Stand for
Drill / Mill
Machine
Model 42977
A s s e m b l y & O p e r a t i n g
I n s t r u c t i o n s
Stand shown with Drill / Mill machine (not included)
®
3491 Mission Oaks Blvd. / Camarillo, CA 93011
Copyright © 2000 by Harbor Freight Tools®. All Rights Reserved.
No portion of this manual or any artwork contained herein may be reproduced in any
manner, shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
REVISED 08/05
ASSEMBLYAND OPERATINGINSTRUCTIONS
Your machine stand is fully assembled when you
receive it. However, it must be attached to the floor,
and the machine must be mounted on it prior to
operation.
1.
Find a location for the stand within your
workshop. Select a location which has a sturdy,
level floor which is capable of supporting the
weight of the stand, machine to be mounted on it,
and any workpieces you intend to place on the
machine or stand.
2.
The location must also provide safe working
conditions, including adequate light and
ventilation, protection from water and weather,
and acess to an appropriate power supply for the
machine.
G
F
1
E
3.
4.
Locate the stand in an area that provides
adequate working room to manage the
workpieces, tools, equipment and supplies
needed to perform the intended operations.
Prepare the floor by leveling it, using cement,
steel plates, wooden reinforcements or other
suitable means.
A
D
2
3
C
B
Figure 1. Assembly Diagram
5.
6.
7.
Place the stand in its intended location, and mark the floor through the bolt holes in the flanges on the
corners of the base.
Depending on the floor material, drill bolt holes or install lag bolts in the floor. Secure these as
appropriate.
Reposition the stand on the prepared floor fastening system, and secure in place. Test the stand to be
sure it is permanently and securely attached before placing the machine on the stand.
Your Drill / Mill machine may include a tray which must be positioned between the machine and the
stand. Numbers shown below refer to the diagram in Figure 1.
1.
Place the tray (#5) (not included) on the stand, aligning the four holes in the corners with the mounting
holes on the upper flange of the stand.
2.
With the help of an assistant, place the machine on the tray, with the mounting holes in the machine base
(#6) (not included) aligned with the holes in the tray and the stand.
3.
4.
Fasten the machine securely to the stand, using four bolts (#7), washers and nuts (not included).
Check to be sure the machine is securely mounted before connecting the power cord, or turning it on.
NOTE: Some parts are listed and shown for illustration purposes only
and are not available individually as replacement parts.
Page 3 SKU # 42977
#42977 DRILL / MILL MACHINE STAND PARTS DIAGRAM
P/N DESCRIPTION
1
2
3
4
Body
Door
Hinge
G
F
1
Door HandleAssembly
A B C D E F
E
A
D
DOOR HANDLE
ASSEMBLY
P/N DESCRIPTION
2
3
C
B
A
B
C
D
E
F
Bolt
Spring
Handle
Sleeve
Door Holder
SpringWasher
Nut
G
MAINTENANCE
Keep the stand wiped down and clean.
Do not allow the stand to remain wet, and do not allow standing water to accumulate around the base.
Use applications of light grease or paint to any unpainted surfaces to prevent rust.
Check the floor mounting bolts and machine mounting bolts monthly to assure that they remain securely
fastened. Retighten or replace any fastening hardware as needed.
1.
2.
3.
4.
WARNING!
USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool or attachment to do the work
of a larger industrial tool. There are certain applications for which this tool was designed. Do not modify this tool
and do not use this tool for a purpose for which it was not intended.
PLEASE READTHE FOLLOWINGCAREFULLY
THE MANUFACTURERAND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUALASA
REFERENCE TOOLONLY: NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKESANYREPRESENTATION
OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO
THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACEANYPARTS OF THE PRODUCT: IN FACTTHE
MANUFACTURER A ND/OR DISTRIBUTOR EXPRESSLY STATES THATALL REPAIRS AND PARTS
REPLACEMENTS SHOULD BE UNDERTAKEN BYCERTIFIEDAND LICENSED TECHNICIANSAND NOT BYTHE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITYARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINALPRODUCT OR REPLACEMENT PARTS THERETO, ORARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
REV 09/06
Page 4 SKU # 42977
|