Hotpoint Microwave Oven BD32 Mk2 User Manual

Instructions for Installation and Use  
Build-in Electric double oven  
DY46 Mk2  
BD42 Mk2  
BD32 Mk2  
To the Installer:  
Before installation, fill in the product details on the back cover of this book.  
The information can be found on the rating plate.  
To the User:  
You must read the instructions prior to installing and using the appliance and  
then retain them for future reference.  
 
Introduction  
Your new appliance is guaranteed* and will give lasting service. This guarantee is only  
applicable if the appliance has been installed in accordance with the installation  
instructions detailed in this booklet.  
To help make best use of your cooking equipment, please read this booklet carefully.  
The appliance is designed specifically for domestic use and responsibility will not be  
accepted for use in any other installation.  
When the cooker is first used an odour may be emitted,  
this will cease after a period of use  
To help remove the ‘new’ smell, heat up the empty ovens to maximum temperature for a  
minimum of two or three hours, keeping the oven doors closed. Ensure that the room is  
well ventilated (e.g. open a window or use an extractor fan) and that persons who may be  
sensitive to the odour avoid any fumes.  
It is suggested that any pets be removed from the room until the smell has ceased.  
This odour is due to temporary finish on oven liners and elements and also any moisture  
absorbed by the insulation.  
* The guarantee is subject to the provisions that the appliance:  
(a) Has been used solely in accordance with the Users Instruction Book.  
(b) Has been properly connected to a suitable supply voltage as stated on the  
rating plate attached to this equipment.  
(c) Has not been subjected to misuse or accident or been modified or repaired by  
any person other than the authorised employee or agent.  
(d) Has been correctly installed.  
This appliance conforms to the following EEC Directives:  
Electromagnetic Compatibility Low Voltage Equipment  
89/336/EEC  
92/31/EEC  
93/68/EEC  
73/23/EEC  
93/68/EEC  
3
 
Safety Information  
When used properly your appliance is completely safe but as with any electrical  
product there are certain precautions that must be observed.  
PLEASE READ THE PRECAUTIONS BELOW BEFORE USING YOUR APPLIANCE.  
Always  
Always make sure you remove all packaging and literature from inside the  
G
oven and grill compartments before switching on for the first time.  
Always make sure you understand the controls prior to using the appliance.  
G
Always keep children away from the appliance when in use as the surfaces  
G
will get extremely hot during and after cooking.  
Always make sure all controls are turned off when you have finished cooking  
G
and when not in use.  
Always stand back when opening an oven door to allow any build up of steam  
G
or heat to disperse.  
Always use dry, good quality oven gloves when removing items from the  
G
oven/grill.  
Always take care to avoid heat/steam burns when operating the controls.  
G
Always turn off the electricity supply at the wall switch before cleaning and  
G
allow the appliance to cool.  
Always make sure the shelves are in the correct position before switching  
G
on the oven.  
Always keep the oven and grill doors closed when the appliance is not in use.  
G
Always take care when removing utensils from the top oven when the main  
G
oven is in use as the contents may be hot.  
Always keep the appliance clean as a build up of grease or fat from cooking  
G
can cause a fire.  
Always follow the basic principles of food handling and hygiene to prevent  
G
the possibility of bacterial growth.  
Always keep ventilation slots clear of obstructions.  
G
Always refer servicing to a qualified appliance service engineer.  
G
During use the oven becomes hot. Care should be taken to avoid touching  
G
heating elements inside the oven,  
SAFETY ADVICE  
IN THE EVENT OF A CHIP PAN OR ANY OTHER PAN FIRE:  
1. TURN OFF THE COOKER APPLIANCE AT THE WALL SWITCH.  
2. COVER THE PAN WITH A FIRE BLANKET OR DAMP CLOTH, this will smother  
the flames and extinguish the fire.  
3. LEAVE THE PAN TO COOL FOR AT LEAST 60 MINUTES BEFORE MOVING IT.  
Injuries are often caused by picking up a hot pan and rushing outside with it.  
NEVER USE A FIRE EXTINGUISHER TO PUT OUT A PAN FIRE as the force of  
the extinguisher is likely to tip the pan over. Never use water to extinguish  
oil or fat fires.  
4
 
Safety Information  
Never  
Never leave children unsupervised where a cooking appliance is installed as  
G
all cooking surfaces will be hot during and after use.  
Never allow anyone to sit or stand on any part of the appliance.  
Never store items above the appliance that children may attempt to reach.  
Never remove the oven shelves whilst the oven is hot.  
Never heat up unopened food containers as pressure can build up causing  
the container to burst.  
G
G
G
G
Never store chemicals, food stuffs or pressurised containers in or on the  
appliance, or in cabinets immediately above or next to the appliance.  
Never operate the grill with the door closed as this will cause the appliance  
to overheat.  
G
G
Never use the appliance as a room heater.  
Never use the grill to warm plates.  
Never dry any items on the oven doors.  
Never install the appliance next to curtains or other soft furnishings.  
Never allow children to play with the appliance controls.  
Never use ‘steam cleaners’.  
G
G
G
G
G
G
5
 
The main parts of your Double Oven  
WARNING: DO NOT TOUCH THE GLASS DOORS WHEN THE OVEN IS IN USE AS THESE  
AREAS CAN BECOME HOT.  
Top Oven Temperature Control  
Main Oven Temperature Selector  
Timer  
Grill Control  
❍ ❍  
❍ ❍ ❍ ❍ ❍ ❍  
Grill/top oven  
element  
Stay Clean  
side liner  
Oven Light  
Grill pan &  
Food  
support  
Oven Shelf  
Inner Door Glass  
Top Oven Door  
Stay Clean back panel  
Oven Light  
Stay Clean  
side liner  
2 Oven Shelves  
Oven Fan  
Meat Pan  
(NOT ALL MODELS)  
Model & Serial number  
Inner Door  
Glass  
Main Oven Door  
Door Handle  
NEVER line the shelves, floor or sides of the oven or grill with aluminium foil as  
overheating and damage may result.  
6
 
The Cooking Systems in your Double Oven  
Your new oven is equipped with  
three different cooking systems:  
1. Conventional Heating  
1
(Top Oven) - with upper and  
lower heat. This system is  
particularly suitable for roasting  
and baking on one shelf only.  
2. Grilling (Top Oven) - Has a full  
width, fully controllable grill. The  
grill also has an economy setting  
which enables you to use just the  
left section.  
2
NOTE: The oven door should  
be open when grilling.  
(See page 17.)  
3. Fan Cooking (Lower Oven) - the fan  
oven operates by constantly blowing  
heated air from an element wrapped  
around the fan into the oven. This gives  
improved efficiency and, in general,  
enables the use of lower temperatures  
for cooking. It also means that there is  
less need to be particular about shelf  
positions and that you can bake at  
more than one level simultaneously  
(Batch Baking).  
3
It should be noted that at the end of a cooking period there may be a momentary puff of  
steam when the oven door is opened. This will disperse in a few seconds and is a  
perfectly normal characteristic of an oven with a good door seal.  
7
 
Temperature Conversion Chart  
The chart below gives details of comparisons of oven settings for gas conventional ovens  
and fan oven in degrees ˚F and ˚C  
GAS  
MARK  
CONVENTIONAL  
OVEN  
FAN  
OVEN  
˚F  
˚C  
˚C  
1
2
/
250  
275  
300  
325  
350  
375  
400  
425  
450  
475  
120  
140  
150  
160  
180  
190  
200  
220  
230  
240  
100  
120  
130  
140  
160  
170  
180  
200  
210  
220  
1
2
3
4
5
6
7
8
9
8
 
Controls  
GRILL SETTING CONTROL  
MAIN OVEN TEMPERATURE AND FUNCTION CONTROL  
TIMER  
A
B
C
TOP OVEN TEMPERATURE CONTROL  
CONTROL MARKINGS  
Control  
Knob  
Description  
Function  
Selects the heat at which the grill will cook the food.  
A
Grill Setting Control  
Grill Control Settings:  
1 = Low, 4 = High (BD32/42)  
MIN - MAX (DY46)  
Selects the cooking temperature  
(Degrees Centigrade) when using  
the top oven as a conventional oven.  
100 - 220  
or MAX  
B
Top Oven Temperature  
Control  
Fan Only Setting  
- This is used to decrease the amount  
of time required to defrost food  
items.  
Fan  
Only  
or  
or  
Oven Light Only  
- Switches on the Main Oven Interior  
Light Only.  
Oven  
Light  
C
Main Oven Temperature &  
Function Control  
Main Oven Temperature Scale  
(In Degrees Centigrade).  
- When cooking select the required  
cooking temperature.  
80 - 230  
or MAX  
Cooling Fan:  
Note:  
A gentle flow of air will be blown below the control panel when the grill  
control is used and after a short period of time when the ovens are used.  
Whenever the appliance has been used, the cooling fan may run on or  
restart itself after all the controls have been turned off. This indicates  
that the appliance is still warm.  
Oven Interior The oven lights are operated when their respective oven control is used.  
Lights  
(N.B. Not all models have a top oven interior light).  
The main oven has a light only position.  
Slow Cooking The main oven has a “Slow Cook Setting” this can be used for slow  
cooking, keeping food warm and warming plates for a short period.  
Note: It is advisable to check that all oven controls have been switched off when  
you have finished using the appliance.  
9
 
Oven Timer Operation  
Note: Timer must be set to ‘Time of Day’ and ‘Manual’ before the ovens  
can be used.  
AUTOMATIC COOKING  
The Top Oven and Main Oven can be controlled by the automatic timer. When the  
timer control has been set for one oven, it is possible to use the other oven only  
during the same automatic cooking programme.  
NEVER operate the grill when the ovens are set to cook automatically  
because the oven cavity can become warm and this may cause  
bacterial growth in food.  
HINTS ON AUTOMATIC COOKING  
1. Select foods which will require the same cooking time and temperature.  
2. To ensure food does not cool down and require reheating, set the end time  
so the food is ready when you require it.  
3. Always ensure that meat and poultry is defrosted before placing in the oven.  
4. Whenever possible, take food out of the refrigerator and keep it as cool as  
possible.  
5. If cooking food that requires frying before placing in the oven for auto  
cooking, keep the delay start time to a minimum.  
6. Never place hot or warm food in the oven for delay start cooking as it could  
cause the oven to be warm and produce harmful bacteria in the food.  
7. We advise that dishes containing left-over cooked poultry or meat, e.g.  
Shepherd's Pie, should not be cooked automatically if there is to be a delay  
period.  
8. Ensure that delay start times are kept to a minimum to prevent bacterial  
growth in food.  
9. Wine or beer may ferment and cream may curdle during the delay period so it  
is best to add these ingredients just before serving.  
10. Foods which discolour should be protected by coating in fat or tossing in  
water to which lemon juice has been added, prior to placing food in the oven.  
11. Dishes containing liquid should not be filled too full to prevent boiling over.  
12. Food should be well sealed (but not airtight) in a container to prevent the  
loss of liquid during cooking. Aluminium foil gives a good seal.  
13. Always ensure that food is piping hot and cooked thoroughly before serving.  
14. Only reheat food once.  
10  
 
Know Your Timer  
CLOCKFACE  
The timer incorporates a 24 hour clock.  
Ensure the correct time of day is always set, before using your cooker.  
SYMBOLS  
A ‘bell’ symbol will light up when you select a Minute Minder Period and will  
remain lit for the period set.  
At the end of the Minute Minder Period, the timer will emit an audible tone  
and the ‘bell’ symbol will disappear.  
The ‘cookpot’ symbol will light up either:–  
When the timer is in manual mode, or  
During the actual Cook Period.  
‘AUTO’ will light up:–  
When the timer is first turned on it will flash. It will go out when a time  
of day is set or when the timer is set to manual.  
The ‘AUTO’ symbol will flash at the end of an Auto Cooking programme to  
indicate that the programme has finished.  
(When the ‘AUTO’ symbol is flashing, tto return the oven to Manual operation,  
turn the oven controls off, ensure tthat the correct time of day is set, and  
press the “Manual” button – The ‘AUTO’ symbol will go out).  
TIMER FUNCTION BUTTONS  
Minute Minder  
Button  
Here you can set a time period of up to 23 hours 59 minutes, that will count  
down. When it reaches zero, the timer will emit an audible tone.  
For Example: If you set 20 minutes, the audible tone will occur 20 minutes later.  
AUTO COOKING PROGRAMME  
Cook Period  
Button  
Cook Period is the actual length of time for which, the timer will switch the  
oven(s) on as part of an “Auto Cooking” programme.  
(e.g. If you set 2 hours, the food will be cooked for 2 hours).  
End Time Button  
The time of day at which you want an “Auto Cooking” programme to end.  
For Example: If you set a “Cook Period” for 2 hours, and “End Time” of 11:00.  
The timer will switch the oven(s) on at 9:00 and turn the oven(s) off at 11:00.  
You will hear an audible tone at 11:00, to indicate that the Auto Cooking  
Programme has finished.  
Notes:  
-
When setting an Auto Cooking programme you will need to set the oven  
control(s) to the required temperature(s) when you set the timer.  
If an Auto Cooking programme has been set the oven(s) will only operate  
during the pre-programmed time.  
-
Needs to be pressed to cancel an Auto Cooking programme and return the  
oven(s) to Manual operation.  
Manual Button  
“+” and “–” Buttons Used to adjust the various timer function settings.  
11  
 
Electronic Clock & Automatic Oven Timer  
Operation  
SETTING THE TIME OF DAY  
Step 1 Make sure all oven controls are turned Off.  
Step 2 Check the electricity supply to the cooker is turned on.  
Step 3 When switched on the display will show 0.00 and the Auto symbol,  
flashing intermittently.  
Step 4 Press & hold in both the Cook Period & End Time buttons together.  
Step 5 With the Cook Period & End Time buttons still held in, press either  
the “+” or “–” buttons to set the correct time of day.  
Step 6 Release all the buttons simultaneously.  
THE TIME OF DAY IS NOW SET.  
To change the time of day rrepeat Steps 44, 5 & 6 above.  
Note: You cannot adjust the time of day if the timer has been set for an  
Auto Cooking Programme.  
SETTING THE MINUTE MINDER  
Step 1 Ensure the time of day is set correctly.  
Step 2 Press and hold the Minute Minder button.  
Step 3 With the Minute Minder button held in, set the required Minute  
Minder period using the “+” and “–” buttons. A ‘bell’ symbol will light  
up.  
Release all buttons and the timer display will revert back to the time of day.  
The ‘bell’ symbol will remain lit to signify that a Minute Minder period has  
been set.  
At the end of the set time an audible tone will be heard, and the ‘bell’ symbol  
will disappear.  
Step 4 To cancel the audible tone press the Minute Minder button.  
Note 1 When the Minute Minder has been set, the time remaining can be checked at any  
time by simply pressing the Minute Minder button.  
Note 2 If necessary the Minute Minder can be cancelled before the tone sounds by  
pressing and holding the Minute Minder button and then at the same time  
pressing the “–” button until 0.00 appears in the display window.  
12  
 
Electronic Clock & Automatic Oven Timer  
Operation  
AUTO COOKING PROGRAMMES  
There are two Auto Cooking programmes that can be selected using your timer:–  
(a) To set the timer to switch the oven(s) On and Off Automatically  
(b) To set timer to switch on immediately and OFF automatically after a set cook period.  
a) TO SET THE TIMER TO SWITCH THE OVEN(S) ON AND OFF AUTOMATICALLY  
This allows you to cook at a specified time for a chosen period before the oven switches  
off Automatically.  
Step 1 Check that the correct time of day is set, if not follow instructions for setting the  
time of day.  
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).  
Step 3 Press and hold in the Cook Period button.  
The display will read 0.00 with the ‘cookpot’ symbol lit.  
Step 4 With the Cook Period button still held in, set the required Cook  
Period using the “+” and “–” buttons.  
Release the buttons and the timer display will revert to the time of day with  
the ‘Auto’ symbol and ‘cookpot’ symbol lit.  
Step 5 Press and hold in the End Time button.  
The display will read the earliest possible end time for the Cook  
Period that you have set above.  
The ‘Auto’ symbol and ‘cookpot’ symbol will be lit.  
Step 6 With the End Time button still held in, use the “+” and “–” buttons to  
set the ‘End Time’ (i.e. The time you require the oven to switch off).  
Release all the buttons and the timer will revert back to the time of day.  
The ‘Auto’ symbol will remain lit to signify that an Auto Cooking Programme  
has been set. The ‘cookpot’ symbol will go out.  
Step 7 Turn the oven control(s) to the required temperature, and if  
necessary select the appropriate oven function.  
Note: If your appliance has two ovens: When the timer has been set for one  
oven it is possible to use the other oven only during the same Automatic  
programme.  
At the end of the Automatic Cook Period the Auto Symbol will flash and an  
intermittent bleeping sound will be heard.  
The audible tone will continue unless cancelled.  
The ‘Auto’ symbol will continue to flash until the timer is returned to Manual  
operation (see below).  
Step 8 Press the Manual button, the audible tone will be cancelled and the  
oven(s) will be returned to Manual.  
Step 9 Turn the oven control(s) to the OFF position.  
13  
 
Electronic Clock & Automatic Oven Timer  
Operation  
Note 1 When cooking automatically the Cook Period can be checked at any time by  
simply pressing the Cook Period button.  
Note 2 When cooking automatically the End Time can be checked at any time by simply  
pressing the End Time button.  
b) TO SET TIMER TO SWITCH ON IMMEDIATELY AND OFF AUTOMATICALLY AFTER A SET  
COOK PERIOD  
Step 1  
Check that the correct time of day is set, if not follow instructions for setting the time of  
day.  
Step 2  
Step 3  
Place food onto the correct shelf position in the oven and close the oven door(s).  
Turn the oven control(s) to the required temperature, and if necessary select the  
appropriate oven function.  
Step 4 Press & hold in the Cook Period button, the display will read 0.00 and  
the ‘cookpot’ symbol will light up.  
With the Cook Period button still held in set the required Cook Period using  
the “+” and “–” buttons. Example: 1hr 30 minutes (as shown).  
Note: Cook Period is the length of time the food requires to cook.  
Step 5 Release all buttons.  
The timer display will revert to the time of day with the ‘Auto’ symbol lit &  
‘cookpot‘ symbol remaining lit.  
NOTE: The Cookpot  
symbol disappears  
At the end of the Cook Period the ‘Auto’ symbol will flash and an intermittent  
audible tone will be heard.  
The audible tone will continue until cancelled.  
The ‘Auto’ symbol will continue to flash until the timer is returned to Manual  
operation (see below).  
Step 6 Press the Manual button. The audible tone will be cancelled and the  
oven(s) will be returned to Manual.  
Step 7 Turn the oven control(s) to the OFF position.  
14  
 
Electronic Clock & Automatic Oven Timer  
Operation  
TO CANCEL AN AUTO COOKING PROGRAMME BEFORE  
THE COOK PERIOD HAS FINISHED.  
Step 1 Turn the oven control(s) to the OFF position.  
Step 2 Press the Manual button to return the oven(s) to “Manual”  
operation.  
The ‘Auto’ symbol will go out.  
Note 1  
When cooking automatically the Cook Period can be checked at any time by simply pressing  
the Cook Period button.  
OTHER NOTES ON TIMER OPERATION  
1. When cooking Automatically the Cook Period can be checked at any time simply by pressing the  
Cook Period button.  
2. When cooking Automatically the End Time can be checked at any time by simply pressing the End  
Time button.  
3. Having set a Cook Period and End Time an electronic device stores the information. The device  
within the timer will switch the oven(s) on and off at the required times.  
4. When setting an Auto Cooking Programme and a mistake is made, to clear:–  
(a) Press & release the Manual button.  
(b) Start the sequence again.  
5. If at any time the display shows three flashing zero’s 0.00 and ‘Auto’, it is likely that the electricity  
supply to the oven has been interrupted. Reset the timer to the correct time of day.  
Food in the oven may, therefore, not have been cooked, before serving check food is thoroughly  
heated and completely cooked.  
6. To set each function always press and hold the required function button and at the same time  
press “+” or “–” buttons.  
15  
 
Grill Pan and Handle  
The grill pan handle is detachable from the pan, to facilitate cleaning and storage.  
The grill pan handle can be fixed as follows:  
(d)  
(a)  
(c)  
(b)  
Step 1  
Step 2  
Step 3  
St
Step 1 Remove the screw and washers from the grill pan bracket (a).  
Step 2 Tilt the handle over the recess (b).  
Step 3 Slide it towards the centre of the pan (c).  
Step 4 Locate the handle over the bracket (d).  
For a fixed handle, replace the screw and washers and ensure they are  
fully tightened up. If a detachable handle is required, do not replace the  
screw and washers.  
Note: If a fixed handle is required, the grill pan cannot be kept in the main oven with the  
door closed but may be stored in the top oven with the door closed, when the top oven  
is not in use..  
Grill Pan and Food Support  
FOOD SUPPORT  
GRILL PAN  
Top Oven Shelf Positioning for Grilling  
ENSURE SHELVES ARE FITTED CORRECT WAY UP.  
3
2
1
3
2
1
DO NOT PLACE FOOD/UTENSILS DIRECTLY ON THE OVEN FLOOR  
NOTE:  
- Preheat the grill if indicated on grill chart.  
- The grill pan must be placed on the correct shelf and positioned centrally under the  
grill element.  
- Leave the control at 4 or MAX (depending on Model) for toast, and for fast cooking  
of foods.  
- For thicker foods requiring longer cooking, turn the switch to a lower setting after  
the initial sealing on both sides at 4 or MAX (depending on Model). The thicker the  
food, the lower the control should be set.  
- DO NOT line the grill pan with aluminium foil, as this increases the amount of fat  
spitting which can cause a fire.  
- After use always return both controls to their OFF (0) position.  
16  
 
Operation when using the Top Oven for Grilling  
GRILL SETTING CONTROL  
TIMER  
A
C
B
TOP OVEN TEMPERATURE CONTROL  
Step 1 Ensure oven timer is set to manual.  
Place the shelf in the correct position (see Grilling Guide).  
Place the food/grill pan on the shelf, positioned centrally under the grill  
element.  
Leave the top oven door fully open.  
Step 2 Turn knob (A), clockwise for FULL grill or anti-clockwise for HALF grill, to  
select the grill setting MIN (1) – MAX (4).  
NOTE: MIN (1) = Low, MAX (4) = High.  
Grill Controls Example:  
OR  
4
MAX  
= High Grill Setting (depending on model)  
4
MAX  
OR  
NOTE: Do not grill with the grill/top  
oven door closed.  
Step 3 After use, turn the grill control (A)  
to the off position (0).  
DO NOT allow young children near to the appliance when the grill is in use as the surfaces  
get extremely hot.  
17  
 
18  
 
Using the Top Oven as a Convection Oven  
The top oven should be used to cook small quantities of food. The oven is  
designed so that the grill element operates at a reduced heat output, this is  
combined with a heating element situated underneath the floor of the oven. To  
ensure even cooking of the food it is important that cooking utensils are  
positioned correctly on the oven shelf so that the element is directly above. As a  
guide, the front of the utensil should be approx.100mm (4”) from the front of  
the shelf.  
Note: Charts are a guide only, to suit personal taste and requirements, it may be  
necessary to increase or decrease temperatures by 10˚C. It may also be necessary to  
increase or decrease cooking times.  
SHELF POSITIONING  
ENSURE SHELVES ARE FITTED THE CORRECT WAY UP  
3
2
1
DO NOT PLACE FOOD/UTENSILS DIRECTLY ON THE OVEN FLOOR  
There should always be at least 25mm (1 inch) between the top of the food and  
the grill element.  
WARNING: Items stored in the top oven will get hot when the main oven is in use.  
DO NOT allow young children near to the appliance when the top oven is in use as the  
surfaces get extremely hot.  
19  
 
Operation when using the Top Oven  
as a Convection Oven  
A
B
C
❍ ❍  
TIMER  
TOP OVEN TEMPERATURE CONTROL  
Step 1 Check that the timer is in manual.  
Step 2 Place the shelf in the correct position (see Oven Temperature Charts).  
Step 3 Select the required cooking temperature, (100–220˚C or MAX depending  
on Model) using control (B) (see Top Oven Temperature Charts).  
The pilot light ( G ) will immediately come on, and remain on until the oven  
reaches the required temperature. The light will then automatically go off  
and on during cooking as the oven thermostat maintains the correct  
temperature.  
Step 4 Place the food centrally on the shelf below the element ensuring the oven  
door is closed.  
NOTE: At the end of your cooking, always return control (B) to the OFF (O)  
position.  
PLATE WARMING  
Place the plates/dishes on shelf position 1 from the base of the top oven, and turn  
top oven temperature control (B) to 100˚C for 10-15 minutes.  
Never use the grill setting control (A) when warming plates.  
TOP OVEN UTENSILS  
Do Not use: Meat Pans and Baking Trays larger than – 225mm x 300mm (9”x12”)  
DO NOT use the grill pan or main oven meat pan as a meat pan in the top oven, as the  
air circulation will be seriously restricted.  
20  
 
21  
 
22  
 
Using the Main Oven for Fan Cooking  
Since a circulaire fan oven heats up more quickly and generally cooks food at a  
lower temperature than a conventional oven, pre-heating is often unnecessary. For  
guides on ‘pre-heating’, ‘cooking temperatures’ and ‘cooking times’ see “Oven  
Temperature Charts” later in this book.  
Note:  
Charts are a guide only, to suit personal taste and requirements, it may be  
necessary to increase or decrease temperatures by 10˚C. It may also be  
necessary to increase or decrease cooking times.  
MAIN OVEN SHELF POSITIONING FOR FAN OVEN  
Most foods will cook satisfactorily on any shelf position, due to even distribution of  
heat in the main oven, but the shelves must be evenly spaced.  
The top oven rod shelf can be used in the main oven when cooking large quantities  
of food. (NB. Maximum 3 shelves in the main oven).  
Food or utensils should never be placed directly on the floor of the oven for cooking.  
DO NOT allow young children near to the appliance when the main oven is in use as the  
surfaces get extremely hot.  
MAIN OVEN UTENSILS  
DO NOT use:  
Meat Pans larger than  
Baking Trays larger than  
-
-
375mm x 300mm (15"x12")  
325mm x 250mm (13"x10")  
TEMPERATURE & TIME  
When all three shelves are in use to cook large quantities of food, it may be  
necessary to increase the cooking times given in the temperature charts by a few  
minutes, to allow for the loss of heat due to extra time taken to load the oven, and  
larger mass of food. Baking trays shold have an even gap around the oven.  
23  
 
Operation when using the Main Oven  
for Fan Cooking  
MAIN FAN OVEN OPERATION  
MAIN OVEN TEMPERATURE & FUNCTION CONTROL  
❍ ❍  
TIMER  
Step 1 Check that the timer is in manual.  
Step 2 Place the shelf/shelves in the correct position (see Main Oven Temperature  
Charts.  
Step 3 Place the food centrally on the shelf ensuring the oven door is fully closed.  
Step 4 Select the required cooking temperature (80 to 230˚C or MAX, depending on  
Model) by turning control (C) clockwise. The pilot light ( G ) will immediately  
come on, and remain on until the oven reaches the required temperature. The  
light will then automatically go off and on during cooking as the oven  
thermostat maintains the correct temperature.  
Note: When you have finished using your cooker, always return the controls to  
their OFF (O) position. At the end of the cooking period there may be a  
momentary puff of steam when the door is opened. This will disperse in a  
few seconds and is a perfectly normal characteristic of an oven with a good  
door seal.  
24  
 
Using the Main Oven for Other Functions  
FAN ONLY SETTING  
DEFROSTING FROZEN MEAT & POULTRY  
Joints of meat and whole birds should be defrosted slowly, preferably in a  
refrigerator (allowing 5-6 hours per lb.) or at room temperature (allowing 2-3  
hours per lb.).  
Frozen meat or poultry must be completely defrosted before cooking in the oven.  
However, to decrease the amount of time required to defrost food items, a non-  
heating fan only setting may be selected for the main oven only.  
OPERATION: TO ASSIST IN DEFROSTING:  
Place food in the oven and close the oven door.  
Turn the Main Oven Temperature and Function Control (C) clockwise to the  
setting.  
This defrosts by circulating the air around the food, time to defrost will depend  
on type and size of the food.  
NOTES: DO NOT defrost meat and poultry by warming the food through.  
Foods ideally suited to defrosting using the fan only setting are cream/cream  
cakes, butter cream filled cakes, gateaux, cheese cakes, iced cakes, quiches,  
pastries, biscuits, bread, croissants, fruit and many delicate frozen foods.  
If fish, meat and poultry are to be defrosted using the fan only setting, where  
possible it is recommended that the food should be small & thin.  
The items should be placed so that the maximum amount of surface area is  
exposed to the circulating air, and that they are turned regularly to ensure even  
defrosting.  
Larger cuts of meat and poultry may be defrosted by using the fan only setting  
up to a maximum weight of 2 kg (4lb 8oz).  
It is important to wash both meat and poultry and cooking utensils immediately  
after defrosting and before cooking. Food should be cooked immediately after  
defrosting.  
It is very important to strictly adhere to the basic principles of food handling and  
hygiene to prevent the possibility of bacterial growth.  
LIGHT ONLY SETTING  
When the Main Oven Temperature & Function Control (C) is turned clockwise to  
the  
setting, the main oven light only will illuminate.  
25  
 
Using the Main Oven for Other Functions  
‘S’ SLOW COOK SETTING  
This is used for slow cooking, keeping food warm and warming plates for short  
periods. Extra care should be taken when warming bone china, as it may be  
damaged in a hot  
oven.  
DO NOT place food or plates directly on the oven floor as this could damage both the oven  
lining and the plates which are being warmed.  
ADVANTAGES OF SLOW COOKING ARE:  
The oven stays cleaner because there is less splashing.  
Timing of food is not as critical, so there is less fear of overcooking.  
Inexpensive joints of meat are tenderised.  
Fully loading the oven can be economical.  
Cooking times can be extended in some cases by up to 2 hours.  
OPERATION:  
1. Place the prepared food in the main oven and ensure the door is fully closed.  
2. Select Slow Cooking Temperature ‘S’ by turning Main Oven Temperature &  
Function Control (C) clockwise.  
STORAGE & RE-HEATING OF FOOD:  
1. If food is to be frozen or not used immediately, place it in a clean container  
and cool as soon as possible.  
2. Always thaw frozen food completely in the refrigerator before re-heating.  
3. Always reheat food thoroughly and ensure it is piping hot before serving.  
4. Only re-heat food once.  
POINTS TO CONSIDER WHEN PREPARING FOOD FOR SLOW COOKING  
1. Make sure that the dishes to be used will fit into the oven ensuring enough room  
for air to circulate.  
2. All dishes cooked on the slow setting will require a minimum of 6 hours, however,  
it they are cooked for 1-2 hours longer then deterioration in their appearance  
may be noticed.  
3. Never cook joints of meat over 2.7kg (6 lb) or poultry over 2.0kg (4lb 8oz).  
We do not recommend that joints of meat or poultry are stuffed before cooking  
on the slow setting.  
4. To seal in the meat juices, always cook meat or poultry at 170oC for 30 minutes  
before wrapping in foil and placing on a rack over a tin (to allow good air  
circulation) before turning the control to the slow setting and cooking  
immediately.  
5. Always ensure that joints of pork and poultry are thoroughly cooked by checking  
with a meat thermometer before serving.  
6. Always thaw frozen foods completely before cooking. We do not recommend  
placing frozen food in the oven to cook.  
7. Always bring soups, liquids and casseroles to the boil before placing in the oven.  
8. Ensure that casserole dishes have a good seal (not airtight) and cover to the top  
with foil to prevent loss of moisture.  
9. Ensure that fruit and vegetables are cut into even sized small pieces to cook  
properly.  
10. Always adjust seasoning before serving.  
11. If using dried red kidney beans it is important that the beans are soaked and  
then boiled for a minimum of 10 minutes before using in any dish to destroy any  
toxins.  
12. When cooking fish or egg dishes it may be necessary to check during cooking to  
avoid overcooking.  
26  
 
Care and Cleaning  
Warning: Before cleaning, please ensure that the electricity supply to the appliance is switched off  
and the appliance is fully cold.  
1. “STAYCLEAN” OVEN LINERS (Top Oven Sides, Main Oven Sides and Rear Panel)  
TOP OVEN SIDES  
(a) How "Stayclean" works.  
The surfaces of the "Stayclean" oven liners (Main Oven  
rear panel) are treated with a special vitreous enamel  
which absorbs cooking soils. At temperatures of 220°C  
(425°F) or above, the special surface enables these soils  
to be slowly destroyed.  
The higher the temperature the more effective it is.  
(b) Cleaning.  
In most cases normal cooking operations at 220°C  
(425°F) will permit this cleaning operation to proceed  
during cooking. However if higher cooking temperatures  
are not used regularly, it may be necessary, in order to  
prevent heavy soiling, to run the ovens without shelves or  
meat pan, at a maximum setting for a couple of hours.  
It should not normally be necessary to clean the  
MAIN OVEN REAR PANEL  
AND SIDES  
"Stayclean" panels with water. If the user feels it is  
desirable to do so, wipe them over with a clean, soapy  
cloth, followed by a wipe with a clean damp cloth.  
DO NOT use biological washing powder, harsh abrasives or  
chemical oven cleaners of any kind as this could damage  
the “Stayclean” oven liners.  
27  
 
Care and Cleaning  
2. CLEANING GRILL, TOP OVEN AND MAIN OVEN  
(a) Base & Rear of Top Oven and Base of Main Oven.  
Wipe out the oven with a damp soapy cloth. For more  
stubborn stains on the base of the oven use a well  
soaped fine steel wool soap pad.  
GRILL  
PAN  
BASE &  
REAR  
OVEN  
SHELVES  
(b) Grill Pan & Oven Shelves.  
To prevent stains from being burnt on to the grill pan,  
food support and rod shelf, always wash immediately  
after use in warm soapy water.  
MAIN  
OVEN  
BASE  
Use a well soaped fine steel wool soap pad to remove  
stubborn stains from the rod shelves, grill pan, meat pan,  
anti-splash tray and the base of the oven.  
MEAT PAN  
DO NOT use aerosol cleaners on this oven as they could  
adversely affect the fan motor unit, and cannot be wiped off  
the fan blade.  
28  
 
Care and Cleaning  
3. OVEN DOORS  
(a) Control Panel  
CONTROL PANEL  
Regularly wipe with a clean, damp cloth and polish with a  
clean, dry cloth.  
(b) Inner Door Panels & Glass  
Open the door fully. The glass panel may now be washed.  
Stubborn stains can be removed by using a well soaped, fine  
steel wool soap pad.  
OVEN  
DOORS  
(c) Stainless trims (DY46X & BD42SS only)  
Regularly wipe with a clean, damp cloth and polish with a  
clean dry cloth.  
DO NOT use scouring pads, or abrasive powder, which will  
scratch the glass.  
29  
 
Care and Cleaning  
4. REPLACEMENT OF THE OVEN LAMP  
TOP OVEN LAMP  
Warning: To avoid electric shocks - please ensure that  
the electricity supply to the appliance is switched off and  
the appliance is fully cold, before removing the lamp lens.  
Open the oven door and remove the oven shelves.  
Using a thick cloth, grip the lamp lens, unscrew anti-  
clockwise and remove the lens.  
Carefully unscrew the bulb anti-clockwise.  
Fit replacement bulb (25W 300°C SES) and refit lens.  
MAIN OVEN LAMP  
5. HOW TO CLEAN THE LAMP LENS  
TOP OVEN LAMP  
Warning: To avoid electric shocks - please ensure that the  
electricity supply to the appliance is switched off and the  
appliance is fully cold, before cleaning lamp lens.  
Open the oven door and remove the oven shelves.  
Using a thick cloth, grip the lamp lens, unscrew anti-  
clockwise and remove.  
Clean with a non-abrasive cleansing cream and refit  
lamp lens.  
MAIN OVEN LAMP  
DO NOT use scouring pads, or abrasive powder, which will  
scratch the glass lens  
30  
 
Care and Cleaning  
Take particular care not to damage the inner surface of the door inner glass  
that is coated with a heat reflective layer. Do not use scouring pads, or  
abrasive powder, which will scratch the glass. Ensure that the glass panel is  
not subjected to any sharp mechanical blows.  
Stubborn stains can be removed by using a fine steel wool pad. For slight soiling  
the inner glass panel may be cleaned, while still warm, without removing it from  
the door. After cleaning, rinse and dry with a soft cloth.  
CLEANING THE DOORS  
SIDE OPENING DOORS  
Cleaning the door glass is the same as the drop down doors, except take care  
to support the weight of the inner glass when removing and refitting.  
DROP DOWN DOORS  
Remove the door inner glass as follows.  
1.  
Open the door fully and unscrew the two screws securing the glass  
panel so that the securing brackets can be turned. There is no need to  
remove the screws completely.  
2.  
Turn the brackets so that the glass can be removed and cleaned at the  
sink (Fig. 1.)  
Fig. 1.  
3.  
The inside of the outer door glass can now be cleaned while still fitted  
to the cooker.  
NEVER OPERATE THE COOKER WITHOUT THE INNER DOOR GLASS  
IN POSITION.  
Refit the door inner glass as follows.  
1.  
NOTE: The inner door glass has a special reflective coating on one side.  
Replace the door inner glass so that the statement: “IMPORTANT THIS  
FACE TOWARDS THE OVEN” can be read from the inner side of the  
door.  
2.  
Turn the two securing brackets back to  
their original position to retain the  
glass and tighten the screws. (Fig. 2.)  
Fig. 2.  
31  
 
Installation  
Electrical Requirements  
For your own safety, we recommend that your cooker is installed by a  
competent person such as one who is registered with NICEIC (National  
Inspection Council for Electrical Installation Contracting). The cooker should be  
installed in accordance with the latest edition of the IEE Regulations.  
Warning: This appliance must be earthed.  
Electrical Connections  
The installer must check that the voltage shown on the rating plate  
corresponds with the house electricity supply.  
The cooker must be supplied via a suitable double pole isolating switch, having a  
contact separation of at least 3mm in all poles placed in a readily accessible  
position adjacent to the cooker.  
If the cooker is to be wired into a connector unit, this may be positioned behind  
the cooker providing the following requirements are met:  
i) The connector unit must not project from the wall more than 25mm.  
ii) The top of the connector must not be more than 130mm above floor level.  
Remove the terminal cover at the rear base of the cooker. Pass the cable  
through the cable clamp and connect to the appropriate terminals provided.  
Allow sufficient cable for any future servicing.  
Tighten the screws on the cable clamp and replace the cover.  
Make main connections in the connector unit or cooker control unit.  
This appliance conforms to B.S. EN 55014 regarding suppression of Radio and  
Television reception interference.  
A double Pole control switch having a minimum rating of 32 amps should be used  
to feed the cooker using a suitably rated cable.  
Where a hob is fitted adjacent to or over the cooker, a 45 amp Double Pole  
control switch should be used to feed both units via separate suitably rated  
cables.  
We recommend a minimum of 4mm2 PVC insulated twin and earth cable  
conforming to B.S. 6004 for connection of each appliance.  
In all cases adhere to routing details (see fig. 4).  
This appliance must not be installed over any other appliance that generates  
heat such as a plinth heater.  
Note: Due to many different types of installation, a mains cable is not supplied  
with this product. The installer will fit the correct type and length of cable.  
32  
 
Installation  
Important  
It is essential that the lower cupboard is constructed in the manner illustrated  
i.e. having side, back, and roof panels so joined as to provide no apertures which  
could permit access to the oven unit when installed.  
1. General  
The appliance is designed for mounting at a safe level into an oven housing which  
must be secured to the backing wall.  
2. Ventilation  
a. The oven housing unit cabinet dimensions must comply with fig. 4.  
b. An air gap of 50mm minimum must be provided at the rear of any top or  
bottom cupboards or shelves (see fig. 1).  
c. It is necessary that the cabinets are provided with unobstructed ventilation,  
i.e. from adjacent cabinetry. This can be done by either raising the base of  
the cabinets using the adjusting feet (or spacers) or alternatively by  
providing a slot in the cabinet plinth to the dimensions in fig. 1.  
d. The air gap at rear allows the warmed air to pass out of the inner cabinet  
space. Where it is intended to fit cupboards above the oven unit to ceiling  
height, it is essential that the warmed air is exhausted through the front of  
the cabinet (see fig. 1).  
e. If an oven unit is installed adjacent to a tall cabinet, steam escaping from  
the oven when the door is opened could condense on and maybe stain the  
adjacent surface. To prevent permanent staining, the adjacent surface  
should be made of a material that is heat resisting and easy to clean.  
Adjacent tall cabinets should not be deeper than the oven housing cabinet.  
3. Final Installation  
a. Using a spirit level, check that the housing cabinet is level from side to side  
and from front to back in its installed position.  
b. Correct any unevenness by placing spacers under the bottom of the cabinet.  
Make sure that the cabinet rests firmly on the floor without rocking.  
c. Before the oven is fitted, the cabinet must be firmly secured to the backing  
wall for stability.  
d. The oven unit should now be lifted (this is a two person lift) into the cabinet  
and pushed fully home.  
e. Finally, the oven is secured to the cabinet by means of the four Phillips C/SK  
Head screws - two through each side trim.  
f. Remove all packaging material from the grill and oven interior.  
List of loose items:  
4 x Phillips C/SK Head No. 6 x 25mm screws.  
33  
 
Tall Cabinet Ventilation  
Fig. 1  
Ventilation Slot required  
here if cabinet does not  
fit to ceiling -51mm x 457mm min. area  
Ventilation Slot  
required  
here if the cabinet  
does fit to the ceiling  
- 51mm x 457mm min.  
area  
50mm  
Air Gap  
50mm  
Air Gap  
Ventilation Slot  
required here  
51mm x 457mm  
min. area  
34  
 
562mm  
Viewed down through cabinet  
Cabinet  
No. 6 x 25mm screw  
(4 supplied)  
Fig. 3  
870mm  
Oven Door  
Fig. 2  
882mm,  
870mm if  
cooker  
trim  
is to  
Connector  
6mm2  
overlap  
top edge  
of shelf  
Box  
Cable  
if hob fitted  
4mm2 Cable  
to Hob if  
4mm2  
fitted  
Cable  
To Oven  
Fig. 4  
* excluding pipe work  
and other projections  
35  
 
If something goes wrong...  
Before calling a Service Engineer, please check through the following lists.  
THERE MAY BE NOTHING WRONG.  
Problem  
Check  
Slight odour or small  
amount of smoke when  
grill / oven used first  
time  
This is normal and should cease after a short period.  
If you find that the timer display is blank, then it is likely that  
there is no electricity supply to your oven. Check:  
(i) That the main cooker wall is switched on  
Nothing Works  
(ii) Other appliances, to see if you have had a power cut  
(iii) The main circuit breaker for the property  
The power supply to your oven has possibly been  
Timer Display shows  
"0:00" with "Auto"  
Flashing  
interrupted, but has now come back on again. Reset the  
timer to the correct day and "Manual" operation using the  
instructions given in the timer section of the book.  
Main oven and Top  
ovens do not work,  
but the grill  
Your timer may be set for an Auto Cooking programme:  
Check the timer to see whether ‘Auto’ is lit or flashing. If it  
is then please follow the instructions given in the Timer  
section of this book to return the timer to Manual operation.  
works.  
Top oven and grill  
do not work, but  
Main oven works.  
Operating the cooker under the following conditions may  
cause a safety device to operate:  
(a)Grilling with the door closed - Always grill with the door  
fully open.  
(b)Grilling for an excessively long period at maximum setting  
- see Grilling guide.  
Switch off appliance and allow to cool for approx 30 mins.  
Switch the cooker back on and check that the Grill / Top  
oven is now operating.  
Grill keeps turning  
on and off  
When the Grill control is operating at less than its maximum  
setting, the Grill will cycle on and off, this is normal and not  
a fault.  
Timer buzzer / audible  
tone operates continually  
To cancel the audible tone press the minute minder button.  
Oven temperatures  
too high or low  
Check temperature and shelf positions are as recommended  
in the Oven Temperature Charts.  
It may be necessary to increase or decrease the  
recommended temperature slightly to suit your taste.  
Check:  
Oven does not cook  
evenly  
(a)Temperature and shelf positions are as recommended in  
the Oven Temperature Charts.  
(b)Oven utensils being used allow sufficient air flow around  
them.  
36  
 
If something goes wrong...  
Problem  
Check  
Grilling is uneven  
Ensure that Grill pan has been positioned as stated in the  
Grilling section of this book.  
The oven lamp is not covered by the guarantee. The part is  
easily changed (see the section on oven lamp replacement).  
A new lamp may be obtained from our Genuine Parts &  
Accessories Hotline (see ‘Key Contacts’, back page).  
Oven lamp does not work  
Condensation on the wall Steam and / or condensation may appear from the vent at  
at the rear of the  
cooker.  
the rear of the appliance when using an oven particularly for  
foods with a high water content e.g. frozen chips, roast  
chicken etc. This is normal, and any excess should be wiped  
off.  
Steam is a by - product of cooking any food with a high  
water contact. To help minimise always:  
Steam / Condensation  
in the oven after use.  
a)  
Try to avoid leaving food in the oven to cool after  
being cooked.  
b)  
Use a covered container, wherever possible.  
If you have been through the above list and there is still a problem,  
contact Service (see ‘Key Contacts’, back page).  
Disposal of your product  
To minimise the risk of injury to children please dispose of your product carefully and  
safely. Remove all doors and lids. Remove the mains cable (where fitted) by cutting off  
flush with the appliance and always ensure that no plug is left in a condition where it  
could be connected to the electricity supply.  
To help the environment, Local Authority instructions should be followed for the disposal  
of your product.  
Disposal of old electrical appliances  
The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment  
(WEEE), requires that old household electrical appliances must not be disposed of in the  
normal unsorted municipal waste stream. Old appliances must be collected separately in  
order to optimise the recovery and recycling of the materials they contain and reduce  
the impact on human health and the environment.  
The crossed out “wheeled bin” symbol on the product reminds you of your  
obligation, that when you dispose of the appliance it must be separately collected.  
Consumers should contact their local authority or retailer for information  
concerning the correct disposal of their old appliance.  
37  
 
Hotpoint Service Cover  
Hotpoint’s Extended Warranties  
Whether you have just one or a number of Hotpoint  
appliances in your kitchen, Hotpoint has a range of  
Service Plans to give you complete peace of mind.  
They enable you to extend your one year labour  
guarantee so that you can have repairs completed  
FREE during the membership period.  
Satisfaction Guaranteed or Your  
Money Back  
Hotpoint gives you a unique ‘Satisfaction Guaranteed’  
promise – valid for ninety days after you have  
purchased your Hotpoint product. If there is a  
technical problem with your Hotpoint appliance, just  
call Hotpoint Service (see back page). If necessary we  
will arrange for an engineer to call. If the technical  
problem is not resolved under this Guarantee,  
Hotpoint will replace your appliance or, if you prefer,  
give you your money back. Your statutory rights are  
not affected, and the Guarantee is additional and  
subject to the terms of Hotpoint’s Five Year Parts  
Guarantee.  
Service Cover  
We offer a number of payment methods; cheque,  
credit card or you can spread the cost and pay by  
direct debit (full details can be obtained on Free  
phone 0800 716356). This covers you for all repairs  
during the period of cover, which can be from 1 to 4  
years. Service Cover also includes loss of food, up  
to the value of £250, in refrigeration appliances.  
There is also an option of Service Cover with  
Maintenance at an additional cost. This includes an  
annual Electrical and Safety check and replacement  
of any parts as necessary.  
Hotpoint’s Free Five Year Guarantee  
From the moment your appliance is delivered  
Hotpoint guarantees it for FIVE YEARS.  
In the Five Years all replacement parts are FREE  
provided that they are fitted by our own Service  
Engineer. During the first year our Engineer’s time  
and labour is also free.  
Our guarantee covers loss of food in our  
refrigeration and freezer products up to £250  
during the first year, subject to verification by one  
of our engineers.  
After the first year we will charge for our  
Engineer’s time and labour. We do, however,  
operate a range of Service Plans (see opposite)  
which, for an annual payment, enables you to cover  
any repair costs which may be necessary.  
All our service repairs are guaranteed for twelve  
months in respect of our labour and any parts  
fitted.  
The appliance must be used in the United Kingdom,  
and must not be tampered with or taken apart by  
anyone other than our own Service Engineers.  
You may, however, buy parts which can be safely  
fitted without specialist knowledge or equipment.  
The correct fitting of such parts, provided they are  
genuine Hotpoint spares, will not affect your  
Guarantee. Parts are available from our Hotpoint  
Spares Centres (see back page).  
Kitchen Cover  
An annual payment covers you for all repairs for all  
your Hotpoint appliances which are less than ten  
years old. It also covers the cost of loss of food up  
to £250 in our refrigeration and freezer products.  
There is also the option of Kitchen Cover with  
Maintenance at an additional cost. Any additional  
Hotpoint appliances purchased after you have  
joined Hotpoint Kitchen Cover will automatically be  
included during the annual period of cover without  
further charge.  
Appliance Registration  
To ensure that you have the opportunity to benefit  
from any of the above Service Schemes and other  
offers you should complete and return immediately  
the Appliance Registration Form/Questionnaire  
supplied with this appliance. Full details and costs of  
our Service Schemes, together with an application  
form, will be sent to you at the end of the first year  
of the guarantee.  
Annual Safety/Maintenance Checks  
Hotpoint strongly recommends that all its  
appliances are regularly checked for electrical and  
mechanical safety, whether or not they are covered  
by a Service Plan. Worn door gaskets or hoses may  
cause a leak on an appliance, which could become  
dangerous if neglected.  
Our guarantee does not cover the cost of any  
repair, or loss of food in refrigeration products,  
due to power failure, accidents or misuse. Nor does  
it cover the cost of any visits to advise you on the  
use of your appliance. Please read thoroughly the  
instruction book supplied with this appliance.  
If at any time during the Guarantee period we are  
unable to repair your appliance, we will refund any  
repair costs paid to us in the previous twelve  
months. We will also offer you a new appliance at a  
reduced charge instead of a repair.  
Proof of Purchase  
For future reference please attach your purchase  
receipt to this booklet and keep it in a safe place.  
Our Guarantee is in addition to and does not affect  
your legal rights.  
Spares and Accessories  
Spares and accessories can be ordered from your  
local Hotpoint Spares Centre (see back page), using  
the order form enclosed.  
Should you need independent advice on your  
consumer rights, help is available from your  
Consumer Advice Centre, Law Centre, Trading  
Standards Department and Citizens Advice Bureau.  
All Hotpoint servicing is carried out by our own  
Service Organisation located throughout the  
United Kingdom and Eire. We will be happy to deal  
with any problems which you may have.  
NOTE: Our Engineers will use every effort to avoid  
damage to floor coverings and adjacent units when  
carrying out repairs/service work, but in locations  
where the Engineer advises you that it will be  
impossible to move appliances without risk of  
damage, he will only proceed with your approval  
that no liability is accepted.  
38  
 
Notes  
39  
 
Key Contacts  
After Sales Service  
Over 1100 trained specialists, directly employed by us, ensure that you can have  
complete confidence in both the appliances and services we offer.  
Repair Service and Information Help Desk  
UK: 08709 066 066  
Monday to Friday, 8am to 7.30pm  
Saturday, 8.30am to 5.30pm  
Sunday, 9.30am to 3.30pm  
Republic of Ireland: 0818 313 413  
Note: Our operators will require the following information:  
Model number  
Serial number  
Extended Warranties  
UK: 08709 088 088  
Monday to Sunday, 8am to 8pm  
Republic of Ireland: 0123 002 333  
Genuine Parts and Accessories  
UK: 08709 077 077  
Monday to Friday, 8.30am to 5pm  
Saturday, 8.30am to 12noon  
Republic of Ireland: 0818 313 413  
Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB  
.
PRINTED BY SIMLEX FOUR ASHES, WOLVERHAMPTON.  
09/2006 Part no. 195059689.00  
 

Graco Baby Playpen PD196635A User Manual
Graco Baby Swing PD162173B User Manual
Hamilton Beach Oven 32180C User Manual
Handspring PDAs Smartphones Visor Prism User Manual
Hotpoint Dishwasher HDA750 User Manual
Hotpoint Refrigerator FF50 User Manual
HP Hewlett Packard Switch zl User Manual
HTC Cell Phone NIKI160 User Manual
Husqvarna Trimmer 335RJ 335RJX Series User Manual
IBM Computer Hardware XSERIES 220 User Manual