Grundig Flat Panel Television 46 VLE 6220 BF User Manual
LCD TV  
46 VLE 6220 BF  
EN  
 
Contents--------------------------------------------------------------------------------------------------------------------------------------  
43- speCiAl-settinGs  
44 Searching for digital terrestrial  
TV channels automatically  
-
45 Searching for digital terrestrial  
TV channels manually  
46 Tuning analogue television channels  
47 Changing stored analogue channels  
49- inFormAtion  
-
49 Displaying signal information  
49 Service information for retailers  
49 Environmental note  
50 Technical data  
51 Troubleshooting  
52 Additional Information for units sold in the  
UK  
-3  
ENGLISH  
 
setup-AnD-sAFetY-------------------------------------------------------------------------------------------------------  
7
Please note the following instructions when  
setting up the television set:  
Make sure the power cord or the power sup-  
ply unit (if provided) are not damaged.  
7
7
7
This television is designed to receive and dis-  
Only operate the television with the power  
supply/power cord provided.  
play video and audio signals.  
All other uses are expressly prohibited.  
Thunderstorms are a danger to all electrical  
devices. Even when the television is switched  
off, it can be damaged by a lightning strike to  
the mains or the antenna. Always disconnect  
the mains and antenna plugs during a storm.  
7
The ideal viewing distance is five times the  
diagonal screen size.  
7
Light falling on the screen impairs picture  
quality.  
7
7
Use a damp, soft cloth to clean the screen.  
Do not use water with soap or detergent.  
7
To ensure the device is always adequately  
ventilated, make sure there is sufficient space  
between the television set and nearby furniture  
(min 10 cm).  
Only clean the housing of your television set  
with the cloth provided. Do not use water with  
soap or detergent.  
7
The television is designed for use in dry rooms.  
7
If you do use it outdoors, make sure it is pro-  
tected from moisture such as rain or splashing  
water.  
When deciding where to put the device, re-  
member that furniture is often coated with vari-  
ous types of varnish and plastic. Many of these  
contain chemicals which can corrode the feet  
of the device, leaving marks on the surface of  
the furniture which can be difficult or impossi-  
ble to remove.  
Never expose the television set to moisture.  
7
Do not place any vessels such as vases on the  
television, as they may spill liquid, thus present-  
ing a safety risk.  
7
The screen of your LCD television meets  
the highest quality standards and has been  
checked for pixel faults.  
Despite the great care taken in manufacturing,  
technological reasons make it impossible to  
completely discount the possibility that some  
pixels may be faulty.  
Provided they are within the thresholds speci-  
fied by the DIN norm, pixel faults of this kind  
cannot be regarded as a defect as defined by  
the warranty.  
7
Place the television on a hard, level surface.  
7
Do not place any objects such as newspapers  
on the television or put cloth or similar items  
under it.  
7
Do not place the television close to heating  
units or in direct sunlight, as this will impair  
cooling.  
7
Heat build-up can be dangerous and shortens  
the service life of the television. For reasons of  
safety, have a repairman remove any dirt in  
the television from time to time.  
7
To ensure fires do not occur,  
always keep candles and other  
open flames away from the device.  
7
Never open the television under any circum-  
stances. Warranty claims are excluded for  
damage resulting from improper handling.  
-4  
ENGLISH  
 
setup-AnD-sAFetY-------------------------------------------------------------------------------------------------------  
7
Do not connect any other equipment while the  
device is switched on. Also switch off other  
equipment before connecting it.  
7
Do not plug in the power cord of the device  
until you have connected the external equip-  
ment and the antenna.  
7
To avoid safety problems arising from the bat-  
teries used with the product, follow the instruc-  
tions below.  
7
In case of misplacement of batteries, they may  
cause explosion due to short circuit.  
7
Do not expose the batteries to excessive heat  
such as direct sunlight, fire, etc.  
7
Do not use old and unused batteries together.  
7
Only replace the exhausted batteries with  
those having the same model, value and prop-  
erties.  
7
To avoid environmental health problems aris-  
ing from the product, batteries and accesso-  
ries.  
7
Make sure the mains plug is freely accessible.  
Caution:  
7
If you plan on using a wall bracket for your  
television, make sure you read the assembly  
manual for the wall bracket or have a spe-  
cialist assemble it.  
7
When purchasing the wall bracket, make  
sure that all the fastening points on the televi-  
sion are also on the wall bracket and that  
they are all used when mounting it.  
-5  
ENGLISH  
 
GenerAl-inFormAtion----------------------------------------------------------------------------------  
receiving-digital-channels  
You require a digital roof antenna or indoor  
antenna (passive or active indoor antenna  
with its own power supply) to receive digital  
television channels (DVB-T).  
special-features-of-your-  
-television-set  
You can receive and watch digital TV channels  
using your television set (via DVB-T and DVB-C)  
– including High Definition programmes (HD).  
However, the reception of digital TV channels  
in HD is currently limited to a few countries in  
Europe.  
7
7
7
If you wish to receive digital television chan-  
nels via your cable system (DVB-C), the an-  
tenna cable for your cable operator must be  
connected to the television set.  
7
Although this television set complies with the  
current DVB-T and DVB-C standards (status:  
August 2010), the compatibility with future ter-  
restrial DVB-T and DVB-C cable programmes  
cannot be guaranteed.  
7
Unlike analogue broadcasting, not every  
channel has its own transmission frequency.  
Instead, several channels are grouped into  
what are known as bouquets on a regional or  
national level. You can find the current trans-  
mission information on teletext from various  
broadcasters, or by consulting a current TV  
guide or the Internet.  
7
Your television set can receive and process  
all analogue and non-encrypted digital  
TV channels. The television set is also equipped  
with digital and analogue receivers.  
7
Various digital television channels from private  
7
The electronic TV guide (for digital channels  
broadcasters are encrypted (DVB-T and DVB-  
C). Watching these channels and the record-  
ing and playback functions are only possible  
with the appropriate CI module and a Smart-  
Card. Ask your specialist dealer.  
only) informs you about any schedule changes  
at short notice, and provides an overview of  
all the broadcasters' schedules for the next few  
days. Detailed information on the individual  
television programmes are – when provided  
by the broadcasting station – are also avail-  
able in the electronic TV guide.  
The range of channels available from the pub-  
lic broadcasting institutions (ARD with EinsEx-  
tra, EinsFestival or ZDF with ZDF Info and all  
third party broadcasters) are not encrypted  
and can be received without a SmartCard.  
7
You can connect various data media, such as  
an external hard drive, a USB memory stick or  
a digital camera, to the USB socket. Using the  
file browser, you can then select and play the  
file formats of your choice (for example, MP4,  
MP3 or JPEG data).  
-6  
ENGLISH  
 
GenerAl-inFormAtion----------------------------------------------------------------------------------  
important-notes-on-  
environmental-protection  
7
The following information will help you to save  
resources – and money as well.  
7
If you are not using your television set for  
several days, you should pull out the mains  
plug for environmental and safety reasons.  
This way the television does not consume any  
electricity.  
7
As switching off the television set does not  
completely disconnect it from the mains, pull  
out the plug to disconnect it from the mains  
completely.  
7
If the device is equipped with a power switch,  
switching it off using this switch will be suffi-  
cient. The energy consumed by the television  
set is reduced to virtually 0 W.  
7
In standby mode, the television set uses very  
little energy. However, it may be necessary to  
leave the television set in standby mode for cer-  
tain functions (for example automatic switch-on  
and switch-off and for timer functions).  
7
The television set uses less energy when the  
brightness is reduced.  
-7  
ENGLISH  
 
ConneCtion-AnD-prepArAtion------------------------------------------------  
Connecting-the-antenna-and-power-cord  
2
1
1a To receive terrestrial digital broadcasters  
(DVB-T) connect the cable for the rooftop  
or indoor antenna (passive or active indoor  
antenna with its own power supply) to the an-  
tenna socket »Ant-in« on the television set;  
2
Plug the power cord into a wall socket.  
note:  
7
Do not plug in the power cord of the device  
until you have connected the external equip-  
ment and the antenna.  
or  
7
Only use the power cord supplied to connect  
1b To receive digital cable channels (DVB-C)  
connect the cable for the rooftop antenna  
to the antenna socket »Ant- in« on the  
television set;  
the television set to a suitable earthed safety  
socket.  
7
Do not use an adapter plug or extension  
lead which does not meet the applicable  
safety standards. Do not tamper with the  
power cord.  
or  
1c To receive analogue TV channels, connect  
the cable for the rooftop antenna to the an-  
tenna socket »Ant-in« on the television set  
note:  
7
When connecting an indoor antenna you  
may have to try it out at different positions  
until you get the best reception.  
-8  
ENGLISH  
 
ConneCtion-AnD-prepArAtion------------------------------------------------  
environmental-note  
inserting-batteries-into-the-  
-remote-control  
7
This symbol on recharge-  
able batteries/batteries  
or on the packaging indi-  
cates that the rechargea-  
ble battery/battery may not be disposed of  
with regular household rubbish. For certain  
rechargeable batteries/batteries, this sym-  
bol may be supplemented by a chemical  
symbol. Symbols for mercury (Hg) or lead  
(Pb) are provided if the rechargeable batter-  
ies/batteries contain more than 0.0005%  
mercury or more than 0.004% lead.  
Rechargeable batteries/batteries, including  
those which do not contain heavy metal,  
may not be disposed of with household  
waste. Always dispose of used batteries  
in accordance with local environmental  
regulations. Make enquiries about the appli-  
cable disposal regulations where you live.  
1
2
Open the battery compartment by removing  
the lid.  
Insert the batteries (2 x 1.5 V micro, for  
example R03 or AAA). Observe the po-  
larity marked in the bottom of the battery  
compartment.  
3
Close the battery compartment.  
note:-  
7
If the television no longer reacts properly  
to remote control commands, the batteries  
may be flat. Always remove used batteries.  
7
The manufacturer accepts no liability for  
damage caused by leaking batteries.  
-9  
ENGLISH  
 
overview-------------------------------------------------------------------------------------------------------------------------------------  
Connections-on-the-television-set  
Av1-/-s-vhs  
SCART socket (CVBS signal,  
RGB signal);  
Video and sound socket for  
S-Video camcorder.  
optic-out  
Socket for audio output  
(optical) for PCM/AC3  
signals.  
For connecting digital AV  
amplifiers or AV receivers.  
Component  
Audio  
pC-in  
Socket for audio  
input for a PC.  
---pb-pr-Y/Av2 Sockets for video input  
(YUV signal).  
l--r  
Sockets for audio input  
VGA socket, video input  
for PC.  
(YUV signal);  
Audio socket for  
camcorder.  
Ant-in  
Antenna socket for a DVB-T,  
DVB-C and analogue  
antenna.  
Y/Av2-  
-Video socket for  
camcorder  
-10  
ENGLISH  
 
overview-------------------------------------------------------------------------------------------------------------------------------------  
hDmi2  
hDmi3  
U
HDMI socket,  
Controls-on-the-television-set  
audio/video input.  
8/i-  
Switches the television on and  
back into standby mode.  
HDMI socket,  
audio/video input.  
v–--v+  
menu-  
Adjusts the volume;  
Headphone jack (3.5 mm  
jack plug);  
Sockets for audio output.  
selects menu functions.  
-Opens the menu.  
Select a menu option with  
»p+« or »p–«.  
usB  
-USB socket for external  
data media.  
Activate the function with  
»v+«.  
hDmi1  
Ci- -  
HDMI socket,  
audio/video input.  
Confirm the function with  
»v+« or »v–«..  
Press »menu« to quit the menu.  
-Common Interface Slot.  
sourCe- Opens the pre-selection for  
AV channels.  
In the menu, press »p+« or »p–«  
to select and press »sourCe« to  
confirm.  
p–--p+  
Switches the television on from  
standby;  
selects channels in steps;  
selects function in the menu.  
-11  
ENGLISH  
 
overview-------------------------------------------------------------------------------------------------------------------------------------  
the-remote-control-–-main-functions  
Switches on from standby;  
Selects channel – directly  
Switches on and off  
(Standby).  
Selects the channel list  
(»All«, »FAV 1« to »FAV 4«).  
Switches between  
teletext and TV mode.  
Opens the selection menu to  
change picture formats.  
Opens the »HDMI CEC De-  
vice List«.  
Then select with » « or » «  
<
>
and press »oK« to confirm.  
Displays information.  
-Zapping function;  
switches back one menu  
level in the menus.  
Opens the main menu  
-Opens the channel list.  
Opens the electronic  
TV guide.  
Opens the TOOLS menu.  
Adjusts the volume.  
Opens menu for AV channels  
and USB input.  
Then select using »  
v«, » «,  
<
» « or » « and press »oK«  
Λ
>
to confirm.  
Muting  
Switches on from standby;  
Selects channel – in steps.  
navigation-in-the-menus  
Moves the cursor up  
and down in the menus.  
-
right in the menus.  
-Activates various functions and  
save functions/settings.  
-12  
ENGLISH  
 
overview-------------------------------------------------------------------------------------------------------------------------------------  
the-remote-control-–--  
All-functions  
Selects different subtitles  
(only for digital television chan-  
nels)  
» «-(red)-  
Selects pages in teletext;  
Selects/activates various  
Selects different audio lan-  
guages (only for digital televi-  
sion channels)  
»
»
»
« (green)  
  
« (yellow) functions in the menus.  
  
  
« (blue)  
Key has no function.  
8
Starts playing a programme  
from an external data medium.  
!
7
Freeze frame;  
Playback pause from an exter-  
nal data medium.  
Ends playback of a pro-  
gramme from an external data  
medium;  
Splits the screen in teletext.  
5
Switches to double character  
size in teletext;  
Selects the next title/next pic-  
ture in the file browser.  
6
Refreshes a teletext page;  
Selects the previous track/pre-  
vious picture in the file browser.  
3
Stops scrolling through pages  
in teletext;  
Starts a fast reverse search in  
the file browser.  
4
Reveals answers in teletext;  
Starts a fast forward search in  
the file browser.  
-13  
ENGLISH  
 
settinGs------------------------------------------------------------------------------------------------------------------------------------------  
selecting-language,-country-and-  
operating-mode  
initial-set-up-and-tuning-  
-television-channels  
The television set is equipped with automatic  
channel search, which searches for terrestrial  
channels (DVB-T), cable channels (DVB-C) and  
analogue channels.  
1
Switch on the television set from standby with  
»8«, »1…0« or »p+« or »p-«.  
– During initial set-up, the »Installation Guide«  
will be displayed.  
You start the search and can then copy the tel-  
evision channels into four favourite lists and sort  
them there into your order of preference.  
help:-  
7
If this menu is not displayed, restore the  
television set to its default settings (see  
page 34).  
For DVB-T and DVB-C channels 1000 presets,  
and 100 presets for analogue channels.  
2- Select the menu language with » «, » «,  
<
>
»v« or »  
Λ« and press »oK« to confirm.  
the-various-settings  
3- Select the mode with » « or » « and press  
<
>
Depending on the type of antenna connected,  
you can decide which channels you would like  
the television to search for.  
»oK« to confirm.  
– The settings used in »Home Mode« help to  
save energy.  
7
Tunes digital terrestrial television channels, on  
page 15.  
– Alternatively, the menu item »Shop Mode«  
can be selected which the retailer can use  
for demonstrating the device functions.  
7
Tunes digital television channels from the  
cable provider, on page 15.  
note:  
7
End the »Shop Mode« by restoring the tel-  
7
Tunes analogue television channels, in the  
evision set to its default settings (see page  
34).  
chapter “Special functions”, starting on page  
46.  
4- Select the country in which the television set  
7
Further settings for digital television channels  
is operated with » «, » «, »v« or »Λ« and  
<
>
after the initial set-up can also be found in the  
chapter “Special functions”, starting on page  
43.  
press »oK« to confirm.  
– The »Source Setup« menu appears with the  
»Connection Type« line marked.  
note:-  
note:  
7
Make the language and country selection for  
all types, then continue reading the respective  
chapter.  
7
You can find a description of how to tune  
the television channel of your choice – de-  
pending on the antenna connected – in the  
following chapters.  
-14  
ENGLISH  
 
settinGs------------------------------------------------------------------------------------------------------------------------------------------  
tuning-terrestrial-television-  
channels-(DvB-t)  
tuning-television-channels-from-  
the-cable-provider-(DvB-C)  
1
In the »Source Setup« menu, in the »Connec-  
tion Type« line, select the option »Cable«  
with » « or » «.  
1
In the »Source Setup« menu, in the »Connec-  
tion Type« line, select the option »Air« with  
» « or » «.  
<
>
<
>
2
Select the line »Scan Type« with »  
«.  
Use » « or » « to set the required scan  
v« or  
2
Select the line »Scan Type« with »  
«.  
Use » « or » « to set the required scan  
v« or  
»Λ  
»Λ  
<
>
<
>
type:  
type:  
– »DTV«, scan for digital television channels;  
– »ATV«, scan for analogue television  
channels;  
– »DTV«, scan for digital television channels;  
– »ATV«, scan for analogue television  
channels;  
–
»ATV & DTV«, scan for analogue and  
digital television channels.  
–
»ATV & DTV«, scan for analogue and  
digital television channels.  
3
Select the line »Cabel Scan Type« with »  
or » «. Select the preferred option (»Quick«  
or »Full«) with » « or » «.  
– The search function »Quick« sets up the  
channels according to the information pro-  
vided by your cable provider in the trans-  
mission signal.  
v«  
Caution:  
Λ
7
The antenna power supply (5V ) may only  
<
>
be switched on if the antenna is an active  
indoor antenna with a signal amplifier and it  
is not already supplied with a voltage via a  
mains plug (or similar supply). Otherwise  
you may cause a short circuit and irrepara-  
bly damage your antenna.  
– If the option »Full« is selected, the entire  
frequency range will be scanned. The  
search can take a long time with this op-  
tion. This option is recommended if your  
cable provider does not support the scan  
3
4
Select the line »Active Antenna Power« with  
»
v
«
or »Λ«.  
Switch on the antenna power supply for the  
antenna with » « or » « (»On«).  
<
>
  
type  
»Quick«.  
Start the scan with » « (green).  
note:  
– The »Search Results« menu appears, and  
the search for TV channels begins.  
– Depending on the number of television  
channels received, this can easily take a  
few minutes.  
7
You can accelerate the search. To do this,  
you need information about the frequency  
and network ID. You are usually able to get  
this data from your cable operator or find it  
in forums on the Internet.  
– The scan is complete as soon as the »PRO-  
GRAM TABLE« appears.  
4
Start the scan with » « (green).  
  
–
The »Search Results« menu appears, and  
the search for TV channels begins.  
note:  
7
You can abort the scan by pressing  
»menu«.  
– Depending on the number of television  
channels received, this can easily take a  
few minutes.  
– The scan is complete as soon as the »PRO-  
GRAM TABLE« appears.  
5
Press »menu« to end the setting.  
note:  
7
You can abort the scan by pressing  
»menu«.  
5
Press »menu« to end the setting.  
-15  
ENGLISH  
 
settinGs------------------------------------------------------------------------------------------------------------------------------------------  
selecting-channel-lists  
Changing-the-program-table-for-  
the-digital-channels  
1
Open the menu with »menu«.  
Channels which are found using the scan are  
saved in the »PROGRAM TABLE«.  
2
Select the »SOURCE SETUP« menu with »v«  
or »Λ« and press »oK« to confirm.  
– The »SOURCE SETUP« menu appears.  
You can delete channels which are not required  
from the programe table, and lock individual  
channels (Parental control).  
3
Select the line »Programe Table« with »v«  
or »Λ« and press »oK« to confirm.  
– The menu »PROGRAM TABLE« appears.  
You can also add channels to the favourites list;  
in addition, you can change the order of chan-  
nels within the favourites list.  
important:  
7
Programe table and favourites lists are  
saved separately according to the different  
input sources (cable and air).  
With » « (green) you can display the channels  
  
which belong to one network.  
7
When opening the programme table, the  
respective channel list for the current input  
signal appears.  
Switch to the next page in the programe table  
with »p+« and to the previous page with »p-«.  
With »  
« (yellow) you can open the »LIST  
  
note:  
MANAGEMENT« within the programe table.  
In this List Management you can create your  
own favourites lists.  
7
If in the Program Table  
appears added  
to the name of the channel, you need a  
CI module and a Smart-Card for watching  
these channals.  
INSTALLATION  
PROGRAM TABLE  
Network ALL  
1
Das Erste  
Service  
ALL  
DTV  
RADIO  
DATA  
ATV  
2
ZDF  
3
SAT1  
4
N24  
3sat  
5
SAT3  
1 Das Erste  
DTV  
DTV  
DTV  
DTV  
DTV  
6
24  
7
HD Sport  
8
HD Test  
9
10 RTL  
DTV  
DTV  
DTV  
DTV  
DTV  
11 HD 1  
12 Life  
13 Film  
14 Promo  
15 Sport1  
DTV  
DTV  
DTV  
DTV  
DTV  
16 TV Sport  
17 Sat.8  
18 SKY  
19 TV6  
20 TV5  
DTV  
DTV  
DTV  
DTV  
DTV  
Edit  
Network  
Manage lists  
Sorting  
Exit  
Select favourites  
Back  
-16  
ENGLISH  
 
settinGs------------------------------------------------------------------------------------------------------------------------------------------  
notes:  
Creating-lists-of-favourites  
You can save your favourite channels in up to  
four favourites lists (FAV 1 to FAV 4).  
7
Repeat steps 2 and 3 if you would like to  
change other channels within the same  
favourites list.  
notes:  
7
Repeat steps 1 to 3 if you would like to  
change channels in a different favourites list.  
7
Favourites lists must be created separately  
for all input sources (cable and air).  
4
Exit the current favourites list with »  
(blue).  
– The entire programe table will appear  
again.  
«
  
7
You can select the favourites list by pressing  
»FAv«.  
1
2
3
In the »PROGRAM TABLE« menu, switch over  
to the list view with » « (yellow).  
  
Deleting-channels  
1
Select the channel of your choice with »  
or »Λ«.  
v«  
In the »PROGRAM TABLE« menu, select the  
television channel to be deleted with «,  
» « or » « and press » «- (red) to  
»
v
“Push” the channel into the favourites  
»
Λ«,  
<
>
lists 1 to 4 with » « or » « and press »oK«  
<
>
activate.  
to confirm.  
– The position in the favourites list is marked  
with »✔«.  
2
3
4
Deletethecurrentchannelwith» «(yellow);  
  
« (blue).  
delete all channels with »  
  
– You can enter the same channel in more  
than one favourite list.  
– Each favourite list can store up to 255  
channels.  
Confirm the deletion process with »  
(green).  
«
  
Quit the deletion process with » «.  
<
note:  
skipping-channels  
You can mark television channels which should  
be skipped when selecting with » « or » «.  
It is still possible to select them using the number  
buttons.  
7
Channels can also be deleted from the  
favourites lists. Select the channel to be  
Λ
v
deleted with »  
v«, »Λ«, » « or » « and  
<
>
press »oK« to delete it.  
7
When deleting a channel from the favourites  
list, the order within the favourites list will be  
updated.  
1
2
3
In the »PROGRAM TABLE« menu, switch over  
to the list view with » « (yellow).  
  
Select the preferred channel with »  
or » «.  
v«  
4
Press »menu« to end the set-up.  
Λ
sorting-channels-in-the-favourite-list  
You can change the order of channels in the  
favourites list.  
Select the column »Skip« with » « or » «  
and use »oK« to mark the channel.  
– The channel is marked by »✔«.  
<
>
1
In the »PROGRAM TABLE« menu, select the  
favourites list »1« to »4«.  
note:  
7
Channels can also be reactivated. Select the  
channel with » « or » «, then select the  
column »Skip« and reactivate the channel  
with »oK«  
2- Select the channel which should be moved  
with » «, » «, » « or » « and mark it with  
» «-(red).  
v
Λ
v
Λ
<
>
.
3
Move the channel to its new position with  
«, » «, » « or » « and press »oK« to  
confirm.  
»
v
Λ
<
>
-17  
ENGLISH  
 
settinGs------------------------------------------------------------------------------------------------------------------------------------------  
notes:  
picture-settings-  
7
You can only select the »Mpeg NR« function  
1
Open the menu with »menu«.  
on digital and AV presets.  
2
Select the menu item »PICTURE SETTINGS«  
»Mpeg NR« reduces any interference from  
artefacts (pixel blocks) from digital pro-  
grammes due to MPEG compression (such  
as from DVB-T receivers or DVD players).  
The »Film Mode« detects and processes  
feature films automatically for all channel  
sources. This means you will always receive  
an optimal picture.  
This functions in the modi 480i, 576i and  
1080i in TV playback and for other channel  
sources.  
If the »Film mode« is switched on for pro-  
grammes without a feature film signal, minor  
problems such as picture freeze, defective  
subtitles or fine lines in the picture could  
occur.  
The function »Dynamic Contrast« adapts the  
contrast dynamically and optimally for the  
respective picture content.  
With »Dynamic Backlight«, the device opti-  
mally adapts the background lighting to the  
picture content.  
The »Backlight« can only be set manually  
when the function »Dynamic Backlight« is  
deactivated.  
»MEMC« will only appear in menus of LCD  
products with 200 Hz PPR Feature and LED  
products with 400 Hz PPR feature..  
with »v« or »Λ« and press »oK« to confirm.  
– The »PICTURE SETTINGS« menu appears.  
20.09.2010  
15:46  
PICTURE SETTINGS  
7
Picture Mode  
Brightness  
Contrast  
User  
50  
100  
Sharpness  
Colour  
75  
65  
Colour Temperature  
Medium  
Enhanced picture settings  
DNR  
Off  
Off  
7
7
7
7
Mpeg NR.  
Exit  
Back  
3
Select the line »Picture Mode«, »Bright-  
ness«, »Contrast«, »Sharpness«, »Colour«, or  
»Colour Temperature« with »v« or »Λ«.  
Select the value with » « or » « and press  
<
>
»oK« to confirm.  
notes:  
7
When changing the values with » « or  
<
5
Press »menu« to end the setting.  
» «, the screen will be split. You can see  
>
the current setting on the left side, the new  
setting on the right side.  
7
In the »PICTURE SETTINGS« menu you can  
also find other additional settings.  
4
Select the line »DNR«, »Mpeg NR«, »Vibrant  
Colour«, »Perfect Clear«, »Film Mode«,  
»Gamma«, »Dynamic Contrast«, »Dynamic  
Backlight«, »Backlight« or »MEMC« with  
»
v« or »Λ«.  
Select the value with » « or » « and press  
<
>
»oK« to confirm.  
-18  
ENGLISH  
 
settinGs------------------------------------------------------------------------------------------------------------------------------------------  
Automatic-volume  
sound-settings-  
Television stations broadcast at different vol-  
umes. The automatic volume limiting (AVL) func-  
tion means the volume is kept the same when  
you switch between channels.  
1
Open the menu with »menu«.  
2
Select the menu item »SOUND SETTINGS«  
with »v« or »Λ« and press »oK« to confirm.  
– The »SOUND SETTINGS« menu appears.  
1
Select the line »AVL« with »  
v« or »Λ« and  
20.09.2010  
15:46  
select the option »On« with » « or » «.  
<
>
SOUND SETTINGS  
note:  
7
If the »SRS TS HD« setting has been selected  
in the »Audio Mode« line, the AVL line can-  
not be selected.  
Volume  
10  
Balance  
AVL  
Off  
stereo/two-channel-sound,-mono  
Sound Type  
Sound Mode  
Stereo  
Normal  
Speech  
If the device receives two-channel-sound pro-  
grammes, e.g. a film with the original soundtrack  
on audio channel B (display: »Dual II«) and  
the dubbed version on sound channel A (dis-  
play: »Dual I«), you can select the audio channel  
you prefer.  
Sound Preset  
External connections  
Audio Output Setup  
Accessibility Settings  
If the device receives stereo or Nicam pro-  
grammes, it switches automatically to stereo  
sound (display: »Stereo«).  
End  
Back  
You can switch the sound to »Mono« if the stereo  
sound quality is poor.  
note:  
1
Select the line »Audio Type« with »  
v« or  
7
Additional operations are explained in the  
following sections.  
»Λ  
« and adjust the setting with » « or » «.  
<
>
stereo-width  
volume  
This broadens the sound output for stereo pro-  
grammes and improves the sound with mono  
reception.  
1
Select the line »Volume« with »  
v
« or »  
>
Λ
«
«
and change the setting with » « or » «.  
<
Balance  
1
1
Select the line »Audio Mode« with »  
or » «.  
v«  
Select the line »Balance« with »  
v
« or »  
>
Λ
Λ
and change the setting with » « or » «.  
<
2
Select the option »Spatial« with » « or » «.  
<
>
-19  
ENGLISH  
 
settinGs------------------------------------------------------------------------------------------------------------------------------------------  
soundeffects  
equalizer  
This menu offers three preset sound effects  
(Music, Natural and Speech) and one setting to  
be created by you (User).  
Equalizer offers a sound setting that you can cre-  
ate.  
Equaliser appears in the menu when »Sound  
mode« is selected as »Spatial« or »Normal«,  
and »Sound Medium« as »User«.  
1
Select the line »Sound Preset« with »  
v« or  
»
Λ«.  
1
2
Select »Equalizer« with »v« or »Λ« and  
2
Select the sound effect »Music«, »Natural«  
or »Speech« by pressing » « or » «.  
press »oK« to confirm.  
<
>
The »EQUALIZER« menu appears.  
note:  
note:  
7
»User« option is active when »Sound mode«  
setting is selected as »Normal or »Spatial«.  
7
If the »SRS TS HD« setting has been selected  
in the »Sound Mode« line, the »Equalizer«  
line will not indicate.  
srs-trusurround-hD  
SRS TruSurround HD is a patented audio tech-  
nology which is integrated into the television set  
and only requires the built-in speakers to gener-  
ate a Surround Sound effect.  
Select the frequency bandwidth »120Hz«  
with »v« or »Λ«.  
Set the preferred value with » « or » «.  
<
>
3
4
Set the next frequency bandwidth with »  
or » « and repeat the setting.  
v«  
1
2
3
4
Select the line »Sound Mode« with »  
or » «.  
v«  
Λ
Λ
Press » « to save the setting.  
<
Select the option »SRS TS HD« with » « or  
<
Audio-description-(Audio-subtitles)  
» «.  
>
Audio description is an additional audio channel  
for visually-impaired persons. Descriptions are  
provided of activities, surroundings, changes of  
scene, gestures and actors' facial expressions.  
Select the line »SRS Sound Preset« with »  
v«  
or »Λ«.  
Select the sound effect »Music«, »Natural«  
or »Speech« with » « or » «.  
<
>
This audio channel is transmitted simultaneously  
with the normal sound on digital channels. Avail-  
ability depends on the respective channel and  
broadcaster.  
1
Select the line »Audio Description« with »  
v
«
or »Λ  
« and select the option »On« with » «  
<
or » «.  
>
2
Select the line »Volume« with »  
v
« or »  
>
Λ
«
and change the volume with » « or » «.  
<
exiting-the-setting  
1
Press »menu« to end the setting.  
* Under licence from SRS Labs, Inc. TruSurround HD,  
SRS and the  
symbol are trademarks of  
SRS Labs, Inc.  
-20  
ENGLISH  
 
television---operAtion--------------------------------------------------------------------------------  
Displaying-information  
Basic-functions  
1- Display information with »?«.  
– The display disappears automatically after  
a short while.  
switching-on-and-off  
1
Press »8«, »1…0« or »p+« or »p-« to switch  
on the television from standby mode.  
Freeze-frame  
2
Press »8« to switch the television to standby.  
If you wish to view a particular scene for longer,  
you can “freeze” the frame of the current pro-  
gramme.  
selecting-channels  
1
Press »1…0« to select presets directly.  
1
2
Activate the freeze-frame function with »$«.  
End the freeze-frame function with »$«.  
2
Select channels step by step with »p+« or  
»p-«.  
3- Open the channel list with »oK«, select the  
preferred television channel with » «, » «,  
» « or » « and press »oK« to confirm.  
picture-settings  
Various picture settings are available.  
v
Λ
<
>
1
2
Open the Tools menu with »tools«.  
Exit the channel list with »menu«.  
Select the menu item »Picture Mode« with  
selecting-channels-from-lists  
You can select channels from various lists (e.g.  
all channels, FAV 1 to FAV 4).  
»v« or »Λ«.  
3- Select »User«, »Eco TV«, »Vivid«, »Natural«,  
»Movie«, »Sports« or »Game« by pressing  
» « or » «.  
1
Press »FAv« to open an overview of pro-  
grame tables.  
– The overview is displayed.  
<
>
note:  
7
Picture setting »Game« can only be selected  
in »HDMI«, »Component« and »PC« modes.  
2
3
4
Select a channel list with »  
Λ« or »v« and  
open it with »oK«  
.
Audio-settings  
Various audio settings are available.  
Select a television channel with »  
v«, »Λ«,  
» « or » « and press »oK« to confirm.  
<
>
Press »menu« to exit the channel list.  
1
2
Open the Tools menu with »tools«.  
Select the menu item »Sound Preset« with  
selecting-a-preset-Av-channel  
»v« or »Λ«.  
1
Open the »Select Source« menu with »  
Select an AV preset with » «, »  
» « and press »oK« to confirm.  
«.  
3
Select the audio setting »User«, »Music«,  
2
v
Λ«, » « or  
<
»Natural« or »Speech« by pressing » « or  
<
>
» «.  
>
3
Use »1…0« to switch back to the television  
channel.  
note:  
7
»User« option is active when »Sound mode«  
setting is selected as »Normal or »Spatial«.  
Adjusting-the-volume  
o
1
Adjust the volume with »  
«.  
- -–  
+
switching-sound-on/off  
1
Press » « to mute the sound or switch it  
p
on again.  
-21  
ENGLISH  
 
television---operAtion--------------------------------------------------------------------------------  
Audio-language  
electronic-tv-guide  
Various languages are available on digital tele-  
vision channels. This depends on the programme  
being broadcast.  
The electronic TV guide provides an overview of  
all programmes that will be broadcast in the next  
week (for digital channels only).  
1
2
Open the selection menu with »  
«.  
1
Press »GuiDe« to display channel informa-  
tion.  
Select the language by pressing »  
and press »oK« to confirm.  
v« or »Λ«  
notes:  
7
Not all channels supply provide a detailed  
subtitles  
TV guide.  
Various subtitles are available on digital televi-  
sion channels. This depends on the programme  
being broadcast.  
7
Many broadcasters transmit the current  
schedule, but do not offer detailed descrip-  
tions.  
1
2
Open the selection menu with » «.  
7
There are broadcasters which do not pro-  
vide any information at all.  
Select the subtitles with »v« or »Λ« and  
press »oK« to confirm.  
2
3
Press »v« or »Λ« to select a television  
channel.  
Zoom-function  
1
– Today's programmes on the television  
channel selected are displayed.  
Open the Tools menu with »tools«.  
2
Select the menu item »Zoom« with »v« or  
Switch to the information about the current  
»Λ«.  
programme with » «.  
>
3- Press- »oK« repeatedly to enlarge the  
notes:  
display in three steps.  
7
You can open and switch off the extensive  
programme information with »?«.  
eco-mode  
This function allows you to reduce the power  
consumption.  
7
You can can added the selected broadcast  
to the memory timer by pressing »oK«  
.
4
5
6
Press »  
v
« to select information on the next  
1
2
Open the Tools menu with »tools«.  
Select the menu item »Eco TV« with » « or »Λ«.  
programme and, »  
Λ
« to return to the infor-  
v
mation for the current programme.  
3- Switch on the Eco mode with » « or » «.  
<
>
Select programmes on over the coming days  
with » « (green), and switch back to the cur-  
4
Switch the Eco mode off again with » « or » «.  
  
<
>
rent day with » «-(red).  
Zapping-function  
This function remembers the channel you are  
currently watching while you switch over to other  
ones (zapping).  
Switch back to the channel selection with  
» «.  
<
note:  
7
Filter for certain programmes with »  
«
  
(blue), select the channel type with » «,  
1
Press »1…0« or »p+«, »p–« to select the  
<
channel to be stored in the zapping memory  
» «, »v« or »Λ« and press »oK« to con-  
>
and press » « to confirm.  
<
firm. Programmes which match the selected  
channel type are displayed.  
2
3
Press »1…0« or »  
Λ«, »v« to switch to  
another television channel.  
7- Quit the electronic TV guide with »menu«.  
Press » « to switch between the saved tel-  
<
evision channel and the last television chan-  
nel viewed.  
4- End the function with »menu«.  
-22  
ENGLISH  
 
television---operAtion--------------------------------------------------------------------------------  
»panorama«-format-  
Changing-the-picture-format  
This setting is suitable for films in an especially  
wide format.  
The television automatically switches to the 16:9  
format if this format is detected via the SCART  
socket.  
During programmes in 4:3 format, the picture is  
stretched horizontally if the »Panorama« function  
is selected. The picture geometry is stretched  
horizontally.  
1
Select the picture format with » «.  
– The picture format (for example »16:9«) is  
displayed.  
– You can choose between the following  
picture formats:  
»overscan«-format  
In this mode, HD pictures are not cropped by the  
HDMI sockets or component sockets, and are  
displayed in their original size. This only applies  
in HDMI mode and for resolutions of 720p or  
above.  
»Auto«-format  
The picture format is automatically switched to  
»16:9« for 16:9 programmes.  
The picture format is automatically switched to  
»4:3« for 4:3 programmes.  
»16:9«-and-»14:9«-formats  
For programmes in 4:3 format, the picture is  
stretched horizontally if the »16:9« format or  
»14:9« format is selected.  
The picture geometry is stretched horizontally.  
With actual 16:9 input sources (from a set-  
top box on the SCART socket) the picture fills  
the screen completely and with the correct  
geometry.  
»4:3«-format  
The picture is shown in 4:3 format.  
»letterBox«-format-  
The letterbox format is especially suitable for  
programmes in 16:9 format.  
The black borders which are usually at the top  
and bottom of the screen are eliminated, 4:3 pic-  
tures fill the screen.  
The transmitted pictures are enlarged, but are  
slightly cropped at the top and bottom. The pic-  
ture geometry remains unchanged.  
»subtitle«-format  
If you cannot see the subtitles at the bottom of  
the screen, select »Subtitle«.  
-23  
ENGLISH  
 
usB-operAtion----------------------------------------------------------------------------------------------------------------  
image-data  
File-formats  
Your television can display pictures in the formats  
JPEG, PNG and BMP.  
Your television can work with the following file  
formats using the USB sockets:  
JPEG stands for Joint Picture Experts Group.  
It denotes a process for compressing picture files.  
PNG and BMP are process used to save image  
data with no, or very little, losses.  
Picture files can be stored with other types of files  
on one medium.  
These files can be organised into folders and  
subfolders.  
video-data  
Special codecs for video compression and  
decompression provide more memory space  
without compromising the picture quality exces-  
sively.  
Your television plays video files in the formats  
DIVS, XVID, H.264/MPEG-4 AVC (L4.1, 4 ref-  
erence pictures), MPEG-4, MPEG-2, MPEG-1,  
MJPEG and MOV.  
The following file name extensions are also sup-  
ported: AVI, MKV, MP4, TS, MOV, MPG, DAT,  
VOB. These files can also contain audio files  
compressed using MP3, AAC or Dolby Digital©.  
Audio-data  
Your television can play audio data in the for-  
mats MP3, AAC, WMA.  
MP3 is the abbreviation for MPEG-1 Level 3 and  
is based on the MPEG-1 standard, which was  
developed by the MPEG (Motion Picture Expert  
Group).  
AAC stands for Advanced Audio Coding and  
was also developed by MPEG. AAC provides  
better sound quality at an identical data rate.  
WMA (Windows Media Audio) is a compres-  
sion standard for audio data developed by  
Microsoft.  
These formats allow audio files to be recorded  
and played which sound as good as a CD, while  
taking up only a fraction of the memory space.  
File name extensions which are supported: MP3,  
MP2, WMA, M4A, AAC.  
MP3 files can be organised into folders and  
subfolders, as on the computer.  
-24  
ENGLISH  
 
usB-operAtion----------------------------------------------------------------------------------------------------------------  
Connecting-external--  
data-media-  
Before connecting the data medium, switch the  
television to standby using »8«. Connect the  
device and then switch the television on again.  
Before removing the external data medium,  
the television set must be switched to standby,  
so that no data loss occurs.  
notes:  
7
If you use a network cable for external hard  
disks which are connected to the »usB«  
socket on the television, this network cable  
must also be disconnected from the power  
supply when the television is switched off.  
7
External data media may not be disconnect-  
1
2
Connect the »usB« socket of the television  
and the corresponding socket on the data  
device (external hard drive, digital camera,  
card reader or MP3 player) using a USB ca-  
ble;  
ed from the television set while files on the  
data medium are being accessed.  
7
A bi-directional data transfer as defined for  
ITE (Information Technology Equipment)  
devices in EN 55022/EN 55024 is not  
possible.  
or  
7
plug the memory stick into the USB interface  
»usB« of the television.  
USB transfer is not in itself an operating  
mode. It is only an additional function.  
Confirm the display »  
(green).  
« with  
»
«
  
– The file browser appears.  
-25  
ENGLISH  
 
usB-operAtion----------------------------------------------------------------------------------------------------------------  
the-file-browser-  
The file browser displays video, audio and  
picture files stored on external data media.  
settings-in-the-usB--  
setup-menu  
selecting-the-menu  
If an external data medium contains files in  
different formats, you can, when necessary, filter  
out the formats not required.  
1
Open the menu with »menu«.  
2
Select the »SOURCE SETUP« menu item with  
»v  
« or »  
Λ« and press »oK« to confirm.  
main-menu-of-the-file-browser  
–
The »USB SETUP« menu appears.  
note:  
3
1
2
7
Additional functions are explained in the  
following sections.  
VIDEO FILES  
switching-on-automatic-preview  
ROOT  
Photo  
Music  
Film  
If this function is switched on, a preview of the  
selected file then appears in the file browser.  
1
2
3
Select the line »Auto Preview« with »  
v«  
or »Λ«.  
USB DRIVE  
Used (MB)  
Total (MB)  
%3  
475  
45  
Switch on the function with » « or » «  
<
>
(»On«).  
Use Control  
Buttons  
x1  
Speed  
All  
Repeat  
Now  
Total  
Press »menu« to end the setting.  
selecting-the-display-mode  
5
2
4
1
Select »View Mode« with »v« or »Λ«.  
1
2
Selected data format.  
Total number of folders on the data medium.  
2- Select the preferred option with » « or » «.  
<
>
3
Press »menu« to end the setting.  
3- Preview of the selected file.  
setting-the-display-duration-for-  
pictures-in-a-slideshow  
1
4- Information on the external data medium.  
5
Menu navigation.  
Select »Slide Show Interval« with »v« or »Λ«.  
2
Selectthedisplayduration(3, 5, 10 seconds)  
with » « or » «.  
<
>
3
Press »menu« to end the setting.  
-26  
ENGLISH  
 
usB-operAtion----------------------------------------------------------------------------------------------------------------  
Divx®-voD  
Basic-playback-functions-  
You must have your device registered in order to  
play the protected video that you will buy from  
DivX®.  
1
Select the data medium by pressing »  
«,  
use » «, » «, » « or » « to select the option  
v
Λ
<
>
»USB« and press »oK« to confirm.  
– The file browser appears.  
1
Select »DivX® VOD« with »  
confirm with »oK«  
– Registration Code appears.  
v« or »Λ« and  
.
2
3
Select the file format (video files, audio files,  
picture files) with » « or » «.  
v
Λ
2
3
Visit “http://vod.divx.com” and register the  
device with the registration code.  
Switch to the folder/file list with »oK«.  
note:  
Press »menu« to end the setting.  
7
USB data medium with several partitions is  
connected to the USB sockets, the letter for  
the respective drive (e.g. C) appears behind  
the folder symbol. Select the letter of the  
DivX Certified® to play DivX® and DivX  
Plus™ HD (H.264/MKV) video up to  
1080p HD including premium content.  
drive with »  
confirm.  
v« or »Λ« and press »oK« to  
ABOUT DIVX VIDEO: DivX® is a digital video format created  
by DivX, Inc. This is an official DivX Certified® device that plays  
DivX video. Visit divx.com for more information and software  
tools to convert your files into DivX video.  
4
5
Select the folder or file with »v« or »Λ« and  
press »oK« to open it.  
– A list of subdirectories appears.  
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® de-  
vice must be registered in order to play purchased DivX Video-  
on-Demand (VOD) movies. To obtain your registration code,  
locate the DivX VOD section in your device USB setup menu.  
Go to vod.divx.com for more information on how to complete  
your registration.  
note:  
7
Switch back to the main folder with » «.  
<
Select the track or picture with »  
and press »8« to start playing.  
You can view information on the film data by  
pressing »?«.  
v« or »Λ«  
–
– When playing MP3 or WMA data, infor-  
mation on the album, track and singer is  
displayed at the left of the menu.  
– When playing picture files, you can use  
»?« to display information about the reso-  
lution and size.  
– When playing picture data, press »  
?«  
®
twice to enter the DivX Settings menu.  
note:  
7
When playing picture data, the file browser  
7
switches off. Press » « to display the file  
browser again.  
6
Press »!« to pause playback.  
7- Press »8« to resume normal playback.  
7
8
Press » « to end playback.  
The file browser appears.  
-27  
ENGLISH  
 
usB-operAtion----------------------------------------------------------------------------------------------------------------  
notes:  
Additional-playback--  
functions  
Depending on the file format, the following  
additional functions are available:  
7
Use »Λ« to select »Up Folder«, when you  
would like to return to the last folder. Use  
»Root« (and then press »oK«) to return to  
the main folder.  
selecting-chapters-on-Divx®-files  
(only video files)  
7
It is possible that files which are actually  
supported do not function correctly in USB  
mode. This is because certain files are not  
recorded with standardised compression  
processes, although they feature the “right”  
file ending.  
1
During playback, select the next chapter  
with » «.  
>
2
During playback, select the previous  
chapter with » «.  
<
7
7
7
If a video file features several audio tracks  
(audio streams), you can switch these over  
during playback in full screen mode with  
note:  
7
You can also select chapters by entering the  
chapter number with »1...0«.  
»
«.  
When playing music files, you can use other  
options in the USB mode at the same time.  
This way, you can, for example, enhance a  
slideshow with music.  
selecting-titles-on-Divx®-files  
(only video files)  
1
During playback, select the next title with  
«.  
»Λ  
For films, only subtitles in the SRT format  
are supported. The names of the subtitle  
and film files must be identical. Otherwise,  
no subtitles will be shown.  
2
During playback, select the previous title  
with » «.  
v
playing-selected-titles  
Only the marked tracks are played.  
1
Select the titles with »  
»oK« to mark it.  
v« or »  
Λ
« and press  
2
Select the next title with »  
v
« or » « and  
Λ
press »oK« to mark it.  
3
4
Start playback with »8«.  
7
Press » « to end playback.  
note:  
7
To remove the marking, select the title with  
« or » « and press »oK« to remove the  
marking.  
»v  
Λ
-28  
ENGLISH  
 
usB-operAtion----------------------------------------------------------------------------------------------------------------  
selecting-a-track-or-picture-in-steps-  
(sKip)  
1
During playback, select the next track/  
picture with »6«.  
2
During playback, select the previous track/  
picture with »5«.  
– Playback begins with the track or picture  
you selected.  
selecting-a-certain-passage-for-  
playback-  
(video files only)  
1
2
During playback, press »oK«  
Enter the passage (time) with »1-...-0« and  
press » « (green) or »oK« to confirm.  
.
  
Fast-forward  
(for video and audio files only)  
You can select different speeds (2-fold, 4-fold,  
8-fold,16-fold and 32-fold forwards and back-  
wards).  
1
Select the playback speed during playback  
with »3« or »4«.  
2- Press »8« to resume normal playback.  
rotating-pictures-  
(picture files only)  
You can rotate pictures by 90°.  
1
During playback, press » « or « to rotate  
the pictures by 90°.  
<
>
repeat-functions  
Options:  
– »One Repeat«: the current track will be  
repeated.  
– »All Repeat«: all tracks will be repeated.  
1
2
Open the Tools menu with »tools«.  
Select the menu item »Repeat« with »  
v« or  
»Λ«.  
3- Select »All«, »Random«, »One« or »None«  
by pressing » « or » «.  
<
>
-29  
ENGLISH  
 
teletext-operAtion-----------------------------------------------------------------------------------------------  
enlarging-the-character-height  
If you have difficulty reading the text on the  
screen, you can increase the character height.  
top-text-or-FloF-text-mode  
1
Press »txt« to switch on teletext.  
2
Select teletext pages directly with »1...0«  
1
To enlarge the character height of a teletext  
page, keep pressing »5«.  
or step by step with »v« and »Λ«.  
Return to teletext page 100 with »?«.  
note:  
page-hold  
7
At the bottom of the screen there is an info  
A multiple page may contain several sub-pages,  
which are automatically scrolled by the broad-  
casting station.  
bar with red, green and – depending on the  
channel – yellow and blue panels. Similarly,  
the remote control also features buttons with  
different colours with which these pages can  
be selected.  
1
Stop the automatic scrolling of the sub-pages  
with »3«.  
2- Quit the function with »3«.  
3
4
5
Go back a page with » «-(red).  
Go to the next page with » « (green).  
  
opening-a-sub-page-directly  
Select a particular chapter with  
»
«
  
If the selected teletext page contains additional  
pages, the number of the current sub-page and  
the total number of pages are displayed.  
(yellow)  
.
6- Select a particular subject with »  
« (blue).  
  
1- Press » « to open the sub-page function.  
2- Use » « or » « to select the sub-page.  
7
Quit teletext with »txt«.  
<
>
normal-text-mode  
1
3- Quit the function with » «.  
Press »txt« to switch on teletext.  
revealing-answers  
Certain teletext pages contain hidden answers  
or information.  
2
Press »1…0« to select teletext pages directly.  
Return to teletext page 100 with »?«.  
3
4
5
Go back a page with »v«.  
1
Display information with »4«.  
Go to the next page with »Λ«.  
2- Press »4« to conceal the information.  
Quit teletext with »txt«.  
split-screen  
Additional-functions  
This functions allows you to display the televi-  
sion channel on the left side, the teletext on the  
right side.  
skipping-the-waiting-time  
While a page search is progressing, you can  
switch to the TV programme.  
1
Switch the function on with »7«.  
– The television channel and teletext are dis-  
played next to each other.  
1
Enter the teletext page number with »1…0«  
and then press »6«.  
2
Switch the function off with »7«.  
– As soon as the page is found, the page  
number is displayed.  
2
Press »6« to switch to the teletext page.  
-30  
ENGLISH  
 
ConvenienCe-FunCtions-------------------------------------------------------------------------  
Changing-the-audio-language  
(only for digital television channels)  
opening-the-settinGs-menu  
1
Open the menu with »menu«.  
You can define a primary and a secondary  
audio language.  
2
Select the »SETTINGS« menu with »v« or  
»
Λ« and press »oK« to confirm.  
– The »SETTINGS« menu appears.  
1
Select the line »Audio« with »v« or »Λ« and  
press »oK« to confirm.  
–
The »Select Audio Language« menu  
20.09.2010  
15:46  
appears.  
SETTINGS  
2
Select the audio language with » «, » «,  
<
>
»v« or »  
Λ« and then use » «-(red) to set  
Language settings  
it as the primary audio language, or use  
»
« (green) to set it as the secondary audio  
  
Menu  
English  
English  
language.  
Audio  
Subtitle  
– The primary and secondary language is  
display at the top right in the menu.  
English  
Off  
Subtitle Mode  
Date and time settings  
3
Press »menu« to end the setting.  
Changing-the-subtitle-language-  
and-subtitle-mode  
(only for digital television channels)  
Date & Time  
Time Adjustment  
Time Zone  
Auto  
GMT +1  
You can switch the subtitles on and off, select the  
subtitle language and allocate a second subtitle  
language.  
Exit  
Back  
1
Select the line »Subtitle« with »v« or »Λ«  
note:  
and press »oK« to confirm.  
– The »Select Subtitle Language« menu ap-  
pears.  
7
Additional operations are explained in the  
following sections.  
2
Select the subtitle language with »  
v«,  
language-settings  
»Λ«, » « or » «, then use » «-(red) to set  
<
>
it as the primary subtitle language, or use  
  
Changing-the-menu-language  
»
« (green) to set it as the secondary subti-  
1
Select the line »Menu« with »v« or »Λ« and  
tle language.  
press »oK« to confirm.  
– The primary and secondary language is  
displayed at the top right in the menu.  
–
The »Select Menu Language« menu  
appears.  
3
4
To go back one menu level, press » «.  
<
2- Select the menu language with » «, » «,  
<
>
Select the line »Subtitle Mode« with »v« or  
»v« or »Λ« and press »oK« to confirm.  
»
Λ« and then set the preferred option »Off«,  
3
Press »menu« to finish the setting.  
»Hard of Hearing« or »Basic« with » « or  
<
» «.  
>
5
Press »menu« to end the setting.  
-31  
ENGLISH  
 
ConvenienCe-FunCtions-------------------------------------------------------------------------  
setting-the-date-and-time  
Automatic-setting  
Your television set detects the difference in time  
to Greenwich Mean Time (GMT) automatically,  
as long as the channel selected transmits a time  
signal.  
timer-settings  
entering-the-switch-off-time--  
(sleep-timer)  
In the »Sleep Timer« menu you can enter a time  
for the television to switch off. After this time  
has elapsed, the television switches to standby  
mode.  
1
2
Select the line »Time Adjustment« with »v«,  
1
Select the line »Sleep Timer« with »  
»Λ«.  
v« or  
then select the option »Manual« with » «  
<
or » «.  
>
– The lines »Time Zone« and »Daylight Sav-  
ing« are active.  
2
Enter the switch-off time with » « or » «.  
<
>
note:  
Select the line »Time Zone« with »v« and  
7
To switch off the function, use » « or » « to  
set the switch-off time to »Off«.  
<
>
press »oK« to confirm.  
– The »Select Time Zone« menu appears.  
3
Press »menu« to end the set-up.  
3- Select the appropriate time zone with » «,  
<
switch-on-timer  
» «, »  
v« or »Λ« and press »oK« to con-  
>
firm.  
In the »Auto On« menu you can enter a switch-on  
time for the television. After the preset time has  
elapsed, the television switches on from standby  
– at the preselected volume and the preselected  
television channel.  
4
5
Select the line »Daylight Saving« with »  
v«  
and use » « or » « to set the option »Auto«,  
<
>
»Off« or »On«.  
Press »menu« to finish the setting.  
1
Select the line »Auto On« with  
and press »oK« to confirm  
»v  
« or »  
Λ«  
.
manual-setting  
You can also set the difference in time manually  
– for example, when the correct time is not de-  
tected automatically or does not correspond to  
local time for other reasons  
2
Select the line »Mode« with  
»
v
« or » and  
Λ«  
use » « or » « to select when the television  
<
>
should switch on.  
3
4
Select the line »Input Source« with  
»v« or »Λ«  
and use » « or » « to select the input source.  
1
Select the line »Date & Time« with »  
v« or  
<
>
»
Λ
« and press »oK« to confirm.  
Select the line »Service Type« with  
»v« or »Λ«  
and use » « or » « to select the preferred op-  
2
Select the line »Auto« with »v« or »Λ  
« and  
<
>
tion (ATV, DTV, Radio or DATA).  
Select the line »Channel« with  
press »oK« to confirm.  
– Date and Time will be updated  
automatically;  
5
»v« or »Λ«  
and use » « or » « to select the preferred  
<
>
channel.  
or  
note:  
3
Select the input box with »v« or »Λ«, enter  
the data for Date and Time with »1...0«  
and press »oK« to confirm.  
7
The line »Channel« is only active when the in-  
put signal currently in use has been set. If no  
entry has been made, then the first channel of  
the selected input source will be used.  
-32  
ENGLISH  
 
ConvenienCe-FunCtions-------------------------------------------------------------------------  
6
Select the line »Volume« with  
»
v
« or »  
Λ
«
and  
parental-control-settings  
Authorising-programmes  
There are films which may be wholly or partially  
unsuitable for children.  
use » « or » « to set the volume.  
<
>
7
Select the line »Set Hour« with  
»
v« or »Λ«  
and enter the time with »1…0«.  
8- Save the data with » « (green).  
  
These programmes contain information which  
marks the content or scenes with access levels of  
4 to 18. You can select one of the access levels,  
thereby authorising playback.  
note:  
7
You can abort the entry by pressing » «-(red)  
.
9
Press »menu« to end the setting.  
1
Select the line »Parental Guidance« with  
« or » « and press »oK« to confirm.  
switch-off-timer  
»v  
Λ
In the »Auto Off« menu, you can enter a time  
for the television to switch off. After this time  
has elapsed, the television switches to standby  
mode.  
2
3
4
Enter the PIN code »1234« with »1-...-0«.  
Select the access level with » « or » «.  
<
>
Press »menu« to end the setting.  
1
2
3
Select the line »Auto Off« with  
»
v
« or »  
Λ«  
locking-menus  
and press »oK« to confirm  
.
This function allows you to lock the »Automatic  
Channel Search«, »Digital Manual Tuning«, »An-  
alogue Manual Tuning« and »Program Table«  
menus so that they can be only accessed by  
entering a PIN code.  
Select the line »Mode« with  
»
v
« or » and  
Λ«  
use » « or » « to set the preferred mode.  
<
>
Select the line »Set Hour« with  
»v« or »Λ«  
and enter the time with »1…0«.  
4- Save the data with » « (green).  
1
2
3
Select »Menu Lock« with »v« or »Λ«.  
  
note:  
Enter the PIN code »1234« with »1-...-0«.  
7
You can abort the entry by pressing » «-  
(red).  
Activate the lock with » « or » « (»On«).  
<
>
note:  
5
Press »menu« to end the setting.  
7
To switch off the menu lock, use » « or » «  
to select the setting (»Off«).  
<
>
Automatic-switch-off-(Auto-sleep)  
If this function is activated, the television switches  
to standby after 5 minutes if no video signal is  
broadcast.  
4
Press »menu« to end the setting.  
locking-keys-(parental-lock)  
When the key lock is activated, the buttons on  
the television set do not function.  
1
Select the line »Auto Sleep« with »  
v« or  
»Λ«.  
1
Select the line »Keypad Lock« with »  
«.  
v« or  
2
Activate the function with » « or » «  
<
>
»Λ  
(»On«).  
2
Enter the PIN code »1234« with »1-...-0«.  
note:  
7
To switch off the function, use » « or » « to  
select the setting »Off«.  
3- Activate (On) or deactivate (Off) the key lock  
<
>
with » « or » «.  
<
>
3
Press »menu« to end the setting.  
4
Press »menu« to end the setting.  
-33  
ENGLISH  
 
ConvenienCe-FunCtions-------------------------------------------------------------------------  
Changing-the-pin-code  
updating-software  
You can also enter a personal PIN code instead  
of the default code »1234«. Please take note of  
your own PIN code.  
(for digital channels only)  
1
In the »SETTINGS« menu, select the line  
»Check For Updates updates« with » « or  
« and press »oK« to confirm.  
v
1
2
3
4
5
Select »Set PIN« with »v« or »Λ« and press  
»Λ  
»oK« to confirm.  
– A search for new software will be made  
and – if available – it will be installed.  
Enter the current PIN code 1 2 3 4 with  
»1...0«.  
note:  
7
If a search for software updates should be  
Enter your new four digit PIN code with  
»1...0«.  
made automatically, select the line »Auto-  
matic OAD« with »v« or »Λ« and use » «  
<
Enter your new four digit PIN code with  
»1...0« again.  
or » « to select the option »On«.  
>
– The software will be updated automati-  
cally as far as possible.  
Press »menu« to end the setting.  
2
Press »menu« to end the setting.  
locking-television-channels-  
You can lock individual television channels, for  
example channels unsuitable for children, using  
a personal PIN code.  
restoring-the-television-to-the-  
default-settings  
This function allows you to delete the channel  
lists and all custom settings.  
1
2
Open the menu with »menu«.  
Select the »SOURCE SETUP« menu with »  
or »Λ« and press »oK« to confirm.  
v«  
1
2
3
In the »SETTINGS« menu, select the line  
»Restore Factory Defaults« with »v« or »Λ«  
3
Select the line »Program Table« with »  
v« or  
and press »oK« to confirm.  
»Λ« and press »oK« to confirm.  
Press » « (green) to confirm the warning  
  
– The »PROGRAM TABLE« menu is dis-  
played.  
message.  
– The »Source Setup« menu appears.  
4
5
6
7
In the »PROGRAM TABLE« menu, switch  
Continue the settings with the chapter “Initial  
set-up and tuning television channels” on  
page 14.  
over to the list view with » « (yellow).  
  
Select the channel to be locked with »  
v«  
or »Λ«.  
Select the column »Lock« with » « or » «  
<
>
and press »oK« to lock the channel.  
Enter the PIN code »1234« with »1-...-0«.  
– The channel is marked using »✔«.  
note:  
7
To remove the lock, select the channel again  
with »v« or »Λ«, press »oK« to confirm  
and then enter the PIN code 1 2 3 4 using  
»1-...-0«.  
8
Press »menu« to end the setting.  
-34  
ENGLISH  
 
operAtion-usinG-externAl-DeviCes------------------------------  
searching-for-and-activating--  
external-devices  
You can connect up to 11 devices with DIGI LINK  
functions to your television.  
DiGi-linK  
Your television is equipped with  
the DIGI LINK function.  
This function uses the CEC  
(Consumer Electronics Control)  
protocol.  
1
Open the CEC device list with »CeC«.  
– The »HDMI CEC Device List« appears.  
CEC allows external devices which are connect-  
ed to the »hDmi« sockets by an HDMI cable  
(e.g. DVD player) to be operated with a remote  
control.  
Prerequisite is that the devices connected support  
CEC. Read the operating manual for the external  
device to find out how to activate the correspond-  
ing function.  
2
Start the device search with » «-(red).  
The devices found are displayed in the  
menu.  
–
3- Select the device for operation with »  
v«,  
»
Λ
«, » « or » « and press »oK« to mark it.  
<
>
– If the selected device is connected to a  
different input to the current one, a switch  
to the respective input will occur auto-  
matically.  
the-DiGi-linK-functions-on-your-  
television  
4
Press »menu« to end the setting.  
switching-on-the-television--  
automatically-from-standby  
If the »Autom. switch-on TV« function is activated  
(»On«), then once the external device (e.g.  
DVD player) is switched on, the television also  
switches on and the appropriate HDMI preset is  
selected.  
Automatic-selection-of-the-hDmi-  
preset-on-the-television  
If your television is switched on and you then  
switch on the external device (e.g. DVD player),  
the appropriate HDMI preset on the television  
will be selected.  
selecting-the-menu-language  
The television menu language is automatically  
selected on the external device (e.g. DVD player).  
The external device must support this function.  
switching-off-the-external-device-  
automatically  
If you switch your television to standby, the ex-  
ternal device (if it is switched on) will also be  
switched to standby.  
DIGI LINK is always active on your television set.  
-35  
ENGLISH  
 
operAtion-usinG-externAl-DeviCes------------------------------  
switching-the-device-to-standby  
This option switches the external device to  
standby.  
Device-operation  
You can decide whether external devices should  
react to your television's remote control.  
1
Press »  
«, use »v«, »Λ«, » « or » « to  
1
Press »  
«, use »v«, »Λ«, » « or » « to  
<
>
<
>
select the preset »HDMI1« to »HDMI3« and  
press »oK« to confirm.  
select the preset »HDMI1« to »HDMI3« and  
press »oK« to confirm.  
2
3
Open the menu with »menu«.  
Select the menu item »SOURCE SETUP« with  
2
3
Open the menu with »menu«.  
Select the menu item »SOURCE SETUP« with  
»
v« or »Λ« and press »oK« to confirm.  
»
v« or »Λ« and press »oK« to confirm.  
– The »SOURCE SETUP« menu appears.  
– The »SOURCE SETUP« menu appears.  
4
Select »Device Standby« with »v« or »Λ«  
20.09.2010  
15:46  
and press »oK« to confirm.  
SOURCE SETUP  
– The external device switches itself off.  
Source  
HDMI1  
DIGILINK  
GRUNDIG DVD  
RC Passthrough  
Device Selection  
Remote Control  
Device Standby  
Exit  
Back  
4
Select the line »Remote Control« with »  
or » «.  
v«  
Λ
5- Select the type of operation (»RC Pass-  
through«, »Deck« or »Tuner« with » « or  
<
» «.  
>
notes:  
7
»RC Passthrough« can be used for all devices.  
»Deck« and »Tuner« can be selected in ac-  
cordance with the external device which  
has been connected.  
7
Try out which type of remote control opera-  
tion the external device reacts to the best.  
7
Read about the scope of functions of the  
DIGILINK-compatible device in the respec-  
tive operating manual.  
6
Press »menu« to end the setting.  
-36  
ENGLISH  
 
operAtion-usinG-externAl-DeviCes------------------------------  
high-definition--hD-ready  
Connection-options  
7
Which television socket(s) you connect your  
Connect the cor-  
external devices to depends on the sockets  
the external device is equipped with and the  
signals which are available.  
responding input  
sources (e.g. HDTV  
receiver or HD-  
DVD player) to the  
»hDmi« sockets  
(for digital HDTV  
sources).  
7
Please note: With many external devices,  
the resolution of the video signal must be  
adjusted to the input sockets of the television  
(see the operating manual of the external  
device). You can find out which values you  
need to set by referring to the guidelines in  
the sections about the various connection  
options.  
This ensures that you can view digital HDTV  
programmes, even if they are copy-protected  
(HDCP High Bandwidth Digital Content Protec-  
tion), without encountering problems.  
7
Do not connect any other equipment while  
the device is switched on. Also switch off the  
other equipment before connecting it.  
7
Do not plug in the power cord of the device  
until you have connected the external equip-  
ment and the antenna.  
-37  
ENGLISH  
 
operAtion-usinG-externAl-DeviCes------------------------------  
...-using-the-sCArt-socket--  
(CvBs/rGB-signal)  
Connecting-external-devices  
...-with-digital-audio/video-signals  
7
Suitable devices: Digital satellite receiver,  
7
Suitable devices: Digital satellite receivers,  
DVD player/recorder, set-top box, games con-  
sole, video recorder, decoder.  
Video signal: CVBS/RGB.  
Audio signal: stereo, analogue.  
»AV1« preset.  
Playstation, BluRay player, DVD player/  
recorder, set-top box, notebook, PCs.  
Video signal: Digital video; resolution: stand-  
7
7
7
ard 576p; HDTV 720p, 1080i, 1080p.  
Audio signal: digital audio (stereo, multi-chan-  
7
7
1
Connect the »Av1/s-vhs« socket on the  
television and the corresponding socket on  
the external device using a SCART cable  
(video and audio signal).  
nel compression, uncompressed).  
Presets »HDMI 1«, »HDMI 2« or »HDMI3«.  
7
1
Connect the »hDmi1«, »hDmi2« or  
»hDmi3« socket on the television and the  
corresponding HDMI socket on the external  
device using a standard HDMI cable (digital  
video and audio signal).  
Activating-a-decoder  
If a decoder is connected to the »Av1/s-vhs«  
socket, this must be activated to provide an  
unencrypted video/audio signal.  
...-with-analogue-video-signal-  
(progressive)  
1
2
Open the menu with »menu«.  
Select »SETTINGS« with »v« or »Λ« and  
press »oK« to confirm.  
– The »SETTINGS« menu appears.  
7
Suitable devices: DVD recorders/players,  
games consoles.  
Video signal: YUV; resolution: standard 576p;  
7
HDTV 720p, 1080i, 1080p.  
Audio signal: stereo, analogue.  
»Component« preset.  
3
4
Select the »Decoder« with »  
v« or »Λ«.  
7
Activate the function with » « or » «  
(»On«).  
Press »menu« to end the setting.  
<
>
7
1
2
Connect the »Component- Y/Av2- pb-  
pr« sockets on the television to the corre-  
sponding sockets of the external device with  
RCA cables (video signal).  
5
...-with-s-video-signal  
7
Suitable devices: DVD player/recorder, video  
recorder, camera recorder, notebook, PC.  
Video signal: Y/C.  
Audio signal: stereo, analogue.  
»S-VHS« preset.  
Connect the »Component-l-r« sockets  
on the television to the corresponding sock-  
ets of the external device with RCA cables  
(audio signal).  
7
7
7
1- Connect the » Av1/s-vhs« socket on the  
television and the corresponding socket on  
the external device using an EURO/AV ca-  
ble (video and audio signal).  
-38  
ENGLISH  
 
operAtion-usinG-externAl-DeviCes------------------------------  
...-with-an-analogue-tv-signal  
using-a-DvD-player,-  
DvD--recorder,-video-recorder--  
or-set-top-box  
7
Suitable devices: Digital satellite receiver,  
DVD player/recorder, set-top box, camera  
recorder.  
Video signal: CVBS.  
Audio signal: stereo, analogue.  
»AV2« preset.  
1
Switch on the external device and select the  
function you wish to use.  
7
7
2
Press  
»
«, use »v«, »Λ«, » « or » « to  
7
<
>
select the preset for the input signal (»AV1«,  
»AV2«, »S-VHS«, »HDMI1«, »HDMI2«,  
»HDMI3« or »Component«) and press  
»oK« to confirm.  
1
2
Connect the »Y/Av2« socket on the  
television to the corresponding socket of the  
external device with an RCA cable (video  
signal).  
Connect the »l--r« sockets on the television  
to the corresponding sockets of the external  
device with RCA cables (audio signal).  
headphones  
Connecting-the-headphones  
1
Plug the headphone jack (3.5 mm ø jack  
plug) into the headphone socket on the left  
side of the television.  
Changing-the-headphone-volume  
1
Open the menu with »menu«.  
2
Select the menu item »SOUND SETTINGS«  
with »v« or »Λ« and press »oK« to confirm.  
– The »SOUND SETTINGS« menu appears.  
3
4
Select the menu item »Audio Output Setup«  
with »  
v« or »Λ« and press »oK« to confirm.  
– The »Audio Output Setup« menu appears.  
Select the line »Headphone« with » « or  
v
»Λ«.  
5
6
Set the preferred volume with » « and » «.  
<
>
Press »menu« to end the setting.  
note:  
7
Prolonged listening with headphones at loud  
volumes can damage your hearing.  
-39  
ENGLISH  
 
operAtion-usinG-externAl-DeviCes------------------------------  
playing-the-audio-signal-via-the--  
hiFi-system  
1- Connect the »U« sockets on the television to  
the corresponding socket of the AV receiver  
with an cable (digital audio signal).  
hi-fi-system/Av-receiver  
Connecting-the-hi-fi-system/-  
Av-receiver  
1- Connect the »optic- out« socket on the  
television to the corresponding socket of the  
device with an optical digital cable (digital  
audio signal).  
note:  
7
If this function is not activated, the audio sig-  
nal is transmitted to the HiFi system/AV re-  
ceiver (connected to »U« 3.5 mm ø jack  
plug) into the headphone socket on the left  
side of the television.  
setting-the-audio-format  
You can select whether the audio signal output  
via the »optic-out« socket should be in the  
PCM or AC2 format.  
1
2
Open the menu with »menu«.  
1
2
Open the menu with »menu«.  
Select the menu item »SOUND SETTINGS«  
with »v« or »Λ« and press »oK« to confirm.  
Select the menu item »SOUND SETTINGS«  
– The »SOUND SETTINGS« menu appears.  
with »v« or »Λ« and press »oK« to confirm.  
– The »SOUND SETTINGS« menu appears.  
3
4
5
Select »Audio Output Setup« with » « or  
v
»
Λ« and press »oK« to confirm.  
3
Select »Audio Output Setup« with » « or  
v
– The menu appears.  
»
Λ« and press »oK« to confirm.  
– The menu appears.  
Select the line »Audio Out« with »v« or »Λ«  
and press » « or » « to activate the audio  
4
5
Select the »Optic Out« with »v« or »Λ«.  
<
>
output (»Line Out«).  
Select the line » Audio Out Status« with »  
or » « and select the option »Fixed« or »Ad-  
justable« with » « or » «.  
Select the preferred audio format (»PCM« or  
»Auto«) with » « or » «.  
v«  
<
>
Λ
note:  
<
>
7
If you wish to output the audio only via a  
multi-channel amplifier/AV receiver, set the  
option »TV Speaker« to »Off« in the menu.  
notes:  
7
If you select »Adjustable«, the volume can  
be changed in the menu option » Audio Out  
Volume«.  
6
Press »menu« to end the setting.  
7
If the audio should only be output via the  
HiFi system/AV receiver, select the option  
»Off« in the line »TV Speaker with » « or  
<
» «.  
>
6
Press »menu« to end the setting.  
“Dolby” and the double-D logo are trademarks of  
Dolby Laboratories.  
Manufactured under licence from Dolby Laboratories.  
-40  
ENGLISH  
 
operAtion-As-A-pC-monitor-----------------------------------------------------------  
Connecting-a-pC  
20.09.2010  
15:46  
1
Connect the »pC-in« socket on the television  
to the corresponding socket on the PC using  
a VGA cable (video signal).  
SOURCE SETUP  
2
Connect the »Audio« socket on the televi-  
sion to the corresponding socket on the PC  
using a suitable cable (audio signal).  
Source  
PC  
Auto Ajust  
Extended settings  
note:  
Auto Ajust Mode  
On  
50H - 50V  
0
7
Adjust your PC to the monitor (for example,  
picture resolution 1280 x 768, picture fre-  
quency 60 Hz).  
Position  
Size  
Phase  
30  
selecting-presets-for-the-pC  
1
Press »  
« and use »v«, »Λ«, » « or » «  
<
>
Exit  
Back  
to select the preset »PC« and press »oK« to  
confirm.  
Options:  
settings-for-pC-mode  
–
»Auto Ajust« for automatic PC configura-  
tion.  
1
Open the menu with »menu«.  
– »Auto Ajust Mode«, select the option  
»On« if the configuration should be imple-  
mented automatically in PC mode.  
– »Position« to configure the horizontal and  
vertical picture position.  
– »Size« to set the cycle frequency.  
– »Phase« to eliminate flicker, unfocused  
pictures or horizontal interference.  
2
Select the »SOURCE SETUP« menu item with  
»
v« or »Λ« and press »oK« to confirm.  
– The »SOURCE SETUP« menu appears.  
3- Select the function or setting with » « or  
«, and then use » «, » « or » «, » « to  
implement it.  
v
»
Λ
v
Λ
<
>
4
Press »menu« to end the setting.  
-41  
ENGLISH  
 
operAtion-with-A-Common-interFACe-------------------  
what-is-a-Common-interface?  
Access-control-for-Ci-module-and-  
smart-card  
7
Common Interface (CI) is an interface for  
DVB receivers.  
Encrypted channels can only be viewed  
1
Open the menu with »menu«.  
7
2
Select the line »SOURCE SETUP« with »  
or »Λ« and press »oK« to confirm.  
v«  
with a CA module suitable for the encryp-  
tion system and in conjunction with the  
corresponding smart card.  
The television set is equipped with a Com-  
mon Interface slot into which CI modules  
from various providers can be inserted.  
You can insert the provider’s smart card into  
the CA module in order to enable the en-  
crypted channels you wish to view.  
– The »SOURCE SETUP« menu appears.  
Select the line »CA-Module« with » « or  
« and press »oK« to confirm.  
7
3
v
»
Λ
notes:  
7
7
This menu provides operating instructions  
and – after you enter your PIN code – ac-  
cess to the PAY-TV provider's channels.  
inserting-the-CA-module  
note:  
7
7
The remaining settings are described in the  
operating manuals for your CI module and  
smart card.  
7
Switch the device off before you insert a CA  
module into the »Ci« slot.  
The CA modul is not supported in certain  
countries and regions; please consult your  
authorised dealer.  
1
2
Insert the corresponding smart card into the  
CI module.  
Insert the CI module with the smart card into  
the »Ci« slot on the television.  
4
Press »menu« to end the setting.  
note:  
7
In the »CA Module« sub-menu you can see  
which CA module has been inserted in the  
CI slot.  
7
If you are inserting a CA module into the  
CI slot of the television for the first time, you  
will need to wait a moment until the CA mod-  
ule is detected.  
-42  
ENGLISH  
 
speCiAl-settinGs-----------------------------------------------------------------------------------------------------------  
note:  
searching-for-television-chan-  
7
You can accelerate the search. To do this,  
you need information about the frequency  
and network ID. You are usually able to get  
this data from your cable operator or find it  
in forums on the Internet. For example, the  
frequency 402MHz and network ID 61441  
can be entered for Germany.  
nels-from-the-cable-provider-  
automatically  
1
Open the menu with »menu«.  
2
Select the line »SOURCE SETUP« with »  
or »Λ« and press »oK« to confirm.  
v
«
«
– The »SOURCE SETUP« menu appears.  
Select the line »Source« with  
or » « and press »oK« to confirm.  
Select the option »Cable« with » «, » «,  
7
Start the scan with » «-(red).  
– All channel and favourites lists will be  
deleted and compiled anew.  
3
4
»
v
Λ
<
>
»v  
« or »  
Select the line »Automatic Channel Search«  
with » « or » « and press »oK« to confirm.  
– The menu appears.  
Λ« and press »oK« to confirm.  
note:  
7
After starting the scan, a security query will  
appear. Press » « (green) to confirm the  
v
Λ
  
option »Yes«.  
– The »Results« menu appears, and the scan  
for TV channels begins. Depending on the  
number of television channels received,  
this can easily take a few minutes.  
20.09.2010  
15:46  
SOURCE SETUP  
AUTOMATIC CHANNEL SEARCH  
– The scan is complete as soon as the »PRO-  
GRAM TABLE« appears.  
Connection Type  
Cabel  
U.K.  
Country  
note:  
ATV & DTV  
Quick  
Scan Type  
7
You can abort the search by pressing  
»menu«.  
Cable Scan Type  
Frequency (MHz)  
Network ID  
Auto  
8
Press »menu« to end the setting.  
Auto  
Exit  
Back  
Start Search  
5
6
Select the line »Scan Typ« with »  
v
« or »  
Λ
«
and set the option »DTV« with » « or » «.  
<
>
Select the line »Cable Scan Type« with »  
or »  
with » « or » «.  
v«  
Λ« and set the option »Quick« or »Full«  
<
>
– The search function »Quick« sets the channels  
according to the information provided by your  
cable provide in the transmission signal.  
– If the option »Full« is selected, the entire fre-  
quency range will be scanned. The search  
can take a long time with this option. This op-  
tion is recommended if your cable provider  
does not support the search type »Quick«  
.
-43  
ENGLISH  
 
speCiAl-settinGs-----------------------------------------------------------------------------------------------------------  
searching-for-television-channels- searching-for-digital-terrestrial-  
from-the-cable-provider-manu-  
ally  
tv-channels-automatically  
1
Open the menu with »menu«.  
1
Open the menu with »menu«.  
2
Select the line »SOURCE SETUP« with »  
v
«
«
or »Λ« and press »oK« to confirm.  
2
Select the line »SOURCE SETUP« with »  
v
«
«
– The »SOURCE SETUP« menu appears.  
Select the line »Source« with  
or » « and press »oK« to confirm.  
Select the option »Air« with » «, » «, »  
or »Λ« and press »oK« to confirm.  
– The »SOURCE SETUP« menu appears.  
3
»
v
Λ
3
Select the line »Source« with »v« or »  
Λ
v« or  
and press »oK« to confirm.  
<
>
»
Λ« and press »oK« to confirm.  
Select the option »Cable« with » «, » «,  
<
>
»v« or »Λ« and press »oK« to confirm.  
Caution:  
4
5
Select » Digital Manual Tuning« with »  
v
« or  
7
The antenna power supply (line »Active  
Antenna Power«) may only be switched on  
if the antenna is an active indoor antenna  
with a signal amplifier and it is not already  
supplied with a voltage via a mains plug  
(or similar supply). Otherwise you may  
cause a short circuit and irreparably dam-  
age your antenna.  
»
Λ
« and press »oK« to confirm.  
– The menu appears.  
Enter the four-digit frequency with »1-...-0«  
and press »oK« to confirm.  
–
The search starts after confirming, the  
channels found are displayed in the »Re-  
sults« menu.  
4
5
Select the »Active Antenna Power« with »  
or » «. Switch on the antenna power supply  
for the antenna with » « or » « (»On«).  
v«  
6
Press »menu« to finish the setting.  
Λ
<
>
Select the line »Automatic Channel Search«  
with »v« or »Λ« and press »oK« to confirm.  
– The menu appears.  
20.09.2010  
15:46  
SOURCE SETUP  
AUTOMATIC CHANNEL SEARCH  
Connection Type  
Air  
U.K.  
Country  
ATV & DTV  
Scan Type  
Exit  
Back  
Start Search  
-44  
ENGLISH  
 
speCiAl-settinGs-----------------------------------------------------------------------------------------------------------  
6
Select the line »Scan Typ« with »  
v« or »Λ«  
searching-for-digital-terrestrial-  
tv-channels-manually  
and set the option »DTV« with » « or » «.  
<
>
7
Start the scan with » «-(red).  
1
Open the menu with »menu«.  
– All channel and favourites lists will be  
deleted and compiled anew.  
2
Select the line »SOURCE SETUP« with »  
v
«
«
or »Λ« and press »oK« to confirm.  
note:  
– The »SOURCE SETUP« menu appears.  
7
After starting the scan, a security query will  
3
Select the line »Source« with »v« or »  
Λ
appear. Press » « (green) to confirm the  
  
and press »oK« to confirm.  
option »Yes«.  
Select the option »Air« with » «, » «, »v« or  
<
>
– The »Reults« menu appears, and the scan  
for TV channels begins. Depending on the  
number of television channels received,  
this can easily take a few minutes.  
– The scan is complete as soon as the  
»PROGRAM TABLE« appears.  
»Λ  
« and press »oK« to confirm.  
Caution:  
7
The antenna power supply (line »Active  
Antenna Power«) may only be switched on  
if the antenna is an active indoor antenna  
with a signal amplifier and it is not already  
supplied with a voltage via a mains plug  
(or similar supply). Otherwise you may  
cause a short circuit and irreparably dam-  
age your antenna.  
note:  
7
You can abort the search by pressing  
»menu«.  
8
Press »menu« to end the setting.  
4
5
6
Select the »Active Antenna Power«« with »  
or » «. Switch on the antenna power supply  
for the antenna with » « or » « (»On«).  
v«  
Automatic-service-update-  
If this function is activated, possible changes of  
network operators are updated automatically.  
Λ
<
>
Select » Digital Manual Tuning« with »  
« and press »oK« to confirm.  
– The menu appears.  
v« or  
The unit must be located in stand-by mode.  
»Λ  
1
2
Open the menu with »menu«.  
Select the line »SOURCE SETUP  
or » « and press »oK« to confirm.  
Select the line »Automatic Service Update«  
with » « or » «.  
Enter the channel number directly with  
1-...-0« and press »oK« to confirm.  
«
with »v«  
»
Λ
–After the search is complete, the channels  
found are displayed in the »Results« menu.  
3
4
5
v
Λ
7
Press »menu« to finish the setting.  
Select the automatic update with » « or » «  
(»On«).  
<
>
Press »menu« to end setting.  
-45  
ENGLISH  
 
speCiAl-settinGs-----------------------------------------------------------------------------------------------------------  
5
Select the line »Scan Typ« with »  
v« or »Λ«  
tuning-analogue-television-  
-channels  
This setting is only necessary if you cannot re-  
ceive any digital channels and you have not car-  
ried out an analogue search during initial setup.  
The television channels can be set directly or  
using the scan.  
and set the option »ATV« with » « or » «.  
<
>
6
Start the scan with » «-(red).  
note:  
7
After starting the scan, a security query will  
appear. Press » « (green) to confirm the  
  
option »Yes«.  
– All channel and favourites lists for the ana-  
logue channels will be deleted and com-  
piled anew.  
setting-all-analogue-television-  
channels  
– The »Results« menu appears, and the scan  
for TV channels begins. Depending on the  
number of television channels received,  
this can easily take a few minutes.  
– The search is complete as soon as the »PRO-  
GRAM TABLE« appears.  
Analogue channels are displayed in the channel  
list after the digital channels.  
note:  
7
Plug the rooftop antenna cable (for analogue  
television channels) into the »Ant-in«  
socket on the television.  
note:  
1
2
Open the menu with »menu«.  
7
You can abort the search by pressing  
»menu«.  
Select the line »SOURCE SETUP« with »  
v
«
«
or »Λ« and press »oK« to confirm.  
7
Press »menu« to end the setting.  
– The »SOURCE SETUP« menu appears.  
3
4
Select the line »Source« with »v« or »  
Λ
and press »oK« to confirm.  
Select the option »Air« or »Cable« with » «,  
<
» «, »  
v« or »Λ« and press »oK« to con-  
>
firm.  
Select the line »Automatic Channel Search«  
with »  
v« or »  
Λ« and press »oK« to confirm.  
20.09.2010  
15:46  
SOURECE SETUP  
Source  
Air  
OK  
Automativ Channel Search  
Digital Manual Tuning  
Analogue Manual Tuning  
Program Table  
Signal Information  
Automatic Service Update  
On  
CA - Modul  
Not inserted  
Off  
Active Antenna Power  
Exit  
Back  
-46  
ENGLISH  
 
speCiAl-settinGs-----------------------------------------------------------------------------------------------------------  
tuning-the-television-channels-by-  
entering-the-channel-numbers  
Changing-stored-analogue-  
-channels  
If channels were stored with the automatic chan-  
nel search while tuning the television channels,  
you can delete them. You can also store chan-  
nels in a different preset, change or enter the  
name of a channel as well as skip channels.  
1
Open the menu with »menu«.  
2
Select the line »SOURCE SETUP« with »  
v«  
or »Λ« and press »oK« to confirm.  
– The »SOURCE SETUP« menu appears.  
3
Select the line » Analogue Manual Tuning«  
with »v« or »Λ« and press »oK« to confirm.  
selecting-a-channel-list  
– The menu appears.  
1
Open the menu with »menu«.  
2
Select the line »SOURCE SETUP« with »  
v«  
INSTALLATION  
ANALOGUE MANUAL TUNING  
or »Λ« and press »oK« to confirm.  
– The »SOURCE SETUP« menu appears.  
Program No  
TSystem  
Band  
1
BG  
C
3
Select the line »Program Table« with » « or  
v
»
Λ« and press »oK« to confirm.  
– The »PROGRAME TABLE« menu appears.  
note:  
Channel  
2
7
Additional operations are explained in the  
following sections.  
Fine Tuning  
0
48.25 MHz  
Deleting-channels  
1
In the »PROGRAME TABLE« menu, select the  
television channel to be deleted with «,  
«, » « or » « and press » «-(red) to con-  
Auto Previous  
Auto Next  
Store  
»v  
»
Λ
firm.  
<
>
4
5
Select the line »Program No« by pressing »  
or » « and use » « or » « to save the preset.  
Select »Band« by pressing »  
use »» « or » « to choose between »S«  
v«  
Λ
<
>
2
Press » « (yellow) to confirm the deletion  
  
v
« or »  
(special channel) or »C« (normal channel).  
Select the line »Channel« with » « or » « and  
Λ« and  
process.  
<
>
note:  
7
»
« (blue) allows all television channels  
  
6
v
<
Λ
>
enter the channel number with » « or » « step  
by step, or use »1…0« to enter it directly.  
to be deleted.  
3
Press » « (green) to confirm the deletion  
  
notes:  
process.  
7
The current system is displayed in the  
»System« line. If the colour or sound is  
not functioning properly, select the line  
»System« with »v« or »Λ«. Use » « or » «  
<
>
to select the preferred setting.  
7
If fine tuning is necessary, select the line  
»Fine Tuning« with » « or » « and use » «  
or » « to make the setting.  
v
Λ
<
>
7
Press » « (blue) to save the setting.  
  
note:  
7
If you wish to remedy other television  
channels, repeat steps 4 to 8.  
8- Press »menu« to end the setting.  
-47  
ENGLISH  
 
speCiAl-settinGs-----------------------------------------------------------------------------------------------------------  
entering-channel-names-(8-digit-  
maximum)  
Creating-lists-of-favourites  
You can select your favourite channels and  
save them in up to four favourites lists (Fav 1 to  
Fav 4).  
1
In the »PROGRAME TABLE« menu, select the  
television channel with » «, » «, » « or  
» « and press » «-(red) to confirm.  
v
Λ
<
>
1
2
3
In the »PROGRAME TABLE« menu, switch  
over to the list view with » « (yellow).  
  
2
Open the input keyboard with » « (green).  
  
Select the preferred channel with »  
or »Λ«.  
v«  
note:  
7
If necessary, delete the current channel  
name. To do this, select the »  
« button  
Use » « or » « to ”push“ the channel into  
<
>
with » « or » « and delete repeatedly using  
one of the favourites lists 1 to 4 and press  
»oK« to confirm.  
<
>
»oK«  
Select the required letters or numbers with  
«, » «, » « or » « and confirm with  
»oK«  
.
– The position in the favourites list is marked  
with »✔«.  
– You can enter the same channel in more  
than one favourite list.  
– Eachfavouritelistcanstoreupto255 chan-  
nels.  
3
4
»
v
Λ
<
>
.
Repeat the entry for further letters/numbers.  
note:  
7
Use the »ABC« button to switch to upper  
note:  
case letters and use the »?@123« button to  
switch to symbols and numbers.  
7
Channels can also be deleted from favour-  
ites lists. Select the channel to be deleted  
with »  
v«, »Λ«, » « or » « and delete it with  
Save the channel name by using »v«, »Λ«,  
<
>
»oK«  
.
» « or » « to select »Submit« and confirm  
<
>
with »oK«  
.
exiting-the-settings  
Press »menu« to end the setting.  
note:  
1
7
If you wish to enter other channel names,  
repeat steps 1 to 4.  
skipping-television-channels  
You can highlight television channels to be  
skipped when you select with »Λ« or »v«.  
Selection is still possible using the number  
buttons.  
1
2
3
In the »PROGRAMETABLE« menu, switch over  
to the list view with » « (yellow).  
  
Select the preferred channel with »  
v«  
or »Λ«.  
Select the column »Skip« with » « or » «  
<
>
and use »oK« to mark the channel.  
– The channel is marked using »✔«.  
note:  
7
Channels can also be reactivated. Select the  
channel with » « or » «, then select the  
v
Λ
column »Skip« and reactivate the channel  
with »oK«  
.
-48  
ENGLISH  
 
inFormAtion----------------------------------------------------------------------------------------------------------------------  
Displaying-signal-information  
(for digital channels only)  
service-information-for-retailers  
Only operate the television  
with the power supply/power  
cord provided.  
The product complies with the  
1
2
Open the menu with »menu«.  
Select the line »SOURCE SETUP« with »  
or »Λ« and press »oK« to confirm.  
v«  
following EU directives:  
2006/95/EC directive on electrical equipment  
for use within certain voltage limits.  
2004/108/EC directive on electromagnetic  
compatibility.  
2009/125/EC directive on ecodesign require-  
ments for energy-related products.  
Power consumption values and classes are speci-  
fied according to the regulations 2009/642 and  
2010/1062 and the standards EN62087 and  
EN62301 as per European Union framework di-  
rectives 2009/125/EC and 2010/30/EU  
3
Select the line »Signal Information« with  
« or » « and press »oK« to confirm.  
– Information on the channel, network,  
modulation, symbol rate, quality and  
signal strength is displayed.  
»v  
Λ
notes:  
7
The signal information changes in accord-  
ance with the current input source.  
7
The signal properties are displayed in the  
lower section of the menu. The further the  
bars for »Quality« and »Signal Strenght«  
extend to the right, the better the reception  
signal.  
environmental-note  
This product has been made  
from high-quality parts and  
7
The signal level not only depends on your  
receiver system, but also on the channel  
which is currently active. Remember this  
when aligning your antenna based upon  
the signal level display.  
materials which can be re-used  
and recycled.  
Therefore, do not dispose of the  
product along with normal household waste at  
the end of its service life. Take it to a collection  
point for the recycling of electrical and electronic  
equipment. Dispose of the used device at a collec-  
tion point for electrical and electronic equipment.  
The symbol on the product, in the operating man-  
ual or on the packaging indicates that recycling  
is possible.  
4
Press »menu« to close the menu.  
Information on collection points is available from  
your local authorities.  
Help protect the environment by recycling used  
products.  
-49  
ENGLISH  
 
inFormAtion----------------------------------------------------------------------------------------------------------------------  
preset-channels:-  
GrunDiG-46-vle-6220-BF  
TV/Radio  
1000 (Cable – DVB-C) or  
technical-data  
100 (Analogue)  
1000 (Terrestrial – DVB-T) or  
100 (Analogue)  
operating-voltage:-  
220–240 V, , 50–60 Hz  
~
8 AV, 1 USB  
power-consumption:  
On mode 82 W  
Standby <0.50 W  
screen-(dm²):  
58 dm²  
energy-efficiency-class:  
A
screen-size:  
117 cm/46 inch  
maximum-power-consumption  
Operational 180 W  
maximum-resolution:  
WUXGA, 1920 x 1080  
Annual-power-consumption  
weight:  
120 kWh  
approx.. 20 kg  
Audio-output:-  
2 x 20 W music power output  
2 x 10 W Sine wave power  
Dimensions:  
W H D 108,3 cm 66,6 cm 4,3 cm  
rohs-limits: Pb (Lead)/Hg (Mercury)  
Pb meets ROHS directive / 0 mg  
peak-luminance-ratio:  
% 65  
Digital-reception-ranges  
Cable:  
Overall band: 110 MHz – 862 MHz  
Modulation:  
16QAM, 32QAM, 64QAM,  
128QAM and 256QAM  
Symbol rate: 4.0 Msym/s to 7.0 Msym/s  
terrestrial-(DvB-t):  
VHF/UHF band, Bandwidth 7 MHz  
and 8 MHz  
FFT Size:  
Modulation:  
2k, 8k  
16QAM, 64QAM, QPSK  
Guard Interval: 1/4, 1/8, 1/16, 1/32  
terrestrial-(DvB-t2)-(*):  
VHF/UHF band, Bandwidth 7 MHz  
and 8 MHz  
FFT Size:  
Modulation:  
1k, 2k, 4k, 8k, 16k, 32k  
16QAM, 64QAM,  
256QAM, QPSK  
Guard Interval: 1/4, 19/256, 1/8, 19/128,  
1/16, 1/32, 1/128  
(*) As this feature is optional, it is not available  
in all products.  
Analogue-reception-ranges:  
C02 ... C80, special channels S01 ... S41  
Technical changes and errors reserved.  
-50  
ENGLISH  
 
inFormAtion----------------------------------------------------------------------------------------------------------------------  
troubleshooting  
If the information provided below does not help, please consult an authorised GRUNDIG dealer.  
Please bear in mind that malfunctions can also be caused by external devices such as video recorders  
or satellite receivers.  
problem  
possible-cause  
remedy  
Screen lit (snow), but no  
station visible  
Antenna cable  
Is the antenna cable connected?  
No TV channel tuned  
Start a channel scan  
Insufficient contrast in picture  
The picture settings are not correct  
Adjust the brightness, contrast or  
colour setting  
Problem at station  
Try another channel  
Picture and/or sound distorted Interference from other devices  
Place the device in a different position  
Ghosting, reflection  
No colour  
Channel setting  
Antenna  
Automatic or manual tuning/fine tuning  
Have antenna cable or system checked  
Turn up the colour  
Colour intensity too low  
Adjust TV standard (if setting option  
is available)  
Select the correct colour standard  
Problem at station  
Try a different channel  
Picture but no sound  
Volume is set to a minimum  
Turn up or switch on the volume  
Teletext impaired or absent  
Problem at station  
Try a different channel  
Television channel (no teletext)  
or antenna system  
Try with a different TV channel,  
carry out fine tuning  
Station signal too weak  
Check antenna  
The remote control does  
not work  
Obstacle between remote control  
and device.  
Point remote control at television  
Battery problem  
Check batteries and replace if  
necessary  
Operating mode undefined  
Switch off the television at the mains  
switch for two minutes  
Picture too dark in PC mode  
Incorrect setting for picture resolution Change settings on the PC  
and picture frequency on the PC  
(e.g. 1280 x 768 resolution,  
refresh rate 60 Hz)  
note:  
7
This is a Class A product. During operation the device could cause radio interference. In this case  
the user may have to remedy this. Please contact your specialist dealer.  
-51  
ENGLISH  
 

Graco Baby Accessories ISPC089BA User Manual
Grizzly Power Screwdriver H6191 User Manual
Harman DJ Equipment 1210KA User Manual
Hasbro Games 56223 55603 User Manual
Honeywell Scanner MS7320 InVista User Manual
Hotpoint Dishwasher BCI450 User Manual
Hotpoint Washer Dryer WMA40 User Manual
HP Hewlett Packard Car Stereo System 3490A User Manual
Hunter Fan Indoor Furnishings Illumi Heat User Manual
Impex Home Gym DBR 92 User Manual