/
Rev 0 03 18
P/N:3810-0071G
USER INFORMATION:
CAUTION
Design and specifications
are subject to change
without notice.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
SPECIFICATIONS:
Series
HD40
Explanation of two Symbols
Signal System
NTSC : 525 Lines
PAL : 625 Lines
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of un-insulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
Scanning System
Scanning Frequency (H)
Scanning Frequency (V)
Image Sensor
Total/Effective Pixels No.
S/N Ratio
2 : 1 Interlace
Operation
Manual
15.734kHz
59.94Hz
1/3 inch SONY Super HAD CCD
270K/250K 320K/290K
15.625kHz
50Hz
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance-
(servicing) instructions in the literature accompanying the appliance.
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM
OF THE SYSTEM.
"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT
TO RAIN OR MOISTURE"
More than 48dB
380 TV Lines
1.0 Vp-p (75 Ohms, composite)
Fixed Lens (f=3.8mm)
Manual
• 1/3” SONY Super HAD CCD
• 380 TV Lines Resolution
• Built-in Fixed Lens (f=3.8mm)
• Min. Illumination : 0.1 Lux
• Auto White Balance
Resolution
Video Output Level
Lens- Mirror Cover
Focus
Sync. System
Sensitivity
Electronic Shutter
White Balance
AGC
Input/Output Connector
Power Consumption
PRECAUTION:
!
Internal
0.1 Lux
All the warnings and instructions of this manual should be followed.
• Diameter of Bubble : 85mm
• Easy Install (3-Axis)
Remove the plug from the outlet before cleaning. Do not use liquid
1/60~100,000 Sec.
1/50~100,000 Sec.
aerosol detergents. Use water damped cloth for cleaning.
To reduce the risk of fire or electric shock, do not expose this appliance
to rain or moisture.
Do not place anything on top of the unit that might spill or fall into it.
Do not attempt to service this unit yourself as opening or removing
covers may you to dangerous voltage or other hazards. Please refer
all servicing to qualified service personnel.
Auto
Auto
Power (Red Jack), Video (Yellow Jack)
12VDC (10V~15V), 0.15A / 1.8W (Max)
85mm
t
READ AND KEEP THIS
OPERATION MANUAL
(
)
Ø
Dome Size
Weight
Keep enough space around the unit for ventilation.
Slots and openings on the monitor should not be blocked.
Approx. 210g
During flashes of lightning or cracks of thunder, or when the system
is not used for a long time, unplug the system power supply to
protect the unit from lightening or power surges.
Need Help?
Call 1.800.796.CCTV for sales, service and customer support.
90º
INSTALLATION:
COMPOSITION:
3
-axis
Built-in
camera
Tilt
bracket makes it much
easier to rotate in any
direction.
This manual explains the installation and operating method for the
color dome camera. Before installation, make sure you are familiar
with this product's special features and proper operating technique.
360º
Dome Camera
Guide Pattern
Horizontal
Pan
360º
Stick the guide pattern on the wall or ceiling.
1
Ceiling
Mounting Screw
Operation Manual
Drill two holes according to the guide pattern
TROUBLESHOOTING:
2
then insert anchors into the drilled holes.
Guide Pattern
If you have trouble operating
your camera, refer to the following.
Draw out power/video wires to the connecting
places.
CONNECTION:
3
If the guidelines do not enable you to solve the problem,
contact an authorized technician.
Dome Base
•The wire is polarized.
12VDC Power Type
Fixed the camera to a celling using two screws.
4
5
•Use 12VDC power source.
Check the power source for the monitor
and camera and ensure that the voltage
and polarity are properly connected and
being supplied correctly.
The image does not
appear on the screen.
#
1
Video
(Yellow)
Video Output
GND
Adjust desired focus and scene by turning
and moving the 3-axis camera bracket by
hand.
No. Function Terminal Color
#1 Video Output Yellow
Remark
Mounting
Screw
1.0 Vp-p
Check if the lens is stained. If dirty,
clean the lens with a soft, clean cloth.
Adjust the Back Focus of the lens again.
The image on the
screen is dim.
12VDC(10V~15V),
Put the dome cover over the base.
Power - 12VDC
(Red)
#2 Power Input
Red
6
7
1.8W(Max)
#
2
Fix the dome cover on the base by covering.
Check if you have connected the camera
to a proper power source and If there is
no problem with the power, turn the unit
off immediately and seek assistance from
our Customer Service department.
The camera does not
work properly, the surface
of the camera case is hot,
and a black line appears
on the screen.
DIMENSIONS:
Dome Cover
4.45”
(113 mm)
NOTE
Check if the camera is pointed toward
the sun or a fluorescent lamp.
Adjust the angle or location of the
camera if too much light is coming into
the screen.
The screen blinks a lot.
Insert coin to the side
hole and remove the
dome cover by twist coin.
3.35”
(85 mm)
3.35”
(85 mm)
|