Fujitsu Network Card LQFP 64P User Manual

FUJITSU SEMICONDUCTOR  
SUPPORT SYSTEM  
SS01-71060-1E  
DSU-FR EMULATOR  
LQFP-64P HEADER TYPE 2  
MB2198-304  
OPERATION MANUAL  
 
The contents of this document are subject to change without notice.  
Customers are advised to consult with FUJITSU sales representatives before ordering.  
The information, such as descriptions of function and application circuit examples, in this document are presented sole-  
ly for the purpose of reference to show examples of operations and uses of FUJITSU semiconductor device; FUJITSU  
does not warrant proper operation of the device with respect to use based on such information. When you develop  
equipment incorporating the device based on such information, you must assume any responsibility arising out of such  
use of the information. FUJITSU assumes no liability for any damages whatsoever arising out of the use of the infor-  
mation.  
Any information in this document, including descriptions of function and schematic diagrams, shall not be construed  
as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right  
of FUJITSU or any third party or does FUJITSU warrant non-infringement of any third-party’s intellectual property  
right or other right by using such information. FUJITSU assumes no liability for any infringement of the intellectual  
property rights or other rights of third parties which would result from the use of information contained herein.  
The products described in this document are designed, developed and manufactured as contemplated for general use,  
including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not  
designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless  
extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal  
injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air  
traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2)  
for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).  
Please note that FUJITSU will not be liable against you and/or any third party for any claims or damages arising in  
connection with above-mentioned uses of the products.  
Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from  
such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire pro-  
tection, and prevention of over-current levels and other abnormal operating conditions.  
If any products described in this document represent goods or technologies subject to certain restrictions on export un-  
der the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be  
required for export of those products from Japan.  
Copyright ©2007 FUJITSU LIMITED All rights reserved  
ii  
 
1. Checking the Delivered Product  
Before using the MB2198-304, confirm that the following components are included in the box:  
LQFP-64P header board*1  
: 1  
: 4  
: 4  
: 1  
: 1  
: 1  
: 1  
Screws for securing the header board (M2 × 10mm, 0.4mm pitch)  
Washers  
NQPACK064SB*2  
HQPACK064SB140*3  
Operation manual (Japanese version)  
Operation manual (English version, this manual)  
*1 : The YQPACK064SB is mounted on the header board (Tokyo Eletech Corporation, referred to  
as the “YQPACK”).  
*2 : The IC socket (manufactured by Tokyo Eletech Corporation, referred to as “NQPACK”). This  
socket is supplied with a special screwdriver and 2 guide pins. Additionally, the relatively high  
reliability NQPACK064SB-SL (Tokyo Eletech Corporation, sold separately) can be used by  
preparing screw holes on the user system board for mounting the socket. For more information,  
contact Tokyo Eletech Corporation.  
*3 : The IC socket cover (manufactured by Tokyo Eletech Corporation, and referred to as “HQ-  
PACK”). This cover includes 4 screws for securing HQPACK (M2 × 6mm, 0.4mm pitch).  
This product is used as an emulator system by combining with an optional emulator, DSU cable and  
adapter.  
Consult a sales or support representative from Fujitsu Limited for details on the adapter and emulator  
for this product.  
2. Handling Precautions  
Handling precautions  
The header board is precision-manufactured to improve dimensional accuracy and to ensure reliable  
contact. The header is therefore sensitive to mechanical shock. To ensure correct use of the header  
in the proper environment, observe the following points regarding its insertion and removal:  
To avoid placing stress on the NQPACK mounted on the user system during connecting the  
header board.  
Precautions when operating on the sub clock  
When using this product, the evaluation MCU cannot be supplied with a sub clock from the user sys-  
tem.  
When the evaluation MCU is operating using the sub clock, use the sub clock on the adapter.  
Refer to the operation manual for the adapter for more details.  
1
 
3. Notes on Designing  
Notes on designing the printed circuit board for the user system  
If the header board is connected to a user system, the heights of parts mounted around the  
header board are restricted.  
When designing the printed circuit board of the user system, consider the heights of components  
within the range of the header board, as shown in Figure 1, so that the components mounted on the  
user system do not interfere with the header board.  
88.0mm  
52.0mm  
Adapter  
Insulating plate  
Header  
Approx.  
17.0mm*  
10.0mm  
User  
system  
1.6mm  
Approx.  
13.0mm*  
NQPACK064SB  
* : The height differs slightly depending on how the sockets are engaged.  
Figure 1 Header board dimensions  
2
 
MCU footprint design notes  
Figure 2 shows the recommended dimensions of the NQPACK footprint mounted on the printed cir-  
cuit board of the user system.  
The printed circuit board of the user system must be designed with due consideration given to this  
footprint as well as to the mass production MCU.  
For more information, contact the Tokyo Eletech Corporation.  
0.65mm × 15 = 9.75mm  
0.65mm  
0.4mm  
φ2.2mm*2  
3-φ1.0mm*1  
No.1 pin  
5.0mm  
12.0mm  
1.8mm  
1.8mm  
*1 : Position of the guide pin hole (φ1.0) when mounting the NQPACK.  
These holes do not need to be fabricated if the guide pins are not used.  
*2 : Position of the hole (φ2.2) for the screw for affixing the IC socket when the NQPACK064SB-SL  
(Tokyo Eletech Corporation, sold separately) is mounted instead of the NQPACK064SB-SL.  
This hole does not need to be fabricated if the NQPACK064SB-SL is not used.  
Figure 2 Recommended dimensions of the footprint for mounting the NQPACK  
3
 
4. Procedure for Connecting to the User System  
Before using the MB2198-304, mount the supplied NQPACK on the user system.  
Connect the header board directly to the adapter. Refer to the operation manual of the adapter for  
details on how to connect the adapter.  
Connecting  
1. To connect the header board to the user system, align pin 1 indicated by the index mark () on  
the NQPACK mounted on the user system with the index mark () on the header board and then  
insert it (See Figure 3) .  
The YQPACK pins are thin and easy to bend. Check that the YQPACK pins are not bent before  
inserting it into the NQPACK.  
2. Insert each of the screws for securing the header board through a washer and into each of the four  
holes in the header board. Partially tighten one of the screws with the special screwdriver supplied  
with the NQPACK and then partially tighten the screw in the diagonally opposite corner. Partially  
tighten the two remaining screws. Finally repeat the process making the screws equally tight.  
(See Figure 4) .  
Take care not to overtighten the screws as this may cause a faulty connection.  
Adapter I/F connector 1  
Adapter I/F connector 2  
YQPACK  
(It mounts at the back)  
NQPACK  
Index mark ()  
Header board  
Index mark ()  
Figure 3 Index position  
4
 
Screws for securing  
the header board  
Header board  
Washer  
YQPACK  
User system  
NQPACK  
Figure 4 Header board connection  
Disconnection  
To disconnect the header board from the user system, remove all four screws, and then pull the  
header board straight out of the NQPACK.  
5
 
5. Mounting Mass Production MCUs  
Use the supplied HQPACK to mount a mass production MCU on the user system.  
Mounting  
1. To mount a mass production MCU on the user system, align the index mark () on the NQPACK  
mounted on the user system with the index mark () on the mass production MCU.  
2. Confirm that the mass production MCU is correctly mounted on the NQPACK, and then align the  
index mark (the only corner with an angle cut-out) of the HQPACK with the index mark of the  
NQPACK, and insert it (See “Figure 5”).  
The HQPACK pins are thin and easy to bend. Check that the HQPACK pins are not bent before  
inserting it into the NQPACK.  
3. Insert each of the screws for securing the HQPACK into each of the four screw holes on the HQ-  
PACK and tighten the diagonally opposite screws in turn.  
To tighten the screws, use the special screwdriver supplied with the NQPACK to finally tighten  
the four screws in sequence. Tightening the screws too tight might result in a defective contact.  
Screws for securing  
the HQPACK  
HQPACK  
Mass production MCU  
User system  
NQPACK  
Figure 5 Mounting a mass production MCU  
Disconnection  
To remove the HQPACK, remove all of the four screws, and pull the HQPACK vertically out from  
the NQPACK.  
6
 
6. Connector Pin Assignment  
The signals from the evaluation MCU mounted on the adapter board are connected to the YQPACK  
(the same assignments as mass production MCU) via adapter I/F connectors 1 and 2 on the header  
board.  
For details on the mass production MCU pins, refer to the data sheet or hardware manual of each  
MCU.  
Pin assignment  
Tables 1 to 4 show the correspondence between the pin numbers for adapter I/F connectors 1 and 2,  
the evaluation MCU on the adapter board, and the mass production MCU.  
The following explanations apply to these tables. Row A corresponds to the side of the connector  
that displays the polarity. Row B corresponds to the opposite side.  
*1 : No connection. These are not connected on either evaluation MCUs or mass production MCUs.  
*2 : Pin 18 on mass production MCUs is connected to pins AA38, Y37, Y36, and Y35 on evaluation  
MCUs.  
-
: Unconnected (open) pin  
:
VCC  
The evaluation MCU power supply pins (VCC) are as follows:  
VCC=Y38, W38, W36, W35, G5, L5, AR7, AM35, H35, D8, R5, W5, AC5, AG5, AP11,  
AP19, AP23, AP31, AH34, AD34, T34, H34, E32, E28, E20, E12, G4, AL4, AR31,  
D32, AL5, AP7, AP15, AP27, AR7, AM34, Y34, M34, E24, E16, E8, AP33, AP29,  
AP25, AP21,AP13, AA5, D15, D25, R35, AE35, AR24, P4, AP17, AP9, AN5, AJ5,  
AE5, U5, N5, J5,AR14, AD4, AK34, AF34, AB34, V34, P34, K34, F34, E30, E26, E22,  
E18, E14, E10, E6  
The mass production MCU power supply (VCC) pin numbers are 16 and 48.  
VSS  
:
The evaluation MCU ground pins (VSS) are as follows:  
VSS = E11, E15, E19, E23, E27, E31, G34, L34, R34, W34, AA34, AE34, M5, C3, B37, T5,  
Y5, AD5, AJ34, AH5, AT36, AT3, AU37, AU2, AK5, AP8, AP12, AP16, AP20, AP24,  
AP28, AP30, AL34, A1, B1, AU1, AV1, AV2, AV37, AV38, AU38, B38, A38, A37,  
A2, C36, D4, AR4, AR35, D35, E5, K5, P5, V5, AB5, AF5, AM5, AP5, AP6, AP10,  
AP14, AP18, AP22, AP26, AP32, AP34, AN34, AG34, AC34, U34, N34, J34, E34,  
E33, E29, E25, E21, E17, E13, E7  
The mass production MCU ground (VSS) pin numbers are 17, 33, and 49.  
7
 
Table 1 Adapter I/F Connector 1 (Row A)  
Connector  
Pin No.  
MassProduction Evaluation MCU  
Connector  
Pin No.  
MassProduction Evaluation MCU  
MCU Pin No.  
Pin No.  
MCU Pin No.  
Pin No.  
A1  
A2  
A3  
A4  
A5  
A6  
A7  
A8  
VCC  
VCC  
A51  
A52  
A53  
A54  
A55  
A56  
A57  
A58  
A59  
A60  
A61  
A62  
A63  
A64  
A65  
A66  
A67  
A68  
A69  
A70  
A71  
A72  
A73  
A74  
A75  
A76  
A77  
A78  
A79  
A80  
A81  
A82  
A83  
A84  
A85  
A86  
A87  
A88  
A89  
A90  
A91  
A92  
A93  
A94  
A95  
A96  
A97  
A98  
A99  
A100  
GND  
GND  
-
-
-
-
-
-
-
-
J36  
H37  
K36  
J35  
J83  
K35  
J37  
-
-
-
-
-
-
-
-
C30  
A32  
C31  
D30  
B31  
D31  
B32  
A33  
A9  
A10  
A11  
A12  
A13  
A14  
A15  
A16  
A17  
A18  
A19  
A20  
A21  
A22  
A23  
A24  
A25  
A26  
A27  
A28  
A29  
A30  
A31  
A32  
A33  
A34  
A35  
A36  
A37  
A38  
A39  
A40  
A41  
A42  
A43  
A44  
A45  
A46  
A47  
A48  
A49  
A50  
K38  
GND  
GND  
GND  
GND  
-
-
-
-
-
-
-
-
E38  
F37  
F38  
G35  
G38  
H36  
G37  
H38  
61  
62  
59  
60  
-
-
-
-
D28  
A30  
D29  
C28  
B29  
C29  
B30  
A31  
GND  
GND  
GND  
GND  
-
-
-
-
-
-
-
-
C38  
D37  
D38  
E35  
F36  
F35  
E37  
G36  
32  
31  
42  
41  
-
-
-
-
-
C26  
A28  
C27  
D26  
B27  
D27  
A29  
B28  
AC38  
AB36  
AC36  
AC35  
GND  
GND  
-
-
-
-
-
-
-
-
-
-
-
C34  
A36  
C35  
B35  
D36  
B36  
E36  
C37  
GND  
-
-
-
-
-
-
-
-
AF38  
AD36  
AE36  
AG38  
-
AD3  
AC3  
-
GND  
GND  
-
-
-
-
-
-
-
-
C32  
A34  
C33  
B33  
D33  
B34  
D34  
A35  
VCC  
GND  
40  
-
AD1  
AD2  
GND  
GND  
NC*1  
8
 
Table 2 Adapter I/F Connector 1 (Row B)  
Connector  
Pin No.  
MassProduction Evaluation MCU  
Connector  
Pin No.  
MassProduction Evaluation MCU  
MCU Pin No.  
Pin No.  
MCU Pin No.  
Pin No.  
B1  
B2  
B3  
B4  
B5  
B6  
B7  
B8  
-
-
-
-
-
-
-
-
-
-
-
-
B51  
B52  
B53  
B54  
B55  
B56  
B57  
B58  
B59  
B60  
B61  
B62  
B63  
B64  
B65  
B66  
B67  
B68  
B69  
B70  
B71  
B72  
B73  
B74  
B75  
B76  
B77  
B78  
B79  
B80  
B81  
B82  
B83  
B84  
B85  
B86  
B87  
B88  
B89  
B90  
B91  
B92  
B93  
B94  
B95  
B96  
B97  
B98  
B99  
B100  
GND  
GND  
B23  
A26  
B24  
C24  
B25  
C25  
B26  
A27  
57  
58  
-
56  
54  
55  
-
B13  
A14  
C15  
B14  
B15  
C16  
B16  
A15  
B9  
B10  
B11  
B12  
B13  
B14  
B15  
B16  
B17  
B18  
B19  
B20  
B21  
B22  
B23  
B24  
B25  
B26  
B27  
B28  
B29  
B30  
B31  
B32  
B33  
B34  
B35  
B36  
B37  
B38  
B39  
B40  
B41  
B42  
B43  
B44  
B45  
B46  
B47  
B48  
B49  
B50  
53  
GND  
GND  
GND  
GND  
51  
52  
47  
50  
45  
46  
43  
44  
C22  
A24  
C23  
B21  
D23  
B22  
A25  
D24  
22  
21  
24  
23  
13  
12  
-
B11  
A12  
C13  
B12  
C9  
B8  
A13  
D14  
-
GND  
GND  
GND  
GND  
-
-
-
-
-
-
-
-
D20  
B20  
D21  
A21  
C21  
A22  
D22  
A23  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
B9  
A10  
C11  
B10  
D11  
C12  
D12  
A11  
AD38  
AA37  
AB37  
AD35  
AE38  
AC37  
AD37  
AE37  
GND  
GND  
-
-
-
-
-
-
-
-
D18  
A18  
D19  
B19  
C19  
A19  
C20  
A20  
GND  
VCC  
-
-
-
-
-
GND  
GND  
L4  
L3  
-
26  
25  
-
27  
29  
28  
-
D16  
A16  
C17  
D17  
C18  
B17  
A17  
B18  
18  
-
-
-
-
*2  
-
-
-
-
NC*1  
30  
9
 
Table 3 Adapter I/F Connector 2 (Row A)  
Connector  
Pin No.  
MassProduction Evaluation MCU  
Connector  
Pin No.  
MassProduction Evaluation MCU  
MCU Pin No.  
Pin No.  
MCU Pin No.  
Pin No.  
A1  
A2  
A3  
A4  
A5  
A6  
A7  
A8  
VCC  
VCC  
A51  
A52  
A53  
A54  
A55  
A56  
A57  
A58  
A59  
A60  
A61  
A62  
A63  
A64  
A65  
A66  
A67  
A68  
A69  
A70  
A71  
A72  
A73  
A74  
A75  
A76  
A77  
A78  
A79  
A80  
A81  
A82  
A83  
A84  
A85  
A86  
A87  
A88  
A89  
A90  
A91  
A92  
A93  
A94  
A95  
A96  
A97  
A98  
A99  
A100  
GND  
GND  
11  
10  
-
B7  
A8  
C14  
D13  
C10  
D9  
3
2
5
4
7
6
9
8
J1  
L2  
C2  
D3  
B3  
C4  
B4  
C5  
-
15  
14  
20  
19  
A9  
A9  
D10  
A10  
A11  
A12  
A13  
A14  
A15  
A16  
A17  
A18  
A19  
A20  
A21  
A22  
A23  
A24  
A25  
A26  
A27  
A28  
A29  
A30  
A31  
A32  
A33  
A34  
A35  
A36  
A37  
A38  
A39  
A40  
A41  
A42  
A43  
A44  
A45  
A46  
A47  
A48  
A49  
A50  
GND  
GND  
GND  
GND  
-
-
-
-
-
-
-
-
E2  
F2  
D1  
F4  
C1  
E4  
D2  
E3  
-
-
-
-
-
-
-
-
L1  
N2  
N4  
N3  
M4  
M3  
K1  
M2  
GND  
GND  
GND  
GND  
-
-
-
-
-
-
-
-
H4  
J4  
-
-
-
-
-
-
-
-
-
-
-
-
N1  
P1  
R3  
T2  
P3  
R2  
M1  
P2  
AF37  
AF36  
AG36  
AG37  
F1  
H2  
E1  
G2  
F3  
G3  
GND  
GND  
-
-
-
-
-
-
-
-
K3  
K4  
H1  
K2  
G1  
J2  
GND  
-
-
-
AK38  
AH36  
AJ36  
AL38  
AE1  
AE2  
-
A6  
C8  
E9  
H3  
J3  
-
39  
37  
-
63  
64  
64  
GND  
GND  
-
-
-
-
-
-
-
-
D5  
A3  
D6  
A4  
C7  
C6  
A5  
B5  
VCC  
GND  
-
AB38  
GND  
GND  
10  
 
Table 4 Adapter I/F Connector 2 (Row B)  
Connector  
Pin No.  
MassProduction Evaluation MCU  
Connector  
Pin No.  
MassProduction Evaluation MCU  
MCU Pin No.  
Pin No.  
MCU Pin No.  
Pin No.  
B1  
B2  
B3  
B4  
B5  
B6  
B7  
B8  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
R1  
U4  
V2  
U3  
U2  
T3  
R4  
T4  
B51  
B52  
B53  
B54  
B55  
B56  
B57  
B58  
B59  
B60  
B61  
B62  
B63  
B64  
B65  
B66  
B67  
B68  
B69  
B70  
B71  
B72  
B73  
B74  
B75  
B76  
B77  
B78  
B79  
B80  
B81  
B82  
B83  
B84  
B85  
B86  
B87  
B88  
B89  
B90  
B91  
B92  
B93  
B94  
B95  
B96  
B97  
B98  
B99  
B100  
-
-
-
L37  
M38  
M37  
GND  
GND  
-
-
-
-
-
-
N35  
N36  
P35  
P36  
P38  
N38  
B9  
B10  
B11  
B12  
B13  
B14  
B15  
B16  
B17  
B18  
B19  
B20  
B21  
B22  
B23  
B24  
B25  
B26  
B27  
B28  
B29  
B30  
B31  
B32  
B33  
B34  
B35  
B36  
B37  
B38  
B39  
B40  
B41  
B42  
B43  
B44  
B45  
B46  
B47  
B48  
B49  
B50  
-
-
-
-
-
-
-
-
-
-
N37  
R36  
P37  
R37  
T36  
T37  
R38  
T35  
T38  
U35  
GND  
GND  
-
-
-
-
-
-
-
-
W2  
W3  
V1  
W4  
U1  
V4  
T1  
V3  
GND  
GND  
GND  
GND  
-
-
-
-
-
-
U37  
U36  
V37  
V36  
V38  
U38  
-
-
-
-
-
-
-
-
AA1  
AB1  
Y2  
AA4  
Y1  
Y4  
W1  
Y3  
-
-
-
-
-
-
-
-
-
V35  
AH38  
AF35  
AG35  
AH37  
AJ38  
AH35  
AJ35  
AJ37  
GND  
GND  
-
-
-
-
-
-
-
-
AC1  
AC2  
AB4  
AC4  
AB2  
AB3  
AA2  
AA3  
GND  
38  
-
-
1
1
AF2  
-
-
D7  
B6  
A7  
GND  
GND  
-
-
-
-
-
-
L36  
K37  
L35  
M36  
M35  
L38  
63  
VCC  
GND  
34  
35  
AA36  
AB35  
GND  
11  
 
SS01-71060-1E  
FUJITSU SEMICONDUCTOR SUPPORT SYSTEM  
DSU-FR EMULATOR  
LQFP-64P HEADER TYPE 2  
MB2198-304  
OPERATION MANUAL  
February 2007 the first edition  
Published FUJITSU LIMITED Electronic Devices  
Edited Business Promotion Dept.  
 
 

Dyson Vacuum Cleaner DC35 User Manual
Electro Voice Microphone N D308 User Manual
Extron electronic Network Card 70 110 04 User Manual
Extron electronic Stereo Receiver MLC 62 D User Manual
Extron electronic Stereo Receiver MTP U Series User Manual
Fisher Price Baby Toy 74123 User Manual
Fujitsu Printer FTP 621MCL101 User Manual
Fujitsu Printer FTP 621MCL301 User Manual
GE Telephone Feb 96 User Manual
Gitzo Camcorder Accessories GT2541G User Manual