ZV30RSFSS – GE Monogram 30" Stainless Steel Professional Hood
Dimensions and Specifications (in inches)
Each hood is shipped with a stainless steel backguard and
a warming shelf. Hoods may be installed with the shelf or
backguard alone, or with both as shown.
29-15/16"
12"
Warming
Shelf
22-1/2"
Backguard
29-15/16"
25"
Installation Clearances
These vent hoods are designed to be installed onto a wall or beneath a
Note: Clearances may vary due to type of cooking product and local
codes. Check with local inspectors to be sure standard is applicable.
soffit or cabinet.
Installation with Warming Shelf
• Hoods must be installed 32" Min., 38" Max. over any type cooking
surface when warming shelf is used.
Installation without Warming Shelf
• Install these hoods 30" Min. to 36" Max. above the cooking surface
when installed over any professional style cooktop or range.
• These hoods may be installed 24" min. above a gas or electric
drop-in style cooktop.
Soffit Installation
Wall Mount Installation
SOFFIT
SOFFIT
SOFFIT
SOFFIT
30" Min.
36" Max.
32" Min.
38" Max.
30" Min.
36" Max.
32" Min.
38" Max.
Install these hoods 30" Min. to
36" Max. over a professional
style cooktop or range.
Allow 32" Min. and 38" Max.
clearance above any cooking
surface when installed with shelf.
Install these hoods 30" Min. to
36" Max. over a professional
style cooktop or range.
Allow 32" Min. and 38" Max.
clearance above any cooking
surface when installed with shelf.
In this installation the ductwork running from the top of the hood will
be concealed in the soffit or upper cabinetry.
For this installation, a decorative duct cover is available to conceal the
ductwork running from the top of the hood. Use of the duct cover requires
special consideration to the installation height above the countertop.
®
™
For answers to your Monogram, GE Profile or
GE appliance questions, visit our website at
GEAppliances.com or call
Listed by
Underwriters
Laboratories
R
®
GE Answer Center service, 800.626.2000.
Specification Created 10/02
ZV30RSFSS – GE Monogram 30" Stainless Steel Professional Hood
Using Duct Cover Accessories
To avoid unsightly gaps, plan the hood installation height for duct covers
use. Use the following formula to calculate the need for one of more
duct covers and to ensure a trouble free installation.
We recommend that the vent hood and decorative duct cover (if used)
be on site before final framing and wall finishing. This will help to
accurately locate studs, ductwork and electrical service.
• Read these examples carefully to determine the need for one or more
Ceiling Height
B
6" or 12" duct covers.
A = Countertop to ceiling height.
B = Gap at the top of the hood to the ceiling.
C = Hood installation height – Plus 10" hood height.
10" Hood
Height
A
C
NOTE: Dia. C should be between 40" and 46" (for a 30" to 36" installa-
tion height). Raise or lower the hood installation height to allow use of
one or more 6" and 12" duct covers.
A - B = C
INSTALLATION EXAMPLES
24"
12"
42"
38"
32"
32"
8 ft. ceilings: When the hood is installed 32"
above the cooking surface and there is no
soffit or upper cabinetry, order one 12" and
one 6" duct cover accessory.
9 ft. ceilings: When the hood is installed 38"
above the cooking surface, order two 12" duct
cover accessories.
10 ft. ceilings: When the hood is installed 36"
above the cooking surface, order three 12" and
one 6" duct cover accessories.
®
™
For answers to your Monogram, GE Profile or
GE appliance questions, visit our website at
GEAppliances.com or call
Listed by
Underwriters
Laboratories
R
®
GE Answer Center service, 800.626.2000.
Specification Created 10/02
ZV30RSFSS – GE Monogram 30" Stainless Steel Professional Hood
Features and Benefits
• 640 CFM Vertical Exhaust
• Variable Speed Fan Control
• 2 Halogen Lamps with 4 Lighting Levels
• Infrared Warming Lamp
• Utensil Rod
• Removable Grease Trays
• Removable Stainless Steel Pattern Filters
• Model ZV30RSFSS – Stainless steel
Specification Created 10/02
|