GENNUM Headphones Z 280 User Manual

MULTI-FUNCTION

DIGITAL

WIRELESS

HEADSET

USER'S

MANUAL

Models

Z-280, Z-350, Z-470

L-E-A-P^TMFeature (Model Z-470) . . . . . . 25

Hi-Fi Music Audio Input

(Models Z-350 and Z-470) . . . . . . . . 26

Graphic Equalizer . . . . . . . . . . . . . 27

Minimizing Power Consumption . . . . . . 36

Troubleshooting . . . . . . . . . . . . . . 37

Limited Warranty . . . . . . . . . . . . . 38

Safety Warnings . . . . . . . . . . . . . . 41

Trademarks^TMand Registered Trademarks^®. 41

FCC Notice . . . . . . . . . . . . . . . 42

EU Notice . . . . . . . . . . . . . . . . 43

Specifications . . . . . . . . . . . . . . . 43

Gennum Contact Information . . . . . . . 44

Page 3

Introduction

The Z-E-N^TMModels Z-280, Z-350 and Z-470 headsets use Bluetooth^®

wireless technology to connect to phones or other devices, which support

the headset or handsfree profiles. While connected to your phone (Phone

Mode),you can make and receive calls using the headset,including using voice

control features if your phone supports this function. All models allow the

user to customize the receive phone audio using a 5-band Graphic Equalizer.

In addition, the user is also able to increase the volume level of their

transmitted voice. The Models Z-350 and Z-470 allow the user to plug-in a

PC, CD or MP3 player into the headset to listen to music in between calls and

to use an 8-Band Graphic Equalizer to customize the audio (Hi-Fi Music

Mode). The Model Z-470 adds two L-E-A-P^TM(Local Environment Audio

Processing) Modes (L-E-A-P^TM1 and L-E-A-P^TM2) which allow the user to

carry on face-to-face conversations more easily in noisy environments.

Page 4

Contents of this Package

Z-E-N^TMDigitalWireless Headset

Mini Bag of ReplacementTips

Installation CD

User's Manual

Fitting Guide

Audio Interface Cable

ACWall Charger

Page 5

EAR HOOK

PINCH BUTTON

SIDE BUTTON

BLUE

INDICATOR

LIGHT

EARTIP

Page 6

ROTATE ARM

FOR RIGHT

EAR FIT

FLEXIBLE

ARM

DIGITAL

VOLUME CONTROL

CHARGING PORT /

AUDIO INPUT PORT

Page 7

Storage Position

Rotate the flexible arm upwards into

the upright position as shown in the

photograph for storage.

Cautionary Notes

Significant flexibility has been designed into the flexible arm to allow the

headset to comfortably fit a variety of ear shapes and sizes; however some

care must be taken in manipulating the flexible arm

Failure to observe the following cautionary notes could irreparably damage

your headset and void your warranty

Page 8

NOTE:

Do not attempt to

forcibly rotate the

flexible arm below

the body of the

headset or

NOTE: Only

rotate the

flexible arm

above the

body of the

headset

irreparable

damage will occur

NOTE:

Only stretch

the flexible

arm out

sufficient to

position on

the ear

NOTE:

Do not stretch the flexible

arm out to the position

shown or continuously manipulate the

arm outwards and inwards or

irreparable damage will occur

Page 9

Positioning the Headset

It is recommended you stand in front of a mirror when trying to fit the headset for

the first time. You can fit the headset on either the left ear or right ear by first

rotating the flexible arm over the top of the headset onto the left side or right side

respectively. Grasp the headset between your thumb and index and middle fingers

as shown. Position the body of the headset over the top of the ear and insert the

ear tip into the ear. Rotate the headset until it hooks into position over the top of

your ear. If the ear tip is not snugly positioned in your ear,remove the headset and

adjust the flexible arm by pressing it in the direction that will allow a more snug fit

on the ear. This is just one suggestion for putting it on and you may find a more

convenient way of doing it. We encourage you to try this a few times,in front of the

mirror,until you find the most comfortable position for yourself.

Page 10

NOTE: the arm is made from a flexible rubber material throughout its entire

length and is meant to be adjustable. Please position the arm in the shape desired,

to get the most comfortable fit for you.

PositioningTip

To obtain the best possible results with your headset,it is important to ensure

that the ear tip is inserted snugly into the ear. A snug fit will provide the best

possible sound quality as well as good isolation from external background

noise allowing you to hear the incoming call more clearly. A proper fit can be

obtained by applying pressure to the end of the flexible arm until the ear tip

has provided a good seal in the ear canal,similar to earplugs.

Page 11

Changing the EarTip

With one hand, firmly grasp the end of the ear tip between your thumb and

index finger. Similarly, with the other hand, grasp the end of the flexible arm.

Remove the ear tip with a gentle tug.

To replace the ear tip,reverse this procedure by aligning the hole in the ear tip

and pushing it on the end of the flexible arm until it is firmly seated in position.

Charging the Headset

The headset contains a rechargeable battery and must be charged before

use

Turn the headset off

Insert the headset charging plug into the charging port of the

Page 12

headset

Plug the AC power adapter into an electrical wall outlet

If charging is required, the Blue Indicator Light will turn on indicating

charging is in progress

(if the Blue Indicator Light does not turn on, the headset is already

fully charged)

The Blue Indicator Light will flash when charging is complete

If left plugged-in, the Blue Indicator Light will eventually stop flashing

(Charging is automatically stopped in order to protect your

headset)

Turning On/Off the Headset

To turn ON the headset, press and hold the SIDE button and you will see 2

flashes of the Blue Indicator Light, followed by a longer 3 second flash.

Release the button at any time. If you are wearing the headset,you will hear a

quick series of tones going from low to high pitch. The Blue Indicator Light

will turn off to indicate you have successfully powered on the Z-E-N^TM

headset.

Page 13

To turn OFF the headset, press and hold the SIDE button until you hear 4

beeps. Release the SIDE button and you will hear a quick series of tones going

from high to low pitch. If you are not wearing the headset,press and hold the

SIDE button for 4 flashes of the Blue Indicator Light.

DigitalVolume Control

With the headset oriented upright,

Ÿ Rotate the volume control knob upwards to increase the volume

Ÿ Rotate the volume control knob downwards to reduce the volume

You will hear a beep when you have reached the top end or bottom end of the

volume range.

NOTE: When on a call,the volume control on your headset is synchronized

to the volume on your phone. As you change the volume you will see the

volume bars on your phone change accordingly. However, if you change the

volume control on your phone, it will have no effect on the headset volume

level

NOTE:

The volume control in each mode (Hi-Fi Music, L-E-A-P^TM1,

Page 14

L-E-A-P^TM2 or Phone) is entirely independent so changing the volume in one

mode,will not affect the other modes.

NOTE: Do not initially turn the volume control to maximum until

you become familiar with the volume levels and determine what is

most comfortable for you

Pairing the Headset

You must successfully complete the following pairing procedure to allow the

headset and your phone to communicate. The phone and headset will

remain paired until the pairing is deleted from the phone through the phone

menu options.

? Turn on the Bluetooth function on your phone (refer to your phone's

user manual)

Turn the headset on

? Press and hold the PINCH button until you hear 4 beeps (or 4 flashes if

you are not wearing the headset),then release the button

? Verify that the Blue Indicator Light is solid on, indicating the headset is

now in phone pairing mode

Page 15

Follow your phone's pairing procedure to pair it with the headset

When found,the headset will display as“Z-E-N” on your phone.

When asked for the passkey, password or pin code, enter on

the phone's keypad:0000

? If pairing is successful, your phone will display a “pairing successful”

message and the Blue Indicator Light will turn off. If you are wearing the

headset,you will hear a 'pairing success' melody

? Depending on your phone model, you may have to initiate a

Bluetooth Connection. This can be achieved by selecting 'connect to

Bluetooth device' from your phone or by pressing and holding the

PINCH button for 1 beep, then release the button.

Repeat the pairing procedure if the pairing process fails. If you are

unsuccessful in pairing the headset after several pairing attempts, please

contact Customer Service for assistance.

Multiple Pairings

You can pair the headset with up to 3 phones or devices supporting the

headset or hands-free profile by repeating the pairing procedure described

above. The headset cannot be used with all three devices simultaneously. To

Page 16

move the headset from one device to the next,use the following procedure:

? Turn off the headset

? Turn off the phone or device to which it is currently connected or,turn

off the Bluetooth function,or select“Disconnect Z-E-N” manually from

your phone's menu options

? Turn on the new phone or device you want to now connect with the

headset. You must have previously paired the headset with this phone

or device as described in the pairing procedure

? Turn on the headset

? Depending on your phone model, you may have to initiate a Bluetooth

Connection using the phone. This can be achieved by selecting 'connect

to Bluetooth device' from your phone's menu options (refer to your

phone's user manual), or for some phone models, by pressing and

holding the PINCH button for 1 beep,then releasing the button.

Page 17

FEATURES FOR PHONES SUPPORTINGTHE

BLUETOOTH^®HEADSET PROFILE ONLY

If your phone only supports the Bluetooth Headset Profile,then the following

features are available.

Answering a Call

If your headset is linked to your phone, then with an incoming call, you will

hear a series of ring tones in the earpiece of the headset

? To answer the call,briefly press and release the SIDE button.

Ending a Call

? To end the call,briefly press and release the SIDE button.

Making a Call

? Dial the number you are calling on your phone's keypad and the call will

be automatically transferred to the headset

Transferring a Call

? If you are on an active call using your phone, and then want to transfer

Page 18

the call from your phone to the headset, press and hold the PINCH

button until you hear 1 beep,then immediately release the button

Mute/ Unmute

While on an active call,

? To MUTE the call,briefly press and release the PINCH button. You will

hear 1 beep followed by periodic beeps,indicating the headset has been

muted

? To UNMUTE the call,briefly press and release the PINCH button. The

periodic beeps will stop,indicating that the call has been un-muted

FEATURES FOR PHONES SUPPORTINGTHE

BLUETOOTH^®HANDSFREE PROFILE

If your phone also supports the Bluetooth Handsfree Profile, then additional

features are available.

Answering a Call

If your headset is linked to your phone, then with an incoming call, you will

hear a series of ring tones in the earpiece of the headset

Page 19

? To answer the call,briefly press and release the SIDE button.

If your headset is not linked to your phone,you will not hear the ring tones in

your headset,however you can still transfer the incoming call to your headset

at any time by by pressing and holding the PINCH button for 1 beep. It may

take a few seconds longer to transfer.

Ending a Call

? To end the call,briefly press and release the SIDE button.

Making a Call

If your headset is linked to your phone,

? Dial the number you are calling on your phone's keypad and the call will

be automatically transferred to the headset

If your headset is not linked to your phone, you can still transfer the call to

your headset at any time,

? Press and hold the PINCH button until you hear 1 beep, then

immediately release the button. It may take a few seconds to transfer.

Page 20

Voice Dial

If your phone supports voice-activated dialing and you have set up voice tags

on your phone,

? Press and hold the PINCH button until you hear 1 beep, then

immediately release the button

NOTE: You should create the voice tags from your headset for better

results

Last Number Redial

? Press and hold the PINCH button until you hear 2 beeps, then

immediately release the button

Last Number ReDial while on a Call

? Press and hold the PINCH button until you hear 2 beeps, then

immediately release the button

? Refer to the CallWaiting section below for call control

Rejecting a Call

If you want to reject an incoming call,

? Press and hold the PINCH button until you hear 3 beeps then

Page 21

immediately release the button.

Transferring a Call from the Headset to the Phone

? If you are on an active call using your headset and then want to transfer

the call to the phone,press and hold the PINCH button until you hear 1

beep,then immediately release the button

Transferring a Call from the Phone to the Headset

? If you are on an active call using your phone and then want to transfer

the call to the headset,press and hold the PINCH button until you hear

1 beep, then immediately release the button. There may be a few

seconds delay before the call is transferred

NOTE: This feature may not be supported on all phones and you must use

your phone's menu option to transfer the sound.

CallWaiting

While on an active call and your phone notifies you of another incoming call,

? Press and hold the PINCH button until you hear 1 beep, then

immediately release the button,to accept the waiting call and place the

Page 22

first call on-hold

? Press and hold the PINCH button until you hear 1 beep, then

immediately release the button to swap between an active and a held

call

? Press and hold the PINCH button until you hear 2 beeps, then

immediately release the button, to accept the waiting call and hang-up

the original call

? Press and hold the PINCH button until you hear 3 beeps, then

immediately release the button,to reject the waiting call

? Press and hold the PINCH button until you hear 4 beeps, then

immediately release the button,to release all held calls

Mute/ Unmute

While on an active call,

? To MUTE the call,briefly press and release the PINCH button. You will

hear 1 beep followed by periodic beeps,indicating the headset has been

muted

? To UNMUTE the call, briefly press and release the PINCH button. The

periodic beeps will stop,indicating that the call has been un-muted.

Page 23

Call State

? When you are on a call,the Blue Indicator Light will flash periodically. It

will stop flashing when the call ends

Low Battery State

When the headset requires re-charging, you will hear a warning tone

from your headset. You will receive warnings every minute when 15

minutes of battery time are left. Warnings will increase to every 10

seconds when battery time is 5 minutes or less. When the battery

expires,the unit will power itself off.

To re-charge the headset,

? Turn off the headset

? Refer to the section on Charging the Headset

Error State

? When an invalid button sequence is pressed you will hear a quick low

error beep. This is an indication of an invalid action. No action is taken

and you may continue as usual with your actions.

Page 24

L-E-A-P^TMFeature (Model Z-470 only)

This feature is available while you are not on a call. When you use the L-E-A-

P^TM(Local Environment Audio Processing) feature,you will more clearly hear

the person you are in face-to-face conversation with, because the headset

uses its advanced noise reduction algorithm to minimize the amount of

background noise you hear. Two L-E-A-P^TMmodes are available,namely L-E-A-

P^TM1 and L-E-A-P^TM2. L-E-A-P^TM1, set for normal listening, is factory

programmed to provide a transparent effect which allows the user to

continuously wear the headset without plugging their ear. L-E-A-P^TM2 is set

up to provide additional amplification and noise reduction. L-E-A-P^TM2 has

been designed for challenging noisy environments.

? On initial power-up,you will hear a single beep as the headset defaults to

the L-E-A-P^TM1 mode. Use the volume control to adjust the volume

level into your ear

To turn on the L-E-A-P^TM2 mode, quickly press and release the SIDE

button. You will hear 2 beeps indicating you are in the LEAP 2 mode.

Use the volume control to adjust the volume level into your ear.

? You may toggle between these two modes by quickly pressing and

releasing the SIDE button

Page 25

NOTE: The volume control in each mode (Hi-Fi Music, L-E-A-P^TM1, L-E-A-

P^TM2 or Phone) is entirely independent so changing the volume in one mode,

will not affect the other modes.

When in either of these modes,the user may also customize the audio. Refer

to the section on the Graphic Equalizer.

Hi-Fi MusicAudio Input (Model Z-350 and Z-470 only)

These headset models allow the user to plug in a CD or MP3 music player into

the headset's Charging Port/Audio Input Port using theAudio Interface Cable

provided and listen to hi-fi audio when not on a call. On an incoming call,the

music will be muted to allow the user to hear the ring tones and answer the

call. At the end of the call, the music will be un-muted. To select this mode,

press and hold the SIDE button for 2 beeps,then release. Adjust the volume

level. To exit this mode, press and hold the SIDE button for 2 beeps, then

release.

NOTE: The volume control in each mode (Hi-Fi Music, L-E-A-P^TM1, L-E-A-

P^TM2 or Phone) is entirely independent so changing the volume in one mode,

will not affect the other modes.

Page 26

Refer to the section on the Graphic Equalizer which allows the user to

customize the audio.

Model Z-470 Only

If the user is listening to Hi-Fi Music between calls and needs to conduct a

face-to-face conversation using the L-E-A-P^TMfeature, a quick press and

release of the SIDE button will put the headset into the last selected L-E-A-P^TM

memory. A subsequent quick SIDE button press will continue playing Hi-Fi

music through your headset.

Graphic Equalizer

The graphic equalizer allows you to customize the sound you hear in each

mode of operation: L-E-A-P^TM(Model Z-470 only),Hi-Fi Music (Model Z-350

and Model Z-470) or Phone (all models).

NOTE: Your PC must have Bluetooth^®wireless capability to be able to

use this feature.

Software Installation

Important: Please read the README.txt file on the installation CD:

? Insert the installation CD in the disk drive

Page 27

? Open and read the README.txt file on the CD to ensure your

computer is properly set up for the installation, prior to installing the

Graphic Equalizer software

? After installing the Graphic Equalizer software, a shortcut is created

under the Z-E-N folder which is located in the Start Menu:

Start Menu>Programs>Z-E-N>GraphicEQ>GraphicEQ

? Double click 'GraphicEQ' to start the application

Connecting the Headset for the Graphic Equalizer

Application

? Press the PINCH button and SIDE button simultaneously for 4 beeps

(or 4 flashes of the Blue Indicator Light if you are not wearing the

headset) to place the headset in Graphical Equalizer “Connect

Mode”

? Go to Start->Programs->My Bluetooth Places

? Double-click 'Find Bluetooth Devices'

? Right-click on the Z-E-N Bluetooth device in the Explorer window

? Select “Pair Device”

? During the pairing procedure, when asked for a Password, PIN code

Page 28

or Passkey, enter: 00000000

? Select 'Connect SPP Slave'

? After the pairing procedure is completed, make note of the COM port

value as shown

NOTE: The windows shown above are for theWindows 2000 operating system

and may appear different for other operating systems such as Windows XP,

however the basic procedure remains the same.

NOTE: When the headset has been paired to the PC,you do not have to repeat

the pairing procedure unless you want to pair to another PC. However, you are

required to place the headset in“Connect Mode” (press PINCH and SIDE buttons

simultaneously for 4 beeps) whenever you want to use the Graphic Equalizer

? Click“Connect”

Page 29

? Enter PIN code“00000000” when prompted

Application Setup

? Select the drop down menu next to the 'Connect' button

COM Port Selection

? Click on ‘Set COM Port' and enter the COM port value noted above

? Click 'Update' to save the COM port value

Page 30

? Click 'Connect' to establish a connection to the headset and the

current equalization settings will be displayed

? Click on the appropriate tab (Hi-Fi Music, L-E-A-P^TM1, L-E-A-P^TM2 or

Phone) to select the mode you want to program

Programming the Headset

There are three ways to customize the equalization settings in the

headset:

? Dragging the sliders which programs the setting into the device as

each slider is moved

? Using one of the pre-defined presets which contain default

equalizations settings for different listening environments

? Loading a set of equalization settings that have been previously saved

to a file

NOTE: For each tab, click the 'Defaults' button to return to the factory

programmed settings

Hi-Fi Music Presets (Model Z-350 and Model Z-470)

? Refer to the section on 'Hi-Fi Music Audio Input' on setup for music

listening

? Click the 'Presets' button and a drop down menu will appear

Page 31

? Click on your selection and the equalization settings will be

programmed into the headset. Individual sliders can be changed to

further tune the settings to your liking

Hi-Fi Music Presets

L-E-A-P™ Mode Presets (Model Z-470 only)

? Click the 'Presets' button and a drop down menu will appear

Page 32

? Click on your selection and the equalization settings will be programmed

into the headset

? Individual sliders can be changed to further tune the settings to your liking

L-E-A-P^TMMode Presets

Phone Mode Programming and Presets

Phone Mode Programming

To listen to changes that you have programmed in Phone mode:

Page 33

? Connect the Audio Interface Cable to the Z-E-N^TMheadset and to

the PC audio port

? Ensure the volume level on the PC is not muted

? Click the 'Play Test Call' button and you will hear the test call audio.

? If necessary, increase the volume level on your PC

? You can dynamically change the settings while the Test Call is playing

Phone Mode

Page 34

NOTE: A Microphone Gain slider is also available which controls the

loudness level of your voice heard by the person you are talking with on

the phone. Adjust this setting only if your called party complains that your

voice is not loud enough. Adjusting this level too high will make your voice

sound distorted and/or the person you are talking with may hear an echo

of their voice

Phone Mode Presets

? Click the 'Presets' button and a drop down menu will appear similar

to the L-E-A-P^TMmode presets

? Click on your selection and the equalization settings will be

programmed into the headset

? Individual sliders can be changed to further tune the settings to your

liking

Customizing, Saving and Loading Equalization Settings

For each tab selection, you may customize and save the equalization

settings as follows:

? Select the tab for adjustment: Hi-Fi Music, L-E-A-P^TM1, L-E-A-P^TM2 or

Phone

Page 35

? Drag the sliders into the positions you prefer

? Click the 'Save' button and save the file with a .zen extension. You

may save as many files as you like.

? To load a previously saved file, click the 'Load' button and browse for

the file you want to load

Disconnecting the Z-E-N^TM

There are two ways to disconnect from the headset:

? Clicking 'Disconnect' will disable the connection to the headset.

? Clicking 'Close' will disconnect the connection to the headset and

close the Graphic Equalizer application.

Minimizing Power Consumption

Switch off the headset if you anticipate you will not be using the headset for an

extended period of time and if convenient, connect it to the charger so the

headset is always fully charged and ready for use.

Page 36

TROUBLESHOOTING

The phone or headset does not respond at all when I press

the SIDE or PINCH buttons?

You may need to reset your phone by turning off the power and then turning it

back on again. You may also need to turn the Z-E-N^TMheadset off and then

back on. All button presses on the headset are accompanied by a flash of the

Blue Indicator Light. If you don't see a flash, this is a definite indication of a

dead battery.

Does your caller complain they hear an echo?

Generally this is an indication that the ear tip is not positioned snugly in the

ear and the phone volume is high. Try re-positioning the ear tip until a better

seal is obtained and/or reducing the call volume.

Is the incoming sound tinny and quiet?

Try re-positioning the ear tip into the ear for a better seal which will restore

proper volume and tonal balance to the incoming audio.

Page 37

Limited Warranty

Gennum Corporation warrants that your headset will be free from defects in

material or workmanship for a period of one (1) year from the date of

shipment,under normal use and conditions.For all warranty and service

related matters, please see the Gennum Contact Information on

the last page of this manual.

During this period, if the headset is found to be defective in materials or

workmanship,Gennum will repair or replace it,at the sole option of Gennum,

at no charge to you.If Gennum determines that it is not possible to repair or

replace the headset, it may, at its sole option, refund the purchase price paid

for the headset. THESE ARETHE SOLE AND EXCLUSIVE REMEDIES FOR

BREACH OF WARRANTY BY GENNUM. IN NO EVENT SHALL

GENNUM BE LIABLE FOR DAMAGES EXCEEDINGTHE SALE PRICE FOR

YOUR HEADSET.

You are responsible for packing the defective headset properly in the original

packaging,and for the cost of shipping. A copy of the original receipt must be

included. Shipping instructions will be given by technical support at Gennum.

Page 38

Warranty repairs are completed at no charge for parts or labour, and

Gennum will pay the cost of shipping the repaired or replaced product back

to you.Warranty repairs may use new or equal replacement parts. Goods will

not be accepted for return for non-warranty reasons without the express

prior written approval of Gennum.

Gennum reserves the right to make the final decision on any warranty claim

that may be questionable. This limited warranty does not cover and Gennum

will not be responsible for failures or defects due to misuse, neglect, abuse,

accidents, alterations, improper or unauthorized installation or service,

unauthorized removal or repairs, failure to follow instructions, fire, floods,

acts of God,or spills of food or liquids.

EXCEPT FOR THE EXPRESS LIMITED WARRANTY PROVIDED ABOVE,

THE HEADSET, FIRMWARE, SOFTWARE, WALL CHARGER WITH

ADAPTERS, REPLACEMENT EAR TIPS AND WRITTEN MATERIALS ARE

PROVIDED “AS IS” WITHOUT REPRESENTATION, CONDITION OR

WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED OR

STATUTORY,AND GENNUM SPECIFICALLY EXCLUDESALL OTHER

CONDITIONSANDWARRANTIES,INCLUDING BUT NOT LIMITEDTO

Page 39

IMPLIED CONDITIONS AND WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL

GENNUM BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR

CONSEQUENTIAL DAMAGES ARISING DIRECTLY OR INDIRECTLY IN

CONNECTION WITH THE HEADSET,THE USE OF THE HEADSET OR

OTHERWISE,WHETHER FOR LOSS OF PROFITS, BUSINESS REVENUES

OR OTHERWISE.

This warranty sets forth the entire responsibility of Gennum with respect to

the headset,firmware,and software,wall charger with adapters,replacement

tips and written materials. Your exclusive remedy is repair, replacement or

refund as stated herein.In no event shall Gennum's liabilities exceed the cost

of correcting defects as provided herein and any such liabilities will terminate

upon expiration of the warranty period.

This warranty is valid only when the headset is purchased from a Gennum

Authorized Dealer,and applies only to the original purchaser. Headsets with

the serial number or model designation removed,altered,replaced or defaced

are not covered by this warranty.

Page 40

SafetyWarnings

This package contains small parts which may be hazardous to children under

Headsets encourage hands-free operation of phones while driving or

conducting other activities. You should nonetheless ensure you obey the laws

regarding cell-phone use while driving, and give your full attention to the

operation of your vehicle.

Do not attempt to use this device if it is submerged in liquid. Immediately

unplug all electrical connections.

Users with pacemakers or other electrical medical devices should consult

with their physicians before using cell-phones or a headset.

The use of wireless devices and their accessories may be prohibited or

restricted in certain areas.Always obey the laws and regulations on the use of

these products.

Trademarks™ and RegisteredTrademarks ®

The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc.

Page 41

and any use of such marks by Gennum Corporation is under license.

The Z-E-N^TMand L-E-A-P™ trademarks are owned by Gennum Corporation.

FCC Notice

This device contains FCC ID SD7GR2316 which complies with part 15 of the

FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,and

(2) This device must accept any interference received, including

interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

Please refer to the zen.gennum.com website for more information.

Page 42

EU Notice

DECLARATION OF CONFORMITY

In accordance with Annex IV of the EU directive 1999/5/EC, Gennum

Corporation declares under our responsibility that the product:

Type:

Intended Purpose:

Equipment Class:

Z-280,Z-350,Z-470

Bluetooth Headset

complies with the appropriate essential requirements of the Article 3 of the

R&TTE and the other relevant provisions,when used for its intended purpose.

Please refer to the zen.gennum.com website for more information.

Specifications

TypicalWeight

22 grams

TypicalTalkTime

8 hours

Typical StandbyTime

Typical RechargeTime

100 hours (from a full charge)

2 hours (from a full discharge)

Design and specifications are subject to change without notice.

Page 43

Gennum Contact Information

For latest revisions to this manual, customer assistance or inquiries about the

Z-E-N^TMheadset,please visit our website at

zen.gennum.com

For general inquiries,please e-mail us at

[email protected]

CorporateAddress:

Gennum Corporation

970 Fraser Drive, Burlington, Ontario L7L 5P5

www.gennum.com

ZEN350series 2.0

Earthquake Sound Speaker Kompressor User Manual
Educational Insights Video Games EI 7924G User Manual
Essick Air Humidifier ED11 800 User Manual
EverFocus Security Camera EZ600 B User Manual
Everpure Water System ESO 6 User Manual
Fisher Price Automobile Parts 73180 User Manual
Fisher Price Baby Accessories M5598 User Manual
Fisher Price Riding Toy H4088 User Manual
GE Monogram Dishwasher ZBD3000 User Manual
Global Technology Associates Network Card GB 800 User Manual