_Offset parameter.  
Additional information is provided in  
chapter 6.  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 6  
 
FS-8700-17 Optomux  
Driver Manual  
Da_Byte_Name*  
Names a data array that the driver will  
use to store poll/query response status  
data.  
One of the Data Array names  
from “Data Array” section above  
One data element is used per map  
descriptor. The element is determined  
by the Data_Array_Offset parameter.  
Starting location in Data Array  
Data_Array_Offset  
Function  
0 to maximum specified in “Data  
Array” section above  
RDBC, WRBC, WRBX  
Function of Client Map Descriptor  
4.4.2 Driver Related Map Descriptor Parameters  
Column Title  
Node_Name  
Function  
Name of Node to fetch data  
from  
Legal Values  
One of the node names  
specified in “Client Node  
Descriptor” above  
1..16  
Address*  
Length  
This field is only required if the  
address/length method of  
module position specification is  
used.  
Indicating 1st to 16th module  
position.  
Length of Map Descriptor  
1 - 1000  
Only some commands / queries  
use the value of this map  
descriptor parameter. This is  
indicated in a table provide in  
chapter 6.  
For those commands and  
queries that do use the Length  
parameter the driver never uses  
more than 16 elements of data  
even if the length is set to a  
larger number.  
Although this driver does not  
use the length parameter for  
some commands the  
FieldServer kernel does use  
this parameter to ensure that no  
more than one client map  
descriptor has control of a  
range of array data elements.  
For this reason it is best to  
always specify the length – in  
these cases set it to 1.  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 7  
 
FS-8700-17 Optomux  
Driver Manual  
Opto22_trigger*  
An optional parameter. If used then set the No, Yes  
value of this parameter to yes or no and  
the da_byte_name parameter must be  
specified too.  
When this parameter is set to yes then the  
Optomux driver processes this map  
descriptor differently from a normal wrbc or  
rdbc function.  
The driver processes the map descriptor at  
the scan interval specified. Each time that  
it is processed the driver checks the  
element of the da_byte_name data array  
specified. If the value of the 1st element of  
array located at data_array_offset is 1 then  
the driver executes the command. If the  
value is not equal to one then the driver  
ignores the map descriptor.  
If the map descriptor is triggered then the  
driver will write a response status to the  
same data element on completion of the  
poll. Thus the value of 1 will be set to zero  
for success or some other value indicating  
an error.  
More information is provided in chapter 6.  
This parameter only has meaning when  
the function is a read of digital data.  
Opto22_format*  
Bit, Packed  
By default the OPTO22 devices returns 16  
position states when digital data is read (  
eg. READ STATUS). The Optomux driver  
writes the data as one 16 bit unsigned  
integer to one data element of the data  
array specified. (That is, the data is written  
to the data array in packed bit format.)  
For example, if the 1st and 5th inputs were  
on and all others were off the driver would  
write the value 17 to the first element of the  
data array.  
The driver can be instructed to unpack this  
data into separate bit states, writing each  
module position’s state to a consecutive  
data array element.  
When the Bit keyword is used the driver  
sets the states of consecutive data array  
elements starting at Data_Array_Offset.  
The number of elements that are written is  
determined by length and a maximum of  
16 elements will be written.  
Opto22_function  
This parameter is specified by using one of See Table 6.1  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 8  
 
FS-8700-17 Optomux  
Driver Manual  
the functions provided in table 6.1.  
The parameter must be spelled and  
spaced exactly as provided in the table.  
Leading and trailing spaces are not  
important but inter-word spaces are very  
important. Take care not to use tabs.  
A few Opto22_Functions require one ore  
more additional arguments.  
Opto22_modifier1*  
See Chapter 6.  
SET TIME DELAY  
GENERATE N PULSES  
READ AND AVERAGE INPUTS  
Additional information in chapter 6 will  
indicate the types of values that may be  
assigned to this parameter.  
Opto22_modifier2*  
Opto22_mask*  
See Opto_modifier1  
The mask specifies the positions (1-16) of  
a module that will be affected by a  
command.  
0-65535  
or  
The positions can be specified dynamically 0x0000 – 0xffff  
using a data array or statically by using this  
parameter.  
When this parameter is used and its value  
is non zero then the driver does not  
consider the data contained in the position  
defining array even if it is also defined.  
The value of the mask may be specified in  
hexadecimal or in decimal.  
To specify a number in hexadecimal the  
number must be prefixed with 0x and have  
a maximum of 4 digits.  
Examples.  
Decimal: 257 -> Indicates the 1st and 9th  
positions.  
Hexadecimal: 0x0101 -> indicates the 1st  
and 9th positions.  
4.4.3 Timing Parameters  
Column Title  
Function  
Legal Values  
Scan_Interval  
Rate at which data is polled  
>0.1s  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 9  
 
FS-8700-17 Optomux  
Driver Manual  
4.4.4 Map Descriptor Example 1 – Read on/off Status  
In this example the on/off status of all module positions of the Optomux device are read and stored. They are read continuously (rdbc) every 5 seconds  
(Scan_Interval). The Read Status command returns one packed 16 bit value. There is one bit per module position, thus, if the returned value was 2 then this would  
indicate that the 2nd position is on and all other positions are off.  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, node_name, Length, Scan_Interval, opto22_function ,  
DEVICE77_STAT , DISC_INPUTS , 0  
, rdbc , DEV77 , 1  
, 5.0s  
, READ STATUS ,  
Map descriptor  
names are often  
used in error  
messages so it may  
be helpful to have  
unique names.  
This is the name of  
The device will  
be read  
continuously.  
This is the name  
of the node. The  
node must have  
previously been  
defined in the  
Nodes section  
of the CSV file.  
Its Node_ID  
Only one  
element of the  
data array is  
reserved for this  
map descriptor.  
This is the name  
of the Optomux  
command /  
query that must  
be performed.  
the data array in  
which the data will  
be stored.  
Ensure that the  
Data_Format of the  
array is suitable for  
storing the data  
returned by the  
device.  
The data will be  
stored at offset  
zero (First  
element) of the  
data array.  
It must be  
spelled and  
spaced exactly  
as in table 6.1  
Dashes, spaces,  
upper and lowercase  
characters may be  
used.  
should be set to  
77 to reference  
the device  
addressed as 77.  
Chapter 6 provides  
details of the type of  
data returned by  
each command.  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 10  
 
FS-8700-17 Optomux  
Driver Manual  
4.4.5 Map Descriptor Example 2 – Read On/Off Status (Data stored differently)  
This example reads the same data as the previous example. The difference is that the data is stored differently. In this example the data is  
unpacked and stored in 16 consecutive data array elements – one element per module position.  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, node_name, Length, Scan_Interval, opto22_function , opto22_format  
DEVICE77_STAT , DISC_INPUTS , 0  
, rdbc , DEV77 , 16  
, 5.0s  
, READ STATUS , Bit  
This is how the  
driver is instructed  
to unpack the digital  
data.  
The length has  
changed to 16 to  
reserve 16 data array  
elements for this  
map descriptor.  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 11  
 
FS-8700-17 Optomux  
Driver Manual  
4.4.6 Map Descriptor Example 3 – Command Response/Completion Status  
We use example 1 to show how it can be modified to get the driver to expose the response / status generated when the command was executed.  
The response / status values indicate the success / failure of the command based either on the driver’s ability to complete the command OR on  
the ack/nack returned by the device.  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, node_name, Length, Scan_Interval, opto22_function , DA_Byte_Name  
DEVICE77_STAT , DISC_INPUTS , 0  
, rdbc , DEV77 , 1  
, 5.0s  
, READ STATUS, RESPONSE_ARR  
By virtue of defining the DA_Byte_Name parameter the  
driver will now store a response status each time the poll is  
executed.  
The response / status code will be stored in the data array  
called REPONSE_ARR. One element of the array located  
at Data_Array_Offset will be used. The data array’s data  
format should at least be able to store a byte of data as  
response/status codes range from 0-255.  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 12  
 
FS-8700-17 Optomux  
Driver Manual  
4.4.7 Map Descriptor Example 4 – Triggered Action  
This example shows the elements necessary to generate a triggered poll. Even though this map descriptor appears to write to the device  
continuously the driver recognizes the opto22_trigger parameter and based on its value will only send the poll when the trigger value is set.  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_Name, Length, Scan_Interval, opto22_function , opto22_trigger, DA_Byte_Name  
DEVICE77_STAT , CNTR_POSNS , 0  
, wrbc , DEV77 , 16 , 0.2s  
, CLEAR COUNTERS , Yes  
, COMMAND_ARRAY  
This map descriptor  
is processed as a  
write command and  
will be processed  
continuously.  
The Driver will process this  
map descriptor every 0.2  
seconds.  
This keyword value for the  
opto22_trigger parameter  
tells the driver only to send  
this Optomux command if it  
has been triggered.  
This is the name of a data array  
whose contents will be used to  
trigger the command.  
In this example, this does not  
mean that the command will  
be sent to the device every  
0.2 seconds. It does mean  
that the driver will check to  
see if a trigger has been set  
every 0.2 seconds.  
The driver looks at the element  
found at the Data_Array_Offset  
and if that value=1 then the  
command is sent. On  
completion/error the driver will  
change this value to some other  
number.  
When this parameter is used  
the DA_Byte_Name  
parameter must also be used.  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 13  
 
FS-8700-17 Optomux  
Driver Manual  
4.4.8 Map Descriptor Example 5 – Using Address and Length to tell the FieldServer which module positions to access.  
This example shows a map descriptor which reads analog inputs from an Optomux Device. The address and length tell the driver which inputs to  
read. Take care to ensure that the data array used for storage has a data format suitable for storing the data type returned by the command. In  
this case an unsigned integer at least 16 bits long ( eg UINT16 or FLOAT). Also take care to ensure that you understand the scaling of the data  
returned by the Optomux device. There are parameters that you can add to a map descriptor to have the driver scale the value. This is discussed  
in the FieldServer Configuration Manual.  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_Name, Address, Length, Scan_Interval, opto22_function  
DEVICE77_STAT , ANA_DATA , 0  
, rdbc , DEV77 , 2  
, 15 , 1.0s  
, READ ANALOG INPUTS  
Data read from the  
Optomux Device is  
placed in this array.  
The first module  
position that is read  
is position 2.  
Data from 15  
This is the Optomux  
Driver function that  
must be performed.  
module positions  
must be read. Thus  
starting at 2, the last  
module position  
read is 16.  
Module positions  
are numbered 1 to  
16.  
Starting at this array  
position.  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 14  
 
FS-8700-17 Optomux  
Driver Manual  
4.4.9 Map Descriptor Example 6 – Using a Mask to Address specific module positions  
There may be occasions when it is not suitable to use address and length. For example if you are attempting to address non-consecutive  
Optomux module positions OR when you wish to use a command that affects all module positions. The driver provides an alternate method for  
module position specification by allowing you to specify a mask as a parameter in the CSV file. The mask may be specified in decimal or  
hexadecimal format.  
In this example, module positions 1 and 5 are pulsed.  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_Name, Length, Scan_Interval, opto22_mask, opto22_function  
PULSE77  
, TIME_DATA , 0  
, wrbc , DEV77 , 1  
, 10.0s  
, 0x0011  
, START ON PULSE  
This function turned  
on the specified  
module positions for  
a specified period.  
Un specified  
Module positions are specified in hexadecimal  
in this example.  
positions (mask bit  
positions equal zero)  
are non affected by  
the command.  
0x0001 = Module Position 1  
0x0002 = Module Position 2  
0x0003 = Module Positions 1 & 2  
…..  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 15  
 
FS-8700-17 Optomux  
Driver Manual  
4.4.10 Map Descriptor Example 7 – Specifying Module Positions Dynamically  
Previous examples addressed module positions statically. This example illustrates how you can use a data array’s value to specify the module position’s to be  
affected by a command. As data arrays can have their values changed by remote devices, the module position specification may be changed dynamically. The  
CSV file does not require editing. This method can be used all the time or only if you wish to use one of those commands which would typically require dynamic  
addressing.  
In this example, module positions 1 and 5 are pulsed.  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_Name, Length, Scan_Interval, DA_Bit_Name , opto22_function  
CLRLOW77  
, LOW_ARRAY , 0  
, wrbc , DEV77 , 16  
, 10.0s  
, POS_ARR , READ AND CLEAR LOWEST VALUES  
In this example, the driver will store 16 lowest values in an array  
called LOW_ARR starting at position Data_Array_Offset.  
Any number 1 to 16.  
This data array will be used by  
the driver to determine the  
module positions to be affected  
by the command.  
The driver stops at  
16, ignoring larger  
values.  
The driver uses the length  
(max=16) and the  
Data_Array_Offset. The first  
specified element corresponds to  
module position 1. If its value is  
non-zero then the position is  
specified by the driver.  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 16  
 
5 Configuring the FieldServer as a Optomux Server  
The FieldServer does not support the emulation of an Optomux server at present.  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 17  
 
FS-8700-17 Optomux  
Driver Manual  
6 Driver Notes  
6.1 Data_Array_Name, DA_Bit_Name, DA_Byte_Name  
These parameters are used to specify data array names. Despite their  
names a data array of any Data_Format can be used for any of these  
parameters.  
This driver uses DA_Byte_Name exclusively as a location for the commands  
to trigger map descriptors and in which to store poll response status.  
The use of DA_Bit_Name is command sensitive and is used to allow the  
values in a data array to determine the module positions to be affected by a  
command.  
The use of the Data_Array_Name Parameter is typical i.e. Used to store  
data that is read or used as a source for data that is written.  
6.2 Module Positions  
Specify module positions Statically by  
Using Address and Length  
or  
or  
Using the opto22_mask parameter  
Specify module positions dynamically by  
Using the values of a data array (da_bit_array)  
What happens if more than one method is used for module position specification ?  
The driver evaluates the specification in the order listed above. Thus if address &  
length are specified as well as the opto22_mask, the driver will use the address  
and length.  
6.3 Command Response Status  
If a data array is specified using the DA_Byte_Array parameter then the driver  
will store a response status code in the array, updating the value each time a  
command is executed.  
Value  
Description  
0
1
Command completed successfully.  
Used to trigger a command.  
All other values indicate error conditions. For Responses 128 to  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 18  
 
FS-8700-17 Optomux  
Driver Manual  
255 the Optomux literature should be read for additional  
information as these are codes returned by the Optomux device.  
128  
Nak from Optomux Device. Power Up Clear Expected. Command  
Ignored.  
129  
130  
131  
132  
133  
134  
135  
Nak from Optomux Device. Undefined Command  
Nak from Optomux Device. Checksum Error  
Nak from Optomux Device. Input Buffer Overun  
Nak from Optomux Device. Non Printable Ascii character received  
Nak from Optomux Device. Data Field Error  
Nak from Optomux Device. Communication watchdog timeout  
Nak from Optomux Device. Specified limits invalid.  
The following codes are generated by the driver. They all indicate  
errors.  
250  
251  
An ack with no data was expected. Ack with Data was received.  
The driver Complete function returned an error, could be  
checksum, bad 1st char ... ie. The message was badly formatted.  
Driver Timeout  
An ack was received but it was badly formatted  
A nak was received but was badly formatted  
Message was not acknowledged correctly.  
252  
253  
254  
255  
6.4 Optomux Commands  
The following provides a list of commands supported by the driver. The Command  
Name’s provided in the table must be used in providing values for the opto22_function  
parameter. The notes provided only apply when module positions are specified  
dynamically.  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 19  
 
FS-8700-17 Optomux  
Driver Manual  
NOTES  
COMMAND NAME  
OPTO22_FORMAT MASTER LENGTH  
Read/  
OPTION  
CONSIDERED (See  
Notes)  
Write/  
Both  
POWER UP CLEAR  
4
4
4
w
w
w
RESET  
SET TURN-AROUND DELAY  
Uses 1 element of data array. Legal  
values are 0,1,2,3  
Uses 1 element of data array. Legal  
values are 0 to 7  
Uses the 1st element of data array for  
the timer value.  
Uses 1 element of data array. Legal  
values are 0,1  
SET WATCHDOG DELAY  
SET WATCHDOG DELAY (Analog)  
SET PROTOCOL  
4
3
4
4
w
w
w
r
IDENTIFY Optomux TYPE  
Polled data is stored in the 1st  
element of the data array.  
Delay is found in data array.  
SET ENHANCED DIGITAL WATCHDOG  
SET ENHANCED ANALOG WATCHDOG  
3
1
w
w
Uses up to Length (max=16) array  
elements. Module positions specified  
get setup for fail values by using the  
corresponding positions in data array.  
Uses 1 element of data array.  
SET TIMER RESOLUTION  
w
w
SET TEMPERATURE PROBE TYPE  
3
3
Temp probe type is found in first  
element of data array  
Non-zero module positions get set to  
outputs. Zero module positions get  
set to inputs  
CONFIGURE POSITIONS  
w
CONFIGURE AS INPUTS  
CONFIGURE AS OUTPUTS  
3
3
w
w
Only module positions specified get  
affected by command.  
Only module positions specified get  
affected by command.  
READ MODULE CONFIGURATION  
WRITE OUTPUTS  
4
1
r
w
Uses up to Length (max=16) array  
elements. Non-zero elements get  
turned on, zero value elements get  
turned off.  
ACTIVATE OUTPUTS  
DEACTIVATE OUTPUTS  
READ STATUS  
3
3
2
w
w
r
Only module positions specified get  
affected by command.  
Only module positions specified get  
affected by command.  
If format=Bit then length is considered  
during storage as bits are unpacked  
into data array. If format is non equal  
to bit then result is written as a single  
value into one array element.  
1
Retrieved data is stored in data array.  
Always affects all module positions.  
Cannot be limited by length. Length is  
only used when determining which  
module positions are specified as  
non-zero. Non-zero (Specified)  
elements get set on->off, Zero (Non-  
SET LATCH EDGES  
3
w
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 20  
 
FS-8700-17 Optomux  
Driver Manual  
NOTES  
COMMAND NAME  
OPTO22_FORMAT MASTER LENGTH  
Read/  
OPTION  
CONSIDERED (See  
Notes)  
Write/  
Both  
Specified) module positions get set  
off->on  
Only module positions specified get  
affected by command.  
Only module positions specified get  
affected by command.  
If format=Bit then length is considered  
during storage as bits are unpacked  
into data array. If format is non equal  
to bit then result is written as a single  
value into one array element.  
Non-zero (Specified) module  
positions get affected (cleared) by  
command. But all positions get read.  
Read data get stored in data array.  
During storage opto22_format is  
considered. If format=bit then data is  
unpacked and stored otherwise the  
result for all 16 positions is stored as  
one data element.  
SET LATCH OFF TO ON  
3
3
2
w
w
r
SET LATCH ON TO OFF  
READ LATCHES  
1
1
READ AND CLEAR LATCHES  
3,2  
b
CLEAR LATCHES  
3
3
w
w
Only module positions specified get  
affected by command.  
START/STOP COUNTERS  
All positions are affected by  
command. Non-zero (specified)  
module positions start counting, zero  
(unspecified) module positions stop  
counting  
START COUNTERS  
STOP COUNTERS  
READ COUNTERS  
3
3
1
w
w
r
Only module positions specified get  
affected by command.  
Only module positions specified get  
affected by command.  
Data that is read is put into the  
corresponding array elements of the  
data array based on which module  
positions are read.  
READ AND CLEAR COUNTERS  
1
b
Data that is read is put into the  
corresponding array elements of the  
data array based on which module  
positions are read.  
CLEAR COUNTERS  
SET TIME DELAY  
3
3
w
w
Only module positions specified get  
affected by command.  
The Modifier is specified in the CSV  
file with the opto22_modifier1  
parameter. The data (timeout) is  
retrieved from the first element of the  
data array.  
INITIATE SQUARE WAVE  
3
3
3
w
w
w
HIGH RESOLUTION SQUARE WAVE  
RETRIGGER TIME DELAY  
Only module positions specified get  
affected by command.  
Only specified module positions get  
GENERATE N PULSES  
3
w
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 21  
 
FS-8700-17 Optomux  
Driver Manual  
NOTES  
COMMAND NAME  
OPTO22_FORMAT MASTER LENGTH  
Read/  
OPTION  
CONSIDERED (See  
Notes)  
Write/  
Both  
affected. The Modifier (byte 1&2) are  
specified in the CSV file with the  
opto22_modifier1/2 parameters. The  
data (number of pulses) is retrieved  
from the 1st element of the data  
array.  
Only specified module positions get  
affected. The data (period of pulses)  
is retrieved from the 1st element of  
the data array.  
Only specified module positions get  
affected. The data (period of pulses)  
is retrieved from the first element of  
the data array.  
All Module positions are affected by  
this command. Non-zero (Specified)  
module positions triggered by on,  
zero module positions (un-specified)  
elements get triggered by off.  
Only module positions specified get  
affected by command.  
START ON PULSE  
3
3
3
w
w
w
START OFF PULSE  
SET TRIGGER POLARITY  
TRIGGER ON POSITIVE  
3
3
2
w
w
r
TRIGGER ON NEGATIVE  
READ PULSE COMPLETE BITS  
Only module positions specified get  
affected by command.  
1
If format=Bit then length is considered  
during storage as bits are unpacked  
into data array. If format is non equal  
to bit then result is written as a single  
value into one array element.  
Retrieved data is stored in standard  
data array.  
READ DURATION COUNTERS  
3
3
r
Only specified module positions get  
read. Data read gets put in  
corresponding positions of data array.  
Only specified module positions get  
read. Data read gets put in  
READ AND CLEAR DURATION  
COUNTERS  
b
corresponding positions of data array.  
Only module positions specified get  
affected by command.  
Only specified module positions get  
written. Data written gets extracted  
from corresponding positions of data  
array.  
CLEAR DURATION COUNTERS  
WRITE ANALOG OUTPUTS  
3
3
w
w
READ ANALOG OUTPUTS  
3
3
r
Only specified module positions get  
read. Data read gets put in  
corresponding positions of data array.  
Only specified module positions get  
written. Data written gets extracted  
from corresponding positions of data  
array.  
UPDATE ANALOG OUTPUTS  
w
READ ANALOG INPUTS  
3
r
Only specified module positions get  
read. Data read gets put in  
corresponding positions of data array.  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 22  
 
FS-8700-17 Optomux  
Driver Manual  
NOTES  
COMMAND NAME  
OPTO22_FORMAT MASTER LENGTH  
Read/  
OPTION  
CONSIDERED (See  
Notes)  
Write/  
Both  
r
READ AND AVERAGE INPUT  
4
Only one module position may be  
specified. This position is averaged  
and the result is put in the first  
element of the data array The number  
of samples is specified in modifier1 in  
the csv file.  
START INPUT AVERAGING  
3
2
w
r
Only specified module positions get  
affected by command. First element  
in data array is sent as the number of  
sample to average over.  
If format=Bit then length is considered  
during storage as bits are unpacked  
into data array. If format is non equal  
to bit then result is written as a single  
value into one array element.  
Retrieved data is stored in standard  
data array.  
READ AVERAGE COMPLETE BITS  
1
READ INPUT AVERAGE DATA  
READ TEMPERATURE INPUTS  
READ AVERAGE TEMPERATURE INPUTS  
SET INPUT RANGE  
3
3
3
3
r
r
Only specified module positions get  
read. Data read gets put in  
corresponding positions of data array.  
Only specified module positions get  
read. Data read gets put in  
corresponding positions of data array.  
Only specified module positions get  
read. Data read gets put in  
corresponding positions of data array.  
Only specified module positions have  
their range set to the 2 values found  
in the data array. 1st is high limit,  
second is lo limit.  
r
w
READ OUT-OF-RANGE LATCHES  
4
3
r
High limit latches are placed in first  
element of data array. Low limit  
latches are placed in 2nd element of  
data array.  
Only specified module positions get  
read and cleared. Data read gets put  
in corresponding positions of data  
array.  
READ AND CLEAR RANGE LATCHES  
b
CLEAR OUT-OF-RANGE LATCHES  
READ LOWEST VALUES  
4
3
w
r
Only specified module positions get  
read. Data read gets put in  
corresponding positions of data array.  
Only module positions specified get  
affected by command.  
Only specified module positions get  
read and cleared. Data read gets put  
in corresponding positions of data  
array.  
CLEAR LOWEST VALUES  
3
3
w
b
READ AND CLEAR LOWEST VALUES  
READ PEAK VALUES  
CLEAR PEAK VALUES  
3
3
r
Only specified module positions get  
read. Data read gets put in  
corresponding positions of data array.  
w
Only module positions specified get  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 23  
 
FS-8700-17 Optomux  
Driver Manual  
NOTES  
COMMAND NAME  
OPTO22_FORMAT MASTER LENGTH  
Read/  
OPTION  
CONSIDERED (See  
Notes)  
Write/  
Both  
affected by command.  
READ AND CLEAR PEAK  
3
1
1
1
1
1
1
4
b
Only specified module positions get  
read and cleared. Data read gets put  
in corresponding positions of data  
array.  
Only specified module positions get  
calculated and read. Data read gets  
put in corresponding positions of data  
array.  
Only specified module positions get  
written. Data written gets extracted  
from corresponding positions of data  
array.  
Only specified module positions get  
calculated and read. Data read gets  
put in corresponding positions of data  
array.  
Only specified module positions get  
calculated and read. Data read gets  
put in corresponding positions of data  
array.  
Only specified module positions get  
written. Data written gets extracted  
from corresponding positions of data  
array.  
Only specified module positions get  
calculated and read. Data read gets  
put in corresponding positions of data  
array.  
Uses opto22_modifier1/2 from the  
CSV file set waveform rates and  
types. Only specified positions get  
affected. 2 elements of data array  
are used.  
CALCULATE OFFSETS  
r
SET OFFSETS  
w
r
CALCULATE AND SET OFFSETS  
CALCULATE GAIN COEFFICIENTS  
SET GAIN COEFFICIENTS  
CALCULATE AND SET GAIN  
SET OUTPUT WAVEFORM R  
r
w
r
w
IMPROVED OUTPUT WAVEFORMS  
4
w
Uses opto22_modifier1/2 from the  
CSV file set waveform rates and  
types. Only specified positions get  
affected. 3 elements of data array  
are used.  
Notes on how the Length parameter is used in the CSV file.  
1. The length parameter is always considered.  
2. The length parameter is only considered when the keyword Bit is used in the  
opto22_format parameter.  
3. The length is only used using the address/length method to specify module  
positions or when the dynamic method is used to specify module positions.  
4. The length is never considered.  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 24  
 
FS-8700-17 Optomux  
6.5 Driver Stats  
Driver Manual  
In addition to the standard FieldServer communication statistics described in the FieldServer  
User’s Manual the Optomux Driver can also expose some driver statistics by writing data to  
a data array. A special map descriptor is required. The driver recognizes the map  
descriptor by its name which must be "opto22-stats" .  
The following example shows how this special map descriptor can be configured.  
Nodes  
Node_name, Node_ID, Protocol  
null_node,  
0
, Optomux  
Data_Arrays  
Data_Array_Name, Data_Format, Data_Array_Length  
OPTO22_STATS , UINT32  
, 300  
Map_Descriptors  
Map_descriptor_Name, Data_Array_Name, Node_name, length  
Opto22-stats , OPTO22_STATS , null_node , 300  
When the driver sees this map descriptor it uses the data array SK_STATS (in this  
example) to store driver specific statistics. Only one of these map descriptors may be  
specified per FieldServer.  
The driver stores the following data.  
Array Element  
Contents  
OPTO_STAT_BAD_FUNCTION  
0
1
The Opto22_Function has a  
bad value.  
Mask cannot be specified in a  
CSV file with a zero value.  
OPTO_STAT_DYNAMIC_MASK  
2
OPTO_STAT_TIMEOUT  
3
4
OPTO_STAT_STREAMING  
OPTO_STAT_NAK  
5
OPTO_STAT_PROTOCOL  
6
7
8
9
10  
11  
12  
12  
OPTO_STAT_IC_TIMEOUT  
OPTO_STAT_DEVICE_MSG_RECD  
OPTO_STAT_DEVICE_BYTES_RECD  
OPTO_STAT_DEVICE_FUNCTION  
OPTO_STAT_NO_START  
OPTO_STAT_MSG_IGNORED  
OPTO_STAT_POLL_MSG_SENT  
OPTO_STAT_POLL_BYTES_SENT  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 25  
 
FS-8700-17 Optomux  
Driver Manual  
7 Revision History  
Doc.  
Rev.  
Date  
Resp  
Format  
Driver Ver.  
Comment  
2/18/04  
JD  
MF  
0
1
Releasing  
FieldServer Technologies 1991 Tarob Court, Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042  
Page 26  
 

Eclipse Fujitsu Ten GPS Receiver CD2030 User Manual
EverFocus DVR EDVR16D3 User Manual
Fellowes Laminator Titan A3 User Manual
Fisher Price Doll X7759 User Manual
Furuno Marine RADAR FR 1510D User Manual
Gateway Laptop ID5821U User Manual
Gefen Switch 4x4 DVI Matrix User Manual
GE Personal Computer GFK 2251 User Manual
Gianni Industries Door EB 220 32 User Manual
G Technology Portable Media Storage 0G02229 User Manual