24V, 2" HIGH SPEED THERMAL PRINTER
FTP-627 Series
■ OVERVIEW
The FTP-627 MCL Series consists of 24V drive ultra compact
printers with 2 inch paper widths (58mm), which can print at
high speed. Paper can be easily set by an unique platen
release mechanism.
The FTP-627 MCL series can be used for a variety of
applications, such as portable terminals, POS, ticket issuing
terminals, label printers, and measurement and medical
equipment.
■ HIGHLIGHTS
• Ultra compact
Height 15.5 mm, width 69.6 mm, depth 34.3 mm (MCL002)
• High speed printing
It can print at 60 mm/s (480 dotlines/s) maximum by using
Fujitsu's unique head drive control.
• With Auto Cutter
Two types of compact cutters, a full cut and a partial cut, are
in series.
• High resolution printing / Kanji supported
8 dots/mm of resolution printing is possible.
• Easy paper setting
Our unique platen release mechanism allows a
wide paper route even if the printer is ultra-compact, so
paper can be easily inserted. Auto loading is also available
on MCL001, MCL003 and MCL303 models.
• Two types of paper routes
Front and bottom paper feed.
• Easy mounting
Head, motor, sensor and other component wiring are unified
to one flexible cable, and the mechanism can be secured by
one hook and two screws at two locations, making mounting
easy.
1
FTP-627MCL Series
■ SPECIFICATIONS
Item
Specification
Interface
Conforms to RS232C / Centronics
24 VDC ±5% average current, current approx. 1.1A (25 ˚ C,
Rav=1500) 24V, simultaneously ON, 64 dots)
For print head
Power
supply
For motor of printer
For motor of cutter
24 VDC ±5%, 1A maximum
24 VDC ±5%, 1 A maximum
For logic
5 VDC ± 5%, 0.2 A maximum
Printer mechanism
Mechanism with cutter
Interface board
83.5 x 35.7 x 15.5 mm (WxDxH), MCL003 (lever excluded)
83.5 x 43.0 x 26.4mm (WxDxH), (screws and cables are excluded)
131 x 89 x 24 mm
Dimensions
Weight
Printer mechanism without
cutter
Approximately 55g
Approximately 120g
Printer mechanism with
cutter
Pulse resistance: 100 million pulses/dot (under our standard
conditions). Abrasion resistance: paper traveling distance 50km
(print ratio: 25% or less)
Head
Life
Cutter
300,000 minimum
+5˚ C to +40˚ C (printing density assurance range, operation is
possible at 0˚ C to +40˚ C)
Operating temperature
Operating
environment
Operating humidity
Storage temperature
Storage humidity
20 to 85% RH (no condensation)
-20˚ C to +60˚ C (paper not included)
5-95% RH (no condensation)
Head temperature detection Detected by thermistor
Detection
function
Paper out/mark detection
Head up detection
Detected by photo-interrupter
Detected by slide-switch (003/004/303#1/303#2 only)
High sensitive paper:
Standard paper:
TF50KS-E4 (Nippon Paper)
F60KS-E (Nippon Paper)
FTP-020PU001, FTP-020P0104 (58mm)
PD150R (Oji Paper)
FTP-020P0701(58mm)
Medium life storage
paper:
TF60KS-F1 (Nippon Paper)
FTP-P0102 (58mm)
Recommended thermal sensitive paper
PD170R (Oji Paper)
P220VBB-1 (Mitsubishi Paper)
Long life storage paper:
PD60R-N (Oji Paper)
AFP-235 (Mitsubishi Paper)
TP50KJ-R (Nippon Paper)
HA220AA (Mitsubishi Paper)
3
FTP-627MCL Series
■ FUNCTION
Item
Item
1.
2.
3.
4.
Test print function
8.
9.
Cutter abnormality detection
Motor power saving function
Paper out detection
Paper near end detection
Head up detection
10. Mark detection function
11. MCU operation abnormality detection
Thermal head temperature abnormality
detection
5.
12. Power ON/OFF sequence protection
6.
7.
Blow-out fuse detection
13. Motor over-current protection
14. Hardware timer
Head voltage abnormality detection
■ DIMENSIONS
1. Printer mechanism
Unit: mm
4
FTP-627MCL Series
2. Interface board
130.8
83.8
55.9
6.4
4 - ø 3.6±0.1
CN10
CN11*
CN8
CN1
30.5
CN2
CN5**
5.1
91.4
5.1
120.7
Part mounting side
Part solder side
* CN11 used
** CN5 used for paper near end detection
Unit: mm
5
FTP-627MCL Series
■ PRINTER CONNECTOR (CN8) (FLEXIBLE PT BOARD) PIN ARRAYS
Control circuit side connector: 52030-3010 Molex or equivalent product
No.
1
Signal
PHK
I/O
Contents
Photo interrupter (cathode)
Photo interrupter (emitter)
Head driving power supply
Ground for head
Data latch
No.
2
Signal
VSEN
I/O
Contents
Power supply for paper sensor
Head driving power supply
Ground for head
Data input
—
O
I
I
I
3
PHE
VH
4
VH
5
6
GNC
DIN
—
I
7
GND
LAT
—
I
8
9
10
12
14
16
18
20
22
24
26
28
CLK
STB5
VDD
STB 2
TH
I
Clock
11
13
15
17
19
21
23
25
27
STB6
STB4
STB3
STB1
TH
I
Enable 6
I
Enable 5
I
Enable 4
I
Logic Power supply
Enable 2
I
Enable 3
I
I
Enable 1
O
—
I
Thermistor
O
—
I
Thermistor
GND
VH
Ground for head
Head driving power supply
Open terminal
GND
VH
Ground for head
Head driving power supply
Head open switch*
N.C.
SW2
MT/B
—
O
I
SW1
MT/B
I
Head open switch*
I
Stepping motor coil
excitation signal B
Stepping motor coil
excitation signal B
29
MT/A
I
Stepping motor coil
excitation signal A
30
MT/A
I
Stepping motor coil
excitation signal A
* on MCL003 / MCL004/ MCL303#01 and MCL303#02 models
6
FTP-627MCL Series
■ INTERFACE
1. Centronics interface
(1) Connector (CN1)
Connector part number
: FCN-605Q030-G/S (Fujitsu Components) or equivalent
Mating connector part number : FCN-607B030-G/D (Fujitsu Components) or equivalent
(2) Connector pin assignment
No.
1
Signal
PRSTB
I/O
Contents
Data strobe
No.
2
Signal
I/O
—
—
—
—
—
—
—
—
—
—
—
—
I
Contents
I
I
PRSTB-RET
PRDT0-RET
PRDT1-RET
PRDT2-RET
PRDT3-RET
PRDT4-RET
PRDT5-RET
PRDT6-RET
PRDT7-RET
ACKNLG-RET
BUSY-RET
INPRM-RET
INPRM
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Reset
3
PRDT0
PRDT1
PRDT2
PRDT3
PRDT4
PRDT5
PRDT6
PRDT7
ACKNLG
BUSY
Data 0
4
5
I
Data 1
6
7
I
Data 2
8
9
I
Data 3
10
12
14
16
18
20
22
24
26
28
30
11
13
15
17
19
21
23
25
I
Data 4
I
Data 5
I
Data 6
I
Data 7
O
O
O
I
Data input acknowledge
Busy
RINF2
SLCTIN
RINF1
ATF
Printer status 2
Printer select
Printer status 1
Paper feed request
27
29
O
I
RINF3
O
Printer status 3
GND
—
Logic GND
Notes:
• Symbol “——” means a negative logic signal.
• “–RET” signal is a return signal of the twisted pair cable.
• “I” or “O” means a signal direction from the interface board side.
(3) Connector pin number
(4) Data input signal timing
FCN-605Q030-G/S(Fujitsu Components)
PRDT0~7
t1
t3
PRSTB
BUSY
t2
t4
ACKNLG
t5
Data set time
PRSTB pulse width
Data hold time
PRSTB to BUSY= “H”
ACKNLG pulse time
:t1≥0.5 µsec
:t2≥0.5 µsec
:t3≥0.5 µsec
:t4≤0.5 µsec
:t5≈ 5.0 µsec
7
FTP-627MCL Series
(5) Printer status signals
Error status
RINF1
Low
RINF2
High
High
Low
RINF3
Low
1. Paper out
2. Paper near end
High
High
High
Low
Low
3. Head up
Low
4. Head temperature abnormality
5. Head voltage abnormality
6. Hardware abnormality
7. Mark detection abnormality
8. Normal
Low
High
High
High
Low
High
High
Low
High
Low
Low
Low
High
2. RS-232C
(1) Connector (CN2)
Connector part number
: B6B-XH-A (J.S.T.) or equivalent
Mating connector part number : XHP-6 (J.S.T.) or equivalent
(2) Connector pin assignment
No.
1
Signal
FG
I/O
-
Contents No.
Frame ground
No.
2
Signal
RD
I/O
Contents No.
I
O
I
Receive data
3
TD
O
-
Transmission data
Signal ground
4
DTR
DSR
Data terminal ready
Data set ready
5
GND
6
7
9
SLCTIN
ATF
I
I
Printer select
8
INPRM
I
I
Reset
Power down cancellation
signal
Paper feed request
10 PWD
Notes:
• Symbol “——” means a negative logic signal.
• “I” or “O” means a signal direction from the interface board side.
Cutter (CN11)
8
FTP-627MCL Series
■ CONNECTOR PIN ASSIGNMENT
1. Connector for power supply (CN10)
Part number
: B6B-VH White (J.S.T) or equivalent (board side)
Mating connector part number: VHR-6 (J.S.T.) or equivalent
2. Connector for printer mechanism connection (CN8)
Part number
: 52030-3010 (made by Molex) or equivalent (board side)
No.
Signal
PHK
I/O
—
I
Contents
Photo interrupter (cathode)
Photo interrupter (emitter)
Head driving power supply
Ground for head
Data latch
No.
2
Signal
VSEN
I/O
O
O
—
O
O
O
O
O
I
Contents
Power supply for paper senor
Head driving power supply
Ground for head
Data input
1
3
PHE
VH
4
VH
5
O
—
O
O
O
O
O
I
6
GNC
DIN
7
GND
LAT
8
9
10
12
14
16
18
20
22
24
26
28
CLK
STB5
VDD
STB 2
TH
Clock
11
13
15
17
19
21
23
25
27
STB6
STB4
STB3
STB1
TH
Enable 6
Enable 5
Enable 4
Logic Power supply
Enable 2
Enable 3
Enable 1
Thermistor
Thermistor
GND
VH
—
O
—
I
Ground for head
Head driving power supply
Open terminal
GND
VH
—
O
O
O
Ground for head
Head driving power supply
Head open switch*
N.C.
SW2
MT/B
SW1
MT/B
Head open switch*
Stepping motor coil
excitation signal B
O
Stepping motor coil
excitation signal B
29
MT/A
O
Stepping motor coil
excitation signal A
30
MT/A
O
Stepping motor coil
excitation signal A
* on MCL003 / MCL004/ MCL303#01 and MCL303#02 models
9
FTP-627MCL Series
■ OPTIONS
Name
Part Number
Length (mm)
500
Interface Cable
(between board and
equipment)
For Centronics (CN1) FTP-622Y201
For RS232C (CN2)
FTP-622Y301
FTP-622Y401
FTP-
300
300
Power supply cable (CN10)
Near end paper sensor (CN5) if required
10
FTP-627MCL Series
■ COMMANDS
Command
Contents
Moves print position to the next tab.
Line feed.
HT
LF
FF
Feeds forms (new page).
Sets reverse printing.
ECS RS
ESC US
Resets reverse printing.
Sets print mode.
ESC ! + n
ESC %+n
ESC &+y+c1+c2+x+d1~dN
ESC *+m+n1+n2+d1~dN
ESC ?+n
ESC 2
Download character set specification//cancellation.
Download character definition.
Sets bit image mode.
External registration character deletion.
Sets 1/6 inch line feed length.
Sets the line feed length.
ESC 3+n
ESC @
Printer initialization.
ESC A+n
ESC C+n
ESC D+d1~dN+NUL
ESC J+n
ESC K+n
ESC R+n
ESC c+1+n
ESC d+n
ESC e+n
ECS s+n
ECS t+n
Sets the space between the line.
Sets the page length by character line.
Sets the tab position.
Feeds paper in forward direction and prints.
Reverse paper feed.
Selects international character.
Sets internal processing (including auto paper loading).
Printing and n-line feeding.
Prints and reverse feeds n-lines.
Sets printing speed.
Character code table selection.
Sets/resets upside down printing.
Kanji printing mode collective specification.
Kanji printing mode specification.
Kanji printing mode cancellation.
Sets the detection functions.
ESC {+n
FS !+n
FS &
FS .
FS 9+n
11
FTP-627MCL Series
Commands continued
Command
Contents
FS C+n
Kanji code system selection.
FS W+n
Kanji double height and width mode specification/cancellation.
Line feeds to the next mark.
GS <
GS A+m+n
GS E+n
Sets the line feed length after mark detection.
Sets print quality.
GS V+n+m
GS e+n+m
GS h+n
Paper cutting.
Sets bar code width.
Sets bar code height.
GS k+m+n+d1~dN
GS w+n
Selects bar code type and prints.
Sets bar code width magnification.
High speed collective image printing specified.
Registration of image data.
FS *+m+n1+n2+d1~dN
GS &+m+x+y1+y2+d1~dN
GS '+m+n
FS E+n
Prints registered image data.
Correction of impressed energy.
ESC V+n
Right Rotation 90° specification / cancellation.
Sets and cancels status transmission. (Serial Mode)
Parameter transmission. (Serial Mode)
Setting the amount of the feeding at automatic paper load.
Setting the turning time of the motor excitation.
Deletes recorded contents in flash memory.
GS a+n
FS r+n
ESC EM+n
ESC X+n+m
ESC DEL+n
Europe
Japan
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Fujitsu Components
International
Headquarter
Offices
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: [email protected]
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: [email protected]
Asia Pacific
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (1-408) 745-4970
Fax: (65) 6273-3021
Email: [email protected]
Email: [email protected]
© 2003 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 04/03/2003
12
|