FUJITSU SEMICONDUCTOR
SUPPORT SYSTEM
SS01-71045-1E
F2MC-16 Family EMULATOR
QFP-100P PROBE HEADER
MB2147-583
OPERATION MANUAL
• The contents of this document are subject to change without notice.
Customers are advised to consult with FUJITSU sales representatives before ordering.
• The information, such as descriptions of function and application circuit examples, in this document are presented sole-
ly for the purpose of reference to show examples of operations and uses of FUJITSU semiconductor device; FUJITSU
does not warrant proper operation of the device with respect to use based on such information. When you develop
equipment incorporating the device based on such information, you must assume any responsibility arising out of such
use of the information. FUJITSU assumes no liability for any damages whatsoever arising out of the use of the infor-
mation.
• Any information in this document, including descriptions of function and schematic diagrams, shall not be construed
as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right
of FUJITSU or any third party or does FUJITSU warrant non-infringement of any third-party’s intellectual property
right or other right by using such information. FUJITSU assumes no liability for any infringement of the intellectual
property rights or other rights of third parties which would result from the use of information contained herein.
• The products described in this document are designed, developed and manufactured as contemplated for general use,
including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not
designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless
extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal
injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air
traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2)
for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that FUJITSU will not be liable against you and/or any third party for any claims or damages arising in
connection with above-mentioned uses of the products.
• Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from
such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire pro-
tection, and prevention of over-current levels and other abnormal operating conditions.
• If any products described in this document represent goods or technologies subject to certain restrictions on export un-
der the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be
required for export of those products from Japan.
©2005 FUJITSU LIMITED Printed in Japan
1. Checking the Delivered Product
Before using the QFP-100P probe header, confirm that the following components are included in the
box:
• QFP-100P Probe Header *1
: 1
: 4
: 4
: 1
: 1
: 1
: 1
• Screws for securing header board (M2 × 10 mm, 0.4 mm pitch)
• Washer
• NQPACK100RB179 *2
• HQPACK100RB179 *3
• Operation manual (Japanese version)
• Operation manual (English version, this manual)
*1 : Referred to as "header board". Header board is mounted on the YQPACK100RB179 (Tokyo
Eletech Corporation), referred to as “YQPACK”.
*2 : IC socket manufactured by Tokyo Eletech Corporation, referred to as “NQPACK”, and sup-
plied with a special screwdriver and 3 guide pins. A socket offering higher reliability,
NQPACK100RB179-SL (Tokyo Eletech Corporation, sold separately), can be used by making
an IC socket mounting hole on the user system board. For more information, contact Tokyo
Eletech Corporation.
*3 : IC Socket cover manufactured by Tokyo Eletech Corporation, referred to as “HQPACK”, with
4 screws for securing HQPACK (M2 × 6 mm, 0.4 mm pitch).
This product is used as an emulator system by combining with an optional emulator and adapter
board.
Consult the Sales Department or the Support Department of Fujitsu Limited for the adapter or the
emulator of this product.
2. Handling Precautions
The header board is precision-manufactured to improve dimensional accuracy and to ensure reliable
contact. The header is therefore sensitive to mechanical shock. To ensure correct use of the header
in the proper environment, observe the following points regarding its insertion and removal:
• To avoid placing stress on the NQPACK mounted on the user system board during connecting
the header board.
1
3. Notes on Designing
■ Restrictions of PC board for the user system
Once the header board is connected to the user system, the heights of parts mounted in the space
around the header board are restricted.
The PC board of the user system must be designed with due consideration given to this restriction
(Figure 1).
77.0 mm
40.0 mm
1
2
1
2
80.0 mm
50.0 mm
99
100 99
100
Approximately
30.0 mm *
Approximately
13.0 mm *
* : The height differs slightly depending on how the YQPACK and the NQPACK are en-
gaged.
Figure 1 Header board dimensions
2
■ MCU footprint design notes
Figure 2 shows the recommended dimensions of the NQPACK footprint mounted on the PC board
of the user system.
The PC board of the user system must be designed with due consideration given to this footprint as
well as to the mass production MCU.
For more information, contact the Tokyo Eletech Corporation.
0.65
0.35
UNIT : mm
No.1 Pin
6.0
φ 3.2*2
3 - φ 1.0*1
13.8
2.4
*1 : It is a position of hole (φ1.0) for the guide pin to fit position when NQPACK is mounted.
When the guide pin is not used, it is not necessary to puncture it.
*2 : It is a fixation of screw hole(φ3.2) for IC socket made when NQPACK100RB179-
SL(Tokyo Eletech Corporation, sold separately) is mounted.
When the NQPACK100RB179-SL is not used, it is not necessary.
Figure 2 Recommended dimensions of the footprint for mounting the NQPACK
3
4. Procedure for Connecting the User System
Before using the QFP-100P probe header, mount the supplied NQPACK on the user system.
The header board is used combining the adapter board. To connect the header board to the adapter
board, use the flat cable (2 lines) supplied by the emulator sold separately. Refer to the hardware
manuals of the adapter board about the way to connect.
■ Connecting
1. To connect the header board to the user system, match the index mark (■) on the NQPACK-
mounted on the user system with the index mark (■) on the header board and then insert it (See
Figure 3) . The pin of YQPACK is thin and easy to bent. Insert NQPACK after confirm that thep-
in of YQPACK is not bent.
2. Insert each screw for securing header board in each of the four drilled holes on the header
board(See Figure 4).
To tighten the screws, use the special screwdriver supplied with the NQPACK to finally tighten-
the four screws in sequence. Tightening the screws too tight might result in a defective contact.
Probe cable connector B1
Probe cable connector B2
YQPACK
(It arranges at the back)
User System
1 0 0 R B
T E T
NQPACK Index (■)
Header board Index (■)
Figure 3 Index Position
4
Screws for securing
header board
Header board
Washer
YQPACK
User system
NQPACK
Figure 4 Header board connection
■ Disconnection
To disconnect the header board from the user system, remove all four screws, and then pull the head-
er board straight out of the socket
5
5. Mounting Mass Production MCUs
To mount a mass production MCU on the user system, use the supplied HQPACK (See Figure 5).
■ Mounting
1. To mount a mass production MCU on the user system, match the index mark (■) on the NQ-
PACK mounted on the user system with the index mark (■) on the mass production MCU.
2. Confirm that the mass production MCU is correctly mounted on the NQPACK. Next, insert the
HQPACK into a NQPACK.
The pin of HQPACK is thin and easy to bent. Insert NQPACK after confirm that the pin of HQ-
PACK is not bent.
3. Insert each screw for securing HQPACK in each of the four drilled holes on the HQPACK (See
Figure 5).
To tighten the screws, use the special screwdriver supplied with the NQPACK to finally tighten
the four screws in sequence. Tightening the screws too tight might result in a defective contact.
Screws for securing HQPACK
HQPACK
Mass production MCU
User system
NQPACK
Figure 5 Mounting a mass production MCU
■ Disconnection
To remove the HQPACK, remove all four screws, and pull out the HQPACK vertically.
6
6. Connector Pin Assignment
The signal of Evaluation MCU with which it was carried on the adapter board is connected to YQ-
PACK(the same assignments as production MCU) via the probe cable connector(B1,B2) on a header
board.
An adapter board and a header board are connected to an emulator main part by the attached flat ca-
ble (It is used standard 2 or two long.)connector.
Please check the hardware manual of an emulator or an adapter board about reference of the connec-
tion method.
■ Pin Assignment
Tables 1 and 2 list the pin assignments among the flat cable connector, the evaluation MCU on the
adapter board, and the production MCU.
For details on the names of signal conductors of the evaluation MCU, refer to the hardware manual
for the adapter board.
Comments in the tables are given below.
*1 : Connected to the main power supply of the evaluation MCU.
*2 : Connected to the main power supply (Vcc) of the production MCU. The connection pin num-
bers are 15 and 90.
*3 : Connected to the ground of the evaluation MCU.
*4 : Connected to the ground (Vss) of the production MCU. The connection pin numbers are 16,
44 and 91.
- : Unconnected pin (left open).
7
Table 1 Pin assignment of the probe cable connector B1
Probe cable-
Probe cable-
Evaluation
MCU
Production
MCU
Evaluation
MCU
Production
MCU
Connector
Pin
Numbers
100
98
Connector
Pin
Numbers
99
97
95
93
91
89
87
85
83
81
79
77
75
73
71
69
67
65
63
61
59
57
55
53
51
49
47
45
43
41
39
37
35
33
31
29
27
25
23
21
19
17
15
13
11
9
Pin Numbers Pin Numbers
Pin Numbers Pin Numbers
*3
*3
208
259
79
147
78
*3
146
223
26
94
219
*3
*4
*4
43
40
39
37
36
*4
33
⎯
⎯
74
73
*4
*2
58
57
55
⎯
*4
64
59
47
17
*4
*4
69
66
⎯
⎯
⎯
*4
⎯
⎯
45
23
22
*4
19
12
11
9
*3
80
148
*3
207
258
206
77
160
*3
268
269
95
33
169
*3
34
167
35
225
32
*3
106
163
162
96
270
*3
221
273
271
222
99
*4
42
41
*4
38
35
34
32
49
*4
⎯
72
71
63
62
*4
56
⎯
48
60
61
*4
46
65
70
68
67
*4
⎯
⎯
⎯
76
75
*4
24
21
20
18
*2
*4
10
7
96
94
92
90
88
86
84
82
80
78
76
74
72
70
68
66
64
62
60
58
56
54
52
50
48
46
44
42
40
38
36
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
*1
226
275
105
224
*3
274
104
170
227
*3
*3
220
100
97
164
98
*3
23
165
276
108
172
*3
229
130
292
131
247
*3
*3
107
277
109
173
228
*3
193
194
132
*3
8
*4
5
6
*4
4
*4
1
98
97
*4
293
248
133
62
61
*3
195
63
3
2
100
99
*4
7
5
134
*3
3
1
294
*3
8
Table 2 Pin assignment of the probe cable connector B2
Probe cable-
Probe cable-
Evaluation
MCU
Production
MCU
Evaluation
MCU
Production
MCU
Connector
Pin
Numbers
100
98
Connector
Pin
Numbers
Pin Numbers Pin Numbers
Pin Numbers Pin Numbers
*3
⎯
*3
*4
⎯
*4
13
25
27
28
*4
⎯
⎯
⎯
⎯
*2
*4
31
⎯
⎯
*4
⎯
*4
⎯
⎯
⎯
⎯
⎯
*4
⎯
⎯
⎯
⎯
⎯
*4
⎯
⎯
⎯
51
52
*4
*4
*2
77
79
80
*4
83
86
87
89
94
*4
99
97
95
93
91
89
87
85
83
81
79
77
75
73
71
69
67
65
63
61
59
57
55
53
51
49
47
45
43
41
39
37
35
33
31
29
27
25
23
21
19
17
15
13
11
9
*3
159
217
*3
81
82
83
87
212
*3
86
150
84
272
168
*3
*4
50
14
*4
26
29
⎯
⎯
⎯
*4
⎯
30
⎯
⎯
⎯
*4
⎯
⎯
⎯
⎯
⎯
*4
⎯
⎯
⎯
⎯
⎯
*4
⎯
⎯
⎯
⎯
⎯
*4
⎯
53
54
93
92
*4
78
81
82
84
85
*4
88
95
96
*4
96
94
92
90
88
86
84
82
80
78
76
74
72
70
68
66
64
62
60
58
56
54
52
50
48
46
44
42
40
38
36
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
267
149
260
209
*3
218
263
153
8
*1
*3
5
103
166
*3
151
*3
7
210
261
158
216
*3
157
156
155
88
6
92
266
91
215
*3
16
15
*3
264
213
14
203
*3
299
201
141
110
278
*3
*3
*1
252
71
138
*3
154
255
143
202
142
*3
101
230
262
140
200
*3
199
70
251
198
137
*3
296
136
197
250
135
*3
7
5
3
1
295
64
196
*3
9
SS01-71045-1E
FUJITSU SEMICONDUCTOR • SUPPORT SYSTEM
F2MC-16 Family EMULATOR
QFP-100P PROBE HEADER
MB2147-583
OPERATION MANUAL
May 2005 the first edition
Published FUJITSU LIMITED Electronic Devices
Edited Business Promotion Dept.
|