Havis Shields Automobile Accessories KK K9 F12 K User Manual

INSTALLATION INSTRUCTIONS KK-K9-F12-K  
2000-2006 FORD EXCURSION  
TOOLS REQUIRED:  
Power Drill  
Ratchet Wrench With 6” Extension  
Torx Bit Set  
4 ½” Hole Saw (Exhaust Fan Option)  
Caulk Gun  
Standard & Metric Socket Sets  
Phillips Screw Driver  
7/16” Wrench  
Wire Cutters / Crimping tool  
HARDWARE: Some of this hardware is already attached.  
QTY: DESCRIPTION:  
PART #:  
28  
30  
64  
6
14  
36  
24  
22  
6
¼-20 X ½” Stainless carriage bolts  
¼-20 X ¾” Stainless carriage bolts  
¼-20 Serrated nuts  
GSM 32022  
GSM 32024  
GSM 30023  
GSM33001  
GSM 33062  
GSM 34177  
GSM 34170  
GSM 34169  
GSM 33195  
GSM33194  
PRM 97343  
KNM01029-SUV  
¼-20 X ¾” Hex head Cap Screw Zinc  
¼” X 1 ½” Hex head lag screw  
#12 X ¾” Stainless sheet metal screws  
#10 X ¾” Stainless sheet metal screws  
#10 X ½” Stainless sheet metal screws  
#10 X ¾” Sheet metal screws  
#10 X ½” Sheet metal screws  
Tube Silver Caulk  
20  
1
1
46” X 45 1/2” Rubber Mat  
11 1/2 feet Adhesive Molding  
SUB ASSEMBLY:  
Dome light with wire  
Tunnel edge molding  
Install exhaust fans (Optional). If locating in custom  
location drill 4 ½” hole into desired location of K-9  
housing. Mark and drill 3/16” mounting holes to  
attach fan using (4) 10/32” X ½” machine screws and  
10/32” keps nuts. Then mark and drill 3/16” holes to  
mount fan guard using 10/32” X ½” machine screws  
and 10/32” keps nuts.  
INSTALLATION:  
1. Remove interior:  
Remove rear seats  
Remove rear seat belt assembly  
Remove top, and bottom plastic rear trim caps  
 
7. Door panels and window guards:  
Center door panels so edges do not hang over.  
Attach to door with #10 x ½” stainless sheet metal screws.  
Note: window guards have holes around perimeter for permanent mounting. These holes are not used  
with hinge kit! They also come flat in shipping. The guard must be pre-bent so it fits tight against the door  
window frame.  
Hold window guard with pre-assembled hinge and upper bracket onto window frame.  
Make sure guard is centered on window.  
Attach hinge to lower door panel with #10 x ½” sheet metal screws.  
Mark upper aluminum bracket location on  
window frame and remove from window guard.  
Attach aluminum bracket onto window frame with  
#10 x ½” sheet metal screws.  
Apply adhesive molding to inner side of window  
guard.  
Hinge up window guard and reattach to bracket  
Upper Window Bracket  
with #10 x ½” stainless machine screws and #10  
stainless flat washers.  
Note: this is for easy window cleaning.  
8. Final steps:  
Mount dome light (fan if necessary) switch box as  
desired. A switch box is provided so switch can  
be mounted to K-9 housing in various locations.  
(Topside of tunnel housing works very well).  
Wire to 12-volt power source.  
Sheet metal seams and gaps need to be carefully  
silicone at floor area. Proper sealing of  
compartment will eliminate water from getting  
Adhesive Molding  
under the K-9 unit.  
Allow silicone to dry overnight before placing in  
rubber floor mat.  
KK-K9-F12-K-INST-6-06  
 

Graham Field Baby Accessories 14423 2 User Manual
Grundig CRT Television LW 60 7510 TOP User Manual
Haier Washer MCS10HXCR User Manual
Hamilton Beach Microwave Oven 87108 User Manual
Hamilton Beach Oven 31160 User Manual
Hamilton Beach Slow Cooker 840149601 User Manual
Honeywell Telephone W8735B User Manual
Honeywell Thermostat TL8100 User Manual
Humax Flat Panel Television LGB 19DZT User Manual
Ice O Matic Ice Maker ICE1606 User Manual