GC640IX
GC640WH
GC640BK
GC751TX
GC750X
GC641IX
GCD641IX
GCA641IX
GCB641X
GCB640X
GC641IK
GCL640TK
GCL641TX
GC640TK
GCB751X
English
Operating Instructions
HOB
Contents
Operating Instructions,1
Warnings,2
Assistance,2
Description of the appliance,3
Installation,4
Start-up and use,8
Precautions and tips,8
Maintenance and care,9
Troubleshooting,9
After Sales Service,11
Guarantee,12
08448 24 24 24
Please phone us on
guarantee
to activate your
Description of the appliance
Overall view
1
2
3
4
5
Support Grid for COOkWArE
GAs BurnErs
Control Knobs for GAs BurnErs
Ignition for GAs BurnErs*
sAfEty DEvICEs*
•
GAs BurnErs differ in size and power. Use the diameter of the cookware
to choose the most appropriate burner to cook with.
•
•
•
GAs BurnEr IGnItIOn*enables a specific burner to be lit automatically.
Control Knobs for gas burners adjust the size of the flame.
sAfEty DEvICE* stops the gas flow if the flame is accidentally
extinguished.
* Only available on certain models.
2
2
1
1
3
3
5
4
3
fitting the appliance
The following precautions must be taken when installing the hob:
Installation
! Before operating your new appliance please read this instruction booklet
carefully. It contains important information for safe use, installation and care
of the appliance.
GB
•
•
•
Kitchen cabinets adjacent to the appliance and taller than the top of the
hob must be at least 600 mm from the edge of the hob.
Hoods must be installed according to their relative installation instruction
manuals and at a minimum distance of 650 mm from the hob (see figure).
Place the wall cabinets adjacent to the hood at a minimum height of 420
mm from the hob (see figure).
! Please keep these operating instructions for future reference. Pass them on
to possible new owners of the appliance.
If the hob is installed beneath a wall cabinet,
the latter must be situated at a minimum of
700 mm above the hob.
Positioning
!Keep packaging material out of the reach of children. It can become a choking
or suffocation hazard (see Precautions and tips).
600mm min.
! The appliance must be installed by a qualified professional according to the
instructions provided. Incorrect installation may cause harm to people and
animals or may damage property.
! This unit may be installed and used only in permanently ventilated rooms
in accordance with current national regulations. The following requirements
must be observed:
Before the installation remove the grids and burners from the hob and turn it
upside down, making sure you don’t damage the thermocouples and spark
plugs.
•
The room must be equipped with an air extraction system that expels
any combustion fumes. This may consist of a hood or an electric fan that
automatically starts each time the appliance is switched on.
Apply the seals that come with the
appliance along the outer edges of
the hob to prevent any passage of air,
humidity and water (see Figure).
For proper application make sure the
surfaces to be sealed are clean, dry and
free of any grease/oil.
•
The installation cavity should have the dimensions indicated in the figure.
Fastening hooks are provided, allowing you to fasten the hob to tops that
are between 20 and 40 mm thick. To ensure the hob is securely fastened
In a chimney stack or branched flue.
(exclusively for cooking appliances)
Directly to
the Outside
to the top, we recommend you use all the hooks provided.
55 mm
•
The room must also allow proper air circulation, as air is needed for
combustion to occur normally. The flow of air must not be less than 2 m3/h
per kW of installed power.
475
mm
The air circulation system may take air directly
from the outside by means of a pipe with an
inner cross section of at least 100 cm2; the
opening must not be vulnerable to any type
555 mm
A
of blockages.
Hook fastening diagram
Examples of
ventilation holes
for comburant air.
The system can also provide the air needed
Adjacent
Room
Room to be
Vented
for combustion indirectly, i.e. from adjacent
rooms fitted with air circulation tubes as
described above. However, these rooms must
not be communal rooms, bedrooms or rooms
that may present a fire hazard.
Hooking position for top H=20mm
Hooking position for top H=30mm
front
Enlarging the ventilation slot
between window and floor.
•
Liquid petroleum gas sinks to the floor as it is heavier than air. Therefore,
rooms containing LPG cylinders must also be equipped with vents to allow
gas to escape in the event of a leak. As a result LPG cylinders, whether
partially or completely full, must not be installed or stored in rooms or
storage areas that are below ground level (cellars, etc.). It is advisable to
keep only the cylinder being used in the room, positioned so that it is not
subject to heat produced by external sources (ovens, fireplaces, stoves,
etc. ) which could raise the temperature of the cylinder above 50°C.
Hooking position for top H=40mm
Back
! Use the hooks contained in the “accessory pack”.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
4
•
Where the hob is not installed over a built-in oven, a wooden panel must
be installed as insulation. This must be placed at a minimum distance of
20 mm from the lower part of the hob.
•
The socket or double-pole switch are easily accessible when the appliance
is installed.
GB
! The wires in the mains lead are coloured in accordance with the following
code:
ventilation
To ensure adequate ventilation, the back panel of the cabinet must be
removed. It is advisable to install the oven so that it rests on two strips of
wood, or on a completely flat surface with an opening of at least 45 x 560
mm (see diagrams).
Green & Yellow
Blue
Brown
- Earth
- Neutral
- Live
As the colours of the wires in the mains lead may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
Connect the Green & Yellow wire to terminal marked “E” or
or coloured
Green or Green & Yellow.
Connect the Brown wire to the terminal marked “L” or coloured Red or Brown.
Connect the Blue wire to the terminal marked “N” or coloured Black or Blue.
FAILURE TO OBSERVE THE ACCIDENT-PREVENTION REGULATIONS
RELIEVES THE MANUFACTURER OF ALL LIABILITY.
! The hob can only be installed above built-in ovens with a cooling ventilation
replacing the cable
Use a rubber cable of the type H05RR-F with a suitable cross section 3 x
0.75 mm².
system.
Where a hob is installed above an oven without a forced ventilation cooling
system, adequate ventilation must be provided inside the cabinet by means
of air holes through which air can pass (see figure).
The yellow-green earth wire must be 2-3 cm longer than the other wires.
Gas connection
The appliance should be connected to the main gas supply or to a gas
cylinder in compliance with current national regulations. Before carrying out
the connection, make sure the cooker is compatible with the gas supply you
wish to use. If this is not the case, follow the instructions indicated in the
paragraph “Adapting to different types of gas.”
When using liquid gas from a cylinder, install a pressure regulator which
complies with current national regulations.
!Check that the pressure of the gas supply is consistent with the values indicated
inTable 1 (“Burner and nozzle specifications”).This will ensure the safe operation
and longevity of your appliance while maintaining efficient energy consumption.
Electrical connection
! THIS APPLIANCE MUST BE EARTHED.
The hob is designed to work with alternating current, the supply voltage and
frequency indicated on the rating plate (situated under the hob). Make sure
that the local supply voltage corresponds to the voltage indicated on the
rating plate.
Connection with a rigid pipe (copper or steel)
! Connection to the gas system must be carried out in such a way as not to
place any strain of any kind on the appliance.
There is an adjustable L-shaped pipe fitting on the appliance supply ramp
and this is fitted with a seal in order to prevent leaks. The seal must always
be replaced after rotating the pipe fitting (seal provided with appliance). The
gas supply pipe fitting is a threaded 1/2 gas cylindrical male attachment.
Connecting the supply cable to the mains electricity supply
For models supplied without a plug, fit a standard plug suitable for the load
indicated on the rating plate, onto a cable and connect to a suitable socket.
To connect direct to the mains supply, a double pole switch with a contact
separation of at least 3mm suitable for the load and complying with current
standards and regulations must be fitted between the appliance and the
mains supply outlet.
The green-yellow earth wire must not be interrupted by the switch.
The supply cable must be positioned so that no part of it reaches a temperature
of 50°C above room temperature. For installation above a built-under
oven, the hob and the oven must be connected separately to the electricity
supply, both for safetly reasons and for easy removal of the oven for repair,
maintenance etc.
Connecting a flexible jointless stainless steel pipe to a threaded
attachment
The gas supply pipe fitting is a threaded 1/2 gas cylindrical male attachment.
These pipes must be installed so that they are never longer than 2000 mm
when fully extended. Once connection has been carried out, make sure that
the flexible metal pipe does not touch any moving parts and is not compressed.
! Only use pipes and seals that comply with current national regulations.
Checking the tightness of the connection
DO NOT use adapters as they could cause overheating or burning.
! When the installation process is complete, check the pipe fittings for leaks
using a soapy solution. Never use a flame.
Before connecting to the power supply, make sure that:
•
The limiter switch and the domestic system can withstand the load from
The appliance (see rating plate).
The supply system is efficiently earthed according to standards and laws
in force.
Adapting to different types of gas
To adapt the hob to a different type of gas other than default type (indicated
on the rating plate at the base of the hob or on the packaging), the burner
nozzles should be replaced as follows:
•
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
5
1. Remove the hob grids and slide the burners off their seats.
2. Unscrew the nozzles using a 7 mm socket spanner, and replace them
with nozzles for the new type of gas (see table 1 “Burner and nozzle
characteristics”).
DATA PLATE
GB
Electrical
connections
see data plate
3. Reassemble the parts following the above procedure in the reverse order.
4. Once this procedure is finished, replace the old rating sticker with one
indicating the new type of gas used. Sticker are available from any of our
Service Centres.
This appliance conforms to the following
European Economic Community directives:
- 2006/95/EEC dated 12/12/06 (Low
Voltage) and subsequent amendments
- 2004/108/EEC dated 15/12/04
(Electromagnetic Compatibility) and
subsequent amendments
replacing the triple ring burner nozzles
1. Remove the pan supports and lift the burners out of their housing. The
burner consists of two separate parts (see pictures).
2. Unscrew the nozzles using a 7 mm socket spanner. Replace the nozzles
with models that are configured for use with the new type of gas (see Table
1). The two nozzles have the same hole diameter.
- 93/68/EEC dated 22/07/93 and
subsequent amendments.
- 2009/142/EEC dated 30/11/09 (Gas) and
subsequent amendments.
- 2012/19/EC and subsequent
amendments.
3. Replace all the components by completing the above operations in reverse
order.
•
Adjusting the burners’ primary air
Does not require adjusting.
•
Setting the burners to minimum
1. Turn the tap to the low flame position;
2. Remove the knob and adjust the adjustment screw, which is positioned
in or next to the tap pin, until the flame is small but steady.
3. Having adjusted the flame to the required low setting, while the burner is
alight, quickly change the position of the knob from minimum to maximum
and vice versa several times, checking that the flame does not go out.
4. Some appliances have a safety device (thermocouple) fitted. If the device
fails to work when the burners are set to the low flame setting, increase
this low flame setting using the adjusting screw.
5. Once the adjustment has been made, replace the seals on the by-passes
using sealing wax or a similar substance.
! If the appliance is connected to liquid gas, the regulation screw must be
fastened as tightly as possible.
! Once this procedure is finished, replace the old rating sticker with one
indicating the new type of gas used. Stickers are available from any of our
Service Centres.
! Should the gas pressure used be different (or vary slightly) from the
recommended pressure, a suitable pressure regulator must be fitted to the
inlet pipe (in order to comply with current national regulations).
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
6
Burner and nozzle specifications
GB
Table 1
Liquid Gas
Natural Gas
Burner
Diameter Thermal
Thermal By-pass Nozzle
Flow*
(g/h)
Thermal Nozzle
Flow*
(l/h)
power
kW
power
kW
1/100
1/100
power
kW
1/100
(p.c.s.*)
(p.c.s.*)
(p.c.s.*)
Nominal
(mm)
100
Reduced Nominal (mm)
(mm)
86
***
**
214
(mm)
Fast (R)
0.70
0.70
0.40
0.40
1.50
0.70
3.00
2.60
1.65
1.00
3.30
3.40
39
39
28
28
61
39
218
189
120
73
3.00
2.60
1.65
1.00
3.60
3.40
132 (H)
286
248
157
95
Reduced Fast (RR)
Semi Fast (S)
Auxiliary (A)
100
75
80
64
186
118
71
122 (H)
96 (Z)
55
50
79 (6)
Triple Crown (TC)
Ultrarapid (UR)
Supply pressures
130
100
65x2
91
240
247
236
243
103x2
138 (H)
343
324
Nominal (mbar)
Minimum (mbar)
Maximum (mbar)
28-30
20
37
25
45
20
17
25
35
*
**
***
At 15°C and 1013,25 mbar - dry gas
Propane P.C.S. = 50.37 MJ/Kg
Butane P.C.S. = 49.47 MJ/Kg
Natural P.C.S. = 37.78 MJ/m³
A
S
A
RR
A
RR
A
S
S
S
S
RR
TC
R
S
UR
TC
S
GC750X
GC751X
GC751TX
GC640IX
GC640TIX
GCL640TK
GCL641TX
GC640TK
GC640WH
GC640BK
GC641IX
GCD641IX
GCA641IX
GCB641X
GCB640X
GC641IK
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
7
General safety
start-up and use
! The position of the corresponding gas burner is shown on every knob.
GB
•
•
This is a class 3 built-in appliance.
gas appliances require regular air exchange to maintain efficient
operation. When installing the hob, follow the instructions provided
in the paragraph on “Positioning” the appliance.
These instructions are only valid for the countries whose symbols
appear in the manual and on the serial number plate.
The appliance was designed for domestic use inside the home and is not
intended for commercial or industrial use.
The appliance must not be installed outdoors, even in covered areas. It is
extremely dangerous to leave the appliance exposed to rain and storms.
Do not touch the appliance with bare feet or with wet or damp hands and
feet.
The appliance must be used by adults only for the preparation of food,
in accordance with the instructions outlined in this booklet. any other
use of the appliance (e.g. for heating the room) constitutes improper
use and is dangerous. The manufacturer may not be held liable for
any damage resulting from improper, incorrect and unreasonable
use of the appliance.
Gas burners
•
•
•
•
•
Each burner can be adjusted to one of the following settings using the
corresponding control knob:
●
Off
Maximum
Minimum
To light one of the burners, hold a lit match or lighter near the burner and, at
the same time, press down and turn the corresponding knob anti-clockwise
to the maximum setting.
Since the burner is fitted with a safety device, the knob should be pressed
for approximately 2-3 seconds to allow the automatic device keeping the
flame alight to heat up.
•
•
•
•
•
•
Ensure that the power supply cables of other electrical appliances do not
come into contact with the hot parts of the oven.
The openings used for ventilation and dispersion of heat must never be
covered.
Always make sure the knobs are in the “”/“” position when the appliance
is not in use.
When unplugging the appliance always pull the plug from the mains socket,
do not pull on the cable.
Never carry out any cleaning or maintenance work without having detached
the plug from the mains.
In case of malfunction, under no circumstances should you attempt to repair
the appliance yourself. Repairs carried out by inexperienced persons may
cause injury or further malfunctioning of the appliance. Contact a Service
Centre (see Assistance).
! If a flame is accidentally extinguished, turn off the control knob and wait for
at least 1 minute before trying to relight it.
To switch off the burner, turn the knob in a clockwise direction until it stops
(when reaches the “●” position).
Practical advice on using the burners
To ensure the burners operate efficiently:
•
Use appropriate cookware for each burner (see table) so that the flames
do not extend beyond the bottom of the cookware.
•
•
Always use cookware with a flat base and a cover.
When the contents of the pan reach boiling point, turn the knob to minimum.
•
•
Always make sure that pan handles are turned towards the centre of the
hob in order to avoid accidental burns.
Do not close the glass cover (if present) when the gas burners or electric
hotplates are still hot.
Do not leave the electric hotplate switched on without a pan placed on it.
Do not use unstable or deformed pans.
remove any liquid from the lid before opening it.
The appliance should not be operated by people (including children)
with reduced physical, sensory or mental capacities, by inexperienced
individuals or by anyone who is not familiar with the product. These
individuals should, at the very least, be supervised by someone who
assumes responsibility for their safety or receive preliminary instructions
relating to the operation of the appliance.
Do not let children play with the appliance.
The appliance is not intended to be operated by means of an external
timer or separate remote-control system.
Burner
Ø Cookware Diameter (cm)
Fast (R)
24 - 26
24 - 26
16 - 20
10 - 14
24 - 26
Reduced Fast (RR)
Semi Fast (S)
Auxiliary (A)
•
•
•
•
Triple Crown (TC)
Pans to be used on 60 cm hobs
Burner
Ø Cookware Diameter (cm)
Reduced Rapid (RR)
Semi-Rapid (S)
Auxiliary (A)
24 - 26
16 - 20
10 - 14
24 - 26
24 - 26
•
•
Triple Crown (TC)
Ultra Rapid (UR)
Disposal
•
Pans to be used on 75 cm hobs
When disposing of packaging material: observe local legislation so that the
packaging may be reused.
To identify the type of burner, refer to the designs in the section entitled, “Burner
and Nozzle Specifications”.
•
The European Directive 2012/19/EC on Waste Electrical and Electronic
Equipment (WEEE), requires that old household electrical appliances
must not be disposed of in the normal unsorted municipal waste stream.
Old appliances must be collected separately in order to optimise
the recovery and recycling of the materials they contain and reduce
the impact on human health and the environment. The crossed out
“wheeled bin” symbol on the product reminds you of your obligation,
that when you dispose of the appliance it must be separately collected.
Consumers may take their old appliance to public waste collection
Precautions and tips
! This appliance has been designed and manufactured in compliance with
international safety standards. The following warnings are provided for safety
reasons and must be read carefully.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
8
areas, other communal collection areas, or if national legislation
allows return it to a retailer when purchasing a similar new product.
All major household appliance manufacturers are active in the creation of
systems to manage the collection and disposal of old appliances.
the burner does not remain lit when set to minimum.
Check to make sure that:
GB
•
•
•
The gas holes are not blocked.
There are no draughts near the appliance.
The minimum setting has been adjusted properly.
the cookware is unstable.
Check to make sure that:
Maintenance and care
•
•
•
The bottom of the cookware is perfectly flat.
The cookware is positioned correctly at the centre of the burner.
The pan support grids have been positioned correctly.
switching the appliance off
Disconnect your appliance from the electricity supply before carrying out
any work on it.
Cleaning the appliance
! Do not use abrasive or corrosive detergents such as stain removers, anti-rust
products, powder detergents or sponges with abrasive surfaces: these may
scratch the surface beyond repair.
! Never use steam cleaners or pressure cleaners on the appliance.
•
•
•
It is usually enough to wash the hob with a damp sponge and dry it with
absorbent kitchen roll.
The removable parts of the burners should be washed frequently with
warm water and soap and any burnt-on substances removed.
For hobs which ligth automatically, the terminal part of the electronic instant
lighting devices should be cleaned frequently and the gas outlet holes
should be checked for blockages.
•
Stainless steel can be marked by hard water that has been left on the
surface for a long time, or by aggressive detergents containing phosphorus.
After cleaning, rinse and dry any remaining drops of water.
Gas tap maintenance
Over time, the taps may become jammed or difficult to turn. If this happens,
the tap must be replaced.
! This procedure must be performed by a qualified technician authorised
by the manufacturer.
troubleshooting
It may happen that the appliance does not function properly or at all. Before
calling the service centre for assistance, check if anything can be done. First,
check to see that there are no interruptions in the gas and electrical supplies,
and, in particular, that the gas valves for the mains are open.
The burner does not light or the flame is not even around the burner.
Check whether:
•
•
•
The gas holes on the burner are clogged.
All the movable parts that make up the burner are mounted correctly.
There are draughts near the appliance.
The flame dies in models with a safety device.
Check to make sure that:
•
•
•
You pressed the knob all the way in.
You keep the knob pressed in long enough to activate the safety device.
The gas holes are not blocked in the area corresponding to the safety
device.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
9
GB
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
10
After sales service
GB
No one is better placed to care for your Hotpoint appliance during the course of its working life than us – the
manufacturer.
Essential Contact Information
Hotpoint Service
We are the largest service team in the country offering you access to 400 skilled telephone advisors and 1000
fully qualified engineers on call to ensure you receive fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically
clean your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts guarantee you
must register your appliance with us.
UK: 08448 24 24 24
Republic of Ireland: 01 230 0800
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17
Recycling and Disposal Information
As part of Hotpoint’s continued commitment to helping the environment, Hotpoint reserves the right to use
quality, recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the
door, plug, and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that
the appliance can no longer be plugged into mains socket, and the door cannot be locked shut.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
11
195097584.04
01/2014 - XErOX fABrIAnO
Guarantee
GB
12 months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for
twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our operating and
maintenance instructions.
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by
any person not authorised by us.
-
-
-
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper
installation
Replacement of any consumable item or accessory. These included but not limited to: plugs, cables,
batteries, light bulbs, fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-
DOMESTIC PREMISES.
5 Year Parts Guarantee
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering
your appliance with us and the parts being fitted by one of our authorised engineers. There will be a charge for
our engineer’s time. To activate the extra parts warranty on your appliance, simply call our registration line on
08448 24 24 24 (Republic of Ireland 01 230 0800)
Extended Guarantees
We offer a selection of protection plans that enable you to fully cover yourself against the expense of repair bills
for the life of your policy. To find the ideal plan for you please call our advice line on 08448 226 226 (Republic of
Ireland 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you experience
any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service Hotline on 08448
224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where necessary, to arrange for an
engineer to call.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
12
|